Search Documents

By R. D. Nelson, F. E. Bowman

Evidence has been found for a (010)a?(111)B[102]a /,11[341]/B crystallographic relationship between the monoclinic a and B phases of plutonium during the a?B transformation. The results of an X-ray diffraction study, where [010] fiber textured a samples were used in the absence of suitable single crystals indicate that the (OIO)a planes become (111)B planes upon transformation under near-equilibrium conditions. The transformation strain along the fiber axis, which was the [010] direction, was measured dila-tomekically; the measured 8.5 pct expansion compares favorably with the 8.44 pct expansion in the in-terplanar spacing represented by the (010)a?(111)B relationship. From plots of the atom positions in each of the related planes, a correspondence was deduced between the [102]a, direction and the [341]B direction. Further analysis of the two lattice structures in the light of this relationship revealed a rotation about the [102] direction of 1 deg 43 min and a slight shearing in this same direction of about 30 min. THIS paper discusses the (B crystal structure of plutonium and the orientation relationship existing between the monoclinic a and B phases during the a?ß transformation. The kinetics of the a?ß and (3 — a transformations have received extensive consideration, and because of the crystallographic complexity of these phases, the question of the mechanisms by which these transformations occur is especially intriguing. Nelson and Shyne1 evaluated the existing experimental evidence and concluded, from the indirect evidence available, that both the ß ? a and a ? ß transformations occur by a martensitic process. Their data reveal the anisotropic nature of these transformations which suggests the existence of specific crystallographic relationships between the parent and product phases. In this paper, we are concerned with the confirmation of the existence of such a relationship resulting from the a ? ß transformation and the derivation of the crystallographic details necessary to specify it. EXPERIMENTAL RESULTS X-ray diffraction and dilatometric data were obtained from samples of a plutonium having a [010] fiber texture. These cylindrical specimens, approximately 1 cm in diam, were prepared by transforming the ß phase to a under the influence of a uniaxially applied compressive load.' The [0l0] direction is parallel to the direction of applied stress; it is also perpendicular to the (010) planes. This correspondence between the plane normal and the direction having the same indices is, in the monoclinic a plutonium structure, restricted solely to this (010)[010] combination. Such a specimen was mounted in an evacuated, elevated temperature specimen holder on an X-ray dif-fractometer so that the diffracting surface was perpendicular to the fiber axis. The a diffraction pattern, Fig. 1, taken at about 115ºC, revealed the predominance of the (020) reflection. This monoclinic, P 21/rn space group yields no (0k0) reflections when k is odd. The temperature was raised slowly to 160°C to effect the complete transformation to the phase; then it was lowered to 120°C so that a diffraction pattern of the ß could be obtained near the a = ß equilibrium temperature for direct comparison with the a at the same temperature. The (3 diffraction pattern, Fig. 2, obtained under these conditions showed a (222) reflection relatively much more intense than in the random pattern. The other reflections appearing with sig-

Jan 1, 1970

By John A. Prof. Church

ONE of the most striking phenomena connected with the mines on the Comstock lode is the extreme heat encountered in the lower levels. This heat is not due to the burning of candles, heat of the men, and decomposition of timbers, all intensified by bad ventilation, as was the case nearer the surface. It proceeds from the rock, which maintains constantly a temperature very much higher than the average of the atmosphere in Nevada. The heat of these mines is a matter of more than usual interest, for they are the only hot ones now worked in the United States, and both in the present temperature encountered and in the increase which is to be expected as greater depths are reached, they appear to surpass any foreign mines of which we have a record. Hot mines are known also in other countries, as in the tin and copper lodes of Wales, where one of the veins worked by the United Mines is known as the hot lode. It has springs which discharge water at a temperature of 116° Fahrenheit, the depth being 220 fathoms, or 1320 feet. The heat of the air in these workings is given at 100° to 113° Fahrenheit. The air is bad, and the heat in the drifts seems to be traceable to defective ventilation rather than to the real necessities of the case. Air is supplied through a small pipe, and is drawn from a place where the temperature is 95° Fahrenheit. Under such circumstances it is not surprising to read that in this hot mine the air is hotter than the rock, a state of things which I have never observed in the Comstock. Other mines have been reported to the British Coal Committee as having temperatures of 106° Fahrenheit and thereabouts, but the only positive comparisons that are available at this writing are the following, all from Cornish mines * Read by permission of Lieut. Geo. M. Wheeler, Corps of Enginerrs, U. S. Arm J, in charge of U. S. Geographical and Geological Surveys, west of the 100th meridian.

Jan 1, 1879

By Ted C. Briggs

Nitrogen exists in two broad categories commonly designated as elemental nitrogen and fixed nitrogen. Elemental nitrogen is found in nature as a diatomic molecule and constitutes about 78%, by volume, of the earth's atmosphere. Fixed nitrogen is a common term used for nitrogen that is chemically bound to other elements. Although elemental nitrogen is very abundant, nonleguminous plants cannot utilize nitrogen unless it is in the chemically combined form. The content of this chapter is confined to fixed nitrogen since the uses and properties of elemental nitrogen and the fixed nitrogen compounds are different. Bacteria associated with legumes are able to fix atmospheric nitrogen, but not to the extent or in the locations required by modem agriculture. The need to use fertilizers containing fixed nitrogen compounds to grow food crops has been recognized for hundreds of years, and from antiquity farmers have used organic wastes such as animal manures, vegetable wastes, sewage sludge, fish scraps, etc., containing these compounds for fertilizers. The organic materials have a low nitrogen content, however, and cannot support large-scale food production. Known commercial-size deposits of natural nitrates containing much higher nitrogen content exist only in Chile, and the possibility of the discovery of other significant deposits is remote. The Chilean deposits were the major source of nitrogenous fertilizers until about 1913, when the Haber-Bosch process for the production of synthetic ammonia was developed. In the Haber-Bosch process, nitrogen reacts with hydrogen, at high temperatures and pressures and in the presence of a catalyst, to form ammonia. At present Chile is the only country in the world with a nitrate mining industry, and, although the mining of natural nitrates is an important industry in Chile, natural nitrates are relatively unimportant, worldwide, because of the adoption of fixed nitrogen processes. The relative amount of the world demand for fixed nitrogen that is derived from natural nitrates has declined in recent years and will continue to decline. Modern farmers are sophisticated in economic calculations such as cost to benefit ratios and, for the most part, they purchase plant nutrients which give the highest return on their investment. Natural nitrates cannot compete on a fixed-nitrogen cost basis with anhydrous ammonia and its derivative products. In a limited sense, the fixed nitrogen industry is mining the air. Modern plants use air, water, and, in most cases, natural gas to produce the ammonia that is now the key building block of the fixed nitrogen industry. To present an accurate picture of the industry, this chapter on nitrogen follows a format somewhat different from that of other chapters in this volume.

Jan 1, 1975

By W. J. Helfrich, C. L. Sollenberger

Many present direct reduction processes utilize iron ore concentrates for the production of sponge iron and the sponge iron is usually preferred as an agglomerate. Pelletizing a high grade iron oxide concentrate prior to reduction is a simple approach to the high capacity production of a uniform and agglomerated sponge iron product. The present paper describes the effect of different atmospheres and physical characteristics on the reduction of pelletized iron oxide concentrates. The kinetics of iron oxide reduction have been I studied by numerous investigators1-4 and a rate equation for the hydrogen reduction of hematite and magnetite has been proposed. Mc Kewan' obtained kinetic data for the reduction of hematite spheres sintered at 13'70°C (2498'F'). The kinetics of magnetite reduction was studied by Quets. He compacted the oxide at a pressure of 1 ton per sq cm and sintered the specimens to densities of 95 to 96 pct of theoretical. These studies demonstrated that the reduction of iron oxide is a topochemical process and that the rate of reduction is proportional to the receding surface area of remaining iron oxide. Thus, the measurement of the kinetics of iron oxide reduction depends upon the development of a measurable and well defined interface between metal and reacting oxide. It is evident that the reduction rate will be constant only when the rate of formation of the reaction product layer is constant. It was recognized by Joseph' and Edstrom' that the physical character of the oxide will determine the configuration of the interface between oxide and metal. The reduction of oxides which exhibit few pores or no interconnected pores should proceed by topochemical processes. However, if a massive or dense crystalline ore cracks during the reduction of the oxide, thus allowing the reduction to Proceed away from a well defined oxide/metal interface, then the observed reduction rate will vary or change during reduction. From a process standpoint, it would be difficult to apply absolute reduction rates determined for crystalline or nonporous iron oxide to the direct reduction of a porous pellet of iron ore concentrate. Most present direct reduction processes are attempts to utilize iron ore concentraates in the production of sponge iron. The sponge iron is usually preferred in an agglomerated form for subsequent melting practices. Pelletizing a high grade iron oxide concentrate prior to reduction is a simple approach to the high capacity production of a uniform and agglomerated sponge iron product. One process for preparing such a product has already been de-scribed. This paper describes the effect of different atmospheres and physical characteristics on the reduction of pelletized iron oxide concentrates. ORE CONCENTRATES STUDIED A magnetite concentrate from Reserve Mining Co. and a hematite concentrate from U.S. Steel Corp. were used in preparing pellets for these experiments. A head analysis of these concentrates is given in Table I. To compare the reduction rates of pelletized concentrates, it was necessary that each pellet contain equal amounts of oxygen which could be removed by reduction, regardless of the oxidation state, i.e., Fez% or Fe304. Also, because of the difficulty in preparing spherical pellets of uniform size, weight, density, and porosity for experimental purposes, pellets of a cylindrical shape were formed in a press.

Jan 1, 1961

By W. H. Emmons

This paper is the second of a series treating the relations of ores of the metals to igneous rocks. In the first paper1 the general problem was outlined and the normal downward changes in metalliferous lodes were briefly stated, with references to earlier papers treating the relations of ores to depths of their formation. The present paper by a number of examples illustrates the relations treated in the first paper. These examples are chosen chiefly from the larger mining districts because their underground developments are more extensive, but the same relations are shown in maps of scores of undeveloped areas in which the main geological conditions are nearly similar. Ecology of Metalliferous Deposits Ore deposits are divided into three groups: 1, Those formed by sedimentary processes; 2, those deposited by meteoric waters; and, 3, those formed in connection with igneous processes. The last group is the most important. It includes the magmatic segregations, which are igneous rocks in the strict sense, and the veins and related deposits, which were formed by precipitation in channels from solutions originating in cooling intrusives. These deposits may be divided into two groups: 1. Those related to intrusives as basic as diorite; and, 2, those related to intrusives more acid than diorite. The second group probably includes more than 95 per cent. of all lode ores. Nearly all of the ores of this group are associated with granitic batholiths or are in positions where it is reasonable to suppose that such a batholith, not yet exposed by erosion, underlies the area containing the deposits. The batholiths are great masses of deep-seated igneous rocks. When they are intruded most of them are probably as basic as diorite and some

Jan 1, 1927

By G. H. Clevenger

Continuing the discussion of the paper of James Johnston, presented at the New York meeting, February, 1914. See Trans., xlviii, 3 to 32 (1914). This paper cannot fail of being of great interest and value to all who are interested in the cyanide process, on account of the important developzn~ents which it records. Mr. Johnston is to be commended for the large amount of detail which he gives, and the company and its management for permitting the publication of data of this character, which while of great value to others could well be considered private property. It might be discussed from a number of standpoints: First, as an example of recent practice in mill and cyanide plant construction; second, the mill practice; third, the cyanide practice; and fourth, the new features in cyanide treatment involved. Perhaps a more vivid way of expressing it would be: First, the equipment or tools with which the various operations are carried on, are they the best and most efficient which could have been selected for their respective uses; and, second, is the best use in every case made of these tools? It may be well inquired is the highest possible recovery of silver made at the lowest cost per ounce recovered? For after all, the making of the greatest ultimate profit is inseparably associated with successful metallurgical practice; there must therefore be at all limes a careful balance maintained between recovery and cost of obtaining it. I wish to call attention in a very general way to the equipment used and to an anticipation of questions which are bound to arise in this connection. However, the bulk of my discussion will be confined to the presentation Of certain additional data, together with a more or less general discussion showing the line of development which leads up to the present practice and the applicability of certain features of it to similar problems elsewhere. There are a number of vital points of broad general interest involved in Nipissing low-grade practice upon which metallurgists will by no means be agreed to which I wish to call particular attention in the hope that it will lead to the presentation by others of data of practice in other districts which will assist in reconciling this divergence of opinion.

Jan 1, 1915

By R. S. Hooper

In attempting to describe recent mining developments at the Bunker Hill mine, it may be well to recall first the old days of hand mining when holes were laboriously drilled by hand to a maximum depth of three feet, and were shot one or two at a time, in order that the miner could take advantage of every slip, crack or bedding plane, and so save as much drilling as possible. Broken muck, of course, was loaded by hand shoveling into wheelbarrows or small cars, and heading advances or stope tonnages were governed by the number of men that could find room to work in any given place. The first big improvement over these old methods was the introduction of the reciprocating type of air-powered rock drill. This innovation, crude as it was, enabled the miners to set up a machine and drill a complete round of holes in one shift; but broken muck was still loaded by hand, and the size and rate of advance in headings were limited by time required to remove the broken rock. The next improvement of consequence was the appearance of the hammer-type rock drill, which greatly increased drilling speed over the reciprocating type, and made possible the completion of a full cycle in one shift, by the use of crossbars in headings, and permitted drilling and mucking to be carried on at the same time. Rock drills continued to improve as time passed, and finally the smaller and more efficient mucking machines appeared on the scene, and it became possible to muck out a round of broken rock and have a clean setup for one or more drill columns and machines. A complete cycle of mucking, drilling, and blasting was completed in one shift with an average advance of five feet. These conditions prevailed for several years, but as the mine grew deeper, the distances to transport the workers grew longer, and this fact together with the shortening of the working day, soon presented the problem of attempting to complete a cycle of operations in a shift of only six hours at the working faces. Anticipating this condition, the operating heads at the Bunker Hill had started an intensive study of more and better mechanization, and over a period of comparatively few years have adopted and placed in service methods and machines that make it possible for a three-man crew to consistently advance headings seven by nine feet in cross section, at the rate of eight feet, and more, per shift, doing all the mucking, switching, drilling and loading. These improvements consist of the following major items: I. The development of a light, flexible, easily transported jumbo equipped with pneumatic columns (Fig I), that has decreased the "setting up" and "tearing down" time an average of 11/2 hr per shift, Or 25 PCt of the available working time. These jumbos were developed at the Bunker Hill mine by members of the staff and consist of two pneumatic columns attached to a suitable carriage. They fold

Jan 1, 1949

By Heihachi Kamura

In this research, the proper temperature for the reduction of iron ores by carbon monoxide was determined. Also, the difference of the rate of reduction on the sizes of ore under four mesh per linear inch was estimated, but no evidence could be found. Rates of reduction on the seven kinds of ore were compared with the results of the experiment, showing a close relation between reducibility and density of ore. Finally, the maximum size of ore that can be reduced in applicable length of time was determined. The author thinks that the process of production of steel may be replaced by low-temperature reduction of iron ores some time in the future. THE reduction of iron oxide, such as Fe203, to iron in the blast furnace is performed principally by carbon monoxide, but partly by solid carbon by the two following reactions: Fe203 + 3CO = 2Fe + 3CO2 2Fe203 + 3C = 4Fe + 3CO2 It is known that reduction by carbon monoxide takes place at a much lower temperature than reduction by carbon and that the reducing action of carbon monoxide progresses to the inside of the ore in lump form by gaseous diffusion. In the reduction by carbon, however, the reducing action takes place only at the contact surface of the ore and carbon, so that the more complete the reduction by carbon monoxide, the more efficient is the operation. However, the reduction does not progress as shown in the foregoing formula, because carbon dioxide acts oxidizingly on the metallic iron to such a degree that when the gaseous composition reaches a certain proportion of carbon dioxide to carbon monoxide, the reduction practically stops, even though the gases are moving slowly through the heated ore. The proportions of carbon monoxide and carbon dioxide in the gas depend on the kind of iron oxide and the temperature of reduction, also the duration of time in the reaction. The longer the time of the reaction, the higher the proportion of carbon dioxide obtained in the gas, but finally it will attain to a condition of equilibrium.

Jan 1, 1925

THE decades immediately before and after the end of the nineteenth century (1890-1910) were a period of increased activity in mineral industry education. One reason for this, undoubtedly, was the rapid increase in mineral production in the decade 1880-1890; pig iron and copper production tripled; coal, lead, and zinc output more than doubled. Most of the other mineral substances followed the same general trend. Aluminum production began in 1886; petroleum output, which in 1888 was less than it was in 1882, almost doubled in the next three years. Gold alone showed no appreciable change until its discovery at Cripple Creek in 1891, followed by the Klondike in 1896, brought to boiling a public interest in minerals that had been simmering for some years previously. The first cyanide plant in the United States was erected at Bodie in 1892, and the first chlorination plant at Cripple Creek* the next year. Silver- lead smelting had already greatly developed, and the metallurgy of copper was almost transformed. The hearth area and smelting capacity of copper reverberatory furnaces more than quadrupled between 1878 and 1894; matte converters were first erected at Butte in 1884. Copper production of the United States in 1899 was 20 times that of 1872. While it was the increased technology used in mineral production that really made the field attractive for educated young men, undoubtedly they did not realize that, and were impressed mainly by the quantitative increase in output. Another factor was the increased general interest in engineering education; three times as many men took engineering degrees in the United States in 1890 as in 1880; 1892 showed almost a 56 per cent increase over 1890. Industry had come to recognize that technical training was worth while. The mineral industry lagged somewhat at first; the total number of mining degrees

Jan 1, 1941

By D. R. Mash

A strong yield point with attendant enhanced mechanical properties was found in commercially pure beryllium under certain conditions of heat treatment. Beryllium specimens also responded to both quench and strain aging treatments. Based on these results, a possible means of obtaining increased normal temperature mechanical properties is suggested. COMMERCIALLY pure beryllium has been found to exhibit the yield point phenomenon and several other aging manifestations under certain conditions of heat treatment. This behavior is not surprising in view of the present accumulation of experience regarding such effects in numerous metals; but in addition to extending this experience to include beryllium, the present study is of interest because aging effects are generally associated with the presence of small amounts of solute elements. The well known lack of tensile ductility in beryllium at normal temperatures is also considered to be due to impurities in some way. In the present investigation, the view was taken that beryllium of commercial purity (greater than 98 pct) should be considered as a dilute alloy and that precipitation phenomena may well exist which could lead to enhanced mechanical properties. In connection with this possibility, published data on the variation of mechanical properties with temperature are of interest. For example, Fig. 1 illustrates the variation of ductility (percentage of elongation) and ultimate strength as a function of temperature for beryllium of various histories.* Although these curves are somewhat schematic in nature, they clearly indicate the possibility that precipitation of an unstable phase and/or aging effects occur during tests in the region 400" to 700°C. The existence of such behavior should be recognized as affecting the properties of the commercial material and perhaps can be employed advantageously. Experimental Method All testing was done at room temperature using a Baldwin universal testing machine. A microformer extensometer was used in conjunction with a micro-former-type stress-strain recorder. All tests were conducted at constant loading rate, the slowest rates being used. This corresponded to 120 lb per min in the 1200 lb full scale range and 300 lb per min in the 6000 lb full scale range. After the rate of loading was set in the elastic range of the material during the early part of the test, no further adjustments were made, allowing the test to proceed at that setting. In the plastic region of the curve above the yield region, strain rates of from 0.002 to 0.006 in. per min were regularly obtained. All experimentation was carried out on specimens machined from the same lot of beryllium, lot No. Y5036BP. Table I shows the chemical analysis as furnished by the supplier, Brush Beryllium Co., as well as the standard specifications to which commercial beryllium is produced. Both 1/4 in. thick hot pressed plate and ½ in. round hot pressed and warm extruded rods were obtained. The history of the material is reported to be as follows: 1—Beryllium metal plates, produced from a standard hot pressed QMV beryllium metal block 4x15x40 in., were cut off and finished machined to 1/4x6x12 in. flat plates. The original hot pressed block was made by hot pressing —200 mesh vacuum cast attri-tioned powder at about 1050°C under vacuum. 2—Beryllium rod was hot pressed and warm extruded. Extrusion billets were machined from the regular hot pressed blocks followed by extrusion at 425°C. The extrusion was done without jacketing, and graphite was used as a lubricant. The rods were then straightened at 720 °C, after which they were annealed at 800°C for 15 min. Both flat tensile specimens and round tensile specimens were tested. The former were machined from the plate stock into standard specimens according to specifications shown in ASTM E8-52T. The nominal cross-section was 0.25x0.500 in. and the gage length was 2 in. The round specimens were

Jan 1, 1956

By Victor O. Homerberg, Dexter N. Shaw

A study of the correlation of the mechanical properties and of the microstructure with the heat treatment of 60-40 brass has been confined, heretofore, to the rolled or extruded material as received from the mannfacturer. The results obtained by Babson and Buhler,' Bengough and Hudson12 Stead and Stedman,3 and Brayton4 have been confined to the treatment of the material as received. No attempt was made to get the material into a given condition and then to work from this basis. To start with a given structure would have the decided advantage of making the work independent of the original condition, hence, to make the results reproduceable. In a previous paper, it was shown, in connection with the study of the transformation that occurs at about 470" C., that if specimens were quenched to produce the beta structure and then reheated, the beta would begin to break down, at approximately 200" C., into a very finely divided alpha. It was predicted that important results might be obtained if test pieces were to be given a similar double heat treatment and then tested for the mechanical properties as well as a study of the microstructure. The material used in the present investigation was a 3/4-in. round bar of extruded muntz metal of the following composition: Copper, 61.05 per cent.; zinc (by difference), 38.90 per cent.; lead, 0.05 per cent.; iron, trace; tin, nil.

Jan 1, 1924

By Joseph B. Perry, G. M. Kirwan

MAGNESITE is found in 22 California counties, but many of the deposits are too small or too impure to be of commercial value. Several of substantial size and quality were entirely exhausted by wartime operation. At present, three properties comprise the only known workable deposits in the state. Of these, the Western mine and the Patterson mine have been known and worked for many years, and have been described in considerable detail in various publications, therefore need only brief mention here, because of their proximity to the Bald Eagle mine. The latter, recently developed, is unusual in type of ore deposit, plant design and operation, as well as products made, and very little has been written concerning it. WESTERN MINE The Western mine, 32 miles south of Livermore, Calif., was formerly operated by C. S. Maltby. It has been a consistent producer for many years.1 The ore is of amorphous variety, occurring along fracture zones in serpentine. The veins vary greatly in width, the average being perhaps 8 ft., with the maximum indicated in one early stope of 40 ft.; 2 ft. is considered the minimum for economical mining. The strike of the veins is predominantly north and south, with dip to the west varying from 40º to 75 º. Walls are well defined and as a rule firm and easily supported. Veins range in length from a few hundred feet to 1000 or more. Their maximum vertical extent is about 350 ft., but many run less. Early mining consisted of open-cut and glory-hole work on the larger outcrops. This was followed underground by a modified shrinkage system, the waste and low-grade horses being removed by hand sorting on the tramming levels and transported to surface dumps. Filled-stope mining is used now, in order to eliminate the handling of waste, which has

Jan 1, 1938

By H. T. Clark, S. Feigenbaum

The importance of measuring the temperature of molten steel in the open-hearth furnace has been recognized for many years. Poor temperature control may be costly to steelmaking operations and lead to a lowered quality of the steel. Low or excessive temperatures may shorten the life of the furnace, ladles and molds. Rates of reactions in the furnace and efficiencies of deoxidizers are known to change materially with a change in the temperature of the metal and slag. Ladle skulls and mold and stool stickers cause steel to be scrapped instead of being converted into useful products. Finally, the structure, segregation and surface condition of ingots are affected by the teeming temperature. Mill investigations of the effect of bath temperature upon steelmaking operations have been largely qualitative in character, based upon observations by practical melting men. The physical chemist has used the empirical information available and has reached reasonable and useful conclusions with respect to the various melting processes. The introduction of a reliable direct-reading pyrometer will permit accurate quantitative evaluation of the effects of temperature and should furnish a more rational basis for study of the thermochemistry of steelmaking. The problem is not merely one of making a small numbcr of temperature measurements in the open-hearth furnace. This has been done by several methods to a * Assistant Manager, Research and Development, Jones and Laughlin Steel Corporation, Pittsburgh, Pennsylvania. Issued as T.P. 2031 in MEtals Technology, June 1946; also in Open Hearth Proc., 1946. † Open-hearth Metallurgist, Jones and 1aughlin Steel Corporation, Aliquippa. Pennsylvania. degree of precision that was apparently satisfactory. Considerable effort by a number of investigators has been directed rather to the development of an open-hearth bath pyrometer that would be both accurate and practical for routine measurements. To be practical, the pyrometer should be inexpensive to operate; that is, the installation, operating and maintenance costs should be exceeded by the tangible benefits to the open-hearth operator. Temperatures from 2800' to 3100°F. are. encountered in the open-hearth furnace. The surface of the molten metal is covered by several inches of slag, which prevents direct observation of the metal surface for optical or radiation measurements. Both slag and metal are highly reactive at these temperatures and will attack to a greater or lesser extent any material immersed in them. Adequate protectioil of thermocouples, which of necessity must be brought to the temperature of the bath, has generally resulted in a large, heavy assembly made up of brittle materials, unsuited for handling on the open-hearth floor. The life of the equipment was short and maintenance was an important consideration. Earlier Work Any of a number of Physical Properties of liquid steel could conceivably be used a a basis for temperature measurement. Efforts to the present time, however, have been confined largely to measuring either the thermal electromotive force generated between two dissimilar materials immersed in the steel or the intensity of radiation from the surface of the steel. These

Jan 1, 1947

By P. G. Carpenter, R. G. Nisle, F. W. Bubb

It is the purpose of this paper to describe an electrical computer which has been constructed to solve the equations for vapor-liquid equilibrium in multi-component systems. The instrument consists of seven component-computing units each with proper indicating means and power supplies. Each unit is a resistance network with a voltage matching servomechanism, and each provides an output voltage proportional to the mol-fractions for vapor and liquid phases. These voltages are summed and matched with a reference voltage to provide the solutions. Any reasonable number of such units may be put together to make a computer. The theory and operation of the computer is discussed. A number of applications and examples of computer results are given. The computer yields the over-all vapor or liquid fraction to a probable error of 0.002. An interpolation method is described which reduces the probable error to 0.0002. INTRODUCTION The process known as Flash Vaporization may be described as follows: A mixture of known composition of relatively volatile components is allowed to come to thermodynamic equilibrium at some given temperature and pressure by any path whatsoever. In general, a vapor and a liquid phase will be present at equilbrium. The problem is to determine the fractions of the mixture in the vapor and liquid phases, and to determine the mol fractions of the various components in each phase. The relations that exist between these various quantities at equilibrium are well known and will be given later. These equations are difficult to solve, yielding only to trial-and-error methods. The virtues of the analog computer are its speed and the automatic character of its calculations. The device is operated by turning a crank which varies the value of v, the total vapor fraction. This actuates a number of servomechanisms which perform automatically all computations. This computer facilitates the solution of such problems as (to mention a few] : Analysis of separator operation, studies of changes in composition of reservoir fluids with pressure decline, and analysis of natural gasoline plant operation. Examples of some of these problems are given in detail later. STATEMENT OF THE PROBLEM The essential equations are xm = 1+(km-l)v . . (1) Kmzm ym =------------------------. . (2) 1 + (Km-l)v ; n n S S xm= --------------------=1 1 + (Km-l)v m = 1 m=1 ......(3) n n S = S Km Zm =1 S ym 1 + (Km-1)v m=1 m = l ......(4) where ym = Vm/V = Mol fraction of m-th component in vapor phase. xm = Lm/L = Mol fraction of m-th component in liquid phase. Zm = Fm/F = Mol fraction of m-th component in mixture. KM = ym/xm = Equilibrium constant for m-th component at the given temperature and pressure. v = V/F = Mol fraction of vapor in the mixture. F = Total mols of a mixture of n components. V - Total mols of vapor in the mixture. L = Total mols of liquid in the mixture. Fm = Total mols of m-th component. Lm = Mols of m-th component in liquid phase. Vm = Mols of m-th component in vapor phase. Assuming the total mols of the mixture F and its composition (all the Fm) to be known — either from a quantitative analysis or from the amounts put together to make the mixture — the zm = Fm/F may be regarded as known quantities. From the given temperature and pressure of the mixture the K., are known (principally from experimental data). The primary problem is then: having given all the zm and Km to calculate v and all the fractions xm and ym. Having calculated these ratios, it is a simple matter to calculate V. L. Vm, Lm from their defining equations. SOLUTION OF THE PROBLEM Basic Computer Unit The computer consists of n units, each of which provides voltages xEo and YE, proportional to x and y as in

Jan 1, 1950

By H. T. Clark, S. Feigenbaum

The importance of measuring the temperature of molten steel in the open-hearth furnace has been recognized for many years. Poor temperature control may be costly to steelmaking operations and lead to a lowered quality of the steel. Low or excessive temperatures may shorten the life of the furnace, ladles and molds. Rates of reactions in the furnace and efficiencies of deoxidizers are known to change materially with a change in the temperature of the metal and slag. Ladle skulls and mold and stool stickers cause steel to be scrapped instead of being converted into useful products. Finally, the structure, segregation and surface condition of ingots are affected by the teeming temperature. Mill investigations of the effect of bath temperature upon steelmaking operations have been largely qualitative in character, based upon observations by practical melting men. The physical chemist has used the empirical information available and has reached reasonable and useful conclusions with respect to the various melting processes. The introduction of a reliable direct-reading pyrometer will permit accurate quantitative evaluation of the effects of temperature and should furnish a more rational basis for study of the thermochemistry of steelmaking. The problem is not merely one of making a small numbcr of temperature measurements in the open-hearth furnace. This has been done by several methods to a * Assistant Manager, Research and Development, Jones and Laughlin Steel Corporation, Pittsburgh, Pennsylvania. Issued as T.P. 2031 in MEtals Technology, June 1946; also in Open Hearth Proc., 1946. † Open-hearth Metallurgist, Jones and 1aughlin Steel Corporation, Aliquippa. Pennsylvania. degree of precision that was apparently satisfactory. Considerable effort by a number of investigators has been directed rather to the development of an open-hearth bath pyrometer that would be both accurate and practical for routine measurements. To be practical, the pyrometer should be inexpensive to operate; that is, the installation, operating and maintenance costs should be exceeded by the tangible benefits to the open-hearth operator. Temperatures from 2800' to 3100°F. are. encountered in the open-hearth furnace. The surface of the molten metal is covered by several inches of slag, which prevents direct observation of the metal surface for optical or radiation measurements. Both slag and metal are highly reactive at these temperatures and will attack to a greater or lesser extent any material immersed in them. Adequate protectioil of thermocouples, which of necessity must be brought to the temperature of the bath, has generally resulted in a large, heavy assembly made up of brittle materials, unsuited for handling on the open-hearth floor. The life of the equipment was short and maintenance was an important consideration. Earlier Work Any of a number of Physical Properties of liquid steel could conceivably be used a a basis for temperature measurement. Efforts to the present time, however, have been confined largely to measuring either the thermal electromotive force generated between two dissimilar materials immersed in the steel or the intensity of radiation from the surface of the steel. These

Jan 1, 1947

By Paul M. Tyler

The term "milling" as applied to nonmetallic minerals often refers merely to pulverizing without preliminary beneficiation. As applied to dimension stone, it embraces all the gteps involved in shaping and giving the desired finish to blocks. Processes such as sawing, planing, rubbing and polishing seem far removed from milling as the term is used in ore dressing, nevertheless they involve the element of concentration, for only 25 to 50 per cent of the gross quarry output may leave the mill as finished products after imperfect stone has been culled and the rough blocks trimmed. On the other hand, numerous nonmetallic minerals have to be concentrated in much the same manner as low-grade ores. Engineers and machinery manufacturers have begun to recognize more clearly the opportunities awaiting them in the nonmetallic field and have brought with them the methods and equipment developed in metal-mining camps, occasionally with little modification. General Economic Considerations Approximately one-half of the total value of the mineral production of the United States represents mineral fuels, and the other half is about equally divided between metals and nonmetals, the nonmetals recently having become relatively more important. In terms of volume the domestic output of nonmetallic minerals other than fuels is more than 10 times the annual output of metals. Considered on the basis of industrial utility and general commercial and military significance, moreover, the flow of nonmetallic mineral products is quite as needful to our national integrity and well-being as is that of metals, fuels, or other basic materials. Despite their importance individually and as a group, the nonmetallic mineral industries differ so widely in essential characters and economic environment that producers thereof have been slow to develop a community of interest among themselves or with the metal-mining fraternity. A spirit of change is in the air, rule-of-thumb methods soon may be relegated to limbo, and new methods—especially time-tested ideas borrowed from ore-dressing practice—are being introduced. A faithful record of plant practice in certain of these fields, however, must register

Jan 1, 1935

By M. C. Udy, C. H. Lorig

THROUGH the years much interest has been centered in attempting to develop a direct method of iron-ore reduction, to replace or supplement the present indirect blast-furnace process. It would not be difficult to produce a list of more than 500 patents dealing with the direct production of iron and steel, but the few of this type of process that have proved successful do not produce in competition with the blast furnace; they produce special products. A survey of the literature reveals that the equilibrium conditions for the reduction reactions (iron oxides with carbon monoxide and with hydrogen) have been fairly well established but that data on the rate of reaction are discordant, although the general effects of the variables are known. This dissertation deals with the rate of reduction of a magnetite concentrate with hydrogen. The following variables have been studied: bed depth, gas velocity, particle size and temperature. The behavior of a single particle was also studied. LITERATURE Two general factors should he considered in a study of reduction of iron oxide: (1) equilibrium relations, and (2) rate of reaction. The first factor, equilibrium, has received the attention of many investigators and the equilibria Fe3O4-FeO-H2-H2O, Fe304-FeO-CO-CO2, FeO-Fe-H2-H2O, FeO-Fe-CO-CO2 are fairly well established. Of the second factor, the rate of reaction, much less is known. Data are comparatively scarce and there is very little concordance. The discordance probably results from the large number of variables influencing the reactions. However, the general effect of the variables is known. Among these variables are temperature, gas velocity, particle size, porosity, gas composition (distance from equilibrium), presence of impurities, greater or less prevalence of side reactions, and even design of the apparatus itself. Wetherill and Furnas1 published an excellent paper in 1934. They point out that any one or more of five processes (the chemical reaction, diffusion of the reactant through the gas film, diffusion of the reactant through the solid phase, diffusion of the reaction product through the solid phase, or diffusion of the reaction product through the gas film) may be the slow process, and thus the rate-controlling process. It is regretted that the work of these authors was limited to experiments at one temperature, and that the range of gas compositions was limited. Langmuir2 has shown that heterogeneous reactions take place at phase boundaries.

Jan 1, 1942

By John L. Miles

John L. Miles (Arthur D. Little, 1nc.)—Pollack and orris" have reported measurements on electron tunneling through A1-A12O3-A1 sandwiches in which the oxide was formed by gaseous oxidation in a glow discharge. From these measurements they deduced the asymmetry of the barrier and, since this is small, conclude that the mechanism suggested by Mott19 for the growth of oxide in thin A12O3 films is inapplicable. In earlier papers20 Pollack and Morris report similar work for oxide films grown thermally. In this case they find a greater asymmetry and conclude that the Mott mechanism is valid. I would like to point out that both these conclusions are quite unjustified. Mott suggests that the growth of the oxide film on aluminum results from the passage of ions through the already present film of oxide under the action of an electric field. This field results from a constant voltage which is in effect a contact potential between metal on one side of the barrier and adsorbed oxygen ions on the other side of the barrier. The theory does not require that the oxide grown is nonuniform either in stoichiometry or structure. It does however specifically assume that the partial layer of ionized oxygen on the surface remains adsorbed on the surface of the growing oxide. In other words, the so-called "built-in field" remains in the oxide only as long as the ionized oxygen is present. When a counter electrode of aluminum is deposited on the oxide, it will react with the adsorbed oxygen on the surface of the oxide, thus forming a small additional amount of oxide. It is clear, then, that there is no requirement in the Mott theory of oxide growth which would necessitate tunneling currents through an Al-A1203-A1 sample to be different when the polarity is reversed. Neither does the theory eliminate the possibility that some additional mechanism could cause the tunneling barrier to be asymmetric and hence tunneling currents to be a function of polarity in such a sandwich. Thus these tunneling-currents measurements are not germane to the question of whether the Mott mechanism is the true method of growth of aluminum oxide films. In fact, it is not surprising that there should be a difference between the oxide properties at the two interfaces (with resulting asymmetry in the tunneling barrier) since the growth conditions and growth rates must have been quite different at these two positions. S. R. Pollack and C. E. Morris (authors' reply)— The point raised by Miles above is one has caused some confusion in the past. The following is an attempt to clarify this point. The built-in field which is responsible for the growth of the thermal oxide at low temperatures arises, according to Mott, because of the passage of electrons from the Fermi surface of the oxidizing metal to surface states introduced by the adsorbed oxygen. It is assumed that the energy of these surface states lies below the Fermi energy of the metal. Electrons therefore continue to flow from the metal to the surface until the built-in electric field raises the potential energy of the surface states to the value of the Fermi energy in the metal, at which time equilibrium is obtained between the surface states and the metal. That is in equilibrium as many excess electrons pass from the metal to the surface per unit time as vice versa. The surface of the oxide prior to deposition of a metallic counterelectrode can then be pictured as follows. The Fermi energy lies in the energy gap of the oxide and is essentially pinned at the energy of the oxygen surface states. The vacuum work function of the oxide is then given by the sum of the electron affinity of the oxide (i.e., the difference in energy between the vacuum and the conduction-band minimum) plus the energy difference between the conduction-band minimum and the Fermi energy. The deposition of a metal onto the surface of the oxide can result in a transfer of electrons across the extremely thin oxide only if there is a contact potential difference between the deposited metal and the parent metal or oxide. That is if the vacuum work function of the deposited metal differs from that of the parent metal, then charge can be redistributed across the oxide in order to equilibriate the Fermi energy across the structure. (It should be

Jan 1, 1965

By C. C. Furnas, T. L. Joseph

It is well known that particles of different sizes are not distributed evenly throughout the average charge in an iron blast furnace. Just how great the disparity in particle size in different parts of a single plane in a furnace may be is indicated by the results of some recent investiga-tion1,2 conducted by the Bureau of Mines on a furnace operating on Lake ores. The wide variations found in gas velocity, gas composition, and temperature from the periphery to the center of the upper charge column were caused by the great variation in particle size of the raw materials used and were also greatly influenced by the methods of charging. This paper summarizes the results of an investigation of the influence of different methods of charging and of the treatment of raw materials upon the size distribution of the solid particles in the blast furnace. A more complete report will appear later as a Bureau of Mines technical paper. Importance of Gas-solid Contact One of the authors has pointed out in a previous report? that the operation of the blast-furnace process is entirely dependent on contact between the gas stream and the solid particles in the stock. The gas stream carries the necessary heat as well as the carbon monoxide molecules that do the work of rednction. In the parts of the furnace in which there is little or no contact between the gas stream and the solids there can be little work of reduction. Obviously, the part of the apparatus that is not doing the work for which it is intended is inefficient; the ideal condition is one in which all portions of the stock column are

Jan 1, 1929

By Robert Goodrich

EXPERIMENTS ON A PORPHYRY COPPER ORE FROM BISBEE, ARIZ. THIS research was done partly in the non-ferrous laboratory of the Department of Metallurgy of Columbia University, under the direction of Dr. Edward F. Kern, and completed elsewhere. Acknowledgment is due to Prof. Arthur L. Walker, Dr. Edward F. Kern and Dr. William Campbell of the Department of Metallurgy, for their kind advice and for the inspiration derived from their instruction. This report is given under the following heads: Petrographic Description (Microscopic Study); Sampling and Preparing Ore for Treatment; Chemical Analysis; Treatment of Ore. PETROGRAPHIC DESCRIPTION Texture: Variable. Fine to medium mixed aggregate. Original structure: Obscure. Secondary structure: Fractured; healed.

Jan 8, 1915