Search Documents

By Geraldo Lúcio de Faria

Os aços IF são livres de elementos intersticiais, como o C e o N, na matriz ferrítica. Estes elementos são controlados no processo de refino na aciaria, a partir da aplicação de técnicas de desgaseificação a vácuo, juntamente com a adição de elementos estabilizantes, como Ti e Nb. Durante a fabricação e em algumas aplicações dos aços IF, como por exemplo soldagem, a transformação de fase austenita?ferrita e o efeito dos elementos de liga na sua cinética têm forte influência na microestrutura final.Neste contexto, este trabalho caracterizou microestruturalmente e comparou as cinéticas de transformação de fase de dois tipos de aços IF com composições químicas diferentes, sendo eles o IF-Ti e o IF-TiNb. Por meio dos resultados obtidos, foi possível concluir que o aço IF-TiNb, como fabricado, possui uma microestrutura mais refinada devido à presença do Nb e seu papel na laminação controlada do aço. Além disso, observou-se que as temperaturas críticas Ar3 e Ar1 do aço IF-TiNb são sistematicamente menores do que as temperaturas medidas para o aço IF-Ti. Como a fração dos elementos microligantes em solução sólida é muito pequena, atribui-se este efeito à diferença no teor de Mn dos aços estudados, que parece potencializar o refino de grão na etapa final de resfriamento da chapa de aço laminada.

Oct 30, 2017

By Flávia Tereza dos Santos Fernandes Tolomelli

Este trabalho teve como objetivo estimar as temperaturas de transformação de fases por meio de termodinâmica computacional (A1 e A3), dilatometria (Ac1 e Ac3) e monitoramento do resfriamento ao ar após passes de laminação a quente em escala piloto (Ar3 e Ar1). Objetiva ainda descrever a evolução microestrutural da austenita em um aço baixo C microligado ao Nb onde se almeja a produção de um aço ferrítico-bainítico, coletando-se amostras após cada passe de laminação através do congelamento da microestrutura por intermédio de resfriamento em salmoura com o objetivo adicional de verificar a ocorrência de recristalização entre passes.

Jul 30, 2018

By Xiaowei Du, Xitao Wang, Xuekun Shang

The deformation behaviors under both tensile and compressive forces and microstructure evolutions of cast SA508-4N steel were investigated at elevated temperatures. True stress-strain data were obtained from hot deformation experiments performed on a Gleeble-3500 thermal-simulator under different temperatures (750-1200C) and strain rates (0.001-10 s-1). The reduction of area decreases as a function of temperature from 750C to 900C and then increases. At 1200C, the reduction of area reaches more than 99% with the strain rates of 0.5 s-1 and 1.0 s-1. The dynamic recrystallization under compressive stress occurs at 800C under low strain rate and a complete dynamic recrystallization can be observed when the temperature reaches above 1100C. A “two-stage” flow stress constitutive model concerned with dynamic recovery and dynamic recrystallization was established based on the true stress-strain data. This model shows good agreement with experiment results. Moreover, we developed a dynamic recrystallized grain size model to describe the average grain size after complete dynamic recrystallization.

Oct 1, 2019

By Bruna Iost Camacho

Inclusões não metálicas são impurezas presentes nos aços que corrompem, quando não moderadas, suas propriedades mecânicas e metalúrgicas. O tratamento de inclusões com ligas à base de cálcio é fortemente utilizado visando à produção de aços mais limpos e é fortemente induzido pela composição química e temperatura do aço. O objetivo geral deste trabalho será o estudo termodinâmico e experimental a respeito da modificação de inclusões não metálicas através do tratamento com cálcio, em aços de diferentes teores de enxofre. O presente trabalho utilizará como metodologia: i) obtenção de dados através de experimentos em forno resistivo para determinar os dados iniciais utilizados nas simulações; ii) estudo termodinâmico computacional através do software FactSage; iii) análise de inclusões via MEV/EDS e ASPEX-PSEM explorer. iv) comparação dos resultados obtidos nos dois meios de análise e também compará-las com os resultados obtidos via simulação. Para tanto, serão estabelecidas dife rentes temperaturas e concentrações de cálcio no banho e diferentes tempos de processo. Como resultado final, espera-se gerar um maior conhecimento que contribua para a compreensão dos fenômenos envolvidos em aços com maior teor de enxofre. Além disso, espera-se validar as técnicas e metodologia empregadas neste trabalho.

Aug 8, 2018

By Henrique Lacerda Eleutério, Aldo Henrique de Almeida Barbosa, Vicente Tadeu Lopes Buono

The automotive industry’s interest in galvannealed (GA) boron steel for hot forming processes application has been steadily increasing due to its excellent surface quality, galvanic protection provided to the parts, good paint adhesion and better weldability in relation to other coatings for this application. In this study, samples of 22MnB5 galvannealed steel were heat treated and hot stamped on a water cooled die in laboratory scale. The influence of heat treatment on stability of coating and steel was assessed by using initial heating rates 11.0ºC/s and 15.0ºC/s. Microstructural evolution of galvannealed coating and structural integrity of steel during hot forming were investigated by scanning electron microscopy with energy dispersive spectroscopy analysis (SEM/EDS/Line scan), X-ray diffraction (XRD) and optical microscopy (OM). It was possible to quantify the Fe-Zn phase evolution during hot forming, to understand the effect of these heating rates on the product properties and to establish an optimized heat treatment for hot forming of these steel. The heat treatment with the heating rate of 15.0ºC/s presented greater operational flexibility and final products free from surface defects or cracks in the substrate.

Oct 1, 2019

By Hui-bin Wu, Rui Yuan, Yang Gu, Peng-cheng Zhang, Zheng-zhi Zhao

The corrosion behavior of three kinds of medium-Cr rolled steel pipeline steels in carbon dioxide collecting and transporting environment at different temperatures was studied. The results shew that the 5Cr sample was most affected by temperature. When the temperature rised from 30 °C to 90 °C, the corrosion rate increased from 0.12 mm/a to 1.87 mm/a, which was increased 15.6 times. The corrosion rate of 7Cr steel at 30 °C was similar to that of 5Cr steel. However, as the temperature increased, the corrosion rate rised slowly, increasing by 2.4 times at 90 °C. The corrosion rate of 9Cr steel was not obvious with temperature, and it was always below 0.06 mm/a. The thickness of the corrosion product film of the three samples gradually increased below 70 °C, and suddenly increased above 70 °C. This was related to the negative temperature coefficient of the solubility of FeCO3, and the thickening of the product film also affected the ion exchange of the cathodic reaction. An increase in the Cr content contributed to grain refinement and increased the proportion of the small-angle grain boundaries. More fine grains mean an increase in the total length of the grain boundaries, which could provide a diffusion channel for the free Cr element; on the other hand, the low-angle grain boundary structure was more orderly, with a lower free volume and lower interface energy. Under the combined effect of both, 9Cr steel and 7Cr steel had high volta potential and better corrosion

Oct 1, 2019

By Eric Schaub

Hot Blast Stove Systems are an important equipment of a Blast Furnace plant. During the last years, performance requirements and operation practice for the Hot Blast Systems have changed and have a big influence on the Blast Furnace operation. Therefore it is necessary to keep the Hot Blast System in proper condition in order to maintain the production capacity of the Blast Furnace. It is important for operators to know the condition and relevant constrains of a Hot Blast Stove Plant. Assessing its condition on a regular basis, especially in advance of a Blast Furnace relining is therefore advisable. Considering the individual condition of the Hot Blast Stove Plant, improvements in operation, but also specific and dedicated repairs might be implemented. Design improvements can be implemented as well during such repairs. This paper will describe some of these design improvements, will illustrate their implementation in new hot blast stoves but will also describe repair methods for existing stoves. In addition new developments became popular during the last decade, like the so called Dome Combustion Stoves, which was invented already 30 years ago in Western Europe. Paul Wurth’s development in this regard will be discussed in this paper as well.

Oct 30, 2017

By Dyego Monteiro de Souza

This study compares the wear resistance of specimens lubricated with biofluids or mineral oil. Tribological studies were performed by ball-cratering test. In these tests were used as lubricants epoxidized soybean oil, castor oil and mineral oil. The specimens used were untreated and nitrided AISI 4140, while a steel ball AISI 52100 was used as a counterbody. In order to analyze the results obtained, the worn volume was calculated and the characterization of the crater, after the test, was made using optical microscopy and SEM. Wettability was also measured for the different surface condition and lubricants. As expected both specimens showed a smaller volume worn when lubricated with mineral oil due to inherent properties of this type of lubricant. Among the vegetable oils studied, the castor oil showed a better performance in the lubrication of the specimens untreated while on the nitrided specimen have shown less wear when lubricated with epoxidized soybean oil, indicating a difference in the efficiency of oils, as lubricants, depending on the surface conditions of the mechanical components.

Jul 31, 2018

By Afonso Cardoso da Silva, Romeu Thomaz Viana Jr, Emanuelle Garcia Reis, José Herbert Dolabela da Silveira

The Gerdau Ouro Branco Mill, three years after the implementation of its new plate mill, has started to develop high complexity products. The plate mill’s learning curve has been increasingly challenging since products are being developed to their highest grades. This work aims to present the first results of the development of steels of the strength class of 510 MPa produced by TMCP (Thermomechanical Controlled Processing) followed by accelerated cooling. These results show the potential and advantage of the accelerated cooling process regarding to obtain products of high mechanical strength and high toughness, associated with a low equivalent carbon.

Oct 1, 2019

By Christian Overhagen

In bar and wire rod mills, rolling procedures featuring three- and four-roll technologies are state-of-the-art to produce high-quality long products. While a rolling model for the three-roll process including an equivalent pass method was already presented by the author, pass design methods are dealt with in the current work. The geometry of the rolled product and roll grooves are described mathematically using functional contours, allowing geometric-numerical methods to be used for manipulation and deformation simulation of the rolled product. For a given pass, the output section is constructed using these methods. Roll force, torque and rolling power are calculated using the mathematical rolling model presented before. Interstand tensions are discussed as influencing parameters on the force, torque and power demands, as well as on the section shape. A mathematical model for the influence of interstand tensions on lateral spread is incorporated in the model. To complete the pass design model, elastic mill stand feedback is considered in terms of a fixed elastic modulus for each rolling stand, the elastic feedback and therefore cross-sectional variation due to elastic mill spring being calculated iteratively from the roll force by application of the Gagemeter equation. The interaction of section height and width faults due to elastic mill spring and spread variations is analyzed in detail and the consequences for the roll pass design are shown.

Oct 1, 2019

By Zou Zhongpping

Under the new normal state, blast furnace outputneeds to be adapted to the market demand, however the limitation in blast furnace output has significant impact on blast furnace operation and is prone to cause inactive furnace hearth and higher fuel ratio. To address such problems, some practices to maintain stable and smooth operation of blast furnace in case of output limitation are proposed based on data analysis philosophy, which allows the blast flow and hence the top pressure to be determined based on the hot metal output, and adequate kinetic energy of blast supply can be assured by adjusting the tuyeres. Matching between the oxygen enrichment and the pulverized coal injection is also proposed based on theoretical flametemperature, and burden distribution cycle calculation method is proposed, whichoffersnew approach for analyzing the change in burden distribution pattern.

Oct 30, 2017

By ArcelorMittal Tubarão - Aços Planos

Fatos Relevantes - Produção anual de 4.491.854 t de aço bruto - produção estável em relação à 2012. - Produção anual de Bobinas Laminadas a Quente de 3.726.871 t - 7,8% de elevação em relação a 2012. - Unidades Geradoras da Central Termelétrica em manutenção aproveitando período de menor produção relacionado à parada do Alto Forno 3. - Redução relevante na geração de energia elétrica interna devido menor disponibilidade de combustíveis (off-gas) e redução de produção na Sol Coqueria adequando à demanda de coque do grupo ArcelorMittal Brasil.

Jul 31, 2018

By Adriano Alex de Almeida

Dois aços de grão não orientado com 2,45 e 3,3 %Si com 7 amostras para cada liga, foram estudados para compreensão do efeito do teor de silício nas perdas histeréticas. As amostras foram recozidas com diferentes temperaturas de recozimento final, resultando em diferentes tamanhos de grão. As perdas histeréticas e B50 foram medidos. Os resultados de B50 mostraram que não houve variação de textura entre as ligas com diferentes %Si. Por fim, os resultados não mostraram variações da energia dissipada pela perda histerética com adição de %Si.

Aug 7, 2018

By João Paulo Ferreira Santos

Neste trabalho, foram obtidas estruturas compósitas constituídas por camadas alternadas de epóxi com mantas de nanofibras de nylon 6. As nanofibras foram produzidas pela técnica de eletrofiação. O comportamento mecânico destas estruturas sob tração e sob impacto pendular IZOD foram estudados. A incorporação das nanofibras na matriz epoxídica permitiu aumentos no módulo de elasticidade (6%), na resistência a tração (7%) e na energia de impacto (2%), ou seja, houveram ganhos de resistência mecânica sem sacrificar a resistência ao impacto, ao contrário do que ocorre na quase totalidade dos micro ou macromateriais modificadores do epóxi.

Aug 8, 2018

By Emanuelle Garcia Reis, Gustavo de Sousa, Rodney Pardo Alves

Gerdau Ouro Branco´s plate mill started the operation in 2016 with high level technology. In general, national and international plate markets are every day more rigorous about final product quality. Suppliers must be aware about dimensional accuracy, surface quality and flatness of the plates, independent of the quality standards. To guarantee the best service to this increasingly demanding and competitive market, it is extremely important to guarantee the original project conditions executing the right maintenance of the rolling mill main components. In order to maintain the product quality and avoid the production and maintenance cost increase, it is important to find ways to control the mill and the main process variables, through daily measurements of the equipment performance. This paper aims to present the influence of the main equipment variables that affect the mill operational stability and how to control and evaluate the mill performance.

Oct 1, 2019

By Jose M. Rodriguez-Ibabe, Beatriz Pereda, Beatriz Lopez, Felipe Bastos

The modeling of austenite evolution during the hot rolling of steels is covered in the literature for a wide range of chemical compositions, although mainly for carbon contents below 0.20%. In addition, most research on this topic is oriented for processes that are characteristic of flat products. Compared to those processes, the hot rolling of bars for structural applications presents considerable particularities concerning mainly deformation, rolling speed and rolling temperature profile. Those particularities result in considerable changes on process parameters that affect the austenite microstructure evolution, both in the softening and hardening mechanisms if microalloying elements such as Nb is present. The aim of this work was to develop a model to predict the evolution of austenite microstructure that is suitable for the hot rolling of structural reinforcing bars. Different torsion tests simulating industrial schedules particular from those type of processes were performed. The tests showed the need to investigate Nb strain-induced precipitation interaction with softening mechanisms that can occur during the deformation schedule. At the end, the new proposed kinetics and routines were introduced to a program, MicroSim-Bars®, that is able to model austenite evolution under structural bar hot rolling conditions.

Oct 1, 2019

By Luiz Augusto Ferreira de Campos Viana

O processamento de aços ARBL (Alta Resistência Baixa Liga) para fabricação de bens de capital de dimensões avantajadas pode sobrecarregar máquinas operatrizes de indústrias do setor metal-mecânico. Uma rota alternativa para processamento deste material é a conformação do mesmo a temperaturas elevadas (processamento "a morno"), para redução de seu limite de escoamento e consequente diminuição do esforço nos equipamentos. Entretanto as propriedades mecânicas destes materiais devem ser mantidas após seu retorno à temperatura ambiente. Neste trabalho um aço ARBL temperado e revenido foi submetido a 1, 3, 5, 7 e 9 ciclos térmicos, com a soma do tempo de todos os ciclos térmicos igual a 10 horas e temperatura de 580°C. Em seguida ensaios mecânicos de tração, impacto em corpos de prova Charpy-V e dureza Vickers foram executados. A caracterização microestrutural e análises fratográficas dos corpos de prova de tração e impacto foram realizadas por meio de microscópio eletrônico de varredura (MEV). A análise microestrutural revelou o coalescimento de partículas de cementita em todas as amostras. A resistência mecânica dos corpos de prova submetidos a 1, 3, 7 e 9 ciclos caiu. A energia absorvida no ensaio de impacto aumentou para estas amostras. O corpo de prova submetido a 5 ciclos térmicos apresentou endurecimento secundário. A fratografia de todos os corpos de prova ensaiados a tração revelaram fratura dúctil. O mesmo ocorreu para os corpos de prova submetidos ao ensaio de impacto, exceto para os corpos de prova submetidos a 5 ciclos térmicos. Em nenhum dos casos ocorreu descaracterização do material com quedas nos limites de resistência a valores inferiores aos especificados pelo fabricante.

Aug 16, 2017

By Breno Totti Maia

Para uma boa operação das lanças de oxigênio para convertedores BOF é necessário existir uma boa condição de refrigeração, devido à agressividade existente no ambiente, onde ela fica exposta a condições de alta radiação, gases a alta temperatura e, algumas vezes, com o aço líquido. Para uma boa refrigeração, basicamente são necessários uma boa qualidade de água e condições adequadas de vazão e pressão. Mas somente esses fatores podem não garantir o desempenho adequado às condições de escoamento da água, devido à complexidade geométrica do bico da lança. Esse artigo tem como objetivo apresentar um estudo comparativo de escoamento da água, na parte crítica de uma lança que é o bico, destacando a importância da geometria interna do bico na troca térmica do equipamento. Serão apresentados os resultados comparativos, onde se observa que otimização do escoamento interno no bico da lança aumenta a vida útil do equipamento.

Jul 29, 2018

By Andreas Cestonaro

Roll grade evolution in plate mill applications is traditionally following the development in hot strip mills. New grades normally find their way into service only after being successfully implemented in hot strip production. The majority of the plate mills worldwide are using work roll grades that have been invented before the 1980’s. But today the demands in the mills are pushed by sophisticated product mixes and longer rolling campaigns. The result of this development is a higher wear rate on the work rolls and as a consequence roll hardness is increased and advanced roll materials are used. The backup rolls are also affected by this. The wear rate is higher and the mechanical impact in terms of contact pressure and work hardening is increasing. This paper outlines the results of the roll grade development at Gontermann-Peipers and introduces new materials for work and backup rolls for plate mills.

Jul 30, 2018

By Diogo Tenório dos Santos

This property has been studied to characterize the strength a metallic material exhibits when it is machined so it can be regarded as its typical behaviour. As such, it may even be considered as an intrinsic material property. It is usually measured by an index called Coppini index, which is expressed by the ratio between the removed mass of a cutting tool caused by wear when it is used for machining and its initial one for a certain set of machining parameters. In this investigation, the tests were therefore conducted by an established set of parameters, namely feed rate, cutting and depth rates, in which the same wear mechanism took place in both ferrous alloys: AISI 4140 and AISI 316 steels. They were chosen based upon their increasing ordinary machinability indexes. The initial and final mass of the cutting tool were measured by an analytical scale with 0.01 mg precision. Cylindrical rods of 50-mm diameter were machined and the CI indexes showed a remarkable difference between them: 0.080 for the first steel and 0.049 for the second one, i.e., AISI 316 steel presented better machinability than the first one. It was then possible to conclude that this method presents good results in terms of both reproducibility and adequacy for machine shop conditions and it may be applied in a foreseeable future, mainly for metallic materials that have rather low machinability indices.

Jul 31, 2018