Search Documents

By Chris Larsen, Ian Orford, Mike Cooper

"An autogenous grinding circuit was commissioned at the Brunswick concentrator in October 1998. The autogenous grinding circuit replaced existing surface crushing plants, fine ore storage, rod and primary ball mills. The 8.54m diameter x 4.27m long (EGL) AN1 mill is driven by a bidirectional variable speed 6.3MW ABB wound rotor motor with Slip Energy Recovery (SER) drive. The AG mill was subsequently converted to SAG operation in May 1999 for a number of reasons. The mill is operated in closed circuit with horizontally inclined 660mm diameter cyclones to produce a circuit product P80 of 85 microns. Extensive test work and JKSimMet design modeling resulted in a production circuit operating closely within design expectations.The circuit is highly instrumented and controlled via a hybrid Programmable Logic Controller (PLC-5) and Fisher PROVOX Distributed Control System (DCS) that is in communication with the property information highway. An expert control system (Gensym G2) is used for control of the SAG mill load.Engineering and construction were completed in 28 months from the time of management approval for the project. The Brunswick AG/SAG mill circuit was commissioned on schedule at the $M 23.5 forecast budget."

Jan 1, 2001

By Jian Yang

The mechanism of resulfurization in the desulfurization process with magnesium vapor produced in situ by aluminothermic reduction of magnesium oxide was clarified in the present work. The influences of various operating parameters on the resulfurization were studied and the methods that could prevent resulfurization were proposed. There are two kinds of mechanisms of resulfurization in the desulfurization process with magnesium. One is decomposition of the desulfurization product of MgS under the inert atmosphere. The other is oxidation of MgS under the oxidative atmosphere. Under the present experimental conditions, lowering operating temperature and oxygen partial pressure in the atmosphere could effectively prevent the resulfurization. Adding CaO onto the melt surface was an effective method for preventing the resulfurization due to transformation of the desulfurization product of MgS into the more stable compound of CaS. Since addition of the activated charcoal powders greatly decreased the transfer rate of oxygen in the atmosphere to the melt surface, it also reduced the resulfurization remarkably.

Jan 1, 2006

By Xiaoning Yang, C David Pearson, Brian W. Stump

An experimental study of ground motion from explosions designed to remove overburden in an open pit coal mine is reported. The purpose of this study is a characterization of these ground motions in the distance range of several tens of meters to several kilometers. The investigation has focused upon both single cylindrical sources with different explosive configurations as well as arrays of charges in the production mode. Critical to this study of source configuration and coupling is experimental control of the individual explosions, the timing of the explosions and the geological properties. The height of the explosive charges, their depth and charge distribution were monitored in the field. High speed photography as well as velocity of detonation measurements were made on the multiple explosion source so that detonation of individual charges could be documented.

Jan 1, 1994

By Dominique Vié

Standards methods covers the procedures for testing deep foundation to determine the force and velocity response to an impact of a pile driving hammer or similar device. The results of analysis generally include an assessment of pile integrity and the value of maximum dynamic stresses. But evaluation of static bearing capacity remains a matter of individual engineering judgment. A new 1D finite elements model has been developed for dynamic stresses and velocity analysis. Following an international benchmark of bearing capacity prediction organised by the Belgium Building Research Institute (BBRI), 12 piles in a site of fissured stiff tertiary clay tested in 1999, and 12 piles in a site of dense sand tested in 2001, comparison are proposed between analysis of dynamic tests and static tests results. A procedure is proposed to take in account the results of dynamic test for evaluation of bearing capacity.

Jan 1, 2002

By John Capers

•The IME is the Safety and Security Association of the commercial explosives industry in the United States and Canada. •Founded in 1913 •Board of Governors •5 Standing committees- 1. Technical 2. Environmental Affairs 3. Legal Affairs 4. Safety & Health 5. Transportation & Distribution

Jan 1, 2006

By James C. Fowler

This report contains a description of the contract activities performed by ENSCO, Inc. under contract H0292025. The purpose of this project was to prove the feasibility of detecting hazards in a coal seam using a synthetic pulse radar. This work was conducted in three phases. The first was an analysis of the types of errors which might cause problems. The second was to build a breadboard radar and the third phase was to conduct a field test with the system. The work from each phase is discussed and the results of the field tests are presented. These results show propagation of the radar signal through 200 feet of coal along with reflections from 50 feet away. The final section contains recommendations for future development.

Jan 1, 1981

By H. Robert Ensminger

The Belizean economy registered a modest real growth of 1.3% during 1981. The gross domestic product (GDP), based on current prim was $121 million' with an inflation-rate of 10%. The country received $19 million in economic aid during 1981. In early 1981, Belize'e four commercial banks raised the interest on deposits to 15% in an effort to curb capital outflow. During 1981, the financial situation deteriorated somewhat, particularly the balance of payments. For the year the total value of imports exceeded exports by almost $38 million, while the Government continued to maintain a fairly free trade policy. Import duties and term averaged about 8% on essential item and 40% on nonessential ones.

Jan 1, 1983

Stope back conditions in the cut-and-fill stopes at New Broken Hill Consolidated Limited often deteriorate to such an extent that, because conventional rockbolts are not able to maintain safe working conditions, square-set timber is installed. An attempt to eliminate this costly procedure has involved the use of long grouted rockbolts using high tensile prestressing wire. These bolts were developed in conjunction with the prestressing engineers of BBR (Aust.). This form of support has improved the back conditions, maintained safe working conditions, and delayed the introduction of timber in a number of stopes.Production from these stopes has been maintained at its previous level (at a rate approximately double that of a comparable timber stope).

Jan 1, 1974

By Peeler P. K

The recent renewal of interest in hydrometallurgical routes for copper production has been brought about by the possible future reliance on mixed ores and lower grade deposits, environmental aspects, and energy considerations.A number of hydrometallurgical processes for the recovery of copper have recently been proposed. Flowsheets are developed for two processes which incorporate several treatment methods being experimentally studied in Australia.In the first process a cupric chloride leach is followed by electrowinning whilst the second is based on the formation of cuprous ions, stabuized by acetonitrile and subsequent disproportionation to cupric ions and metallic copper. For the purpose of comparison, flowsheets were also developed for the Arbiter and Cymet processes.Process economics are estimated for the four processes and the results are discussed in relation to competitive pyrometallurgy. None of the four hydrometallurgical processes, with possible exception of the Cymet process, appears to be competitive with established large scale and newly developed pyrometallurgical processes for chalcopyrite.However, because the economics of the individual hydrometallurgical processes depend strongly on specific conditions, a "tailored" process may be competitive with pyrometallurgy in particular circumstances.

Jan 1, 1977

By Louis Schaffer

This report characterizes several coal Dine mobile equipment operator populations with respect to age, mine experience, machine operator experience, and training. The information is used to demonstrate a method of normalizing the injury data collected by the Mining Enforcement and Safety Administration-Health and Safety Analysis Center.

Jan 1, 1977

By W. Dan Hausel

More than 220,000 diamonds have been found in the United States that range from microdiamonds to 40.42 carats in weight (Table 1). Some reports suggest diamonds weighing more than 100 carats have also been found in this country, although these reports have not been verified. The source of most of the diamonds in the United States is a group of kimberlite pipes, dikes and blows in the Colorado-Wyoming State Line district and a group of lamproite pipes in the Murfreesburo, AR area. Other areas where diamonds have been found include the Great Lakes region, the Pacific Coast and the southern Appalachian Mountains. The latter two regions are generally not considered favorable for diamond deposits. This is based on exploration models. They suggest commercial diamond deposits will be restricted to kimberlites emplaced in Archean cratons and to lamproites emplaced in Proterozoic mobile belts accreted to the cratons.

Jan 1, 1995

By Charles W. Huggins

A study of the high magnification of some inorganic fibers which are found in nature or produced in the laboratory, has been conducted with the electron microscope. This series of electron microqraphs shows the important morphological differences exhibited by potassium-lead silicate, lead-aluminum silicate, chrysotile, wollastonite, silicon nitride, potassium titanate, cobalt chrysotile, magnesio-fluor-richterite, fluor-richterite, refractory oxide fiber, silicon carbide, massive serpentine, and palygorskite. A ribbon or a thin lath 250-2500 A. wide is the structural form of potassium-lead silicate and lead-aluminum silicate. Chrysotile, cobalt chrysotile, and massive serpentine all have a tubular structure and a fairly uniform (150-300 A.) diameter. Wollastonite, potassium titanate, fluor-richterite, and magnesio-richterite crystals have a lath shape, and potassium titanate laths are laminated ribbons. Single fibers of silicon nitride and palygorskite are ribbons, and the silicon nitride sample contains many twins (branching fibers). Palyqorskite fibers are highly flexible and have cross-sectional measurements of 150-300 A. Silicon carbide fibers differ from other fibers because their structure consists of several different forms. The sample used in this study had, predominately, a margarite-type structure. The refractory oxide fiber lost, all its apparent fibrosity after being prepared for electron microscopic examination, and only irregular fragments are visible in the electron micrographs.

Jan 1, 1962

The difficulty of accurately sampling cyanide gold bullion for valuation is well known, and nothing new or original is claimed in presenting this paper, but it was thought that a record of differences in the composition of bullion bars found here may be of interest to others, and perhaps helpful to those who have to do with theevaluation of cyanide bullion. This investigation was made after reading Mr. Sydney W. Smith's interesting paper on the Liquidation in Molten Alloys.*A method was in use of boring each ingot in two places and mixing the two borings for the sample. More accurate values were obtained, however, when the bullion was sampled in a molten condition immediately before casting into the ingot; the sample being so taken as to preclude oxidation of base metals before solidification of the sample.In all, samples from 32 ingots were assayed, and comparisons made between the existing boring sample and the proposed dip sample. Assays were also made of two other portions of the borings from each ingot, and the results show that in the majority of cases the borings sample assays higher in gold than the dip sample of the same ingot.The largest ingot cast weighs approximately 920 troy ounces, and has the dimensions shown in the attached sketch (Fig. 1). Ingots are cast in 0.1. moulds i in. thick, smoked and heated.METHOD OF TAKING BORING SAMPLES OF BULLION BARSThe bar is cleaned from adhering slag and drilled in two places only, to a depth of i-in., one hole on the top near one end and the other in the bottom at the opposite end of the bar.

Jan 1, 1931

By R. H. Thompson

Preliminary safe distances for blasting wiring from typical electromagnetic sources are presented. The distances are for underground coal mines and electromagnetic sources in the frequency range below 10 MHz. The distances are based on measurements performed at 3 locations in each of 3 coal mines. The measurement apparatus, measurement procedure, measurement results and the rationale used in the calculation of the safe distances are all described. The safe distances presented are dependent on the measurement results and their interpretation. More measurements are clearly necessary to establish the validity of the suggested distances.

Jan 1, 1985

By Arthur L. Hall

The purpose of this symposium is to challenge industry to better air classification, and as a first step toward fulfillment, to spotlight three fairly recent, aerodynamically designed, highly efficient air classifiers. This discussion does not intend to imply that present practice is bad. Actually, when present air separators are used for the jobs for which they were originally designed, they give high production and uniform operation, with a minimum of maintenance. The customers of nonmetallic mineral pigment producers, however, are making increasing demands for finer products, such as 99.9 pct -20µ, which appears to be beyond the economic capabilities of standard air separators industrially used over the last 10 to 30 years. Here is an actual example. A 10-ft diam pebble mill is in closed circuit with a conventional 12-ft diam centrifugal air separator, grinding 20-mesh wollastonite to a series of fine grades up to 99.97 pct - U.S. No. 325 mesh (44µ). Fig. 1 shows variations in fineness of mill discharge (or air separator feed), recycle for regrinding (or air separator tails), and product as measured by a wet rotating sieve test. For example, when the mill is turning out a product 80 pct -325, the mill discharge or separator feed is 30 pct -325, and the coarse tailings or recycle is only 5 pct -325. Hence 25 pct of the 30 pct available is accepted as product. This is efficient separation, and the ratio of recycle to feed is only about 2: 1. How- ever, to make a product testing 99.97 pct -325 the separator feed is 62 pct -325 and the coarse tailing 60 pct -325. In this case the recycle ratio is about 13: 1 and the economic limit to produce fineness has been substantially reached with this given equipment and process arrangement.

Jan 10, 1957

By R. C. Milici

Historical production data and reserve decline rates can be used both to predict future coal production rates and to estimate when the reserve will be depleted. Reserve estimates inferred herein from historical production data and decline rates are commonly lower than estimates made from geologic data. The latter include significant amounts of lower quality (deeper, thinner, higher sub) coal which may be mined when the better deposits are depleted.

Feb 24, 1997

By Steven Putt

Seismic While Drilling (SWD) is a newly developed technology in the mining industry. Improving upon Measurement While Drilling (MWD) systems, SWD measures mechanical properties of the rock at incremental depths down a blast hole at a much higher resolution. SWD is also immune to common failures and inconsistencies of MWD such as operator and drill specific variation. Seismic While Drilling records the velocity and elastic modulus of the rock with centimeter accuracy in real-time. These properties measured while drilling blastholes are then used as a proxy for density which can be used for: • High resolution geologic modeling • 3D ore control • Drill and blast optimization • Drill to mill tracking One of the distinct challenges with SWD systems is the sheer volume of information acquired. With thousands of measurements per blasthole, the data can be overwhelming for even an experienced engineer. To overcome this complex challenge, the latest cloud computing and analytics models have been simplifying and organizing the data. These newer technologies can amplify an engineer’s capability by delivering actionable insights into their drilling and blasting workflows. The paper presents new results from Datacloud during recent Seismic While Drilling trials in iron ore, metallurgical coal, and hard rock mines around the world. The measurements are compared with wireline geophysical logs, core data, drill cuttings, and conventional measurement while drilling (MWD) systems to validate the technology and show how the data can be used.

By Ernest E. Berger

"INTRODUCTIONOne of the outstanding problems in the normetallic industries, and one which involves two of the greatest of these industries, cement and gypsum, is the reaction of Portland cement with calcium sulphate. To all Portland cement clinker there is added in the manufacturing process, a small amount of retarder, as a necessary ingredient of the finished product. This retards the initial set, increases the strength, and adds to the plasticity of the cement so it will have the desired working and setting qualities. The retarder commonly used is gypsum, (CaSOA.2HO), which is the hydrous form calcium sulphate. Calcium sulphate is also available as plaster of Paris (CaSO4 1/2 HC) and anhydrite (CaSO4). The purpose of this inquiry was to determine the form or mixture of forms best adapted for retarder. The problem is complicated by the fact that cement clinker is a complex mixture of calcium silicates and aluminates, and that clinker from different mills, making cement of approximately equal quality, differs considerably in chemical constitution. Thus the same retarder may give very different results with different types of clinker, especially in the percentage of retarder required for the same degree of retardation.It has been known for some time that a small percentage of plaster of Paris will greatly retard the time of set of Portland cement as well as increase its strength and plasticity, but whether gypsum and anhydrite will have a similar effect is as such disputed question. The offects of gypsum have received little consideration in laboratory research because, even though it will not retard a clinker when the two are mixed in the laboratory, as has been noted in some instances, the cement will have a normal set when the two arc mixed in the large tube mill at the plant, so that practically, gypsum seems to be equally as goou as plaster of Paris, and because of the great saving in cost it has been used almost exclusively."

Sep 1, 1925

By Janice Zinck, Maziar E. Sauber

"To counter the recent uncertainty in the rare earths market, diversify the supply source, and help meet the future demand in this sector Canada initiated development of several new rare earth deposits. In the past few years, a number of various studies on rare earths plant design have taken place mainly covering process development, process selection, and flowsheet design. The purpose of this paper is to provide an overview of known domestic and potential resources and reserves of rare earths and their status quo with a focus on the metallurgical processes using the information available in the public domain. Plant designs currently under consideration in Canada are reviewed and evaluated. An outline of the areas of opportunity for selective innovation and technology development in the rare earths flowsheet development and the associated risks and rewards is provided.INTRODUCTIONThe rare earth elements (REE) have a very small annual market, but they are categorized as very strategic metals vital to global economic growth due to their indispensability to the development of modern defence system, green technologies and electronic applications. The International Union of Applied and Pure Chemistry (IUPAC) defines the REE as the 15 elements on the lanthanide series on periodic table of elements, plus yttrium and scandium. REE are classified as light rare earth elements (LREE; La to Gd), and heavy rare earth elements (HREE; Tb to Lu). Physical properties and chemical reactivity of yttrium is similar to those of HREE, thus it is categorized as such. Properties of scandium are not similar enough to classify it as either a LREE or HREE (Weng et al., 2015; Sappin & Beaudoin, 2015). However, the mining industry does not always abide to this definitive classification of the split between LREE and HREE. Therefore, in a comparative study of projects, there is a need to pay attention to how the elements are classified."

Jan 1, 2016

By Harry W. Campbell

A Bureau of Mines investigation identified no mineral deposits in the Lost Creek RARE II area. Sand and gravel has been mined from alluvial flood plain deposits just outside the RARE II boundary. An oil and gas lease application which includes the eastern portion of the RARE II area is pending. Abundant basalt in the area can be crushed and used as aggregate; but it could not compete with similar deposits in more favorable locations, or with cheaper substitutes such as volcanic cinders or sand and gravel which are available outside the study area closer to major markets. No indication of coal or geothermal energy resources was found. INTRODUCTION Location and Access The Lost Creek RARE II area encompasses 8,300 acres (3,400 ha) of Lassen National Forest in north-central California, about 20 mi (30 km) north of Lassen Peak. The closest city is Redding, California, 50 air mi (80 km) southwest. Peripheral access is provided by State Highway 89 passing near the western RARE II boundary (fig. 1). The Pacific Crest Trail traverses the western margin of Hat Creek Rim adjacent to the eastern boundary of the area.

Jan 1, 1983