Search Documents

By Roger J. Morrell

Bureau of Mines laboratory experiments with reduced scale cutter and cutter forces were performed to (1) define the fundamental relationships governing disk cutter performance and (2) to develop a method of predicting disk cutter performance in soft, medium, and hard rocks. The rock cutting experiments were performed in four igneous and metamorphic rocks that ranged in compressive strength from 38,000 to 67,000 psi. A special testing machine called a linear cutter apparatus (LCA) was used to load and traverse a free rolling disk cutter across a smooth rock surface. Each pass of the disk produced a single crater, and runs were spaced to avoid breakage between craters. During each run the normal and tangential cutter forces were measured and recorded. The soft and medium rock data were obtained from previous Bureau experiments with disk cutters. Crater depth, tangential cutter force, crater volume, specific energy versus normal cutter force, and crater width versus depth are defined within this study. With the use of standard physical properties, performance prediction equations were developed using stepwise linear regression analysis techniques. A method of using these prediction equations to calculate the boring rate, the cutter spacing, and the torque and energy requirements of a full-scale boring machine was also developed.

Jan 1, 1974

By M Wilson, D Whiteman, P Kuiper, S Talu, G Watt, A van As

Once the draw process has begun in a block cave, it is very difficult to identify which regions of the cave have successfully propagated, where the caved material is flowing from and where it is flowing to. The uncertainty around cave flow increases as the cave is drawn and can be further compounded by poor draw control practices. These uncertainties make it difficult to plan effective draw strategies to control dilution, as flow model predictions tend to gradually diverge from the actual state of the cave. There have been documented occasions where observed caving phenomena, such as muck pile surface rilling, could not be reproduced with the cave flow models of the time. The ultimate consequence of cave flow uncertainty is generally manifest as higher dilution and lower grades.In order to measure the real-time flow of caved material within an active block cave, CRC Mining and Elexon have developed, together with Rio Tinto, a cave flow monitoring system called Cave Tracker, which is being trialled at Argyle Diamond Mine (ADM) in Western Australia. The Cave Tracker system at ADM comprises electronic ‘beacons’ that have been installed down long HQ diameter drill holes located above the extraction level. As the cave-back propagates and the rock mass fragments, beacons are released into the muck pile and flow along with the caved material to the drawpoints below. At Argyle, the beacons are configured to emit a signal every three days. These signals are picked up by detectors installed on the extraction and undercut levels, allowing the positions of the beacons to be determined.By examining the real-time material flow in different regions of the cave, flow mechanisms can be better defined. Draw control strategies can then be actively tailored to manage the current state of the cave. Thus, previously undetectable indications of excessive rilling, rapid cave propagation, cave stall, air gaps and dilution entry can now be identified early and assessed continuously as the cave progresses. For the first time it is possible to amend draw strategies based on measurements from inside and outside of the fractured zones, allowing caves to be managed more effectively.CITATION:Whiteman, D, Talu, S, Wilson, M, Watt, G, Van As, A and Kuiper, P, 2016. Cave Tracker flow monitoring system installation at Argyle Diamond Mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 479–488 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Frik Badenhorst, René Roux, Peter Terbrugge

This paper presents a case study where economics dictated an aggressive slope angle and where an appropriate slope management programme allowed successful completion of mining to 190m below surface. The Navachab Gold Mine is located in Namibia and is one of the few gold mines in that country. Mining by open pit methods commenced in 1990 with economics dictating an aggressive slope design to minimise waste stripping and make the mine viable. With steep slope angles in the design, and a steeply dipping footwall geology, it was necessary to introduce a comprehensive slope management programme. This required good mining practice in limit blast techniques with pre-splits and trims, and good housekeeping to effect a safe and economical operation. The slope management programme in addition required in pit mapping and logging procedures, regular survey monitoring evolving to a robotic Geomos system, as well as slope instrumentation to monitor stability. Two relatively large scale failures occurred at the mine, the second of which impacted on the east wall access ramp, while the first was confined to an operating stack. The paper describes the design and slope management techniques developed for the east wall.

Jan 1, 2006

Ecuador a gross domestic product (GDP) grew 8% despite a slowdown in production and sales of petroleum, the dominant economic sector. Crude petroleum exports, which amounted to about 35% of total exports in 1977, were valued et $484 million,2 a decrease of 14% from 1976 values. Petroleum export sales were depressed because foreign buyers were somewhat uncertain that State-owned Corporación Estatal Petrólera Ecuatoriana (CEPE) held legal title to the oil until final settlement with Ecuadorian Gulf Oil Corp. In addition to the legal complication, Ecuador maintained a relatively high export price for oil until late in the year. There was also a shrinkage of traditional U.S, markets owing to the Alaskan pipeline becoming operational and an increased availability of Mexican supplies. The export market was also affected by increased domestic production in Peru and Chile, which lessened their import needs, and the pressure of greater competition from the Middle East in supplying crude oil to Caribbean refineries. About 20.4 million barrels or 40% of Ecuador's total crude exports went to the United States. Only 27 wells were drilled in Ecuador during L977; of these, 16 produced oil, 3 were dry holes, and 8 were suspended. About 31 wells were planned for 1978. Three new oilfields were discovered during 1977; two by CEPE in northeastern Ecuador and one by the Argentine State oil company Yacimientos Petraliferos Fiscales (YPF), operating in Ecuador under a service contract. CEPE's two discoveries tested at 5,000 and 1.450 barrels per day, respectively. The YPF discovery tested at about 1,000 barrels per day. Ecuador altered its position regarding

Jan 1, 1981

By Roberto Maldonado Astorga

El presente texto señala la implementación del modelo de gestión para las operaciones de Volcán Campaña Minera, basado en el Modelo de Gestión de Malcom Baldrige. El modelo tiene el objetivo de establecer un proceso sistemático y estandarizado que asegure la mejora contínua y en línea con la visión de la empresa que apunta al logro de la excelencia operativa. La estrategia se divide en tres módulos: Módulo de Organización, Módulo de Gestión y Módulo de Comunicación. Asimismo se busca, implementar círculos de optimización permanente, monitorear de forma sistemática la ejecución de iniciativas de mejora y seguir el impacto en los indicadores.

Nov 1, 2014

Horizontal holes are drilled underground into coalbeds to control methane flow from ribs and active face areas and to make gas pressure measurements in coalbeds. Gas pressure measurements are made by drilling the same hole incrementally. After each increment, the hole is filled with some type of packers and allowed to reach equilibrium before a gas pressure reading is taken. As the length of hole increases, more packers are required to effect a seal and obtain a reliable pressure measurement. Problems have been encountered in obtaining satisfactory packer seals due to the friable nature of the coalbed. New methods of packing the holes must be used. Therefore, this project was established to evaluate materials and develop a new technique in which a semiliquid and/ or rigid type grout could be placed in the hole to provide satisfactory sealing.

Jan 1, 1972

"The effective thermal conductivity (ETC) is one of the most important thermo-physical properties of porous media. Due to the lack of higher precision influence of temperature on thermal conductivity, we took 6 groups of experiments on rock samples (including igneous rock, sedimentary rock and metamorphic rock) under different operating temperatures from 20? to 50? by 7 acquisition points. The general equation of thermal conductivity drives the value of it increasing along with the decreases of the temperature. While in our experiments, it is easy to find a singularity among them for each sample. The experimental investigations we attempted to observe and interpret the alteration mechanism. According to the Heat Capacity Theory in solid state physics, this research gives the explanation about the “singularity” from 3 understanding of specific heat, average free path, and thermal conductivity. Our research divided the condition of the rock thermal conductivity into 3 different types. INTRODUCTION The effective thermal conductivity (ETC) is one of the most important thermo-physical properties of porous media(Huang & Han ,1988; Peierles ,1955). This parameter is necessary for analysis of heat transfer(Vaferi et al, 2014;Hans-Dieter & Rudiger,2003). It’s well known that a general equation for ?(T) was set by Sass et al. (1992) which based on the coupled effect of composition and temperature on the thermal conductivity(Jesse et al, 2013; Mongelli et al,1982).The equation was further successfully verified for other rock (Zumrud et al,2010;Abdulagatova et al,2009;Seipold& Huenges,1998).Thermal conductivity is also related to other physical proper ties of porous rock, such as thermal diffusivity, heat capacity(Brettmann et al,2011;Abuel-Naga et al,2008). It is well known that ETC and other thermo physical properties of rock materials are affected by various factors, such as temperature, pressure, mineralogical composition, porosity, stratification, size and shape of the components, and nature of pore fluid, etc. (Tiedje & Guo, 2014; Touloukian et al,1970).The understanding of heat transport processes still requires the knowledge of thermal properties of rocks."

Jan 1, 2015

To improve the ventilation of large-opening under-ground stone mines by using stoppings made from stone left in place. Background Underground stone mines typically use large room-and-pillar openings with little ventilation control. Stone miners may be exposed to contaminants that include silica dust, diesel particulate matter (DPM), exhaust gases, nuisance dust, and face shot (blasting) fume gases. The health risks from breathing these fine particles and toxic organic materials are well documented. Although contaminants such as dust or diesel exhaust can be some-what controlled at the source, the escaping contaminants are often diluted and removed from work areas using ventilation with minimal controls. In many cases, current mine ventilation practices use trial-and-error techniques to improve ventilation. The growing realization of the importance of a healthy work environment along with increased regulations will require many stone mines to implement new ways to improve ventilation. In-place stone stoppings are one option. Mine air flows from one point to another because of a pressure differential between those points. This pressure differential is established using a mechanical fan in conjunction with separations (stoppings) between high-pressure (intake) and low-pressure (return) airways. The separation of intakes and returns is an important concept that is used in most other types of mines. Normally, air moves through underground stone mines with minimal control technology. Fans are placed in locations where they are thought to be most beneficial, and intakes are not separated from returns. In a few smaller underground stone mines, proper ventilation can be achieved with a few strategically placed fans. However, as these mines increase in size, moving adequate quantities of air through-out the mine becomes harder, and separation of intakes and returns becomes a problem. Building traditional mine stoppings to separate the intake and return airways in entries with a cross-section area often exceeding 800 ft2 is difficult. The stoppings must be able to withstand both the dynamic pressure from face shots and the static pressures created by the fans. Construction and maintenance difficulties, as well as high costs, are the main factors preventing these traditional mine stoppings from gaining wide acceptance by the stone mining industry.

Dec 1, 2002

By A. M. Poston

Introduction of radioactive elements into ore samples and/or pregnant liquors and radiometric tracing thereof have greatly improved control of fusion and extraction studies on beryllium ores and products. Extractive metallurgical research on beryllium, normally guided by the usual laborious analytical methods, is both costly and slow. Recognition of this problem by the Bureau of Mines led to the development and application of radioisotope tracer techniques" as a substitute for chemical analysis at the Salt Lake City Metallurgy Research Center, The result was that much faster progress at significantly lower cost was achieved. This report discusses the problems encountered and resolved in using radioactive tracers and radiometric methods, defines the conditions and techniques for their effective use, and delineates the limitations and flexibility inherent in applying such methods in laboratory-scale beryllium research.

Jan 1, 1962

By W. M. Dressel

This Bureau of Mines report describes a shaft closure demonstration project in which 11 inverted pyramid-shaped plugs were used to plug abandoned open mine shafts in Galena, KS, The inverted pyramid-shaped forms, fabricated from steelplate, were designed so that the inverted base would be larger, by 4 ft on a side, than the approximate size of the shaft opening at the surface residuum-solid rock interface. After the surface openings of the shafts were trimmed with a backhoe, the steel forms, complete with reinforcing, were lowered into the openings and filled with concrete; the remaining portions of the openings above the plugs were backfilled to slightly above the surrounding surface level with waste rock and soil. Location and elevation monuments were installed for long-tern evaluation of the success of the project.

Jan 1, 1985

By J. F. Archibald

A research effort has been undertaken, under Workplace Safety and Insurance Board of Ontario (WSIB) sponsorship, to characterize the support capabilities of conventional and innovative spray-on lining materials for mitigating dynamic failure effects created by simulated rockbursts. Conventional spray support media, such as shotcrete and fibrecrete linings, and a variety of new spray-on lining materials [thin, spray-on liners (TSLs)], typically polymer-type thin coatings, were subjected to simulated rockburst influence. For baseline comparison, conventional rockbolt and bolt-and-mesh support products were also evaluated. Observation of lining performance was undertaken through completion of field-scale support and rock detonation trials. Controlled blasting tests were conducted at the Queen’s University Explosives Laboratory to examine the effectiveness of the variety of surface coating agents for modifying dynamic rock spalling processes. All tests were performed upon largely undisturbed and homogeneous rock materials in highly repeatable fashion. All blasts were observed seismically and photographically to provide detailed information concerning rock motion, surface fracturing, ejected fragment motion and support liner survivability characteristics. These material comparison trials were performed to assess the relative effectiveness of a wide range of currently available area support techniques for suppressing hazards associated with dynamic rock ejection. The results of this study validate that thin, spray-on linings may be equally as effective, and often better, than conventional support materials at mitigating rockburst or like damage in highly stressed mine environments.

Jan 1, 2004

By D. S. Burgess

About 100 tests of flammability were carried out with H2, CH4, and CO in mixtures with air using the Federal Bureau of Mines 12-ft-diameter spherical pressure vessel as an explosion test chamber. The LeChatelier approximation gave slightly conservative estimates of the limits of downward flame propagation (onset of significant pressure rise) using the following measured values for the individual gases, in percent: H2, 8.5; CH4, 5.25; CO, 13.0. No justification could be offered for using the LeChatelier law for upward flame propagation limits and indeed reported data suggest that calculated values would not be conservative. The observed upward limit for methane-air mixtures (4.85 pct) was less than the widely accepted lean limit for this fuel; those for lean hydrogen-air mixtures and carbon monoxide-air mixtures did not differ from the lowest accepted values. Diffusional effects on the propagation of single, binary, and ternary fuel mixtures are discussed.

Jan 1, 1982

By A. Cole, A. Bolland

The roasting and gas handling circuits at Goldstrikes' new Roasting Facility incorporate proven technologies in a unique combination. During the design of the plant, every effort was made to utilize the best available unit operations from the perspective of capital, environment and operating costs. The roaster utilizes Freeport-McMoRan whole ore roasting technology with pure oxygen as the oxidizing gas. This process was chosen based on its proven application on Carlin-type carbonaceous ores. An extensive gas cleaning train follows the roaster and comprises direct cooling, dust scrubbing, indirect cooling, wet electrostatic precipitation, mercury scrubbing, SO2 scrubbing, CO incineration and NOX reduction.

Jan 1, 2001

By Claudio Flores Martinez

The prospect of accomplishing economically and scientifically profitable deep-sea mineral mining within this decade or the next one is of particular interest to the emerging discipline of astrobiology which is concerned with the origin, distribution and future of life in the Universe. Several planetary bodies within our own Solar System such as Jupiter’s moon Europa and Saturn’s Enceladus now appear to be potentially habitable, or life-friendly, in terms of the three prerequisites for life as we know it: a sustained body of liquid water, biogenic elements (C, H, N, O, P, S) and energy sources to fuel metabolic reactions. Europa, for instance, possesses a global subsurface ocean, believed to be up to 100 km in depth, hidden beneath a kilometer-wide ice-sheet. A silicate mantle is directly interacting with a cold, aphotic ocean in which tidal forces might drive geological seafloor activity that results in the creation of hydrothermal systems. These locales are commonly hypothesized to be the cradles for an alternate origin of life on Europa. Especially alkaline hydrothermal springs, as found at Lost City, have been at the center of modeling the prebiological evolutionary dynamics preceding cellular life. Serpentinization-like reactions are also possibly fueling metabolic networks in putative microbial communities found in the oceans of the icy moos. Major space agencies around the globe are planning future space missions aimed at exploring and eventually characterizing potential life forms in these habitats. The technology needed for this exploration effort resembles the requirements for a successful deep-sea mineral mining industry: highly efficient AUVs (also equipped with biologically-oriented instrumentation), swarm robotics, landers, seafloor rovers and general high-pressure, cold temperature extreme environment engineering. Interestingly, science questions of deep-sea mineral mining and astrobiology converge too: the hypothesis of life originating at hydrothermal systems, the biogeographical distribution of species among these environments, adaptations of extremophilic organisms across the three domains of life and adequate autonomous robotic systems to assess the complexity of deep-sea biological communities. This presentation attempts to present a two-fold view of advanced planetary exploration that relates to a sustainable vision of deep-sea mineral mining: charting our oceans and developing technologies least harmful to endemic biology can propel the design and prototyping of future robotic planetary probes bound for aquatic missions on alien moons. Space industry, government and public interest towards a broadened planetary perspective on deep-sea mineral mining is promoted by addressing an astrobiological rationale of this endeavor.

Sep 1, 2014

By Jay Rodgers

There has been a longstanding acceptance that burden plays a major role in the magnitude of ground vibration amplitudes generated from surface blasting. Much of the data that this belief is based upon is empirical in nature and may or may not represent an example of false inference. Recent published reports have rightly questioned the influence of burden and confinement on blast vibration amplitude, suggesting that the fracture condition of the rock mass is a better indicator. The increased investment in electronic detonators as a tool to control ground vibration amplitudes demands an understanding of vibration production detailed enough to make use of the vastly improved timing accuracy that they provide. A more accurate relationship may be found if we strip away the assumptions of the past and search for the underlying mechanism of vibration production in surface blasting. We must answer the question: What happens at or near the borehole when an explosive charge detonates that produces ground vibrations?

Jan 1, 2003

By R. Weber

Methane explosions in underground coal mines are a major concern across the mining industry. After the Pike River disaster, Arnot Coal became even more aware of the explosion risk. To determine whether Arnot has adequate precautions against a methane explosion, such as the one that led to the Pike River disaster, a literature survey covering the causes of the incident and what preventative measures should have been in place was conducted. Many different methane explosion prevention methods were evaluated, as well as codes of practice. Based on the findings, Arnot?s measures to prevent conditions favourable for a methane explosion were evaluated.

Jan 1, 2014

Detailed investigation was carried out on the dephosphorization of a number of phosphorus-rich manganese or samples of India by leaching with dilute sulphuric acid. Various process parameters like concentration of acid, liquid-solid ratio, temperature of leaching, time of leaching, and particle size of the ore were studied in detail for the three samples of manganese ore from central India, and optimum values were worked out on a laboratory scale. Preliminary studies show that certain ores which are not easily amemlible to appreciable dephosphorization by leaching with dilute sulphuric acid can be made amenable by :roasting to 700-900°C before leaching.

Jan 1, 1974

By P Rubie, B Morgan, J Russell, C Stewart

The relationship between efficient liner exchange, concentrator availability and concentrator profitability is well documented. Russell Mineral Equipment’s (RME) relationship with OZ Minerals’ Prominent Hill site personnel enabled sound collaboration between the two parties. Both parties worked together to identify the sources of productivity and efficiency loss and developed solutions to reverse them.This paper chronicles the identification of production inefficiencies and the resulting removal of mill relining from the critical path through the materialisation of mill relining optimisation strategies. Furthermore, this paper outlines other recent mill relining optimisation strategies developed by RME and tested at Prominent Hill, to demonstrate and achieve further productivity, efficiency and safety improvements.CITATION:Rubie, P, Russell, J, Morgan, B and Stewart, C, 2017. Mill relining optimisation – a story of collaboration, in Proceedings MetPlant 2017, pp 335–345 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By P Ridgeway, D Xie, M A. Somerville, S Jahanshahi, H Rogers, J G. Mathieson, Y Pan, N Haque, P Zulli, T E. Norgate, L Lu, A Deev

In 2006 the Australian steel industry and CSIRO initiated an R&D program to reduce the industry’s net greenhouse emission by at least 50%. Given that most of the CO2 emissions in steel production occur during the reduction of iron ore to hot metal through use of coal and coke, a key focus of this program has been to substitute these with renewable carbon (charcoal) sourced from sustainable sources such as plantations of biomass species. Another key component of the program has been to recover the waste heat from molten slags and produce a by-product that could be substituted for Portland cement. This paper provides an overview of the low-emission Integrated Steelmaking Process, progress made over the past seven years and the program’s future direction which includes proposed demonstrations of the technologies developed including large scale piloting and full scale plant trials.

Jan 1, 2014

When asked to lecture at Bendigo on the geological factors that determine the depths of ore deposits, I hesitated for a little before agreeing to lecture on the theory of deep ores in the city world famous as the pioneer of deep gold mining. If there be one place, wherein the conditions of deep-seated ore deposits should be sufficiently well understood, it is the city where the 180 mine made its bold plunge to previously neglected depths; and where the record of that famous mine has been broken by the skill of the managers, and the pluck of the proprietors, of the New Chum Railway and Lazarus mines.In the face of such practical triumphs, theoretical discussion may seem a waste of time, especially since it is often dedared that the existence of such deep-seated ores was denied by geological theory. This assertion is, however, startling since the oldest and best supported geoiogical theory of ore deposits, has taught for more than a century tliat ores must descend far below the regions of practical mining. This charge against Victorian geologists is generally based on opinions attributed to the late Sir Fredrick McCoy. It has been repeatedly affirmed that he declared that gold cannot occur pelow a depth of 300 feet. But so far I have not been able to discover that McCoy ever made any such assertion or ever held such a view.

Jan 1, 1902