Search Documents

By William J. Rothschild

Ground water at construction sites can be controlled by properly placed wellpoint dewatering systems. Care must be taken in planning cofferdams to have adequate space for and access to pumps, headers and the points. A most important part of dewatering is protection of adjacent structures from movement. A checklist gives items to consider in bidding.

Jan 1, 1984

By James L. Vinson

Wilbur Smith Associates (WSA) has provided planning, engineering and construction oversight assistance to the Tennessee Department of Transportation (TDOT) for three construction projects intended to widen and improve segments of I-40 and associated interchanges in Knoxville, Tennessee. The projects are within the karst terrain of the Valley and Ridge Province. Subsurface conditions are characterized by an irregular rock surface coupled with differential weathering. Because of the projects? impact to local and interstate motorists, consideration was given to innovative planning, materials and construction practices that could accelerate construction. Two innovative deep foundation measures included rock-socketed pipe piles, which act as both foundations and substructure elements for a bridge?s interior bents, and the first widespread use of rock-socketed drilled shafts as bridge foundations on a TDOT project. The pipe piles were used at a site with significant cavities within the limestone bedrock. This resulted in design verification and constructability difficulties that required delays, but measures were ultimately employed to produce a sound foundation system. Over 110 drilled shafts have been constructed at sites with generally low solution activity. Relative to H-pile footings, which were included as an alternate foundation, they have apparently allowed accelerated construction at a competitive cost.

Jan 1, 2006

By V. F. Parry

Subbituminous coal or lignite when stored in random riles or in ordinary bins in which the temperature fluctuates and air circulates quickly undergoes objectionable physical and chemical changes, which decrease the utilization value of the fuel and increase its tendency to ignite spontaneously. Slacking takes place, and the heating value decreases. Those changes are accelerated by fluctuations of temperature and by circulation of air through the storage space. When such coals are exposed to the weather they lose moisture rapidly. If evaporation from the surface of a lump proceeds at a faster rate than that at which it is replaced by moisture from the interior, the rate of shrinkage at the surface is greater than that at the interior; consequently stresses are generated at the surface which cause the coal to disintegrate. Likewise, when moisture is absorbed by the air-dried surface the outside layers expand at a faster rate than the interior, which results in further break-down. As these cycles are repeated the lump may disintegrate completely. Therefore, successful storage of low-rank coals depends on control of the factors that influence change of moisture.

Jan 1, 1941

By Pramod C. Thakur

In This Chapter [Origins of coalbed methane Reservoir properties of coal seams Thresholds for coal seam degasification Methane emissions in mines Methane drainage techniques How to transport gas safely in mine pipelines and Economics of coal seam degasification Recommended publications on coal seam degasification are Gas Control in Underground Coal Mining [Creedy et al. 1997], Coalbed Methane Extraction [Davidson et al. 1995], and Methane Control for Underground Coal Mines [Diamond 1994].] ORIGINS OF COALBED METHANE AND RESERVOIR PROPERTIES OF COAL SEAMS Origins of coalbed methane. Coal seams form over millions of years by the biochemical decay and metamorphic transformation of plant materials. This coalification process produces large quantities of byproduct gases, such as methane and carbon dioxide. The amount of these byproducts increases with the rank of coal. It is the highest for anthracite, where for every ton of coal nearly 1,900 lb of water, 2,420 lb (20,000 ft3) of carbon dioxide, and 1,186 lb (27,000 ft3) of methane are produced [Hargraves 1973]. Most of these gases escape to the atmosphere during the coalification process, but a small fraction is retained in the coal. The amount of gas retained in the coal depends on a number of factors, such as the rank of coal, the depth of burial, the type of rock in the immediate roof and floor, local geologic anomalies, and the tectonic pressures and temperatures prevalent at that time. The gases are contained under pressure and mainly adsorbed on the surface of the coal matrix, but a small fraction of gases is also present in the fracture net-work of the coal. Methane is the major component of gases in coal, comprising 80%–90% or more of the total gas volume. The balance is made up of ethane, propane, butane, carbon dioxide, hydrogen, oxygen, and argon.

Jan 6, 2006

A substantial proportion of current and historic West Coast gold production comes from deposits situated around the margins of æice ageÆ glaciers. Gold has been eroded and transported by glacial ice then deposited in till and outwash gravel. The interplay between fluvial and glacial processes, climate, basement geology, tectonic uplift, sediment supply and sea level dictates many aspects of the development of the West Coast landscape. The way in which the external forcing factors interact is crucial in determining the gold content of placer deposits in this region. The following is an outline of some of the factors that influence the gold distribution in vicinity of glacial margins.

Jan 1, 2000

Productivity in underground metal and nonmetal mines is contingent upon work methods, mine layout, and ore handling techniques. One of the most important factors impacting productivity is the efficient movement of men, materials and supplies from the surface into and throughout the mine. Various transportation systems such as man-trains, service shafts, rubber-tired diesel equipment, etc. are currently used to transport men and supplies in underground mines. In many underground mines, it is not uncommon for a worker to spend 25% of his eight-hour working day traveling from the surface to his work area and returning to the surface.

Jan 1, 1975

By A. C. Smith

The U.S. Bureau of Mines constructed a large-scaJe facility to study the self-heating of a large coal mass under conditions that simulate a gob area of a mine. The insulated coal chamber can hold up to 13 short tons (st) of coal and is provided with a forced ventilation system and computer-controlled temperature and gas measurement systems to monitor the heat and mass transfer phenomena that occur in the coalbed. Three experiments were completed with high-volatile C bituminous coals that exhibited high spontaneous combustion potentials in laboratory-scale tests. In the first two tests, a sustained heating was not achieved. In the third test, temperatures throughout the coalbed increased steadily from the start, with thermal runaway occurring near the center of the coalbed after 23 days. The thermal reaction wne then moved toward the front of the coalbed. The results of these tests showed that the self-heating of a large coal mass depends not just on the reactivity of the coal, but also on the particle size of the coal, the freshness of the coal surfaces, the heat-of-wetting effect, and the availability of O2 at optimum ventilation rates.

Jan 1, 1991

By Kristie Tarr

Portland cement is primarily used to solidify backfill in underground mine workings and it represents a major cost in mining operations. CANMET-MMSL has invented an alternative binder technology that does not contain any amount of Portland cement and is made using waste materials, such as development rock and smelter slag. The technology has been successfully tested with many types of base metal and ferrous slag. Research conducted in collaboration with several mining operations in Canada has shown that the CANMET-MMSL binder has considerable potential as a replacement for Portland cement in mine backfill. An integral part of the overall mining operation, backfill is used for two main purposes: safety and environmental remediation. Depending on the mining method used, backfill provides a working surface, stabilizes stope and pillar walls, as well as the surrounding rock mass, and controls caving of stope backs. There are several benefits associated with the replacement of Portland cement in backfill, including reductions in (i) the footprint by placement of slag waste underground, (ii) the environmental effects and long term liability resulting from disposal and containment of slag waste on surface such as acid rock drainage, (iii) GHG as a result of reduced Portland cement usage (the production of 1 ton of Portland cement produces 1 ton of GHG), and (iv) the significant costs associated with reduced Portland cement usage.

Oct 1, 2010

By James S. Graham

Foundation pile driving hammers used in New York City in the past 100 years have been drop, steam, compressed air, diesel, and hydraulic. In 1992, the first hydraulic hammer in the New York City area was purchased by Norwalk Marine Contractors, Inc. from Junttan in Finland. It was bought because of its variable energy and ease of mobilization, not because of its higher transferred energy. Heller and Johnsen engineers instrumented hydraulic hammers on nine jobs. The measured transferred energy for the nine jobs was found to average approximately 80 percent. There is no clear consensus regarding the reasons for the hydraulic hammer being more efficient in delivering energy to the pile as compared to single-acting steam/air impact hammers. To minimize pile damage during installation, and to minimize footage overruns, an up-to-date version of the wave equation software that includes an efficiency value of 0.95 for hydraulic hammers is now used.

Jan 1, 2000

By C. E. McManus

MANY mechanical advances have been made on mining equipment during the year 1951. There have been a number of trends established and many modifications made on open-pit equipment to increase the efficiency and availability of all the machines necessary in the moving of overburden and iron ore. Some years ago, the trend toward larger shovels for the loading of off-highway trucks began, but in the last year, it has become general practice to use the 5 to 7 ¼ -yd quarry-type shovels in the loading of haulage units. For years these larger shovels were used in the locomotive haulage pits. As the truck capacities increased from 15 to 20 to 30 tons, the need for larger loading units became apparent. Today in most mines, large shovels are in evidence and a few 8-yd shovels will be delivered this year for loading off-highway trucks. Torque Converter-Shovel The Diesel-driven shovel with its friction bands has been modernized with the torque converter. There have been about ten shovels remodeled to take a torque converter in the drive system. The large high-torque, low-speed Diesel engine was removed and replaced by a high-horsepower, high-speed, automotive-type engine. This engine was connected directly to the torque converter. The torque converter was connected to the shovel through the standard original sprocket and chain. Dual governors controlled engine performance. One governor controlled the high idle of the engine; the other governor, which is connected through a flexible shaft to the output shaft of the converter, controlled the loading of the engine. With this dual governor hook-up, the engine anticipates load conditions and is operating at high idle and full throttle before the shovel load is transmitted back through the converter to the flywheel. It has been found that with this automotive-type engine and converter, the shovel capacity has been increased about 20 pct. Also, the wear on the friction bands, breakage of hoist cables, and other mechanical breakages has been reduced materially. Alloy-Steel in Shovels The shovel equipment manufacturers have been experimenting with low-temperature-strength, high-alloy steels to combat the excessive breakage that occurs in extremely cold weather. High-nickel alloy steel has been used in critical areas that are affected by low temperatures, the most notable being dipper sticks. Most shovels ordered today are equipped with some of this special, alloy steel. More and more manganese alloy is being used for replacement parts such as shovel pads, idlers, drive sprockets, etc. Although the initial cost of these parts is considerably higher than the standard replacement items, the life of these manganese parts is considerably longer and well worth the added expenditure. Dipper-teeth repair is still a problem. Most companies use the small replaceable inserted tooth. It has become common practice among some of the companies to "job out" their dipper-tooth repairs to outside welding companies. This necessitates an additional inventory of teeth, but it does guarantee an adequate supply of replacement teeth at all times. These contractors have set up their shops on a production basis and can do an acceptable job at a high rate of speed. Thermite welding has been used in retipping teeth. To date, the process cannot be called successful but with improvements the time required to repoint the dipper teeth will be decreased considerably. The submerged arc process has been tried in the replacement of these dipper points, but like thermite welding has not proven successful. Here again, if a method can be developed to use submerged arc, the job of teeth repair will be made much easier. New model shovels in 6 ½ and 8 cu yd sizes fea-

Jan 1, 1952

By V. V. Nazimko

Abandoned coal mines cause subsidence and structural damages. Shallow abandoned mines induce the most severe and harmful damages. In addition, they produce time-dependent subsidence which is difficult to predict. Backfilling of underground cavities with waste materials have been used to prevent the time-dependent subsidence or to mitigate its effect. However, this procedure is expensive. A new drill and blast technique has recently been proposed to prevent surface damage from time¬dependent subsidence over abandoned mines. It utilizes the principle that blasting in the caved rock and roof in the vicinity of a cavity will dilate the ground and create a self-supporting effect owing to increase in the volume. Physical modeling has demonstrated that artificial dilation of caved rock using the drill & blast technique creates positive effects due to the following sequence of events: the dilated rock creates a supporting effect for the suspended rock strata and reduces its span which decelerates 3.4 times the process of caving. The roof span is reduced by the next caved layer, which causes the hole boundaries to incline to each other. This effect converts the process of caving from a developing mode to a reduction mode. Finally, the sinkhole zone assumes a triangular shape with a negative angle of draw 64-700 in contrast to a rectangular shape of the chimney zone for natural caving. Vertical dimension of the triangular zone is 3.87 times of the room height. Final surface subsidence decreases at least 2.09 times; displacement 1.31 times, slope 2 27 times; curvature 3.42 times, horizontal strain 1 21 times in comparison to natural caving of the ground over an abandoned mine.

Jan 1, 1999

By Rick Deschamps, Brian Barkauskas, Aled Hughes, Abigail Stein

In central Washington, six miles south of the small town of Vantage, the flow of the Columbia River is harnessed by the Wanapum Dam which is part of the Priest Rapids Hydroelectric Project owned and operated by Grant County Public Utility District (GCPUD). Extending more than 8,300-feet from bank to bank, the dam includes left and right earth embankments, left and right concrete gravity sections and a 10-unit powerhouse. Adjacent to the right embankment is a concrete gravity spillway featuring radial gates measuring 50-feet-wide and nearly 70-feet-high. In the early 1960’s when Wanapum Dam was built, these seven-story spillway gates were the highest in the world. In late February 2014, 50-years into its service life, during a routine maintenance inspection, observant workers noticed a slight misalignment in the roadway deck curbs and handrails located on top of the spillway. Further survey and inspection efforts uncovered a 65-foot-long by two- inch-wide crack that spanned the full length of Monolith 4. On discovering the extent of the damage, GCPUD initiated immediate drawdown of the reservoir to relieve pressure on the spillway monoliths. Wanapum Reservoir and the areas directly downstream of the dam were immediately closed, boat ramps and inlets were left completely dry, campsites were closed and boating activity was banned on the lake until further investigations and remedial procedures were in place and completed. An extensive root cause analysis ultimately led to the conclusion that errors in the initial design calculations and late changes to the final spillway design led to a condition that generated tensile stresses in the concrete at the upstream face, which over a period of 50-years resulted in the formation of a crack along a horizontal lift joint located about 85-feet below normal pool elevation. Further analysis showed that, although visible distress was found at Monolith 4, there was nothing preventing this issue from happening at other locations along the dam spillway. Although no visible cracking was found in the other monoliths, repair procedures for Monolith 4 would have to be replicated at the remaining monoliths.

Jan 1, 2018

By Ramón Noriega

Al mes de mayo de 2022 en nuestro país se han reportado 205 conflictos sociales, de los cuales 130 son socioambientales y se encuentran vinculados al sector minero energético; este alto número nos ha llevado a analizar los procedimientos y mecanismos que los actores dan a estas demandas sociales y verificar su efectividad. El articulo además propone la aplicación de la gestión de riesgos en los conflictos sociales como una herramienta que podría mejorar la adecuada gestión de la conflictividad social.

Sep 30, 2022

By David Schlain

The Bureau of Mines investigated methods for electrodepositing platinum-group metals from molten cyanide baths. The preparation of thick, protective coatings on molybdenum, Inconel, graphite, stainless steel, copper, and other structural metals were studied, as well as the electroforming of platinum and iridium crucibles. Iridium, rhodium, and ruthenium can be electrodeposited under an inert atmosphere, while platinum and palladium require the presence of air. Electrolytes may be prepared by direct-current electrolysis in NaCN or mixtures of NaCN and KCN using anodes of the particular platinum-group metal. When the concentration of metal increases to about 0.3 or 0.4 percent, the deposits become bright, adherent, and coherent. Current densities may be 10 to 25 ma/cm2, and plating rates are often 0.5 mil/hr. Platinum and palladium baths deteriorate because of the oxidation of cyanide to cyanate and carbonate, and the precipitation of metal. Changes in the platinum cyanide bath are relatively slow. The protection against oxidation afforded by the platinum-group metal coatings is evaluated by testing encapsulated specimens in a thermogravimetric balance. Surface pretreatment and the use of undercoats are discussed.

Jan 1, 1977

By Terry R. Neumann

This document, prepared for the U.S. Bureau of Mines Regional Mineral Assessment Program, presents data pertinent to the mineral resource assessment of the Needles 1° x 2° map quadrangle (excluding the Arizona portion), located in the Mojave Desert southeastern California. The U.S. Bureau of Mines (USBM) mineral survey of the quadrangle, conducted from 1991 to 1993, was done to provide the minerals data necessary to support effective land use planning and resource decision making. To this end, this report (1) inventories historic and current mining activity, (2) inventories identified resources, (3) provides an economic analysis; of identified mineral resources and estimates their feasibility for development, (4) delineates areas of exploration and development potential based on current geological, geochemical, and geophysical information, (5) supplies information on land status, transportation networks, power supplies, water availability, and regulations, and (6) analyzes socio-economic impacts of potential mining. The Needles quadrangle is in the Basin and Range province of the southwestern United Van. The area is underlain by a lithologically and structurally complex Proterozoic crystalline basement of gneiss and granite that is overlain by sparse, scattered outcrops of deformed and metamorphosed Late Proterozoic and Paleozoic sedimentary sequences. Mesozoic granitic plutons, particularly in the western half of the quadrangle, intruded the basement and sedimentary rocks, resulting in metamorphism and deformation responsible for the formation of high-grade gneisses and mylonitic rocks (core complex) in the eastern part of the quadrangle. Voluminous Tertiary volcanism unconformably overlie some older sequences. The structure of the area is dominated by Basin and Range extensional block faulting; in the eastern part of the area, block faulting is accompanied by widespread low-angle detachment faulting associated with core complex development.

Jan 1, 1993

By Carolyn Kenney, Jianjun Liu, Zhenghe Xu

"The flotation of fine particles has been a challenge to scientists and engineers in mineral processing. A novel concept of reactive oily-bubbles as carrier to float fine particles is described in this paper. The reactive oily bubble flotation is considered attractive for fine particle flotation. In addition to the role of fine particle agglomeration by oily films, the surface properties of air bubbles coated with a thin oil film can be better controlled for the desired selectivity by adding certain types and concentrations of water insoluble collectors into the oil phase. This approach can eliminate the addition of collector to the aqueous phase, avoid undesired synergetic interactions among collectors, activators, depressants and dispersants present in slurry, minimize undesired activation of gangue particles and significantly reduce the amount of collectors needed.The concept of using reactive oily-bubble to achieve selective flotation was demonstrated in contact angle measurement and by microflotation tests with fine sulphide minerals: sphalerite and galena in this paper. The flotation behavior of sulfide minerals can be radically modified with adjustment of solution pH, addition of depressant and activator as in conventional flotation. The successful separation between PbS/SiO2, ZnS/SiO2 and PbS/ZnS was demonstrated using mixed mineral systems. Compared with conventional flotation, the reactive oily-bubble flotation showed a stronger collecting power.INTRODUCTIONThe challenge for fine particle flotation has long been recognized and well documented (Fuerstenau, 1980). Because of drastic changes in surface properties of fine particles and associated physicochemical and hydrodynamic conditions of flotation systems, fine particles responded poorly to the conventional flotation processes. For instance, the small mass and hence low inertia of fine particles would result in a low efficiency of collision and attachment of fine particles with flotation bubbles. Large specific surface area of fine particles, on the other hand, would cause an increased reagent consumption. Dominating colloidal forces of fines may cause slime-coating, accompanying a low selectivity (Somasundaran & Arbiter, 1979; Fuerstenau, 1980; Sivamohan, 1990)."

Jan 1, 2003

Silica reacts with cryolite at 1010°C in two stages. The first stage is the formation of a sodium aluminosilicate of composition consistent with the mineral jadeite (Na20.AI20s.4Si02). The formation proceeds by atleast two different reactions. Formation of alumina or an aluminosilicate proceeds to its limiting value in the first 30 min while the formation of jadeite proceeds at a steady rate until quantitative conversion is achieved after 150 min. The net overall reaction can be expressed by the equation 6 Si02+2 Na3AlF6? (Na20.AI20s.4Si02) +2 SiF4 +4NaF.The second stage involves a slow reaction that proceeds with the evolution of a little SiF4, The net result is the formation of sodium aluminosilicates that are soluble in 30 per cent AlCIs-HCI solutions. While this could be explained by disproportionation of jadeite to form albite (Na20.Al203.6Si02) and nepheline (Na20. AI203.2Si02), it is more likely that it is due to further but limited reaction between the oxides and fiuoroaluminates.

Jan 1, 1972

Techniques Used and Problems Encountered in Normal and Reverse Circulation Drilling at the Mt Roseby Project, Cloncurry, North West Queensland

Sep 13, 2010

By Kim Le Roux

Cemented paste backfill (CPB) is a relatively new material that is increasingly being used in open stope mining across the world. The advantages offered by this high density tailings backfill include: a lower total cost associated with backfill placement, reduction of excess water underground; and the elimination of the need to process the tailings prior to placement. However, almost all backfill design is based on the performance of laboratory prepared samples since it is difficult to obtain undisturbed samples and conduct in situ testing due to the lack of access to backfilled stopes and the safety concerns in accessible areas. The logistical problems associated with conducting in situ testing and obtaining undisturbed samples of cemented paste backfill (CPB) has lead to the reliance in the mining industry on performance data obtained from laboratory prepared CPB samples. The degree to which these laboratory prepared samples represent the actual in situ condition is not well defined, partly because the influence of the mixing, transport and placement process on the material properties it is not well understood. Therefore, there is a need in the industry to understand how the material properties and hence the performance of the laboratory prepared CPB compares with in situ material. This paper reports the findings of an investigation into the in situ properties of CPB at a gold mine in Northern Ontario. A combination of in situ and laboratory testing, conducted on undisturbed samples, was used to quantify the in situ properties and performance of the CPB. These results were then compared to those of a laboratory based investigation of the same CPB. It is evident from this investigation that the bulk properties of the in situ CPB are different from those of the laboratory prepared CPB. The most significant observed differences are that the in situ CPB has a higher void ratio and a lower degree of saturation than the laboratory prepared material. The implication of these differences on the stability and performance of the CPB will also be explored in this paper. 1

May 1, 2002

By Y Xie, L O’Connor, S C. Dominy

Sheeted vein gold deposits are characterised by multiple subparallel veins and often free milling gold. Variability in gold grade and recovery parameters are enhanced by poorly designed sampling and test work protocols. Poor quality samples generally equate to an enhanced nugget effect. A sample can be described as being representative when it results in acceptable levels of bias and precision. Total sampling variability can be quantified by the relative sampling variance, which measures the total empirical sampling variance influenced by the heterogeneity of the lot being sampled under the current sampling / test work protocol. Effort should be made to minimise the relative sampling variance through Theory of Sampling (TOS) and quality assurance / quality control (QA/QC) application. This contribution reports on a case study that exemplifies how high-quality grade and recovery data can be gained from a well-designed and planned drilling, sampling and test work program, followed by bulk sampling. Results across historical resource drilling, geometallurgical drilling, laboratory assay / test work, geometallurgical modelling and a bulk sampling/pilot processing study are reconciled. A whole core, entire-sample test work protocol was used to acquire fit-for-purpose gold grade and recovery data for inclusion into a Pre Feasibility Study reported in accordance with the JORC Code.CITATION:Dominy, S C, O’Connor, L, Xie, Y and Glass, H J, 2017. Geometallurgical sampling protocol validation by bulk sampling in a sheeted vein gold deposit, in Proceedings Eighth World Conference on Sampling and Blending , pp 185–196 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017