Search Documents

By G. W. Jones

During the course of an investigation by the Bureau of Mines into the causes, behavior, end control of anthracite-line fires, it was observed that the carbon monoxide disappeared from a scaled fire area much more rapidly than could be explained oil the basis of leakage of gases. Two suggestions were offered for this high rate of disappearance; (1) That the carbon monoxide was oxidized at temperatures below 150° C, by either the anthracite or its ash (tests on many anthracites have shown that at temperatures above 150° C carbon monoxide is liberated in the oxidation products when air is passed through it); (2) that the carbon monoxide was oxidized by micro-organisms present in the sealed area.

Jan 1, 1939

By Karl R. Becker

A variety of commercial detonators (fuse type and electric instantaneous and delay types) were subjected to impact and thermal stimuli to determine initiation stimulus levels and the dominant parameters in resistance to initiation. In the impact trials the detonators were impacted along their length to find the most sensitive region; threshold initiation limits obtained for these regions ranged from 3.47 to 20.82 joules (2.6 to 15.4 ft-lb). The friction sensitivity of the explosive component was an important parameter in determining sensitivity; various construction features of nonexplosive components played a role as well. In the thermal sensitivity trials, the detonators were heated from ambient to 100° C at an average rate of about 1.0° C/min, and thereafter at 0.5° C/min until they exploded; the explosion temperatures observed ranged from 121° to 188° C. These temperatures correlated quite well with the reaction temperatures of certain characteristic explosive components used by different manufacturers. The data also indicated an effect of confinement on explosion temperatures of detonators.

Jan 1, 1975

By Tony Brunger, Abid O. Adekunte, George Munteanu, David Greentree

A number of novel solutions have been proposed in recent years as alternatives to props and tie-backs in deep excavation support e.g. Adekunte (2008), Deschamps et. al. (2008), Adekunte et al. (2010) and Adekunte (2014). A number of these non-standard restraining solutions involve the construction of permanent or temporary vertical or raking buttress piles that are rigidly connected to the excavation support wall at regular intervals along the wall run. This paper chiefly focuses on the design and construction of twin-vertical buttress piles as restraining systems behind or in front of embedded retaining walls. The system essentially relies on the push-pull mechanism that develops between the twin piles, to maintain the overall stability of the excavation support. The paper’s main areas of concentration include; finite element modelling, geostructural design, construction procedure, instrumentation and monitoring that are associated with the application of twin- buttress pile systems. These are supported with project details of three recently completed high-end luxurious residential developments in Greater London, England, on which the twin-buttress pile system was used to restrain the excavation support walls for the basements on the sites. The mode of application of the system varies across the three sites. While the system was adopted as a long term solution behind the retaining wall on one of the sites, it was designed and constructed for temporary use in front of the retaining walls on the other two sites. Instrumentation and monitoring results from all the sites show the non-traditional system to be safe and effective, whilst having significant beneficial effects on construction programme, sequence of works and project cost.

Jan 1, 2018

By William Reininger

Microtunneling provides a necessary solution for multiple utility crossings associated with the New York Metropolitan Transportation Authority Capital Construction Company?s (MTACC) Eastside Access Project for the Long Island Rail Road. Construction of four TBM tunnels and their approach structures at the eastern end of the project in Sunnyside, Queens required significant modification and expansion of the railroad infrastructure at this location. Maintenance of railroad traffic during project construction is a principal requirement. As a consequence fourteen (14) utility crossing segments are being installed under active traffic by microtunneling methods. Microtunnels were installed in a variety of conditions including depths, types of soils and construction restraints.

By R. Rampersadh

Paper written on project work carried out in partial fulfilment of B Eng (Metallurgical Engineering) degree Steel was sampled after calcium treatment, to follow changes in inclusion composition during the processing of alumium-killed steel into continuously-cast billets, at Mittal Vereeniging. There is some shift in the distribution of inclusion compositions towards alumina, as the liquid steel moves from the ladle to the tundish. This shift may reflect some reoxidation. However, the effect on inclusion modification is small, since only a small fraction of the tundish oxide inclusions is fully solid?which agrees with the plant observation that these heats cast without clogging. Magnesium oxide in the inclusions contributes to liquid formation, substantially increasing the range of lime: alumina ratios over which the inclusions are partially or fully liquid.

Jan 1, 2006

By Stephen A. Gasiorowski, Frank J. Hrach, James D. Bittner

Separation Technologies, LLC (ST) has developed a processing system based on triboelectric charging and electrostatic separation that provides the mineral processing industry a means to beneficiate fine materials with an entirely dry technology. The environmentally friendly process can eliminate wet processing and required drying of the final material. The process requires little if any pre-treatment of the material other than grinding and operates at high capacity - up to 40 tonnes per hour by a compact machine. Energy consumption is low, approximately 1 kWh/tonne of material processed. Since the only potential emission of the process is dust, permitting is typically relatively easy. In contrast to the other available electrostatic separation processes that are typically limited to particles greater than 75 µm in size, the ST belt separator is ideally suited for separation of very fine (<1 µm) to moderately coarse (500 µm) materials with very high throughputs. The triboelectric particle charging is effective for a wide range of materials and only requires particle-particle contact. The small gap, high electric field, counter-current flow, vigorous particle-particle agitation and self-cleaning action of the belt on the electrodes are the critical features of the ST separator. The high efficiency multi-stage separation through charging / recharging and internal recycle results in far superior separations and is effective on fine materials that cannot be separated at all by the conventional electrostatic techniques. Since 1995, this triboelectric process has been extensively used for the beneficiation of coal fly ash with eighteen separators in place and over 100 machine-years of operation at locations in North America and Europe. The technology has been also successfully applied to the beneficiation of a variety of minerals including calcium carbonates, talc, and potash.

Jan 1, 2012

By F. L. Wideman

This paper is one of a series on mining methods being published by the Bureau of Mines. It describes briefly mining practices at the Sunrise iron mine of the Colorado Fuel & Iron Corp., Platte County, Wyo. The Sunrise mine is in the Hartville iron district in east-central Wyoming (fig. 1). The district covers part of the Hartville Mountains, a region of moderate relief in which erosional features have been formed by the dissection of a low plateau. Altitudes vary from 4,300 feet along the North Platte River to 6,000 feet in the uplift. The climate is semiarid, with hot summers and winter temperatures below zero for short periods. Grasses, cacti, yucca, and low desert shrubs grow at lower elevations. Cottonwood and boxelder trees and willows grow along permanent streams; juniper and coniferous trees are confined to the higher elevations.

Jan 1, 1956

Reports by researchers in government, industry, and universities of the United States are given for various projects on basic coal research concerning, the metamorphism, physical and chemical properties, and reactions of coal, and how many of these studies can lead to better utilization of coal.

Jan 1, 1968

By A. Hotta

Reduction of CO2 emissions is the key driving force behind the development and implementation of new solutions for energy production. One solution is circulating fluidized bed (CFB) combustion technology combined with a high-efficiency once-through water-steam cycle. Foster Wheeler&apos;s CFB technology is today commercially available in capacities up to 800 MWe with ultra-supercritical steam parameters. Simultaneously, the Flexi-Burn® CFB technology is being developed to provide capability of flexible operation in air firing and oxy-combustion for carbon capture. CFB technology can offer an attractive solution for the reduction of CO2 emissions, owing to advantages such as fuel flexibility and low emissions that the air-fired CFB technology offers today. Pilot test facilities provide information about the performance of CFB oxy-combustion technology, and the acquired knowledge is being incorporated in boiler modelling and design tools. One of the European R&D initiatives on carbon capture and storage (CCS) is the Technological Centre for CO2 Capture and Transport, which is supported by the Spanish Government through the Fundación Ciudad de la Energía (CIUDEN). CIUDEN is a research and development institution created by the Spanish administration in 2006 and fully conceived for collaborative research in CO2 capture, transportation, and storage. The Technology Development Centre for CO2 Capture and Transport comprises two technologies on oxy-combustion: pulverized coal (PC) and circulating fluidized bed (CFB). This paper will focus on the design and main characteristics of the 30 megawatt-hour thermal capacity (MWth) oxy-CFB boiler. Foster Wheeler is the technology provider of the Flexi-Burn CFB unit, for which commissioning has been completed in the first quarter of 2011. The CFB unit design allows operation either under conven¬tional combustion with air or under oxy-fuel conditions. The size of this experimental boiler is sufficient to allow the scaling of the results to commercial units. In this way, multiple fuels and operating conditions can be tested economically. The results will validate the design of a future 330 MWe supercritical Oxy-Combustion Power Station (OXY-CFB-300 Compostilla Project) intended to demonstrate the CCS technology at commercial scale. The Compostilla OXY-CFB-300 Project is one of the six CCS demonstration projects funded under the European Energy Programme for Recovery (EEPR) of the EU. The project is based on a future 330 MWe CFB supercritical oxy-combustion plant, with CO2 storage in a deep geological formation. The first phase of the project, granted by the EEPR programme and led by the Spanish utility ENDESA, includes all studies and characterization work needed on CO2 capture, transport, and storage, as well the costs, financing, and regulatory and permitting required, prior to the final investment decision for the construction phase of the plant by the end of 2012.

Jan 1, 2012

By Peter Moser, A. Gaich, E. Grasedieck Zechmann

In The SMX Blast Controller is a novel tool for precisely controlling the geometry of a blast based on the technology of 3D imaging. It enables to derive precise information about the geometry of the face of a bench in a quarry from a pair of stereoscopic images taken from the bottom level of a bench with a calibrated standard digital camera. Apart from staking out the blast position with delimiters that mark the area to blast and taking then two images (freely), no further actions are required which allows performing the data acquisition without requiring any surveying skills. The 3D image generation and blast planning does not require special computer. It is estimated, that every blast foremen is able to work with the system after a one-day training as the system includes a high grade on automatism. The software package allows the blast foreman to design and stake out a blast, based on provided geometric values, such as burden, side spacing, hole inclination, sub-drilling, row number & distance and drilling pattern. The software connects these values with the 3D information acquired by the digital images. All the drill & blast information can be used also for blast documentation. The SMX Blast Controller overcomes also the problem of doing the back transfer from maps derived by surveying into nature as the resulting 3D image and all the information associated to it (hole position, etc.) can be correlated with the nature by visual comparison and the help of a single reference line, defined by two points. The system is designed to be used also in small to medium quarries. It can help, that the control of the geometry of the bench face and the precise design of the charge of the blast on a borehole per borehole basis will become an accepted daily routine.

Jan 1, 2006

By G. S. Scott

In the course of the Bureau of Mines investigation relative to the causes, behavior, and control f anthracite-mine fires, attention was directed toward the correlation between the temperature of oxidation and the gaseous oxidation products in the range of temperatures between 100° and 350°C4/ These tests, made on a high-grade anthracite to determine the amount of oxygen consumed and the amounts of carbon dioxide, carbon monoxide, hydrogen and methane evolved when air was passed through samples of the anthracite at various elevated temperatures, showed that the gases evolved and their relative proportions vary with temperature, constitute a means for determining the probable temperature of the anthracite, and thus permit detection of incipient heating before a dangerous fire hazard exists. As the relationships mentioned are affected somewhat by the amount of previous oxidation of the coal, it was deemed desirable to know to what extent they might vary owing to this cause. It was also considered desirable to have a means for estimating the extent of oxidation from the gas analysis, as this would permit a more accurate estimate of probable temperature. Finally, it seemed desirable to know how much the composition of coal might vary over an extended period of oxidation, since this was previously suggested5/ as a possible means for estimating the probable maximum oxidation temperature to which a sample of coal had been subjected.

Jan 1, 1940

At a regional scale, the Otago Schist has been divided into textural zones, metamorphic zones, structural transposition zones, and terranes and lithologic associations. Each of these subdivisions reveals aspects of the internal structure of the lithologically monotonous Otago Schist but, to date, a map of the schist derived directly from structural data has not been made. In the present study, digitised structural data from the QMAP GIS were used to make a form line map of Schist foliation which, in turn (and using certain non-unique guiding assumptions), was used to construct a provisional foliation thickness map of the Otago Schist. Contours of dominant foliation (Sp) thickness have been drawn from 4 kIn above to 16 km below the reference level of the Caples-Torlesse terrane boundary in the schist structural pile. A recent revision of the Otago Schist textural zone classification has shown that the grain size of metamorphic white micas increases progressively with textural grade. There also appears to be a correlation between schist mica grain size and foliation thickness. Using mica grain size, it may eventually be feasible to establish the vertical structural position of samples in greenschist facies parts of the schist pile to a precision of ¦ 1 km or better, even if they are in inliers or fault-bounded blocks. Foliation thickness and mica grain size are thus potentially useful tools for research and exploration in the Otago Schist in that they assist with structural interpolation and extrapolation. Even at this early stage of application they can be used to provide hitherto unobtainable, semi-quantitative estimates of displacement on Mesozoic and Cenozoic faults and folds. &nbsp;

Jan 1, 2001

By A. S. Macfarlane

The South African Institute of Mining and Metallurgy was approached by the Australian Institute of Mining and Metallurgy to present a paper on the current practice in terms of the valuation of mineral projects and properties, given the development of a Code for the Valuation of Mineral Properties, developed in Australia (the VALMIN Code), and a similar Code in Canada (the CIMVal Code).This paper is the result of research and investigation into the matter, in terms of the reporting of Mineral Resources and Reserves, financial reporting practice, the Listing Rules of the Johannesburg Securities Exchange, and various practices in valuation. The paper establishes that a strong linkage has already been established between the SAMREC Code for the reporting of Mineral Resources and Reserves and the Listing Rules, and that, for completeness, a Code for Valuation needs to be developed. This Code will be similar to its international counterparts, with the necessary inclusions which are relevant to South Africa, and will provide guidelines and definitions on matters such as transparency, materiality and competency in valuation. It proposes that a multi-stakeholder steering committee be established under the auspices of the SAIMM, to deliberate and design a process for establishing such a Code.

Jan 1, 2002

To be able to continuously monitor the noise to which underground workers are exposed as a better way to help prevent hearing damage. The Approach: The Bureau of Mines has developed a Time-Resolved Audio Dosimeter which can be worn by miners to record noise level every 30 seconds and store It in a miniature solid state memory. Figure 1 is a photo of the dosimeter. [ ] How It Works: Acoustical noise is picked up by a micro-phone and fed to a sound level meter which produces a d-c voltage proportional to the A-weighted sound pressure level. (As specified by federal regulations, the A-weighted sound pres-sure level approximates the response of the ear by discounting the higher and lower frequency components of the noise.) This d-c voltage controls an oscillator which, together with related circuitry, produces a pulse train having a frequency that&apos;s proportional to the noise level.

Jan 1, 1975

By E. S. Leaver

The gold that is not recovered by a particular process is refractory to that process. A study to determine how the refractory gold is associated in the ore constituents usually indicates the needed improvement in the process or additional methods for bettering recovery. In preliminary work, segregation of the various minerals, gangue or impurities, and data showing the reactions of each in the recovery method readily confines the refractory gold to a certain part on which extensive research can be directed. In this dissecting plan, the microscope is an important aid in locating the refractory gold but should be supplemented by chemical tests.

Jan 1, 1934

By Steve Kral

A few months ago, Congress passed, and President Bush signed, a national energy bill. Designed to decrease the nation’s dependence on foreign sources of energy, the bill earmarked several billion dollars to increase the use of U.S. coal reserves. The bill also modified permitting regulations to speed up development of the coal reserves located on federal land. Coal currently supplies more than half of the nation’s electricity needs. And as housing starts continue to in-crease and with the nation’s appetite for electronic gadgetry, the demand for energy in the United States will only go up. That means coal producers must expand production while at the same time containing costs so they can enjoy this period of improved coal prices.

Jan 1, 2005

By Bob Hannah, Peter C. Hayes

The changes that are happening in the world of metallurgy, and with it university education, are generational and require generational responses. Some of the key issues facing metallurgical education and ongoing professional training are explored. What will be required of metallurgical engineering professionals in the coming decades? What knowledge and skills will be needed? How to provide the educational and learning pathways, and how to attract smart young people into this profession? These are issues more readily addressed by tertiary institutions in conjunction with industry; perhaps the greater challenges lie in building and maintaining competencies post-graduation. There is a need to establish and maintain a system that supports graduates and enables them to develop further into competent expert engineers able to successfully address complex engineering challenges.

Jan 1, 2014

By Arif Emre Dursun

The aim of this study is to present hazard classifications of location, type, and causes of accidents in Turkish coal-extracting industries using Analytic Hierarchy Process (AHP). In this study, fatal mine accidents were analyzed by pairwise comparison and weighting, and the most important hazards were identified by determining the effective main and sub-criteria among location, type, and causes of accidents. For this purpose, 1st, 2nd, and 3rd level hazards consisting of location, type, and causes of accident were determined by using the data of fatal mine accidents in underground and open-pit coal mining in Turkey between the years of 2010 and 2020. And then the data were categorized, and each category was prioritized using the AHP technique. According to the weights calculated by AHP, the most dangerous main criteria at 1st level hazards in underground coal mining is ventilation operations (0.363), while the most dangerous sub-criterion at 2nd level hazards is firedamp explosions and other gas accidents (0.409). On the other hand, in open-pit coal mining, the most dangerous main criteria at 1st level hazards are slopes and benches (0.575), while the most dangerous sub-criterion at 2nd level hazards are landslides (0.429).

Dec 30, 2023

By Enrique Garay

Actualmente el geólogo de mina toma información rutinaria, mapea los bancos de la mina, los taladros para voladura y loguea los núcleos de perforación y fragmentos del aire reverso. Para la localización en el campo utiliza un GPS que tiene una estación en tierra que permite triangular en tiempo real. En ese sentido, el presente texto señala la importancia de la función del geólogo y las herramientas de campo que utiliza para la exploración y la definición del modelo geológico en la mina Pierina. Así para la digitalización del mapeo geológico utiliza el programa AutoCad, en el caso de mapeo de taladros para voladura emplea un Colector de Datos que posee una hoja de calculo que permite recoger datos del tipo de alteración, porcentaje de arcillas, dureza y tipo de mineralización. Finalmente, la información que genera el geólogo de mina es útil para diferentes usuarios ya que sirve para mejorar el cálculo de reservas, manejar el control eficiente del minado de mineral y desmonte, así como generar el soporte geológico a los geotecnistas responsables del estudio de estabilidad de taludes del tajo abierto, así como desde el punto de vista ambiental es posible definir zonas con potencial de generar drenaje ácido de rocas.

Aug 25, 2002

By R. S. Dean

[In E;encralt the I~8:al:ul&apos;,~,C,-J. Div:&apos;sion conducts in\&apos;8stigations relat-ing to the treatment of OrGR o.nd L!\3tallurl..&apos;"lcal prod tctR froJ] t~e condi tion in :hich they are Itinod to t!1e refi!l(,u r.etal, . &apos; th &apos;the ob,icct of conserving natmal&apos; resources .e..nd 81:mir..3.tin~ wacte by furn.i:::hir..g :nforInf&apos;_tiou on current methods of metal11:.rgical practice, Tfu&apos;..:.kir..g fund T!l;ntal .;;.otudie&apos;" of metal-lurgical processe~, and de~eloping ~e~ proc6sses O~Q lloys to the point of dewonctrati:r:g the:&apos;..r practicab&apos;lity or va.lue}

Jan 1, 1941