Search Documents

By Yogesh Prashar

Three conventional uplift tests and 12 Rapid Pile Load Tests (RLT) were performed on total of fifteen 16-inch square pre-cast concrete driven piles at a test site in Emeryville California in December of 2000. The uplift tests were performed in accordance with ASTM standards, and the RLTs were performed using a FUNDEX RLT. The RLT is carried out by dropping a mass of 25-tons on top of the pile, thereby inducing a force that is measured by a load cell. An optical lens records the vertical deflection of LED's that are mounted on the pile. Ultimate uplift and compression capacities of each of the fifteen piles were determined using the Davisson method. Soil parameters were calibrated by back-calculation (cohesion and internal angle of friction) using both the results of conventional uplift load versus deflection curve, as well as the results of the triaxial compression tests. A two-dimensional finite difference model including soil elements, and structural elements representing the test pile was setup using the computer program Fast Lagrangian Analysis of Continua (FLAC). FLAC was used to simulate both the uplift as well as the RLT. Strength increase of cohesive material was also accounted for in the analysis. Numerically simulated and theoretically computed pile capacity curves and axial deformation variation with applied load curves are in close agreement to the observed curve during the field test. Conclusions are made from this test site regarding the factors influencing results of RLT.

Jan 1, 2002

By M. R. J. Wyllie, Michael A. Torcaso

With the continued deep drilling of today, increasing numbers of high pressure and high temperature gas-condensate reservoirs are being discovered. Correspondingly, the ranges of properties of gas-condensate reservoir fluids are also being increased. The literature1*'." contains several excellent reviews of the property ranges in presently known condensate reservoirs. When one examines these property ranges, it becomes apparent that the need for reliable data is great if the engineer is to evaluate properly or appraise a gas-condensate reservoir. It is the purpose of this paper to present phase-behavior data that will point out some of the important variables that influence recovery from gas-condensate reservoirs produced by pressure depletion. All these variables may be resolved into two major categories: the hydroc:arbon composition of the reservoir fluid and the physical properties of the reservoir. But the variables which we will consider are those which are usually determined from well tests shortly after discovery and are, consequently, readily available to the engineer. They are as follows: (1) the producing separator gas-stock-tank liquid ratio, (2) stock-tank liquid gravity, and (3) reservoir temperature. Laboratory depletion studies have been performed on several reservoir fluids to illustrate the effect of changes in the cronsidered variables upon ultimate recoveries. The deviation factors, Z, of a series of reservoir fluids were determined experimentally to illustrate their order of magnitude and their effect upon the calculation of in-place reserves existing at high pressurcs and temperatures. The procedures followed in conjunction with the performance of these studies and their associated calculations are illustrated in Fig. 1. For the purpose of this paper, the depletion recoveries are expressed only in terms of pcr cent of initial stock-tank liquid, with the abandonment pressure assumed to be 500 psig. VARIATION OF RECOVERY WITH INITIAL PRODUCING SEPARATOR GAS-STOCK-TANK LIQUID RATIO The producing separator gas-stock-tank liquid ratio has long been one of the principal criteria in assumptions and generalized correlations' used for the estimation of ultimate recovery from gas-condensate reservoirs. Fig. 2 presents a plot of the cumulative recovery of stock-tank liquid at abandonment as a function of the initial producing separator gas-stock-tank liquid ratio. The graphical illustration represents the results of 44 laboratory depletion studies performed on actual gas-condensate fluids. These data are presented not only to illustrate the general trend of ultimate recovery increase with initial producing ratio increase but to emphasize the considerable variation in possible recovery at any given producing ratio. Table 1 presents the properties of two actual reservoir fluids chosen to illustrate the approximate extremities of producing ratios for gas-condensate systems. The fluids designated as A and B exhibited initial producing ratios of 3,400 and 114,000 scf/bbl, respectively. Fig. 3 presents a graphical comparison of the cumulative stock-tank liquid recoveries, calculated from the well-stream compositions and produced volumes for each fluid during depletion. It is to be noted that Fluid A exhibited a recovery of only 16.5 per cent when produced to an assumed abandonment pressure of 500 psig while the corresponding recovery for Fluid B was calculated to be 62.2 per cent. This difference in recovery, which exemplifies the general trend of recovery increase with initial producing ratio increase, is readily explained by consid-

By M. A. Trevits, T. A. Gray, L. M. Crayne, P. Glogowski

Mine seals can he remotely constructed in underground coal mines through vertical boreholes when direct access to a fire is impossible or considered to he too dangerous. This method has great merit because the boreholes can be drilled to specific mine areas, and the seals can be positioned close to a fire zone. The technology however can be largely ineffective if the constructed seals do not provide of effective barriers to airflow or if they cannot he used to impound water and other inert materials. Unfortunately, no viable alternatives exists to sealing the entire mine to the ground surface. Full-scale remote mine seal construction research is being conducted at the National Institute for Occupational Safety and Health (NIOSH) Lake Lynn Laboratory (LLL). Under this effort. Howard Concrete Pumping Company and GAI Consultants Inc. have joined forces to evaluate a potentially significant improvement to the current state of the art. This paper covers the development o f novel technology or rewrote mine seal construction, the evaluation of rite materials used, the construction practice and the Fellow-up testing.

Consents Required for Overseas Persons Overseas Investment Regulations 1974 Foreign investment proposals must be reviewed by the Overseas Investment Commission to ensure that these are in accord with national interests. Consent must be obtained from the Commission for: 1. New investment proposals which include: a. An overseas person acquiring 25 per cent or more of any class of share in a company. b. A New Zealand company issuing shares to an overseas person where this will result in that person owning 25 per cent or more of the company. c. An overseas person acquiring business assets for consideration in excess of $100 000. d. An overseas person commencing business in New Zealand. 2. Borrowing in New Zealand: An overseas person must obtain consent to raise funds in excess of $300 000 in New Zealand. 3. Borrowing Overseas: New Zealand incorporated companies must obtain consent to borrow overseas. Current policy is borrowing will be approved where the loan is for a specified fixed term of one year or more.

Jan 1, 1982

By J. Daavittila

In the latter part of the 1980s Outokumpu Chrome in Tornio, Finland, was in a situation when its twenty-year-old ferrochrome plant was becoming too inefficient to sustain economically sound production. The company made extensive studies on the then available processing methods to find out the best possible processing route. As a result, the whole plant was practically rebuilt and expanded. When equipment was proven in practical operation, an application for FeMn production was developed. Now as the Tornio FeCr-plant is considering expansion, the same type of exercise is to be performed with today?s challenges, which will be discussed in the paper. These challenges include increasing costs or decreasing quality of raw materials, increasing energy costs, stricter environmental regulations and demand for better working conditions. The possibilities of resolving to these challenges will be discussed in the paper. The future and continuing development with FeCr includes the better utilization of process dusts and a lower consumption of energy. By adapting the latest automation tools to better control the process, even higher efficiencies can be achieved with present technology. New processes are considered for development in the future and some possible technologies will be described.

Jan 1, 2004

By Nobuzwe Makhotla, Sasha Boskovic, Steve Hearn

"Mineral separation efficiency in flotation depends, to an extent, on the type of frother used. Huntsman develops and manufactures unique frothers which are suited for mineral processing applications. This paper discusses the Huntsman approach to understanding the industry’s flotation frother requirements to optimise frother selection and introduce the Huntsman’s POLYFROTH® frother range. Specific case studies where the frothers are used are discussed. INTRODUCTION Froth flotation is a process of using bubbles to separate minerals based on their relative affinity for water. Bubbles are induced in the slurry through aeration. Chemistry is used to aid the flotation process and chemical reagents are added to enhance the separation process. The flotation reagents include frothers, collectors, surface modifiers and pH regulators that control physical and chemical conditions of solid, air and liquid phases, respectively. As described by Harris (1976), the key effect is that of bubble size control by way of preservation of the generated bubble size, which is attributed to the coalescence inhibition by the presence of the frother on the bubble surface. Following this, the frother must stabilize the froth phase. Frothers are also added to create optimal conditions for bubble creation and stability by decreasing the surface tension of the water. Depressants may be added, depending on the ore treated, to assist the hydrophilic particles to stay in the water phase. Clay particles may need to be dispersed to prevent them from attaching to the bubbles. Hydrophobic particles attach to the bubbles and are carried to the surface of the slurry where froth is formed. It is important for these bubbles to have the mobility to carry the mineral to the launder where the concentrate is collected. Types of Frothers There are generally three main groups of frothers used in froth flotation. Alcohol Type These frothers have a molecular structure that usually includes 5 to 8 carbon atoms in a hydrocarbon chain and their solubility in water is limited. Methyl isobutyl carbinol (MIBC) belongs to this category and is widely used in the industry. The weaker alcohol-type frothers are more selective and typically suited to finer particles. There are three sub-categories under this group: aliphatic, cyclic and aromatic alcohols."

Jan 1, 2015

By J L. Mauk

The Martha epithermal Au-Ag deposit contains multiple generations of quartz veins with a range of textures. We examined: +        vein textures, +        crosscutting vein relationships, and +        the paragenetic sequence within the pit walls as well as a wide range of hand specimens. Samples include host rock, breccia, and veins, but these groups are not distinct; instead, they form a continuum.   Veins at Martha mine show a wide range of textures on a local scale; these textures also change significantly over both the lateral and vertical extent of the pit. Common textures include crustiform bands, comb quartz, colloform bands, platy quartz, massive quartz, drusy quartz, sedimentary textures and brecciation.   Vein grades relate to textures. Many textures, including crustiform, platy, cherty, and sedimentary textures display predominantly low grades, but some textures are linked with high grades, such as ginguro, massive and comb quartz where they are associated with visible base metal sulphides and/or electrum. Host rocks and most breccias are low grade, as most samples contain <2 ppm Au.

Jan 1, 2006

By M. C. Bhulose

Paper written on project work carried out in partial fulfilment of B. Eng (Mining Engineering) degree The purpose of this project was to identify constraints that could occur in the current sub-decline shaft at Turffontein Shaft should an increase in production take place. Particular attention was to be paid to the transportation of men and materials and to the broken rock and ventilation capacity of the shaft. This project is an in-depth evaluation of the logistic capacity of the sub-decline system at Turffontein Shaft in order to determine by how much production can be increased in this area to replace tonnages from the vertical shaft area, where ore reserves are rapidly becoming depleted.

Jan 1, 2004

By H. Saroglou

The anisotropic behaviour of Athens Schist has been brought out through the testing of specimens with varying orientation of schistosity with respect to the major principal stress under uniaxial, triaxial and dynamic conditions. A large number of results from tests on intact rock specimens of the Athens Schist were statistically analysed and evaluated.

Jan 1, 2004

By P. J. N. Pells

A good thing is becoming a bad thing. Rock mass classification systems, that are so excellent for communications between engineers and geologists, and that can be valuable in categorizing project experience, are emasculating engineering geology and rock mechanics. Some engineering geologists have been sucked into thinking that Q and RMR values are all that is needed for engineering purposes, and seem to have put aside what can be learned from structural geology and geomorphology. Many rock mechanics engineers seem to have forgotten the scientific method. This paper attempts to redress the situation by showing how mechanics can be used in rock engineering to design with a similar rigour to that used in the fields of structural engineering, hydraulics and soil mechanics. It also attempts to remind practitioners of what can be achieved by skilled engineering geology.

Jan 1, 2008

By J. Baird

The Sappington Bridge, a steel arch span bridge constructed in 1904 over the Meramec River, was demolished due to its advanced state of deterioration. The demolition was a project to benefit Crawford County, Missouri, the U.S. Army, the Missouri Department of Transportation, and the University of Missouri – Rolla (UMR) was conducted jointly by the UMR Rock Mechanics and Explosives Research Center (RMERC) and the UMR Center for Infrastructure Engineering Studies (CIES). By arrangement with Crawford County, a 55-foot span of the old bridge was brought to the University Structures Laboratory in Rolla, while the longer, 200-foot span of the bridge was demolished using preburning and explosives. Originally, the longer span was to be blown up by C Company of the 5th Engineer Battalion (from Ft. Leonard Wood, Missouri) under the supervision of personnel from UMR. Unfortunately, permission for the operation from the Department of the Army could not be obtained in time to meet permitting requirements for the demolition. Therefore, a commercial demolition contractor was employed to perform the demolition, and to remove the scrap.

Jan 1, 2003

By Eleanor Abshire

[THE INCREASING use of hafnium as a vital component in atomic power reactors has brought this metal into recent prominence. A literature survey was made and this bibliography was compiled to provide research and production groups with a ready source of reference to this important metal anti its compounds. This service is rendered by the Zirconium Information Center, which is sponsored by the Department of the Navy, Bureau of Ships, and the F .S. Department of the Interior, Bureau of Mines, tit the Bureau's Northwest Electrodevelopment Experiment Station, Albany, Oreg. The following reference sources have been reviewed for this compilation : Chemical Abstracts; Industrial Arts Index; Crerar Metals Abstracts; Nuclear Sciences Abstracts; Bureau of Mine; Information Cicular 7771, Bibliography of Zirconium; anal Bureau of Mint' Information Circular 7830, Bibliography of Zirconium, suppllement to Information Circular 7771.]

Jan 1, 1960

By Akira Usui

The details in small-scale variability of the geological occurrence and chemical composition of ferromanganese crusts are not yet well understood, although the northwestern Pacific seamounts are believed to be among the most promising areas for rare metal resources. Our belief is that geological observations and geochemical analyses are still insufficient for economic evaluation or for discussion of depositional processes and environments. Our team, composed of geologists, mineralogists, geochemists, physical engineers, and microbiologists has attempted to utilize an ROV for in-situ measurement and for sampling of undisturbed and uncontaminated ferromanganese crusts at three typical seamounts in the NW Pacific near the Japanese Exclusive Economic Zone. The first ROV geological survey of ferromanganese crusts was successfully completed, and the ROV proved to be the most powerful, efficient and elegant method to date. The collected samples (more than total 1 ton of crusts, at more than 100 sites along a total of approximately 10 km of survey lines) were most suitable to analyze water-depth dependency and secular variation of their composition. The intact surfaces of crusts, collected without the usual abrasion caused by dredging, were also valuable for microbial study of Mn oxidizing bacteria. The ROV sampling devices, however, can be improved with further sophisticated drills or rock saw blades in the future.

Jan 1, 2011

Most types of nuclear power reactors use uranium dioxide fuel. Power reactors using natural uranium dioxide fuel are of special interest to countries such as Australia that have their own uranium supplies. A wide range of uranium dioxide powders can be fabricated and the ideal one flows readily, presses without the need for binders or lubricants, sinters to the required density and gives low reject rates at all fabrication stages. Sinterable uranium dioxide is usually produced via the ammonium diuranate route.The Australian Atomic Energy Commission is aiming to demonstrate production of nuclear grade uranium dioxide from Australian concentrates, improving technology where possible. Details are given of the dissolution, solvent extraction, precipitation, filtration, drying, and· calcination-reduction steps. Solvent extraction from sulphate media is also under study with a view to developing a process to produce a nuclear grade product at the mine treatment plant site.

Jan 1, 1970

By D. G. Krige

For the purpose of determining confidence limits for ore grade estimates, an extensive simulated data base was used, which included 1728 ore blocks with ‘actual’ grades and the corresponding estimates based on ordinary and simple kriging. The practical results show that conditional unbiasedness is essential and that acceptable confidence limits can then be set using Normal theory for the simulated error distribution based on the logarithms of the ratios of ‘actuals’/estimates with a variance related to the kriging variance. The mean of the data used to prepare the variogram and the estimated block grade are to be used properly in this approach. A practical analysis was also done of the actual point and block data from a very large mined out Carbon Leader area. The distributions of the actual grades for two levels of block sizes with different levels of variability were fitted using three models, ie. 2-. 3- and compound-lognormal. The trends of tonnages, grades and relative profits for a range of pay limits, as well as the usual tonnage-grade curves, show a practical insensitivity for the choice between the three lognormal models considered.

Jan 1, 2003

By Franz Kolmbauer

At Primetals Technologies Brazil Ltda. Rio de Janeiro Santa Cruz Workshop we electroplate mold coppers for continuous casting by tank plating. Tank plating submerges the copper in the bath of the plating solution. This is the most common method of plating and is applicable for both broadface and narrowface copper plates. Mold copper plates have a decisive impact on the product quality as well as the cost for maintenance and production. A perfect understanding of the operational influences on the plates and performance variables are the first step for the right selection of a copper plating method. Variable Hiper Coat keeps the Copper Plates 50% up to 100% longer in operation because of applying hardness on the Copper Plate where it is needed. Primetals Technologies Brazil provides the solution which meets and exceeds the requirements for todays and future demands.

Aug 16, 2017

By Luis Valle, Fredy Zegarra, Ernesto Vizcardo

El uso de los procesos estocásticos y cadenas de Markov se ha desarrollado solo para estudios de probabilidades en la rama de las ciencias matemáticas y como una opción a las descripciones tradicionales en el campo del procesamiento de minerales, se realizó una comparación entre ambas metodologías para lo cual se cuenta previamente con varios análisis granulométrico proveniente de los molinos de Bolas industriales de la empresa Shougang Perú y pruebas granulometrías de Molienda de Sider-Perú, comparar en ambos estudios, como el probabilístico (Cadenas de Markov) y el cinético (Selección y fractura) ofrecen un buen acercamiento al resultado experimental, dando como una buena alternativa el primero por su uso del manejo estocástico.

Sep 1, 2017

By Marilia S. de Magalhaes

Keywords: sinter, characterization, agglomeration, iron ore Iron ore sinters are the main burden of blast furnaces for pig iron production. The evaluation of these agglomerates is very important due to their properties affect indirectly the productivity and costs of production of the steel industry. In the sintering plants, the standard procedure of sinter assessment has been carried out by particle size control, bulk chemical analyses, tumbler and/or shatter tests and determination of reduction degradation and reducibility indexes. Microscopy techniques have just been applied to characterize sinters produced in pilot conditions, however, these techniques, the classical ones and the less traditional, allow enhancing the industrial sintering process assessment. For investigation of the phases, microstructures and fabric, reflected-light and scanning electron microscopy(backscattered electrons images) were used; for micro analytical chemical examination, energy-dispersive X-ray spectrometry; for Kikuchi patterns registers, electron backscattering diffraction. In addition to the microscopy techniques, the magnetic behavior was depicted by means of magnetic susceptibility measurements. Iron ore sinters are made up by hematite, magnetite, silicoferrite of calcium and aluminium and silicates. These phases develop either during sintering or, in some proportion, represent remnants of ores and fluxes; this is the case of some hematite and Mg-bearing silicate, respectively. From the magnetic susceptibility results, three different behaviors were determined, which are directly related to the magnetiteproportion in the samples. The phase association and proportion, the sintering conditions andthe quality assessment are some features appraised by such procedures, which reveal themagnitude of this proposal in sintering plants.

Jan 1, 2005

By Casey Erickson

Goldstrike Property ??Located in Elko, NV USA?Carlin Trend ??Mining Since 1985 ??27 Million Ounces of Gold Mined ??Production of 400,000 tons/day ??1,600 Employees

May 1, 2011

By J. L. Holman

The Bureau of Mines, at its Rolla Metallurgy Research Center, has devised methods for separating and reusing the major portion of waste plastics discarded in urban and industrial refuse. Waste plastic concentrates from a local collection drive, recycling center collections, urban refuse pilot plants, and the secondary metals industry were separated into three major thermoplastic families--polyolefins, styrenes, and vinyls--based on differences in density using a Bureau-designed sink-float-elutriation hydraulic separator. Other separation methods and systems such as air classification, jigging, liquid media, screening, and electrostatics were studied. Vinyl plastics contain up to 50 percent HC1. It was found that over 90 percent of the HC1 in vinyls can be recovered as usable hydrochloric acid by pyrolysis at 350° C. The remaining pyrolysis products which had heats of combustion in excess of 12,000 Btu/lb, could become valuable as a future source of energy. A characterization study conducted on eight chopped wire insulation wastes from secondary copper and aluminum processors showed that most wastes contained 2 to 7 percent residual metal and large percentages of vinyl. The residual metal content of some of these wastes was lowered to 0.1 percent and the vinyl portion segregated using various separation techniques. The research also suggests ways in which reclaimed thermoplastics may be fabricated into useful products.

Jan 1, 1974