Search Documents

By J. Bender

The objective of this research was to (1) Further develop cyanobacteria mats' for metal-tolerance and cold-tolerance, (2) test them for durability in the field environment and (3) assess them for metal sequestering potential with actual and simulated field samples. Results show that mats performed well In the field and effectively sequestered metals from actual and simulated field samples. Metal uptake from Iron Mountain Hine samples was for Ins 87%, Cu and Cd 99%, Initial concentrations (mg/L) were Zn = 3,250, Cu , 279, Cd = 28. In solutions simulating the Gulf Tunnel drainage, Zn and Mn were effectively removed by mats immobilized on glass wool. Effluent water, after treatment, generally had a Ph of 7 .5-8.5. Al though the final metal concentrations in the mats 'harvested from the decontaminated water were only 1% or less, the actual mechanism of metal deposit was probably a mat-mediated alteration of the environmental conditions causing the metals to deposit outside the mat as oxides or carbonates. Bioflocculents, released by the mats, were likely involved in the metal-removal process.

Jan 1, 1996

By AIME AIME

WEST TEXAS, New Mexico and Northern Mexico form one of the most interesting regions in America for geologists and mining men and are full of points of historical and human interest for others. Including as the region does, a representative portion of the high plateau of Mexico, the front range of the Rocky Mountains and the great down-dropping plains of Texas, there is variety as well as interest in the geological and mining problems there to be studied. Gold and silver mining were the pioneer industries and are yet of high rank in importance. Among the papers to be presented at the El Paso meeting of the Institute this month will be two dealing with silver mining and ore treatment at the Shafter mine in Texas, that most un- usual property which has for so many years been the largest mining enterprise in its region. West Texas is now better known for its petroleum and gas, and in another paper will be described the problems involved in uding natural gas for smelting at the well-known El Paso smelter of the American Smelting and Refining Co. In still other papers, presented at the session sponsored by the West Texas Geological Society and cooperating organizations, the general geology of the region, the potash and the sulfur deposits will be de- scribed. At El Paso the refineries of the great com- panics will be available for visits.

Jan 1, 1930

By Lyle F. Smith

With the demand for larger diameter raises under all ground conditions and the increasing price of drill rods and operating costs, it was evident that there was a need for a raise borer with a variable-speed drive and fast-response torque limiting control. The raise boring machine described in this paper was developed after several years of market research and discussions with mine operators and construction contractors. This paper discusses the Ingersoll-Rand raise borers with the solid-state controlled DC motor drives. These machines have gained wide acceptance in the five-year period since being placed in operation and are designed to accommodate the range of raise diameters and lengths most required today.

Jan 1, 1978

"When a metal-mining company takes out a workmen's compensation insurance policy, it does so to relieve itself of its uncertain and variable financial liability under laps requiring payment to employees for lost-time accidents, there-by passing the liability or to the insuring agency. For this service, or rather for the assumption of the risk, the insuring agency charges the mining company a price, or in insurance parlance, ""a premium"".The insuring agency depends upon a volume and variety of business to average the losses incurred by its individual policy holders, and determines its price to cover losses that are suffered and its cost of doing business.It is generally known that all types of insurance are founded on the theory of probability applied to large groups of risks, Workmen's compensation insurance is no exception, and the average price paid therefor must be based on the frequency and severity of accidents in the particular industry or branch of industry under consideration. The frequency and severity rates are determined by statistics, which, of course, unless standardized, kept carefully and consistently, and analyzed properly, are liable to be inaccurate and misleadingThe importance of large groups in arriving at an average price for insurance service can not be overestimated, For example the writer knows of one small group of some twenty metal-mining companies whose losses during the past two years exceeded their premium charge by 54%. Not a single individual company during the two years kept its losses below the premium rate. For several years the group as a whole has persistently exceeded its premium rate, Such risks are not profitable to the insuring agencies and can only be carried where a large volume of good risks will balance the poor risks, but in order to conform to good insurance ethics the premium rate must be based on averages for the industry as a whole, and kept sufficiently low to induce operators to sell their risks."

May 1, 1924

By Arunsiva R., Sivaranan S., Venugopal B., Kumaran M.

Being a rapidly developing country, India is undergoing a massive infrastructure phase change remarkably. The construction industry is already set to boom, but the time and space constraints necessitate the employment of heavy plants and machinery to take the foundations deeper than ever. Operating such machinery on soft or poor ground conditions without a good working platform leads to uncertainties with massive loss of men and machinery. Plenty of such cases can be observed on construction sites across the globe. Unfortunately, forming a temporary working platform is given least to no importance in the construction industry, particularly ground engineering. This glitch can only be addressed through standard guidelines or codal recommendations on designing and implementing temporary working platforms issued by regulatory bodies. The present paper highlights the importance of providing the working platform, existing design method for working platforms such as TWf 2019:02 of Temporary Works forum, Building Research Establishment BR470 and a brief discussion on the design and construction of the geosynthetic reinforced working platform with a case study is also included. A pitch has been made on the importance of Indian codes/guidelines for the design and construction of temporary working platforms. These guidelines will ensure the safety of the men and heavy machinery and, in addition, increase the productivity of foundation construction irrespective of weather conditions and also become part of the regular construction scope.

Sep 1, 2022

By Gerald L. Colborne

The major role of financial institutions in the free world in the development of mineral resources is to provide the necessary capital in the form of loans to underwrite the development of these resources by the industry on a stable and continuous basis. This capital provided by the depositors to the bank must be invested in sound projects where the degree of risk is relatively small, the return on the investment is reasonable and the time to retire the loan is of short duration. Money is, therefore, one of the important ingredients along with technology, manpower and an exploitable resource that will provide a sound economic base in this region of development. Canadian banks are similar to banks of other western nations, although each country has some differences in their banking systems. The basic difference between the American and Canadian systems is that the former employs unit banking while the Canadian utilizes the more mobile branch system, which is prohibited or restricted in the United States and some other countries. Canadian banks are the subject of this paper, so, subsequent material will relate to Canadian banks unless indicated otherwise. It will be realized by everyone that the mineral industry is only one area of the economy in which the banks are interested and to cover the subject matter in the time allowed, the topic is restricted to mineral resource development. In Canada this is a vital sector of our economy and before we outline some of the details of financing and services involved in various aspects of mineral development, a review of the Canadian mineral industry is a necessary part of the sequence of presentation. The writer presents this material as a resource engineer advising a major bank in mineral matters, so the presentation may relate more to the financial problems of the developer

Jan 1, 1972

By L. Yuan, J. H. Rowland, D. Bahrami, R. Thomas

Blasting is the main method of production in many non-coal underground mining operations and produces multiple toxic gases as a result. The Mine Safety and Health Administration (MSHA) requires mine operators to measure the level of toxic gases in mines as frequently as necessary to ensure they are below regulatory safety limits. The current practice uses portable gas monitors to check the concentrations of toxic gases after a fixed post-blast time. This paper studies the application of a gas monitoring system in the return entry of a limestone mine to determine a safe re-entry time. The National Institute for Occupational Safety and Health (NIOSH) conducted such a monitoring program in a limestone mine from September 2016 through May 2018. NIOSH/PMRD (Pittsburgh Mining Research Division) is endeavoring to develop workplace solutions to improve detection of and reduce the risk of hazardous conditions. This study showed that the use of gas monitoring in the return air can be a useful tool at the mine operator’s disposal to detect and reduce the risk of hazardous conditions and also to reliably estimate the re-entry time.

By P Navarra, R Kuhne

Dynamic simulation (discrete event simulation) is the preferred methodology to evaluate the impact of dynamic aspects of processing plants on the overall plant capacity. This tool can be used to: identify bottlenecks in the plant,justify upgrade and expansion projects by evaluating their impact, oroptimise maintenance and operating practices without disrupting the operation. Iron Ore Company of Canada's (IOC) pelletising plant is a complex operation because of multiple products, varying equipment capacity and shifting bottlenecks. Furthermore, with extensive capital requirements for projects and long lead times, a high level of confidence in project outcome is required. Therefore, a model of IOC's pelletising plant in Labrador City was constructed in 2007 by a joint IOC and Hatch team. The model includes both operational and metallurgical aspects in order to better capture the complexity of IOC operation. In this paper, the justification, boundaries, and functionality of the model are described. A comparison of simulation results to historical plant operation is given. It is observed that projects have interactions and that the benefits of combined projects are not equal to the combined benefits of the individual projects. Projects can have synergies that result in greater benefits when combined or can have overlapping benefits that result in lower benefits when combined. The power of the proposed modeling exercise lies in the ability to assess the impact of projects on overall performance.

Jan 1, 2009

By AIME AIME

THE following brief description of the main features of the, engineering work was prepared for the use of members of the American Society of Civil Engineers and members of the American Institute of Mining Engineers on the occasion of their visits to the tunnels at the time-of their respective. annual meetings in New York, January and February, 1905. DESCRIPTION. Those portions. of the Pennsylvania Extension into Manhattan and Long Island, lying east of the Terminal Station and west of the East River, have been designated as the " Manhattan ?Cross-town:. Tunnels." They traverse a section of the city second in importance only to the financial district, and one that includes the larger hotels, retail shops and theaters and the residences of many of the best known citizens. Section "D," consisting of twin tunnels for west-bound express and local passenger traffic, lies under Thirty-third Street from a point 400 ft. west of the west line of Sixth Avenue, eastward to the river shaft, situated in the block between Thirty-third and Thirty-fourth Streets east of First Avenue. Beginning at the east end, the tunnels are in separate excavations, leading westward from the subaqueous tubes, on a curve of large radius, gradually closing together until it is found more appropriate to drive them in a single excavation. At a point just west of Second Avenue they reach the tangent, aid from there westward lie directly under Thirty-third Street. At a point about 180 ft. west of the west line of Sixth Avenue, the center concrete-wall between the twin tunnels is omitted, and the excavation somewhat widened to make room for a third storage-track, and the tunnel continues to tile station portal in three-track section. Here reprinted through the courtesy of The United Engineering and Contracting Co. The half-tone blocks used for the illustration of this paper have been kindly supplied by the Chasmer-Winchell Press of New York, Pittsburgh and Cleveland.

Mar 1, 1908

By T. Z. Sehume, J. R. Bunt, J. C. van Dyk, C. A. Strydom

"SynopsisCo-pyrolysis of four biomass samples (hardwood chip, softwood chip, pinewood chip, and sugarcane bagasse) with an inertinite-rich medium rank C South African coal was investigated. Proximate and ultimate analyses of the chars prepared using a heating rate of 10°C/min up to 1100°C in a nitrogen atmosphere were used to compare the properties of the biomass and the coal chars. Similar gross calorific values (28.5–29.1 MJ/kg) for the woody biomass-coal blended chars were observed, which were slightly higher than that of the coal char sample (26.5 MJ/kg). CO2 surface areas of the chars of the woody biomass samples (328.1–329.4 m2/g) and of the blends (238.5–271.5 m2/g) were higher than that of the coal char sample (94.2 m2/g). Thermogravimetric (TG), differential thermal analyses (DTG), and calculated weighted averaged TG curves indicated that the influence of the biomass on the pyrolysis rate of the coal is small and vice versa. The CO2-producing reactions of the coal were slightly enhanced during co-pyrolysis.IntroductionCoal utilization has led to rising concerns about adverse impacts on the environment (global warming) caused by toxic gases (H2S, SOx, NOx, and CO2) and remaining waste. Biomass is considered to be CO2-neutral with regard to the greenhouse gas balance, and is regarded as a renewable source that assists in reducing CO2 emissions when compared with coal (McGowan, 1991; McKendry, 2002). Biomass currently makes up approximately 14% of the world’s energy sources (McGowan, 1991; McKendry, 2002). Coal combustion and gasification are prominent processes in South Africa (in producing synthesis gas and energy) due to the abundance of coal in the country. Some of South Africa’s coal resources are, however, high in ash content and also are inertinite-rich, which renders them more difficult to use industrially than vitrinite-rich low-ash coal (Jeffrey, 2005; Strydom et al., 2011). There is a need to investigate the properties and behaviour of the inertinite-rich high-ash South African coals and especially their interaction with local biomass sources. The gasification process occurs through various stages, of which pyrolysis of the char residue forms an integral part (Bunt and Waanders, 2009). Currently, particular interest is shown in the co-utilization of coal and biomass to produce synthesis gas via the gasification process (Usón et al., 2010; McGowan, 1991; McKendry, 2002). Investigating the co-pyrolysis of the South African coal and local biomass material is thus the first step in evaluating the use of local biomass sources for co-gasification purposes."

Jan 1, 2015

By Joseph E. Pogue

The writer visited the Muzo emerald mines in July, 1915, and spent six days in their study. This paper embodies the results of his observations, plus information personally communicated by Robert Scheibe, Professor of Geology in the Mining Academy of Berlin, who at the time of the visit was completing a detailed field investigation of nearly a year's duration of the emerald deposits of Colombia. An elaborate account of this valuable work may be expected at a future date from the pen of Professor Scheibe.

Jan 1, 1917

By Pratt V

The economic, social and political environment of the mining and minerals industries is, as we all know, volatile and affected by constantly changing international forces. In addition, the outcome of negotiations with overseas customers is often uncertain for long periods, or even unfavourable. The industries and companies represented at this Conference are in an arena of high competition, risk taking and enormous capital outlay. They are industries which our overseas markets (rightly or wrongly) have criticised for industrial relations problems, unreliable production and uncertain deliveries. They are industries which have an urgent need to be cost effective and competitive at all levels of activity.A critical factor in the mining and metallurgy industries is, therefore, its human resources and its human resource management. It requires the full use of available talent, innovation, skills and qualifications within its workforce, and the appropriate management of these resources.

Jan 1, 1985

By Juan B. Yianatos

"After almost 100 years, since the first commercial application began in Australia, flotation has shown an extraordinary growth and nearly 2 billion tons of ore per year are presently treated by flotation processes. During this time flotation has promoted a wide scope of research activities ranging from fundamental chemistry and hydrodynamic studies to studies of industrial operations. In general, fundamental studies have been mainly related to ideal situations. In recent years, however, large efforts have been focusing on achieving a better insight into the actual sub-processes provided by the development of new and more sophisticated instrumentation. Since the massive incorporation of flotation columns, around 15 years ago, a renewed interest in flotation fundamental studies, process modelling and new cell designs have been observed worldwide. The key role of the froth has been recognized as an independent and sometimes rate limiting process step. Thus, separation of pulp and froth process stages seems the most appropriate in terms of process modelling, diagnostic, design and scale-up purposes.In relation to flotation equipment development, until the middle of the 1970’s, only the sub-aeration mechanical cells were dominant. Since the 1980’s, the use of pneumatic cells and forced air mechanical cells has emerged strongly. Also, in the last decade, flotation equipment has shown a dramatic increase in size, reaching values of 200m3 in unitary mechanical cells and more than 300m3 in columns. The general feeling, however, is that, despite the great advance observed in terms of process knowledge, the mechanisms and principles of industrial flotation cells design and scale-up are still not fully understood.Advances in process instrumentation and control now in use allow for more efficient operations, both in metallurgical performance and savings in operating costs."

Jan 1, 2003

By Michael Ferrell

The primary reason pigments are used in plastics is to impart a desired color to the plastic. Color is one of the more important assign considerations associated with today's market oriented society. Secondary reasons for adding pigments to plastics include: 1. Improved UV stability 2. Enhancement to selected physical properties 3. Changes in optical properties Pigments may be used at loadings as high as 20% or as low as .001%. Generally the loading levels are between 0.2% and 2.0%. Pigments may be added to the plastic either by the manufacturer of the plastic, or by the user of the plastic. If the customer buys material that is already colored, it is referred to as "pre-colored". If the customer buys uncolored plastic and adds colorants, the process is referred to as "in-house" coloring.

Jan 1, 1985

By Thomas G. Chapman

The four major steps in the production of marketable copper are mining, concentrating, smelting, and refining. In a few cases, however, leaching takes the place of concentrating, smelting, and refining, and in others ores are smelted without being concentrated. Copper ores have been milled since the early days of mining in the United States. Except in the Michigan district, most copper ores went direct to the smelter until the so-called porphyry mines were developed. At present, although considerable leaching and direct-smelting ores are produced, the bulk of the copper ore mined is concentrated. Improved methods of concentration have kept pace with the increased tonnages of ores milled.

Jan 1, 1936

By Franklin D. Cooper

This Bureau of Mines study reviews current and proposed methods of extracting copper from sub-mill-grade ore by leaching. The amount of copper produced by hydrometallurgy has increased dramatically in recent years and will probably be about 200,000 tons per year by 1970.

Jan 1, 1968

By Joel S. Leventhal

The roles of organic matter in ore deposits are complex and represent a specialized effort in the larger subject of the geochemistry of ore deposits. The organic carbon cycle can be considered with particular emphasis to ore deposits in order to understand the origin and genesis of the organic matter. Organic matter may play one, several, or none of the following important roles in the formation of ore deposits: leaching, transport, concentration, reduction, and precipitation of metals. For deposits that contain organic matter, detailed field relationships and laboratory characterization of the organic matter are required to make an ore deposit model that Includes the organic matter and specifies its role(s). Examples of the involvement of organic matter in several types of uranium deposits are contrasted as being direct or indirect, syngenetic or epigenetic, and necessary or unnecessary. Examples of organic matter in deposits containing gold and lead-zinc, and In metal rich shale are discussed with respect to ongoing work and critical questions.

Jan 1, 2013

By Júlia Guimarães Sanches

O curso de Engenharia de Minas sofreu uma expansão, juntamente com todo o ensino superior no país, por volta de 2005. O objetivo do presente estudo é avaliar as características dos cursos do país e realizar uma comparação com cursos de outros países com grande produção mineral. Foi feito um levantamento inicial a partir de informações disponíveis nos sites do MEC, INEP e das universidades. Como complemento, realizou-se um questionário com os coordenadores dos cursos de Engenharia de Minas do Brasil. Foram compilados ainda dados relativos à estrutura curricular e carga horária dos cursos de Engenharia de Minas dos EUA, Canadá, Austrália, Chile e África do Sul. Em relação à comparação das grades curriculares com os cursos de outros países, observou-se que no Brasil o curso possui uma maior cara horária de Tratamento de Minérios em detrimento da lavra. Nos demais países estudados, o foco das disciplinas é a lavra, já que nestes países a área de Tratamento de Minérios é assunto de outras Engenharias.

Oct 30, 2017

By Carl N. Anderson

This paper, which is one of a group presented by the United States Bureau of Mines covering mining practice in different districts, deals in particular with the methods employed in mining the horizontal type of zinc-lead orebodies of the West Baxter area of the Tri-State zinc and lead district. These orebodies, locally termed "sheet-ground" bodies, with their relatively low working faces and low tenor of zinc and lead, require changes in the mining practice which is used in the balance of the district. In addition to the general mining methods, this paper also describes the system of hand sorting employed prior to the direct milling of the ore. The Hartley mine is situated mile west of Baxter Springs, Kans., as indicated in Figure 1. Its general outline and the location of the shafts with respect to the milling plant are shown in Figure 2.

Jan 1, 1932

By T. A. Laser

"INTRODUCTION A positive workplace environmental, health, and safety (EHS) culture affords organizations and corporations many benefits, including increased trust and employee morale, sustainable EHS performance improvements, and reliable productivity and profit margin growth. Unfortunately, many leaders and EHS professionals struggle daily to achieve and maintain positive workplace cultures and consistent business results. While lack of management support, corporate or employee buy-in, resources, and time are common factors that conflict with an EHS culture and safe work behaviors and processes, there are many other actions that threaten the positive attributes of an organization’s culture. Often these culture killers are not recognized, or worse yet, ignored because they are considered taboo. For example, voicing observations or questioning long-held management practices or process that were initially designed to promote EHS values, but no longer do so. Unfortunately, this could be viewed as challenging authority, not being a team player or even not valuing EHS. And for those that speak up, the potential for negative consequences can be real impediments to positive change. Having an open mind, constantly striving to identify culture killers, and putting forth the effort to eliminate them are the first steps to begin reaping the benefits of having a sound workplace culture. This paper helps readers to: • Recognize culture killers that negatively impact fostering and maintaining sustainable EHS cultures in the workplace. • Understand how to prevent, avoid, and respond to culture killers, before they wreak havoc in your organization. • Assess EHS culture strength, and implement plans to continuously improve it. The desire to draw boundaries around concepts, put things into boxes, and nail down requirements for something that is virtually impossible to solidify for any length of time is quite fascinating! These desires can pose challenges when trying to define what the perfect EHS culture should look like. The very act of trying to define our culture tends to create silos, and these silos, in turn, can become “culture killers”. The following is one of the most common culture killers. UNBALANCED ORGANIZATIONS TRIGGER CULTURE KILLERS Unbalanced organizations occur when an organization’s constantly shifting focus forces other important needs to take a back seat--until the focus changes again. This balancing act can be detrimental and lead to catastrophic results including low morale, lack of trust, employee dissatisfaction, high turnover, increased incidents, poor profit margins, loss of market share, and ultimately into organization-wide failure."

Jan 1, 2018