Search Documents

By John A. Clark, Danylo Oryshchyn, Casey Carney, Stephen Gerdemann, Cathy Summers, Thomas Ochs

"Limited analysis of combustion gas streams where carbon capture is not of interest is done mainly to ascertain operation parameters. Stringent regulations on acid gases and particulates promote careful flue gas analysis. Unregulated components are typically not analyzed. Typically not more than four points (two in the boiler, and one each in the flue and the stack) are sampled. A successful oxy-fuel process with carbon capture and compression is anticipated to require as many as 12 sample points with analysis for water, nitrogen, oxygen, argon, NOx, SOx, and carbon monoxide. Carbon dioxide captured for beverages produces a high value product and the cost associated with analysis is warranted. However, carbon capture for disposal must keep all costs to a minimum. This paper will compare alternative approaches for cost-effective sampling and analysis of the carbon dioxide product streams from oxy-fuel combustion, through all stages of production through compression and pipeline/vessel delivery.IntroductionAnalysis of gases in an oxy-combustion process with carbon capture is essential to the operations of the oxy-fired boiler and the subsequent collection, compression, and purification of carbon dioxide. The process is charged with pure oxygen and not-so-pure carbon in the form of coal at the front end, generating a product of mainly carbon dioxide with traces of argon, nitrogen, sulfur compounds, nitrogen compounds, oxygen, hydrogen, and mercury. It is possible that hydrogen chloride and hydrogen sulfide may also be present in trace amounts [1]. The trace components primarily come from impurities contained in coal such as water, sulfur, nitrogen, and volatile organic compounds. Coal also contains a good deal of mineral matter that is transformed into ash during combustion, becoming particulates that can complicate the analysis regimes utilizing standard analytical equipment."

Jan 1, 2010

By Irving Hartmann

The Bureau of Minas has been charged by the Congress with the responsibility for administrating the provisions of the Federal Coal-Mine Safety Act. One of the important duties of bureau inspectors under this act is to determine whether proper measures are taken to prevent mine explosions, which in moat miner includes Judea adequate rock dusting The investigation made after the explosion in Orient No. 2 mine, December 21, 1951, showed that much information is lacking on the adequacy of current rock-dusting and duet-sampling practices in the United States. To obtain such information, an intensive sampling survey was conducted by the Bureau in an Indiana coal mine. This paper summarizes the more Important findings from this survey, describes special samplings at several Pennsylvania coal miners, and discusses related studies in the Bureau's Experimental coal mine.

Jan 1, 1954

By H. A. Doerner

Tellurium is a silver white solid with metallic luster, the e17atal.line torm being ver., brittle aud e.g,s!ly powdered. It has a specific gravity of 6,27, melta at 45a0c. and boils at red het, giving off a. golden 1ellow vapor when air 11 excludei. When heated in air, telluri'UiD burns with a bl\te name tinged with green, and evolves wh1 te vapors ot tellurium dioxide. An amorphous form of tel­lurium, obtained by red.uction and precipi ta.tion from so).ution, haa II specific gr1.vity ot 6,015, and when heated ia cho.nged to the cry:.,talline variety. Telluri,a 11 insoluble in water, c&rbon diaiJ.phido, or h;rd.rochl oric acids, but it 11 41a-1olved bJ nitric or concen t1·ated. sulphi.U·ic acid. It 1..oea not tamiah in moiet ah•• 11 ree11tant to alkaline solutions, e,;:ctpt concentrated KOB, but it 11 cliaaolvecl by tuaed. &lkl 1••. I ts 11.to!!lic weight h..'l.a been the "J.Ubject ot mch controverq, bu\ t.he value 137 .5 :.a bl!ten generally accepted, Tho chflmietr:, of tellurium ia eim1lar to that ot IUlphur. It tonne throo xid.ee TeO, To02, and Te0 , al10 tellur14ea, t•llurite,, and. tellur1.t11, A number of halide compoWld.1, a 3iulph1de, and. a .ulpbat.e are known.

Aug 1, 1922

By W. P. Sykes

SEVEN years ago, Dr. S. L. Hoyt1 presented a masterful discussion of the hard metal carbides and cemented tungsten carbide. His lecture summarized most of the data then available in the field; many of the details relating to the production, properties and structure of cemented tungsten carbide had never been previously published, for, in fact, this information was only then being acquired. During the intervening years, the cemented carbides have assumed a place of real importance in the commercial field, with an ever widening variety of applications due to constant improvement in the control of production technique and the unremitting search for new compositions that might better the performance of the alloys in one or another type of service. The most recent summary of production methods, properties and guides for the successful application of the cemented carbides appears in the 1936 edition of the Metals Handbook. Of necessity, much detailed information relating to structures and physical properties is not included in such a summary, and it is with such details that the present discussion is concerned. STEPS IN PREPARATION While the past 25 years have contributed a valuable store of working knowledge in the field of powder metallurgy, many of the process controls are derived entirely from experience and are not as yet finally explained by a specific physical or chemical phenomenon. For most of the cemented carbides such difficulties are aggravated by our lack of knowledge not only of the complex alloy systems involved, but also by the possible changes in structure and even in composition which may accompany variations in temperature, heating time, and furnace atmospheres. The principal steps in the preparation of these cemented carbide alloys are fairly well known, but to supply a foundation for discussion these steps are briefly outlined as follows: 1. Formation of the metal carbide in the form of powder by heating a mixture of carbon and the metal powder or oxide for several

Jan 1, 1938

By Merete Tangstad, Eli Ringdalen

"In Norway ferrosilicon/silicon and ferromanganese production are strong with world markets of 4 % / 9 % and 4 %, respectively. Research and development in the academia mirrors the national interest; hence, there has been extensive academic research in these areas. There are some vital drivers and premises for a successful cooperation between the academia and industry with the main driver being a win-win situation for both. For industry,the potential advantages include cost-, competence- or environmental- benefits; for academia, the important drivers are building of competence and equipment, educating more students at higher levels, and increased possibilities to publish. In Norway, the benefits of cooperation between industry and academia are basic knowledge regarding thermodynamic and kinetic data, as well as reaction mechanisms within core processes. In recent years, such research interests have focused on the depletion of raw materials as well as environmental issues.IntroductionIn 1989, the Norwegian Ferroalloy Producers Research Association (FFF) was funded on the belief that a common research association would benefit the industry by making it easier to perform basic research as well as paving the ground for better recruitment to the industry. The funding partners in Norway were the FeSi/Si and FeMn producers. Today, the producers are Elkem, Finnfjord, Fesil, Wacker, Eramet and Vale. The main research partners working with FFF are SINTEF (Materials and Chemistry) and the Department of Material Science and Engineering at the Norwegian University of Science and Technology (NTNU). With more than 1700 employees, SINTEF is the largest independent research organization in Norway and NTNU is the largest technical university. Together, the two organizations provide an exceptionally strong materials technology research environment, and especially so for pyrometallurgical research."

Jan 1, 2012

By G. Dale Cor, Will H. Coghill, M. F. Williams, I. L. Feld

"INTRODUCTION During the past several years the Southern Experiment Station of the Bureau of Mines, with the cooperation of the University of Alabama, has given attention to hydraulic classification. One of the things this work has revealed is a variability not generally recognized in the conditions of teeter at different depths. This report depicts the passage of material through a teeter column and its emergence as a classified product.The work was made possible through the development of a classifier for several hundred pounds per hour permitting a small quantity of coarse spigot material to be discharged without the usual interruptions caused by stop-pages. Previous designs of small classifiers have been unsatisfactory because the,orifice used to control the quantity of spigot product as subjectto stoppages, particularly when attempting to discharge a small quantity of although the classifier used in this work has been described in detail in a previous publication 6/ its principal features will be discussed briefly herein. The main subject matter of the paper is based upon the three figures that illustrate in panorama the conditions that exist in a classifier during the continuous classification of bituminous coal, anthracite coal, and an iron ore trailing."

Jan 1, 1946

By R. R. Sayers

SILICOSIS is a term known to almost everyone today. Yet, in spite of a great deal of study, much is still to be learned regarding the disease. Government organizations are still continuing their investigations, begun near Joplin, Mo., 25 years ago. Work is also being done in several universities, as Harvard, Pennsylvania, Rochester, and Toronto, and at least two private organizations, the Air Hygiene Foundation of America, Inc., and the Saranac Laboratories for the Study of Tuberculosis, devote most of their time to this subject. Similar studies have been and are being made in many other countries.

Jan 1, 1939

By Corby G. Anderson

Antimony has been utilized by mankind for thousands of years. However, due to recent environmental concerns, antimony is often considered to be an impurity element, Since antimnoy is commonly found in precious metal refractory ore bodies, extraction is essential. The Sunshine Mine in Kellogg, Idaho has recovered antimony from its precious metal tetrahedrite deposits since the 1940's. A plant was initially constructed as a primary antimony source during World War II. This facility also decreased the downstream smelting penalty for the silver copper-lead concentrate and provided an industrial commodity from a potential environmental nuisance.' This paper describes the Sunshine antimony processing- facility. Specifically, the relevant process chemistries involved in concentrate leaching, metal electrowinning, and sodium antimonate production will be discussed. In addition, ongoing areas of research to improve unit operations and treatments implemented to meet environmental' discharge requirements will be covered.

Jan 1, 1992

By S Lakemond, L I. Ku, J Vaughan

Conventional processing of poly-metallic gold containing flotation concentrates are challenging for a number of reasons. One reason is that substantial copper and zinc in the cyanide leach solution compete with gold and silver for carbon adsorption sites. In this study, metal-cyanide adsorption kinetics and equilibrium are measured on three samples of coconut derived activated carbon and one sample of synthetic carbon. Loading selectivity was confirmed to be in the order gold>silver>copper>zinc for all carbon samples. The synthetic carbon tested showed promising results in terms of loading kinetics and capacity for precious metals.CITATION:Lakemond, S, Ku, L I and Vaughan, J, 2013. Effect of carbon type on adsorption of Cu, Zn, Ag and Au from mixed cyanide solution, in Proceedings World Gold 2013 , pp 411-418 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

"The rocks of Notre Dame Bay form part of the Central Paleozoic Mobile Belt (Williams, 1964) of the Newfoundland Appalachians. The Central Paleozoic Mobile Belt of the northern part of the island consists predominantly of Lower and Middle Ordovician rocks overlain by Silurian elastic and volcanic sequences and underlain in the marginal zones of the belt by polydeformed metamorphic rocks of the Gander Lake Group (Kennedy and McGonigal, 1972) in the northeast and the Fleur de Lys Supergroup (Neale and Nash, 1963; Kennedy, Phillips and Neale, 1972) in the northwest. The Ordovician rocks of the Central Mobile Belt have been subdivided into a number of local groups in different parts of the region. The Lush's Bight Group was first defined by MacLean (1947) . Recently Marten (1971) has revised the definition of this group, as shown in Table 1 and his revised definition is accepted in the present paper. Plate tectonic models that have been proposed for the development of the Newfoundland Appalachian System have indicated that the mafic volcanic rocks of western Notre Dame Bay represent oceanic crust (Bird and Dewey, 1970; Dewey and Bird, 1971; Church and Stevens, 1970) which marks the remnants of the proto-Atlantic Ocean first proposed by Wilson (1966) . Such models infer that the mafic volcanic rocks constitute the upper part of an ophiolite sequence. Analyses of the lavas show that they are tholeiitic and support this conclusion (Papezik and Fleming, 1967; Smitheringale, 1972) . A complete ophiolite sequence, consisting of peridotites overlain by gabbros, overlain by a sheeted diabase dyke complex which passes upward into pillow lavas, occurs at the base of the Snooks Arm Group (Upadhyay et al., 1971 ) . Sheeted diabase dykes are known to underlie the lowest mafic pillow lavas of the Lush's Bight Group at several localities in Notre Dame Bay (Strong, 1972, and pers. comm.) . However, several conflicting points about the geology of this region suggest that although a typical oceanic crustal sequence of Lower Ordovician age is present, older rocks occur within the ophiolite terrane in several places (Williams, Kennedy and Neale, 1972) ."

Jan 1, 1972

By M Qiao, A Sugden, W Zong, J Hines, J Roberts, T Ren

Long-term exposure to respirable dust continues to present an occupational health and safety hazard to mine workers in underground mines. Workers who are exposed to mine dust can develop occupational lung diseases including coal workers’ pneumoconiosis (CWP) or ‘black lung’, progressive massive fibrosis (PMF) and chronic obstructive pulmonary disease (COPD). To demonstrate the exposure impact of certain working conditions and improve dust management in longwall development panels, this paper details the development of a computational fluid dynamicsvirtual reality (CFD-VR) based training tool. The tool has been developed as an educational platform to facilitate the effective communication of workplace health and safety (WH&S) dust control measures for continuous miner operators and engineers. The study introduces a promising approach to model ventilation and dust flow patterns based on site-specific data, employing computational fluid dynamics (CFD) for a detailed analysis and visualisation of these mechanisms. Additionally, an algorithm has been developed for processing the large and complex CFD data sets into a form amenable for visualisation within a virtual reality (VR) environment using standalone VR headsets with limited processing power. This training tool has been deployed to mine sites with the specific purpose of educating users on the hazards of dust emissions and the best practices for control.

Apr 16, 2024

By Dale A. Zuck

Recovery of aluminum metal from drosses? is a major factor in the recyclability success story enjoyed by the United States aluminum industry. Today's modern dross processor uses the latest technology to maximize metal recovery at the lowest cost while complying with all environmental laws and regulations. Most dross processors, however, pay little attention to the resulting saltcake, the end residual of dross recyCling, and rely on landfills for .disposition of this material.. The alternative is to recycle the saltcake, but the success of this technology is dependent on the development of reliable outlets for each of the saltcake constituents. This paper discusses the evolution of an aluminum dross oxide processing technology that ,produces an economically attractive source of alumina for the production of portland cement.

Jan 1, 1995

By L Nagy, K P. Juhasz

The authors were engaged to optimise a traditional rebar cage reinforced concrete segmental lining by means of finite element analysis (FEA) using macro synthetic fibres for the Shanghai metro extension. The aim of this study was to reduce or entirely replace the original steel reinforcement of the segmental lining, in order to make the precast production process faster and more economic. The outer diameter of the tunnel was 6200 mm, the thickness of the segments was 350 mm.The numerical calculations were performed by Atena Finite Element software, which is based on the combination of Menétrey-William and Rankine failure surfaces on the compression and tension sides respectively. The effect of the macro synthetic fibres was modelled as tension stiffening on the tension surface.A one-to-one full scale model of an assembled tunnel ring using the original reinforcement cages was tested at Tongji University in Shanghai, July 2013. The ring was tested to differing load levels where load and displacement were measured until failure. The author’s first step was to calculate the real displacement characteristics of the original reinforced concrete (RC) ring, then calculate the numerically modelled version, so as to compare them. The material parameters of the concrete and rebar used had been determined through basic material tests conducted at the Tongji University. (Bi, Liu and Wang, in press).The numerical modelling undertaken has shown good correlation with the full-scale physical test results. Optimisation of the lining reinforcement was achieved through the addition of fibres, resulting in a substantial reduction of the steel rebar cages. Several results have been computed with the numerical model using different dosages of macro synthetic fibres, showing that the mass of steel reinforcement could be reduced by 50 and 75 per cent respectively.CITATION:Juhasz, K P, Nagy, L and Winterberg, R, 2014. Full-round numerical modelling of a macro synthetic fibre reinforced tunnel boring machine tunnel in the Shanghai Metro extension, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 477–484 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By Luis Angel De Montreuil

Ante el problema del tratamiento de minerales complejos, la demanda de eficiencia metalúrgica y bajos costos de operación, el ingeniero busca el apoyo de la mineragrafía como estudio microscópico de los minerales económicos. En ese sentido, el presente texto señala la importancia de la minegrafía -en tanto ayuda a la flotación de los sulfuros valiosos de los yacimientos peruanos. Asimismo determina las propiedades de los minerales con el fin de identificarlos.

Jan 1, 1986

By Sami Kara, Yunseok Park, Seung-Joong Lee, Namsun Hwang, Michael Laing

This study conducts a comparative analysis of construction efficiency. In the first part we compared electronic and non-electric initiation systems, focusing on tunnel contour holes. Field blasting operations were executed across a variety of delays to identify the optimal delay time. This delay for the in-situ rock mass was determined through regression analysis of blasting vibration in contour holes and for overbreak/underbreak. The blasting results with the electronic initiation system using the obtained optimal delay, applied to contour holes, were compared with the results of the non-electric initiation system. The overbreak and underbreak decreased by an average of 2.7 cm and 5.8 cm respectively, by using the electronic initiation system. Moreover, the vibration reduction rate in contour holes region was reduced by 11.9% based on the blasting vibration estimation equation proposed by the Ministry of Land, Infrastructure, and Transport (MOLIT). Underground construction projects have become increasing popular as cities grow in both size and density. This growth severely limits the amount of useable space for new project on the surface, resulting in the decision to build them underground. This new policy however brings into focus the challenge of managing and reducing blasting related vibration due to the proximity of these projects to sensitive structures, utilities and foundations often present in urban environments. For this purpose, we have been required to manage the vibration by reducing the quantity of explosives used per round. Inspired by surface blasting techniques, we applied a decking mode to address and work around this challenge. We present in this paper the first attempt to blast a tunnel face using a decking method and reduce the charging per hole from 6 kg to 3 kg per hole and keep the same advance rate for this tunnel. The results are presented in the third part of this paper. In the second part we present the results of the decking mode in shaft. The use of the electronic initiation system in tunnel construction provides the users an effective tool to improve the overbreak/underbreak and keep the vibration at a low level with a large gain on the overall project schedule and budget. This what we want to demonstrate in this paper.

Jan 21, 2025

By Gaston Gendreau

CETTE PRÉSENTATION traitera des différentes phases des opérations de la mine du Mont-Wright depuis ses débuts jusqu'à présent. A une brève description de la géologie du gisement, suivra un exposé des méthodes d'exploitation de la mine et du genre d'équipement utilize.

Jan 1, 1977

By Peter Zamora

Dado que ya no es posible confiar en el incremento industrial de las materias primas de las especies minerales y no metálicos de la tierra -en tanto estas son caracterizadas por condiciones minero-geológicas favorables-, el presente texto refiere posibles soluciones a través de yacimientos de grandes profundidades, condiciones desfavorables y de ley más baja que el mineral y así proceder a la explotación de los llamados yacimientos pequeños que hasta ahora han sido registrados y balanceados en el marco de la llamada "riqueza metálica" de tal o cual Estado, pero que no fueron considerados como industrialmente explotables a título de la explotación económica y técnicamente poco efectiva. Asimismo, la explotación de yacimientos minerales pequeños por los métodos clásicos de explotación masiva con utilización de la mecanización minera automóvil libre de carriles y la aplicación de los métodos geotecnológicos, elimina los procedimientos clásicos de afloramiento, trae el elemento de movilidad a los equipos de extracción y de beneficio. De esta forma reduce asimismo los costos de inversión de la explotación y permite así su explotación efectiva.

Sep 1, 1981

By P. S. Haury, Thomas C. Denton

"INTRODUCTION AND RESUMEThe Reward zinc property was one of the first selected for exploration by the Bureau of Mines at time when zinc supplies for war production were very short. Preliminary examination indicated that an appreciable tonnage of zinc that could be developed for early production might be found by diamond drilling. The geology was mapped by the Federal Geological Survey, and 14 holes were diamond drilled by the Bureau of Mines. This work was started in September 1942 and completed in September 1943.The Reward is an old property in southwestern Pinal County, 26 miles from Casa Grande on the Southern Pacific Railroad. Mining was begun in the early 1880's and was continued intermittently by several operators to about 1917. About 400,0oo pounds of copper was produced from the north¬eastern part of the property, mainly from a 600-foot incline in oxidized copper ore that replaced a bed of limestone. This ore was mined out. A 400-foot vertical shaft in the copper area was inaccessible. A 325-foot vertical shaft had been sunk near the southwest end of the zinc-bearing area, and a 600-foot crosscut tunnel had been driven near the northeast end of the zinc area, but little zinc ore was produced. There were several shallow inclines and numerous surface pits between the main workings.The ores were deposited in Paleozaic limestones that strike northeast and dip about 40 degrees northwest. These are capped by Cretaceous clastic and volcanic rocks in the zinc area. The outcrops show mineralization in a segment of the limestone 4,500 feet long, which is limited by large cross faults at each end. Another large fault, which strikes north, separates the northeast third of the mineralized belt from the remainder. Copper predominates northeast of this fault and zinc southwest of it. The ore beds are cut by numerous small cross faults. Ore was deposited for short distances along some of these, but more of it made out from the fissures along certain replaceable limestone beds."

Nov 1, 1946

By D. Ling, Santos. R. M., T. Van Gerven, M. Guo

The valorization of alkaline waste materials from thermal processes utilizing intensified mineral carbonation routes is investigated. The principal advantages of this approach are the chemical stability and storage safety of mineral carbonates, the opportunities for process integration presented by the technology, and the potential for conversion of low-value materials into useful products. Treatment and disposal of steel slags are a costly burden on steel plants. Sustainable solutions for Argon Oxygen Decarbonisation (AOD) and Continuous Casting (CC) stainless steel slags and Basic Oxygen Furnace (BOF) steel slag are desired. An integrated on-site mineral carbonation approach is envisaged as a favourable solution.

Jan 1, 2011

By Delvaux Carlos de Miranda Sobrinho, Hegler Zurick Arantes Assunção, Marco Venicio Mendonça de Souza, Luciano Toledo Ribeiro

This paper aims to present the development of a 600mm U-Pile that was done in Gerdau’s Ouro Branco Heavy Section Mill in order to feed the local market with a product.The focus of this study is to show the developmental process the Mill went through until it was prepared for hot trials. All roll pass and guide designs were developed by our own team. Analytical tools like Finite Element Analysis and reduced scale lead trials will be shown and how these tools impacted on the development timeframe and accuracy of the final results on steel.

Oct 1, 2019