Search Documents

By S. H. Moll, R. E. Ogilvie

The investigation of solid-state diffusion phenomena may lead to much information concerning binary alloys. In particular, a study of the concentration gradients present in multiphase diffusion couples can lead to the determination of the solubility limits of the single-phase fields in the phase diagram. The specific concentration gradient which results from the heat treatment of a diffusion couple depends not only upon the time and temperature of diffusion, but also upon the number of phases existing in equilibrium at the diffusion temperature. Such concentration gradients possess sharp discontinuities whose terminal points correspond to the solubilities existing at the limits of the two-phase field in the phase diagram at the diffusion temperature. In general, there will be a discontinuity in the concentration curve for each two-phase field which exists in the phase diagram between the concentration limits of the couple. A number of investigators have analyzed the gradients present in multiphase diffusion couples. 1-8 The iron-titanium phase diagram exhibits a y loop in the temperature range from 900" to 1400°C, and the limit of the a + y field lies at some composition which is less than 1 wt pct Ti for any temperature. It was felt that a diffusion study could yield values not only for the diffusion coefficients involved, but also for the chemical solubilities in the phase diagram. The concentration gradients were analyzed by an X-ray absorption technique developed by Ogilvie.6 The absorption of a monochromatic X-ray beam is measured in steps parallel to the diffusion direction and the resulting intensity gradients are transformed into concentration gradients by applying the laws of X-ray absorption in a binary system. This technique has been applied by ogilvie6 to the systems Ni-Au, Cu-Au, Fe-Cr, and Ni-Cr; by Gelles7 to the systems Be-Fe, and Be-Ni and by Hilliarde to the system Al-Zn. Linear X-Ray Absorption Analysis—The use of X-ray absorption analysis as a tool for determining concentration gradients arises from the fact that the beam is absorbed according to the quantity and species of elements present in the sample and not according to their state of aggregation. This method is more advantageous than the chemical analysis of machined layers since it is less time consuming and less expensive and can analyze a very small area. IF a homogeneous binary alloy (A + B) is analyzed with two different monochromatic X-ray beams I0(2) and lo(2) the following relation between the transmitted intensities, the intrinsic absorption coefficients of A and B for the two different radiations and the weight fraction of each element may be derived.' In (I/Io) (a+b) xa(u/p)a(2) + xb(u/p)8(2) Eq. [1] is independent of specimen thickness and density, but requires that either element A or B possess an absorption edge between the wavelength limits of the two monochromatic beams. I, is evaluated for each radiation by measuring the transmitted intensity through a varying number of foils of a suitable absorber. A plot of the natural logarithm of the transmitted intensity as a function of the number of foils, when extrapolated to zero foils, yields the value of I,. If a plot of the ratio in Eq. [ I] is calculated as a function of xA, then a master curve results. From

Jan 1, 1960

By M. A. Cook

Crude titanium metal, produced by the reduction of titanium tetrachloride with magnesium, is contaminated with some excess magnesium end adhering magnesium chloride when it is removed from the reaction pot. The method of vacuum 'purification is described in which the crude mixture is heated in a vacuum at a temperature of about 1,700° F. and the magnesium metal and chloride are volatilized away from the titanium, leaving it practically magnesium-free in a sponge-metal form. The pilot-plant equipment is described in detail, together with the technique of operation and methods of sponge recovery. Operating data is given, which compares ten 24- to 30-hour heats with ton 48-hour heats, and finally, power and labor requirements are discussed. Vacuum purification of raw titanium produced by the Kroll process has boon employed for treating of several tons of raw titanium with results for superior to those achieved by the method of leaching and grinding. The operations described, while on but little more than pilot-plant scale, indicate commercial feasibility of the process, even though it is a batch-typo operation. All equipment is either of standard manufacture or can be readily fabricated from standard materials, and operation of the units can be satisfactorily maintained by semiskilled labor.

Jan 1, 1952

By E. L. Reed

This paper addresses the state and federal permit- ting requirements and regulatory constraints associated with the development of new "grass roots" surface coal mines in the Western United States. Since a major portion of new coal development in the West will be on federally leased coal in Wyoming, my comments are directed towards that geographical area. This will give the reader some insight into the current regulatory framework within which western mining companies must operate-i.e., the major applicable state and federal laws and regulations, the more important state and federal regulatory agencies, and the major construction and operating permits that are required. Before discussing the impact of the regulations on our business, I would like to tell you something of my company and then briefly discuss Exxon's forecast of the long range outlook for coal. Carter Mining is an Won affiliated surface coal mining company. Exxon became interested in the coal business in the mid 1960's with the recognition of the future need for alternative fuel sources. Since that time, it has acquired coal reserves located in Wyoming, Montana, North Dakota, Arkansas, Texas, Illinois and West Virginia. Carter's first surface mine, the Rawhide Mine, located north of Gillette, Wyoming began production in August, 1977. Our second surface mine, Caballo, located just south of Gillette, began operating last October. We have a third block of federally leased coal just east of Gillette. By 1985 we anticipate Carter's western surface mines will be producing at an annual rate of 30 million tons, subject, of course, to successful market development efforts and regulatory considerations. Rawhide will ultimately have a permitted capacity of 24 MM tons per year. The coal at Rawhide is in two seams; one 80 feet in thickness and the other 20 feet (including a 6 to 10 foot parting). A large shovel is used to remove the overburden, and a similar shovel and dragline are used to mine the coal. Caballo has a 75 foot seam; otherwise it is similar in design and operation to the Rawhide Mine.

Jan 1, 1979

By F. Ntuli, T. V. Nyangadzayi

Chromium green is an essential metal with various applications in the paints, construction, electronics, and aerospace industries. The main source of chromium green is the carbo-thermic reduction of chromite ores, however, chromite ores are being heavily depleted on a global scale, hence the need to find alternative or secondary sources for the chromium. In order to meet the global demand for chromium there is a need to implement principles of the sustainable circular economy to keep chromium within the material loop. Ferrochrome slag and stainless steel slags are secondary resources that are potential sources of chromium. In this work, recovery of chromium from ferrochrome slag was investigated. The ferrochrome slag was alkaline leached using sodium hydroxide- sodium hypochlorite solution to reduce the use of potent reagents that have a potential negative environmental impact. The leachate produced by oxidative alkaline leaching of ferrochrome slag contained hexavalent chromium, which was used to recover the extracted chromium through a two-stage process involving reduction and precipitation. Reduction of hexavalent Cr to trivalent Cr was investigated using anhydrous FeSO4 at concentrations of 5 g/L, 10 g/L, and 15 g/L. Precipitation was conducted by dosing the reduced leach solution with 1 M sodium hydroxide at dosages of 5 ml/L, 10 ml/L, and 15 ml/L. The experiments were designed using the Taguchi (L9) orthogonal array and analysed according to the ANOVA, general linear model. The optimized conditions for the reduction step were ferrous sulfate dosage of 5 g/L with a pH of 12, and for the precipitation step, 1 M sodium hydroxide at a dosage of 15 ml/L with a setting time of 90 minutes and pH of 7. Physical changes were observed during the two-step chromium recovery, with solution changing from a yellowish colour to dark green colour indicating completion of the reaction. The chromium recovery was found to be 93.3%.

Dec 11, 2024

Discussion of the paper of GEORGE S. RICE and H. H. CLARK, presented at the Pittsburgh meeting, October, 1914, and printed in Bulletin No. 94, October, 1914, pp. 2563 to 2571. NORMAN V. BRETH,* Pittsburgh, Pa.-It was my privilege to visit in the last two months on behalf of the U. S. Bureau of Mines 10 mines where electric shot-firing systems controlled from outside the mine are installed. I will describe briefly what I saw in some of these mines, which are located in Utah, New. Mexico, Oklahoma, Alabama, and Kansas. At a mine in Utah, 230-volt alternating current is used to fire the shots, which is taken from a small transformer in the substation. The shot-iring circuit is independent of all other wires and is tested for grounds every day. There are no lightning arresters on the firing circuit. Porcelain insulators are used inside of the mine, and glass outside. The switches are situated as follows: One in the substation, one in, the shot-firer's cabin, two at each cross entry; where the shot-firing circuit crosses the trolley wire a switch is placed on either side of the entry in series with the shot-firing circuit. The miners are checked in and out of the mine. The coal is undercut and is shot down with permissible explosive, the shots being connected in multiple. There are 75 to 110 shots fired each day. A great many times there are no missed shots. If not more than two or three are missed they are left until next day. The fan is kept running at full speed when the shots are fired. The shot-firing switch is closed only once and the whole mine is shot at once. At another mine in Utah, power wires are used for shot-firing circuits; 500-volt, direct current is used to fire the shots. The only sizes of wire used outside of the power wires are Nos. 8 and 14 B. & S. gauge. The return is connected to the pipe lines and track. Porcelain insulators are. used inside of the mine.

Jan 4, 1915

By Eugene N. Cameron

Pegmatites of these areas have become important sources of beryl and lepidolite and have yielded cassiterite, columbite-tantalite, and other minerals. Examination of about 60 of these pegmatites leads the author to question the opinion of earlier investigators that the concentrations of beryl, lepidolite, and columbite-tantalite found have mostly formed by hydrothermal or pneumatolytic replacement of previously formed quartz-feldspar pegmatites. The author concludes, on the contrary, that present knowledge of the occurrence of minerals in zoned pegmatites can be applied to prospecting and mining of pegmatite deposits in these two areas of South West Africa. PEGMATITES occur in abundance in certain areas of South West Africa and in adjacent parts of northern Cape Province in the Union of South Africa. Some of the pegmatite deposits were prospected before World War I, and intermittent mining was done during the period between the two World Wars. The deposits of the Jooste lithium mines became an important source of lepidolite, and beryl, columbite-tantalite, wolframite, and other minerals were produced. Since World War II prospecting and mining have been carried on vigorously, with the result that South West Africa produced nearly 3000 tons of beryl during 1949 through 1953, together with more than 40,000 tons of lithium minerals, chiefly lepidolite and petalite. Small amounts of tantalite, columbite, and other minerals have also been produced during the postwar period. Most of this mineral production has come from two pegmatite areas roughly outlined in Fig. 1. One is the Karibib-Omaruru area of north central South West Africa. The second is the northeastern part of the Orange River pegmatite area, which extends into adjacent parts of Namaqualand, in northern Cape Province of the Union of South Africa. The writer visited the two pegmatite areas in July 1951. The visit was brief. but it gave an opportunity to compare some of the' pegmatites of these areas with those studied and described in detail by many investigators in the U. S., Brazil, and Canada during and since World War 11.'-l' The writer has attempted to determine, in a preliminary way, whether the concepts of internal structure and distribution of minerals in pegmatite bodies developed out of these studies are applicable to prospecting and exploration of pegmatites in South West Africa. Previous Work In an important series of papers (1929 to 1942) T. W. Gevers, H. I?. Frommurze, S. H. Haughton, G. K. Joubert, and other geologists of the Geological Survey of South Africa described and discussed the pegmatites of the two areas.*-" These works are the principal sources of information on the pegmatite mineral deposits of South West Africa. The investigations showed that in the two areas pegmatites are profusely distributed in pre-Cambrian rocks. These rocks are meta-igneous and metasedimentary units that have been folded and subsequently invaded by younger pre-Cambrian granites and by other igneous rocks. The pegmatites are considered to be genetically related to the pre-Cambrian granites. Pegmatites occur in the granite bodies themselves but are most abundant in the surrounding metamor-phic rocks, a pattern repeated in many pegmatite districts of the world. The origin of the pegmatites and the factors controlling the occurrence of mineral deposits in them were discussed at length by Gevers and Frommurze (1929)" and later by Gevers 14, 15 pp. 41-51, Ref.

Jan 1, 1956

By Edward P. Barrett

SPONGE IRON has been defined as the metallic product formed by the reduction (removal of combined oxygen) of iron ore or other iron oxides at temperatures below the fusion point of iron. This product probably derived the name "sponge iron" from its porous nature. When the reduction proceeds at slightly higher temperatures and the particles of metal weld together or finally even melt to yield pellets or balls that lack the porosity and low-density characteristic of sponge iron, the product might more correctly be called "direct iron."

Jan 1, 1954

By K. Terhaar

The objective was to determine operating protocols for a lead and silver column flotation cleaner, being considered for installation at Sunshine Mining & Refining Co.'s Kellogg mill in Northern Idaho. In this column, tetrahedrite and galena were floated, and pyrite and other gangue minerals, including siderite and silica, were depressed. The procedure was to develop a dynamic simulation using a linear transfer function approach. The transfer function related cause and effect variables such as the influence of collector and depressant dosages on recovery and grades. Bench-scale flotation tests followed by pilot column testing provided the data used to develop a linear transfer function. The transfer function was derived using a spreadsheet. This model was applied to simulate how the flotation column could be made to respond to disturbances in feed grade. The results were that xanthate, zinc sulfate, and sodium cyanide were found to be suitable controls for grade and recovery. Simulations showed the best sequence of manipulations of these reagents, and these sequences were useful for future operator training. The conclusion was that linear transfer functions were able to simulate lead and silver recovery, develop scenarios for operator training, and provide a foundation for future on-line control.

Jan 1, 1999

By L. M. Guayacán-Carrillo, G. Armand, A. Noiret, D. Seyedi, S. Ghabezloo, J. Sulem

"The main purpose of this paper is to analyze the convergence measurements in a drift excavated in the Callovo-Oxfordian claystone. The drift axis is in the direction of the major principal horizontal stress whereas the stress state is quasi-isotropic in the drift’s section. The initial geometry of the drift being circular, the anisotropic character of the deformation is taken into account by assuming that the drift shape evolves in an elliptical shape. The convergence measurement data on six different points around the drift are analyzed to identify the main axes of the deformation ellipse, following the methodology proposed by Vu et al. (2013, Rock Mech Rock Eng, 46, 231-246). Then, using the semi-empirical law proposed by Sulem et al. (1987, Int J Rock Mech Min Sci, 24, 145–154), the convergence evolution is fitted independently for each axis of the ellipse. This method permits to distinguish two effects: the face advance effect and the time-dependent behavior of the ground. The results for the two directions of the ellipse axes show very close values for the parameters describing the time-dependent properties of the ground, the distance of influence of the face, and the extension of the decompressed zone around the gallery. Such model can provide valuable insights for predictions of the convergence evolution in the long-term. INTRODUCTIONDeep disposal of radioactive waste has been studied in France for more than two decades. The French National Radioactive Waste Management Agency (Andra) began in 2000 the construction of an Underground Research Laboratory (URL) with the main goal of demonstrating the feasibility of a geological repository in Callovo-Oxfordian claystone. Several research programs have taken place to improve the knowledge of the rock properties and its response to the excavation progress. The optimization of supports design for long-term behavior is an important point to develop. A network of experimental drifts has been constructed with variations on: excavation method, structure geometry, supports system and orientations with respect to in-situ principal stresses’ directions. In each drift different sections have been instrumented to monitor the convergence evolution and the rock deformation. Continuous monitoring of the excavated zone around the drifts revealed the development of a fractured zone (extensional and shear fractures) induced by the excavation. The extent of this fractured zone depends on both the drift orientation and the in-situ stress field (Armand et al., 2014). Indeed, the fractures distribution has an important influence on the convergence of the drifts."

Jan 1, 2015

By H. R. Spedden

As part of its broad program of educational assistance-including grants, fellowships, and scholarships -Kennecott Copper Corp. offers summer employment opportunities for college students at each of its operations. Originally, summer job programs were intended primarily to help students defray their educational expenses. But as the nation's economy expanded with increased production and a growing demand for well-trained engineers, summer employment became an important means to help qualify future professionals and fill industry's need for them. Both the employer and the student thus derive benefits from such training.

Jan 6, 1967

By ERIK CHARRIER, ADITYA JUGANDA, Jürgen Brune, Gregory Bogin, Patrick Maier

Confined explosions are a major risk in underground coal mine operations. Depending on confinement, ignition location and obstacles in the flame path, methane explosions can transition to detonations. This research focuses on explosion experiments in a reactor with diameter of 71 cm and length of 30.5 m, along with developing the corresponding computational fluid dynamics (CFD) model that captures the observed flame behavior. The results show that the 2D and 3D CFD models are able predict the experimental flame front propagation velocity, but the 3D model shows more explicit conformity than the 2D model.

May 1, 2024

By James F. O?Neil

Brown iron ore deposits in Quitman County, Ga., were investigated by the Federal Bureau of Mines in cooperation with the State of Georgia, Department of Commerce, and the University of Alabama. Ninety-one holes were drilled, having an aggregate footage of 2,188 feet; seventy-one holes penetrated 248 feet of iron mineralization. Average thickness of the ore zone was 3.5 feet under an average thickness of 14.7 feet of overburden. The drilling developed inferred reserves containing nearly 30 million long tons of crude ore with an average analysis of 28 percent iron plus minor quantities of manganese. Test work done by the Bureau on the crude ore samples indicated that they would upgrade by current lug washer practice, with the use of a 1i8-inch screen, and yield 4.4 million dry long tons of concentrate with an average analysis of 52.1 percent iron plus manganese. The weight recovery obtained was 14.7 percent. Research studies made by the Bureau showed that the weight recovery would be increased by changing the screen size without any appreciable sacrifice of grade. The average weight recovery was increased to 18 percent with a 10-mesh screen and 22.8 percent with a 20-mesh screen. Screen tests studies indicated that there was no appreciable interlocking of the iron and manganese minerals and the clay and silica waste particles of the materials retained on a 200-mesh screen. Clay was prominent in micron-size slimes. Silica was deleterious in the minus 20-mesh size.

Jan 1, 1965

By Christopher Mark

After the United States and Australia, South Africa has the largest. modern underground coal mining industry in the world. Historically, South Africa has been the cradle of many innovations in ground control, particularly in the area of pillar design. Today, South African mines are grappling with many of the same issues faced by their U.S. counterparts, including safety during pillar retreat operations, selecting the proper roof support, and maintaining long-term pillar stability. The author recently visited seven underground mines in the Mpumalanga, Free State, and KwaZulu-Natal provinces. Mining methods included longwall, room-and-pillar with continuous miners, and drill-and-blast. The mines represented a cross-section of geology and ground support practices. At each mine evaluations were made of the Coal Mine Roof Rating (CMRR), roof support practices, pillar design methods, and general ground control experience. The coal seams observed were generally thick (2-5 m), the depths of cover moderate (less than 200 m), and the roof rocks relatively strong (CMRR greater than 45). Unfortunately, the South African roof fall fatality rate is approximately three times greater than in U.S., perhaps in part because roof bolts seem to be more widely spaced in most South African mines. Roof bolting equipment was generally outdated, and the quality of bolt installation was a major concern. Pillar design, on the other hand, is quite advanced, and pillar failures are rare. Several novel partial pillaring techniques are employed, including "checkerboard" mining in which every other pillar is removed, 3-cut systems, and high-extraction mining where engineered final stumps are left by design. The paper also offers observations on ground control management techniques (including recently introduced Codes of Practice), the role of the mine inspectorate, and the status of the research community.

Jan 1, 1999

By Alessandra Savazzini dos Reis

A incorporação de resíduo na massa argilosa é uma alternativa para diminuir o consumo de matéria-prima dando simultaneamente um destino adequado ao resíduo e assim preservar o meio ambiente. Este trabalho visa estudar a viabilidade técnica de utilização da lama de alto forno em massa argilosa usada na indústria de cerâmica vermelha. Neste sentido foram obtidas amostras da lama de alto forno e de argila e submetidas a ensaios de caracterização química, mineralógica e microestrutural. Amostras com teores de lama de alto forno variando entre 5% e 90% foram produzidas e queimadas em forno industrial à temperatura entre 800ºC e 900ºC durante 24 horas. As características tecnológicas avaliadas foram: absorção de água, porosidade aparente, massa específica aparente, perda de massa e resistência mecânica. Os estudos mostram que a lama de alto forno contribui para economia energética permitindo eficácia de queima. Os corpos-de-prova com até 5% de lama de alto forno obtiveram os melhores resultados nas características analisadas.

Aug 8, 2018

By N. Baloyi, P. Popoola, M. Tlotleng, S. L. Pityana

"The advantages of using Nb and Ti-Nb coatings for improving the hardness and corrosion resistance of Ti6Al4V were investigated. It has been reported that Ti6Al4V used in orthopaedic implants tends to release toxic Al and V ions into the surrounding tissue. Thin layers of Nb and Ti-Nb were deposited on Ti6Al4V substrates using a laser metal deposition technique. The deposited material was analysed using optical microscopy, scanning electron microscopy coupled with energy dispersive spectroscopy, and X-ray diffraction. The corrosion behaviour of the deposited layers was investigated using a Metrohm Autolab PG Stat101 compact potentiostat at 25°C in simulated body fluid. A Vickers hardness system was used to study the mechanical properties. Both Nb and Ti-Nb coatings exhibited good metallurgical bonding with the substrate. The microstructure and the XRD analyses for the Nb system showed that the ??-Nb phase was most dominant, while the Ti-Nb system comprised a mixture of the ?? and ?? phases. The average hardness of the Ti6Al4V substrate was 350 HV0.3, with a slight increase for the Nb coating (363 HV0.3) and a much higher hardness from the Ti-Nb coating at 423 HV0.3. The corrosion results show that the deposited Nb was more corrosion-resistant in the solution than either the Ti6Al4V substrate or the Ti-Nb coating. IntroductionMetals such as CoCrMo, 316L stainless steel, and NiTi alloy are used for manufacturing biomedical implants because of their distinct properties, including low Young’s modulus and resistance to corrosion (Ryan, Pandit, and Apatsidis, 2006). These implants are required to remain in the body of the patient for many years. Due to a favourable combination of mechanical and corrosion properties, titanium (Ti) and its alloys have emerged as the material of choice for biomedical implants. Nevertheless, their use is not entirely without challenges. For example, in total hip replacement, surface degradation and release of metal debris from metal erosion caused by friction limit the service life of the implant (Oldani and Dominguez, 2012; Manivasagam, Dhinasekaran, and Rajamanickam, 2010). Ti6Al4V is generally regarded as the material of choice, but it has been found that over extended periods of time, the combination of surface corrosion and erosion releases toxic aluminium (Al) and vanadium (V) ions into the body (Khan, Williams, and Williams, 1996). This has led to the investigation of titanium alloys containing niobium (Nb), zirconium (Zr), tantalum (Ta), and molybdenum (Mo) as substitutes for the aluminium- and vanadium-containing Ti6Al4V (Okazaki et al., 1997)."

Apr 1, 2019

By P. G. Dunn, J. Fitzgerald

ABSTRACT The scheduling of underground mining activities is a complex task that must simultaneously satisfy a large number of constraints. A schedule optimization tool (SOT) for underground mine planning is described, and its use for investigating strategic decisions is illustrated through a case study. The maincomponents of the SOT include (a) a genetic algorithm that searches for optimal schedules, (b) guidance for the application of heuristic rules, and (c) sliding, which implements just-in-time development. Findings indicated that preliminary scheduling performed before invoking the SOT, intended to provide a good starting point for the search, did not ultimately lead to higher value schedules.

Jan 1, 2010

By L. A. Cranson

WHEN I came out of Stanford University in 1922, the out-look for men trained in geology, petroleum engineering, and mining was indeed dismal; in fact, so much so that most of us looked upon our future in those fields as pretty hopeless. Neither our professors nor those men in industry with whom we came in contact gave us any enthusiastic encouragement as to the future of ourselves or the fields we had chosen for our labors. I believe that the attitude of pessimism which saturates everyone about graduation time is lament able and short-sighted, and may often start a young man on his way with an attitude of defeatism. Instead, he should be starting out knowing that he can expect hard work and keen competition, but that the fields of his labours are expanding at an accelerated rate, and that strong, energetic efforts will as always accomplish highly satisfactory results.

Jan 1, 1941

By R. J. Sweigard, R. V. Ramani

G.F. Learning The paper by R.V. Ramani and R.J. Sweigard is a wonderful description of the labyrinthine web that has been spun about the mining industry by energetic bureaucrats and politicians over the past 50 years. The remedy for the problem, however, is not more of the same, but less. That may be difficult for the industry to achieve, for it is not a technical solution but a political one. And the current fervor for more detailed planning at all levels of government and private enterprise has become deeply ingrained. The authors recommend the provision of more information about mining and mineral resources to "macro" (i.e., government) land use planners. They apparently overlook, however, the already strong tendency on the part of most government land use planners to consider themselves omniscient. Thus, giving them more information about the technical problems of mining will only make them want to get more and more involved in the "micro" (private, site specific) mine development and production plans of the individual mining firm. In fact, this has already happened at all levels of jurisdiction from municipal to federal government. Examples are legion. The most effective way to ameliorate the adverse impacts of government land use planning on existing and potential mining operations is to: (1) introduce greater flexibility in the definition of land use zones by local and state governments; (2) adopt realistic and relevant ambient environmental performance standards in governing relationships between mineral land uses and concurrent or subsequent nonmining land uses; (3) allow greater leeway for economic considerations in land use decisions in contrast to the explicit legalistic approach now in vogue; (4) recognize that all minerals are not the same and that sand and gravel mining should not be treated the same as underground metal mining, coal stripping, oil field production, or in situ leaching; and (5) eliminate the notion that mining operators should be responsible for determining in detail the use of land by subsequent owners of mined land. This last bit of conventional ethic really makes no more sense than requiring the builders of every shopping center or government office complex to provide detailed plans for the use of that land when its use for shopping or government is ended. Did the builder of Ebbetts Field plan for Brooklyn after the Dodgers went to Los Angeles? Should the developer of the Bingham Pit plan for suburban Salt Lake City after the copper mining goes to Chile? The nation's mining industry must address these questions before further bankrupting itself to provide more data to planners and spending thousands of dollars per acre to create land that when reclaimed is worth only a few hundred dollars per acre. Reply by R.V. Ramani and R.J. Sweigard We thank Mr. Leaming for his valuable contribution. His views on the problems of land use planning and mineral resources are most welcome additions to our paper. As the title indicates, our paper was more concerned with the impacts of land use planning on mineral resource conservation than with the details of the planning process. On the whole, his five recommendations would be helpful for mineral resource conservation. However, we would suggest that the argument he presents for his final recommendation does not address the differences between mining as a land use and commercial or institutional uses. We believe that this difference is the crux of the issue. We share Mr. Leaming's desire to ameliorate the adverse impacts of land use planning. Possibly the most detrimental impact is the loss of mineral resources. Any development, whether mineral or community, that does not give proper consideration to other resources can result in permanent loss or sterilization of resources. With proper planning, some of these losses can be avoided. As our paper indicated, one factor that limits the consideration of mineral resources, and ultimately leads to their sterilization, is the generally inadequate levels of resource characterization and understanding of the unique nature of mineral resources and mining operations. The last point raised by Mr. Leaming is also important. In terms of reclamation and land use planning in mining districts, we certainly do not advocate spending more than what the results are worth. The main thrust of the paper was to explore the avenues for conserving the mineral resources so that, at some appropriate time, the issue of mining and reclamation can still be addressed.

Jan 4, 1985

By B. Rai

Aluminum is produced by the Hall-Héroult process, which involves passing a current through a molten mixture of alumina dissolved in cryolite (Na3AlF6) to reduce the alumina to aluminum. This process occurs in an electrolytic cell comprising a steel shell lined with a carbon cathode and refractory bricks. After a certain period of operation, the carbon cathode deteriorates and is removed from the cell along with the refractory bricks. These removed materials are referred to as spent pot lining or ?SPL?. Typically, 30 Kg of SPL waste is generated for every ton of Aluminum produced. Globally aluminum smelters produce more than 500,000 tons of SPL each year. Even though SPL has a high fuel value (8000 to 9000 BTU/lb) and contains valuable metals, it is classified as a hazardous material due to its cyanide content and leachable fluorides. Various disposal/recycle techniques have been developed over the years for SPL but none of them is satisfactory. Thus, large quantities of SPL are still being dumped in landfills. In some countries, even the land filling of SPL is not permitted. The safe disposal of SPL thus remains a challenging problem to the aluminum industry and the search continues to find methods of converting SPL into a non-hazardous waste and/or recovering the valuable materials contained in the SPL. We have developed a process to produce hydraulic setting cements (eco-cement) containing a novel fluoride rich cementitious phase, from SPL by an energy efficient, low temperature clinkering route. A raw mix blend of SPL, lime/limestone, calcium sulfate and tailings sands based on a set of design criteria developed by us, is clinkered in a two stage process; 2 hours soak at 800 °C followed by clinkering at 1000 °C for another 2 hours, to produce a soft clinker. The SPL eco-cement is made by grinding the clinker to a fineness of 5000 cm2/g Blaine with 1% by weight borax as a set retarder. A good quality cement having as high as 20 % by weight of SPL in the raw mix (28 % by weight in the cement clinker) is thus produced. The physical properties of the SPL cements are found to be comparable to the Indian standard (IS) specifications for Ordinary Portland Cements (OPC). We have produced the cement in a few Kg batches and tested the reproducibility of results from batch to batch for further scale up. Once commercialized, this process has a potential of converting SPL into value-added cement products. Keywords: cement, spent pot lining, clinkering, fluoride, aluminum, ordinary portland cements

Sep 1, 2012

By C T. Portelli

Belt conveyor transfers are the most likely location for high wear rates and failures. Belt transfers are necessary to change the direction of conveyed material and will remain a part of belt conveyor systems into the future. Burden being accelerated due to fall and changes in direction from one system to the next, prevents steady state flow which introduces component fatigue. The conveyor belt is considered the greatest cost item over the life of a belt conveyor system and consumes considerable downtime to replace, therefore a financial incentive exists to preserve this high-cost item. Other issues created at the transfer include health risks of uncontained dust and product losses due to spillage. Additional consideration to support the belt is one way to improve the life of components and contain dust within the transfer chute. The humble impact cradle/bed has changed little over the years whilst conveyor systems have achieved ever greater flow rates. Further development of the impact cradle is an opportunity to reduce maintenance costs and increase uptime. The peak technology on the market for conventional impact belt support is the dynamic impact cradle, which ensures the belt support area under the chute allows for some dynamic travel, whilst also maintaining a consistent skirt board area. The impact energy at a transfer when installed with Kinder Australia’s dynamic impact belt support system was measured to further understand the forces involved and how they compare with static belt support systems. Adding further dynamic capacity to the load zone has been shown to increase belt life by at least 30 per cent. Other components also benefit from reducing impact energy in the transfer and the incorporation of polyurethane bushes at roller supports has been employed further increase roller and frame life. Kinder Australia has developed a unique and innovative range of belt support technologies that further promote dynamic travel whilst maintaining a consistent skirt board area without a significant increase in belt-friction tension. This technology combines slider rails with rollers that can absorb impact independently within the support system and/or utilising exotic slider materials to overcome high belt speeds and/or system capacities. Kinder Australia has a vast library of documented case studies and application data to ensure the future systems being offered will survive, provide better chute sealing and protect the conveyor belt.

Sep 18, 2023