Search Documents

By A. Haines, O. Varaud, I. Baidoo

Abosso Goldfields Limited (AGL) is in the process of developing an expansion of their Damang Open Pit gold mine in Ghana. AGL acquired the Damang mine in January 2002, with SRK participating in the geotechnical investigation and design for the project since 2001. A deep resource drilling program, completed during 2004, intersected an extension of the orebody below the then planned final pit floor. A feasibility study has been completed to determine the economic extraction of this deep ore with an expanded pit shell. The Damang mine is in a stockwork sulphide deposit at the culmination of the Damang anticline. The deposit occurs as hydrothermal mineralisation associated with dominantly east dipping thrusts and sub-horizontal quartz veins. Primary gold mineralisation also occurs in the conglomerates of the Tarkwaian Formation. The geological units consist of steep easterly dipping dolerite, sandstone, siltstone and phyllite beds, with the weathering profile comprising saprolites overlying a relatively thin joint oxidized horizon. It is planned to deepen the current open pit to a final depth of up to 270 m, primarily by the development of a push-back of the eastern and western walls. The edge of the Eastern Tailings Storage Facility (ETSF) is currently located within 80 to 100 m of the crest of the existing pit. The geotechnical design focused on the optimization of the bench face angle and finally recommended a ?Steep Slope Strategy?, involving 24m high near vertical benches. Limiting bench stack heights of 96m at a maximum of 66° were derived from the influence of major structures and the variation in rock mass conditions. The overall slope angles in each pit sector were developed around the requirement for haulage ramps. One of the main design challenges was to optimise the standoff distance between the final pit crest and the ETSF. This process had to consider maximum access to the resource without undue influence on or from the nearby tailings dam. A planned increase to the height of the dam wall was an additional factor in the design. Dewatering of the pit walls was also a major consideration in this tropical environment.

Jan 1, 2006

By Francis Foley

INTRODUCTION DURING the summer of 1919, the late Dr. Henry M. Howe, then Chairman of the Division of Engineering of the National Research Council, organized a committee to obtain a better insight into the behavior of carbon steels under the influence of various treatments by a proper control of the time and temperature factors. During part of 1919 and 1920, work in connection with this investigation was carried on at Dr: Howe's laboratory at Bedford Hills, N. Y. During 1921 there was an enforced hiatus in the work, occasioned by the illness which resulted in Dr. Howe's death in 1922. At that time one of the present authors compiled the results of the work which had been done and this was published in 1923.1 Following the publication of this work, it seemed desirable to carry on in the same manner an investigation of steel of C 0.75 per cent., which steel had not been as fully treated as had the other steels of C 0.34 and 0.52 per cent., used in the published work. Furthermore, certain unusual results have been obtained in the treatment of C 0.52 per cent. steel by quenching and drawing, and repetition of this part of the work seemed advisable. This has been done during the past year at the School of Mines and Metallurgy of the University of Missouri at Rolla, Mo., by a cooperative undertaking of the School and the Bureau of Mines, working in conjunction with the Committee on Heat Treatment of Carbon Steels of the National Research Council. The present paper is a report of the results obtained in this work.

Jan 2, 1926

By David F. Gearhart

The Burrell Can1 is a thin, steel, tubular shell filled with aerated concrete that is used as a roof support in coal mines. The Can height is always shorter than the mining entry, so it is capped with wooden timbers and wedges when it is installed. This combination of the Can and the wooden header is a standing support system that is designed to yield in a controlled manner and exhibit a constant yield, or elastic-plastic behavior. The Burrell Can is capable of withstanding 20 in or more of vertical convergence and 15 in or more of horizontal displacement. Because of this exceptional ability to sustain load through extended convergence and displacement, it is one of the most robust standing supports in use today. The National Institute for Occupational Safety and Health (NIOSH) conducted testing on seventeen Burrell Cans in 1995, during development of the support where the ratio of the height to the diameter, or the aspect ratio, was between 2:1 and 4:1. Based on the results of that testing, it was suggested that the standard aspect ratio of the Can be less than 5:1. This suggestion is intended to preserve the overall stability of the Can, which will help to maintain the initial stiffness and prevent load shedding. Recently, the necessity of the aspect ratio has been questioned, and this issue will be addressed in this paper. Since the initial development and introduction, more than 130 tests of the Can have been conducted at the NIOSH Mine Roof Simulator (MRS), and 25 of those specimens had aspect ratios greater than 5:1. The 18-in-diameter by 10-ft-tall specimens had the largest aspect ratio, 6.67:1.However, the aspect ratio is not the only parameter that affects the performance characteristics of the Can. Multiple factors, such as the use of different wood species, the use of different header or footer configurations, and the use of pedestals, as well as biaxial loading conditions can also decrease the stiffness and capacity of the Can. Data from full-scale tests that include these other factors are analyzed to show that the initial stiffness is primarily affected by the roof and floor contact configurations. Furthermore, load shedding is more likely to occur or begin earlier when the aspect ratio is greater than 5:1 and one or more of the other factors are present.

Jan 1, 2012

By Madgwick J. C

A novel, microaerobic, heterotrophic microbial leaching system for manganese dioxide is described. Mixed natural microflora were enriched by addition of sugars and crude plant nutrItIOnal supplements. Between 84 and 104 mg MnH was solubilized per gram sugar at I per cent (w/v) concentrations for fructose and galactose in the presence of 0.03 per cent w/v dried microalgae (a Chlamydomonas species). Some 42 per cent soluble manganese was dissolved by microbial action on MnO, (3 per cent (w/v) pulp density) using a 10 per cent (w/v) molasses growth substrate.

Jan 1, 1983

By L. M. Lenahan, J. D. Sheets

INTRODUCTION The Raleigh-Durham International Airport (RDU) in North Carolina is the fourth largest airport in the southeast region of the United States. The Raleigh-Durham Airport Authority is currently underway with planning, designing and constructing are placement Passenger Terminal as part of the Major Capital Improvements Program at Raleigh Durham International Airport. The Terminal C Expansion and Renovation Project will replace the existing Terminal C structure with a new processor building and concourse. The project is separated into several contracts. The early stage contracts are constructing a west side storm water management facility, relocating taxiways, installing new drainage systems, installing new aircraft apron pavement, Demolition, the Central Energy Plant and Early Foundations. The later projects are the Terminal Building, Passenger Boarding Bridges, Information Technology Systems and Integration, Furniture, Furnishings & Equipment and Specialty Millwork. The Terminal Building will be constructed in two phases. Phase 1 constructs the north half of the new terminal. Airline operations will move to the new terminal at the completion of this phase. Phase 2 completes construction of the south processor building. The full build out of the project, subject to funding availability, will replace the remainder of the south concourse. The Program’s primary focus is to replace the existing passenger Terminal C with a new terminal that will provide more passenger gates and larger passenger screening, ticketing and baggage handling facilities. The planning for the New Terminal C Program began in 2002 with construction starting in March, 2003. The continuing growth of passenger airline travel in the Raleigh/Durham metropolitan area requires RDU to expand its facilities to keep up with the present and future growth within the Region. In October of 2002, the RDU Airport Authority selected Parsons Transportation Group as the Program Manager/Construction Manager to help assist in the development of the Terminal C expansion program. RDU Airport Authority selected the Seattle Washington Office of URS Corporation as the Engineer of Record for the West Side Storm Water Management Facilities. The Westside Storm Water Management Facilities Project became one of the early critical path activities of the overall RDUAA Terminal C Expansion Program. The Briar Creek Reservoir had been constructed to accommodate storm water runoff to the west of the Airport. The existing 1.5 m culvert that drained runoff from the airport terminal (area) to the reservoir was insufficient in supporting the additional flows

Jan 1, 2005

The ability to track miners and communicate with them while they work in underground coal mines is important during normal daily operation, and critical in emergency conditions. This was evident during recent incidents at underground coal mines worldwide. Communication with miners and the knowledge of their location is of great importance for rescue efforts and the preservation of life. Numerous technologies have been developed, adapted and deployed to meet tracking requirements of the Mine Improvement and New Emergency Response (MINER) Act of 2006. Evaluating the performance of these systems has proven to be dif?cult for mine operators, system manufacturers and regulatory agencies. The MINER Act requires operators to improve accident preparedness by developing an emergency response plan speci?c to each mine. With the recent implementation of the provisions of the MINER Act of 2006, all underground coal mines in the United States are subject to the mandates of legislation concerning communication and tracking system installation. As of June 2011, 203 new or revised tracking and/or communication systems had been approved by the U.S. Mine Safety and Health Administration (MSHA), with nearly 50 other systems or revisions in the approval process (MSHA, 2011). At that time, the available approved systems for underground coal mine use included these types: ? Leaky feeder communication systems. ? Fixed node-based communications and/or tracking systems. ? Wireless node-based communications and/or tracking systems. ? Medium frequency (MF) communication systems. ? Communication system peripherals. Other types of tracking systems have since been developed and some manufacturers are seeking approval for use in this application. Some of the new products include through-the-earth (TTE) systems and various radio frequency (RF) adaptations. New technologies that are currently being developed and deployed in other industrial applications should also be considered, including acoustical, optical, inertial and hybrid technologies. To date, no uniform method has been employed in the industry to effectively compare and evaluate the performance of installed systems. Neither industry operators nor regulatory agencies can accurately assess the capabilities of installed systems in the continuously changing mine environment. There is a need for a uniform evaluation method that provides the ability to assess how different systems and technologies perform in various mining applications, and whether they can satisfy the regulatory requirements.

By J. -M. Rescoussier

Due to Important settlements inducing major structural damages, the western part of the Grand Littoral shopping centre has been closed in 1997. The present paper describes the project of underpinning including not only micropiles under the structure of the building but also a reinforcement of the soil located between the shopping centre and the edge of the embankment surrounding the western part of the shopping centre. The aim of this reinforcement is to reduce existing horizontal movements to allowable values.

Jan 1, 2002

By Enrique Albarrán, Julian Hernández

"In 1942 The “Presa Mixcoac” dam was built, along with 15 other dams, to control the rain fall waterin the mountains west of Mexico City. Mexico City’s population at that time was around 1.5 millionpeople, and the dam was way out of the city."

Jan 1, 2016

By H. Gumede

The occurrence of fracturing due to high stress levels is a major factor in hangingwall stability in deep level gold mine stopes. However, rock falls cannot be the result of these fractures alone. Rock falls can result only from the occurrence of unstable rock blocks defined by the interaction of the stress induced fractures and naturally occurring geological planes of weakness. These planes include bedding planes and joint set planes. However, there is a general lack of information on the characteristics of these planes (orientations, spacings and lengths)?it does not appear that any such systematic and quantified information, if collected, has been published. To remedy this situation to some extent, joint mapping exercises have been carried out in several geological environments in two gold mines. The data collected on joint geometry included orientation, spacing and length, and this information is included in the paper. In addition, the paper describes the use of the data collected to evaluate the potential for rock falls and the probability of failure of stope support

Jan 1, 2007

? Hollow Stem Auger ? Drill Bits ? Leads/Torque Arm ? Hydraulic Gearbox ? Hydraulic Power Unit ? Grout Pump ? Crawler Crane

Jan 1, 2003

By E. Pardo-Igúzquiza, R. A. Olea

The bootstrap is a computer-intensive resampling method for estimating the uncertainty of complex statistical models. We expand on an application of the bootstrap for inferring semivariogram parameters and their uncertainty. The model fitted to the median of the bootstrap distribution of the experimental semivariogram is proposed as an estimator of the semivariogram. The proposed application is not restricted to normal data and the estimator is resistant to outliers. Improvements are more significant for data-sets with less than 100 observations, which are those for which semivariogram model inference is the most difficult. The application is illustrated by using it to characterize a synthetic random field for which the true semivariogram type and parameters are known.

Jan 1, 2015

By Francis D. Leathers

Four friction pile load test programs, including 23 tension tests and 9 compression tests, have been performed as part of the Central Artery/Tunnel Project in Boston, Massachusetts. The tests, performed on both precast, prestressed concrete (PPC) piles and steel piles, yielded the following adhesion values: [Soil Type Clay Clay Glacial Till Interbedded Sand and Clay Interbedded Sand and Clay Pile Type PPC Steel Steel Steel PPC Adhesion (psf) 610 to 1,200 230 to 900 220 to 550 680 1,280 ] The adhesion appears to be affected by differences in pile material type, with PPC piles having higher adhesion than steel piles. However, part of the apparent difference for the clay may be due to differences in time between driving and testing. The significant range of test data means that the need for site specific testing to determine or verify design values of adhesion should be considered during design. Creep rates at loads near failure ranged from about 0.02 to 0.18 inches per log cycle of time, with most values in the range of about 0.04 to 0.08 inches per log cycle of time.

Jan 1, 1994

"This paper reviews the chemistry involved in the recovery of gold from cyanide solution with anion-exchange resins, and also discusses the most critical aspects of the engineering of an effective resin-in-pulp (RIP) process. As far as the chemistry is concerned, the conclusions reached by a great many researchers, as well as the performance of the only operating RIP plant in the Western World, at the Golden Jubilee Mine in South Africa, support the view that the process is technically viable and, in many cases, could prove to be more attractive economically than alternative processes such as zinc cementation and carbon-in-pulp (CIP). On the engineering side, there is still a need for further development before larger scale ( > 50,000 tpm) RIP plants can be designed, built and operated with confidence. However, the experiences gained during nearly 3 years of operation of the Golden Jublee RIP plant indicate that the process can be engineered with confidence for smaller operations ( < 50,000 tpm), and this will probably be the scope of application of the first-generation RIP plants. INTRODUCTIONThe use of anion-exchange resins in gold processing has, for a number of years, been proposed as an alternative to more conventional processes such as zinc cementation and carbon adsorption, and detailed research programs that have been carried out at a number of laboratories have demonstrated the technical viability of the process. (Burstall et al, 1953, Davison et al., 1960, Tataru, 1973, Laskorin et al. 1978, Hosking, 1984, Riveros and Cooper, 1987 and Palmer et al., 1988)The main incentive for this work was the fact that resins have several characteristics that are quite different from carbon, which make them potentially more attractive substrates for the recovery of gold. The following are examples: -"

Jan 1, 1991

By S. N. Opperman

Testwork at Goedehoop Colliery showed that fine coal, essentially?150 microns can be successfully beneficiated using froth flotation. Both conventional and column flotation were tested. It was found that the traditional stirred tank type of flotation machines used in conventional flotation produced the best recovery of fine coal. After extensive testwork it was decided to develop a flotation machine on Goedehoop Colliery that would combine stirred tank and quiescent column technology. It was thought that this design would give the best combination of recovery and selectivity. The Multicell was developed and is producing results acceptable for Witbank coal flotation. Keywords: Multicell, Witbank coal flotation, froth, stirred tank, quiescent column.

Jan 1, 2002

By Roger S. Jackson

"This study interprets vibrations produced by single underground shots, recorded on surface by 135 digital seismographs laid out in four linear arrays. Several vibration anomalies were observed and are investigated. A novel method of displaying the blast-induced vibration iso-contour data relative to the three-dimensional representations of the geological rock units and structures leads to the following interpretations:• The identified faults commonly dampen or amplify vibrations, on the evidence of the peak particle velocity,• Strong anisotropy of geologic formations produces different vibration attenuation in the various directions of interest,• Low-vibration “depressions” can be related to the presence of faults, and• Higher vibration levels than expected based on ‘scaled-distance’ principles are observed close to intersecting faults.The interpretations from this study document a better understanding of the geotechnical influences on blast induced stress wave propagation in a geologically complex area. The practical benefit of this understanding is better control of surface vibrations, experienced from underground mining activities."

Jan 1, 2010

The history of soft and hard rock underground mining is blemished with regional instabilities of mine workings. Whilst the potential consequences of regional instability events are recognised to be high, there is a false perception that the probability of them occurring is very low. In fact, Australia has averaged more than one event per year for the past 20 years. At least five fatalities and over $100 million of losses have been associated with the events. As such, they are a core risk to underground mining and have a significant effect on the quadruple bottom line of business û safety, environment, community acceptance and economics. This paper explores the important roles that risk management has in reducing the probability and consequences of regional instabilities. It concludes that education and continuing professional development are essential elements for effectively managing the risk.

Jan 1, 2003

By J. E. Friant

Until 1956, drill and blast was the only way to excavate rock. In that year, a tunneling machine using disc type cutters economically bored a small Toronto tunnel. Its amazing 105 ft/day set a new world record and set the stage for a new industry. The Disc Cutter Role in Excavation Mechanical excavation of hard rock is by now deeply ensconced in the heavy civil construction industry. All over the world, from the Swiss Alp Melange to Hong Kong Granite, to New York Gneiss, huge Tunneling Boring Machines (TBMs) create transportation, water and sewer tunnels. Powerful machines, boasting as much as 6000 hp, bore through rock, excavating in excess of 1400 tons per hour. The tool that makes this tunneling phenomenon possible is the single blade, rolling disc cutter. These hardened steel discs, from 15 1/2 to 19 inches diameter are arranged on a rotating cutterhead, to cut concentric circles in the rock. As the machine is propelled forward under great pressure, rock below each cutter is crushed. But the efficiency of the cutterhead is derived from the science of cutter spacing (distance between cutter paths). The majority of the rock excavated is not crushed, but flakes off in chips and chunks. No pick, tooth, or drag type cutting tool can duplicate the performance of a disc cutter. The economic use of drag type tools is limited to as low as 5,000 psi UCS rock strength in massive formations. In weakly bonded, foliated rock, drag tools do better, but are still limited to rock generally less than 15,000 psi.

Jan 1, 2002

By E. T. C. Spooner, Ioannou S. E.

"Abstract- The Dixie Zone Au-Ag deposit is a low sulfidation (adularia-sericite) epithermal system located 1.4 km from the producing Ken Snyder mine (7.0 M oz Au equivalent reserve/resource), Midas Mining District, north-central Nevada. This WNW striking, steep south dipping, fault system is hosted by mid-Miocene (17 Ma to 14 Ma) felsic volcanic rocks that were erupted from a vent(s) to the northeast. The system was mineralized by approximately 250 ± 20°C (n = 86), near-neutral pH, ascending fluids of predominantly meteoric origin [volatile corrected salinity = 0.52 ± 0.35 eq.wt% NaCl (n = 86)]. Bulk analytical fluid inclusion gas chromatography identified a mineralizing fluid volatile composition of 99.68 ± 0.18 mole % H2O, 0.16 ± 0.09 mole % CO2, 0.11 ± 0.05 mole percent N2, 0.05 ± 0.04 mole % CH4, and 0.01 ± 0.01 mole % CnHn+i (n = 7). Sulfur species were not analyzed due to absorption within the chromatography system; however, a H2S concentration of 16 ppm to 160 ppm molar is estimated. The volatile content contributes approximately 50% of the microthermometrically measured freezing point depression. Cl- concentrations up to approximately 9000 ppm suggest an additional, probably magmatic, fluid component.Ascending fluids were channelled along approximately NW striking faults related to the same primary extension (17 Ma to 14 Ma) responsible for Nevada basin and range physiography. Boiling induced by CO2 effervescence led to precipitation of Au and Ag over a 150 m vertical interval. At the time, this interval was about 460 m below the water table (approximately 38 bars), but because of erosion, it is now within 90 m of the surface. A Ag:Au ratio of 25:1 has been calculated for the Dixie Zone."

Jan 1, 2000

By Jerry Ran

Stope back caving in a mine using open stope mining interrupts the planned mining sequence and causes oversize muck and dilution with adverse economic implications. As many underground mines are mining or have plans to mine at depth, stope back caving could have significant impact on the mine sustainability. Therefore understanding the caving mechanism is important in preventing future occurrence and improving the mine economic performance. Falconbridge Ltd Kidd Mine is an underground mine using open stope method producing more than 2 million tonnes per year. Its current lowest mining level is approximately 2070m below surface and the lower portion of the orebody is being developed. In years of 2002 and 2003 the back of three stopes of approximately 1900m and 2040m below surface caved and caused substantial mining difficulties at the mine. As these caved stopes are subject to stress concentration, seismic activities and near major geological structures, the caving mechanism is much more complex than that of stopes near surface. In addition to the recorded caving history by site observations, the mine carried out cavity surveys and test drilling to define the caved profiles. The mine seismic monitoring database provided information at these stopes. Stress modeling work conducted by an external consultant provided the stress patterns at the caved stopes. Based on the field collected data and stress and seismic information, this paper presents details of the stope caving process and cavity surveyed profiles, reviews the predictability of the stability graph approach for these cases, discusses the caving mechanism and proposes preventive measures to stabilize the stope back.

May 1, 2004

By B. J. Buys

Rock bolt integrity is a critical issue for the mining industry because of its influence on the safety of mining operations. Guided ultrasonic wave testing of the defects associated with resin-anchored rock bolts was investigated. Axisymmetrical and three-dimensional finite element models were built, one of a partially encapsulated bolt and the other of a bolt with a simulated local corrosion crack. Experimental bolts were then installed in a testing block and typical responses were compared to finite element models of different defect scenarios. Encouraging results were obtained for the smaller axisymmetrical and three-dimensional finite element models, as well as during the experimental investigation. It is recommended that software with energy-absorbing elements should be utilized to consider higher frequencies and longer bolts. Once the integrity of models such as these has been established, the models could in principle be used to train neural networks for use in commercial equipment to determine the integrity of the installed bolt.

Jan 1, 2009