Search Documents

By M. Menéndez

Enhanced gravity separation appears to be one of the most promising methods for processing all types of <200-µm coal feeds and tailings. Systems based on this technology are reviewed, and the results of investigations based on C900 Multi-Gravity Separator tests conducted to assess the treatment of <200-µm, extremely difficult-to-wash coal settling pond tailings are presented. Multi-Gravity Separator processing tests of ultra-fine tailings with a high clay particle size content (22.6% <10 µm and 60.1% <40 µm) and a 69.56% ash content show that this material can be effectively treated after desliming (<10 µm) of clay-size particles to produce a coal with a 20.6% ash at a separator combustible material recovery of 69.3%. Desliming is shown to be critical in reducing coal ash content and combustible material recovery. Similar improvements are anticipated in the recovery and separation pro-cesses for other enhanced gravity separation systems from the desliming of feeds. Although not a conventional form of treating Multi-Gravity Separator data, the existence of well-defined polynomial relationships based on the product of drum shake amplitude and shake frequency relative to product coal recovery, product ash content and yields at varying wash water flows is demonstrated. Low-amplitude and intermediate- to high-frequency bed agitation are shown to produce optimum ash reduction results.

Jan 1, 2007

By Peter Zhang

The immediate roof at the test site consisted of laminated clay shale that is likely to be susceptible to weathering. With seasonal dry-wet cycles in the mine ventilation air, the roof in the intake air would deteriorate and lose integrity over time. In many instances, the weathering-prone roof would gradually scale off piece by piece between bolts and over the entry corners. In some long-term entries, roof weathering could develop up to 2-3 ft deep with columns of bolted roof hanging under the upper intact roof. If wire mesh is used, the roof bags down and reduces the entry height, and the weight of the bagged roof tends to pull the bolts out and poses a safety hazard. An effective measure is always sought to support this type of weak roof that is sensitive to moisture degradation. One solution is to seal the roof shortly after entry development to prevent moisture penetration so that roof integrity can be maintained for the long term. In this application, a polymer-based sealing material was tested in the Rockspring mine for weathering protection and reinforcement. The material is a one-component polymer powder for spray application onto the roof and rib. The sealant material is mixed with water in the spraying nozzle to apply to the roof and rib as a paste. The product sets within 5-10 minutes and forms a membrane as thin as about 1/8-in. The membrane will quickly develop tensile and bonding strength within minutes and completely cure within a few days. Through sealing, bonding and lateral reinforcement, the integrity of the weak roof can be maintained. The material has been tried in a long-term evaluation over several months in a set of main entries in the Rockspring mine owned and operated by Rockspring Development, Inc., affiliate of Foundation Coal. Preliminary evaluation has shown that the material is an effective and economical solution to ensuring the long-term stability of weathering-prone roof.

Jan 1, 2009

By George Markon

The importance of United States coal exports as a component of the national economy, the potential for growth of these exports, and the inter-national character of this sector of the coal industry are described in this report. The report summarizes some of the many background elements in the rise of United States coals to preeminence in highly competitive world markets. It presents some insight into this important sector of United States industry and the positive contribution of this sector to the Nation&apos;s balance of payments. It contains pertinent basic statistics on production, trade, and consumption of coal in most major markets for 1960-66. The report examines the movement of United States coals from mines to export markets, tracing and describing origins, exit ports, prices, and trends as well as inland and ocean freight rates and other data vital to an under-standing of some of the practices and complexities of the United States coal markets abroad. A brief sketch of coal production and consumption in principal importing countries is also presented with a short review of some of the more current practices and problems of these countries. Coal produced in inland areas of the. United States can be moved to and distributed economically within coal-producing countries overseas and in Canada. Quality coals from the United States can successfully compete with foreign coals in nearly any area of the world on a truly economic basis because of their high grade and their low cost which derives from the high productivity of the miner and from reasonable ocean freight rates. Because of tariffs, trade embargoes, quotas, and other restrictions, how-I ever, foreign coal markets are relatively limited. Further limitations are imposed in some countries by economic conditions which restrict all imports as a matter of financial and economic necessity. Despite these obstacles, United States coals have brought lower cost quality coals to a large segment of the foreign energy market.

Jan 1, 1968

By H. Reginald Hardy

This report is Volume I of a three volume final report on the micro-seismic monitoring of a longwall coal mine. Volume I deals for the most part with the detailed aspects of the microseismic field study itself, however, brief references are made to other secondary studies described in Volumes II and III. During this field study a mobile microseismic monitoring facility and associated transducers were employed to detect and record microseismic activity above a longwall panel at Greenwich Colleries, Barnesboro, Pennsylvania. The fundamental objectives of this study were (1) to evaluate the feasibility of detecting microseismic activity originating from longwall mining operations using an approximately planar, near-surface, geophone array installed above the longwall and (2) to attempt to locate the sources of the various microseismic events. This investigation has proven that, using the techniques developed it is possible to detect microseismic events at depths of more than 400 ft and at horizontal distances in excess of 800 ft from the source. The majority of the observed events were found to have frequencies on the order of 10 to 100 Hz, and particle velocities of 50 to 300 µips. When a suitable velocity model was utilized, most of the events located were computed to be within ±100 ft vertically of the coal seam and ±50 ft horizontally of the longwall face. The results of the overall research project suggest that additional research should be undertaken in a number of associated areas.

Jan 1, 1978

By C. E. Van Orstrand

An intrusive body is a mass of igneous rock that has migrated upward, presumably from great depths. Great variations in form, composition and depth of burial occur. It is not proposed in this paper to go into all of the details of the problem. Instead, it mill be assumed here that the intrusive has the form and characteristics represented in Fig. I. According to W. 11. Emmons minerals are not deposited in appreciable quantities below the "dead line." Important amounts of ores of virtually all metals may be found around summit cupolas, but only gold, copper and zinc (in limited quantities) are usually associated with trough cupolas. Most students of ore deposits agree that temperature changes are largely instrumental in precipitating many ores in the "hood" and that the difference in temperature between the intrusive and that of the country rock may be the chief factor in determining the mineralogy of a deposit. A problem then of some interest is to correlate the principal physical features of the intrusive with the phenomena of heat conduction as evidenced by the cooling curves and the isothermal surfaces. Mathematical Theory In order to show the possible application of heat conduction to the interpretation of the processes of metalliferous deposition associated with intrusives, it will be as- sumed that the intrusive is a large par-allelopiped of dimensions, 2l, 2m, 2n. The equation that represents the flow of heat from the parallelopiped into country rock (v = o, 1 = o), which has the same thermal properties as the intrusive, is2,3 l-x v I FT 2 [2 2 — l-x m — y — m — y n — z In this equation, the origin, x = o, y = o, z = o, is at the center of the parallelopiped. v = temperature at point x, y, z, time 1. v, = initial temperature throughout the intrusive, 1 = o. k = coefficient of thermal diffusivity. a, ß, y are variables of integration. Put n = m in Eq. I, and we have v I [2/5 [2I-x 2 — l-x m — y 2 2 2 kt 2 20xt e-a2da ebrdß

Jan 1, 1946

By C. E. Van Orstrand

An intrusive body is a mass of igneous rock that has migrated upward, presumably from great depths. Great variations in form, composition and depth of burial occur. It is not proposed in this paper to go into all of the details of the problem. Instead, it mill be assumed here that the intrusive has the form and characteristics represented in Fig. I. According to W. 11. Emmons minerals are not deposited in appreciable quantities below the "dead line." Important amounts of ores of virtually all metals may be found around summit cupolas, but only gold, copper and zinc (in limited quantities) are usually associated with trough cupolas. Most students of ore deposits agree that temperature changes are largely instrumental in precipitating many ores in the "hood" and that the difference in temperature between the intrusive and that of the country rock may be the chief factor in determining the mineralogy of a deposit. A problem then of some interest is to correlate the principal physical features of the intrusive with the phenomena of heat conduction as evidenced by the cooling curves and the isothermal surfaces. Mathematical Theory In order to show the possible application of heat conduction to the interpretation of the processes of metalliferous deposition associated with intrusives, it will be as- sumed that the intrusive is a large par-allelopiped of dimensions, 2l, 2m, 2n. The equation that represents the flow of heat from the parallelopiped into country rock (v = o, 1 = o), which has the same thermal properties as the intrusive, is2,3 l-x v I FT 2 [2 2 — l-x m — y — m — y n — z In this equation, the origin, x = o, y = o, z = o, is at the center of the parallelopiped. v = temperature at point x, y, z, time 1. v, = initial temperature throughout the intrusive, 1 = o. k = coefficient of thermal diffusivity. a, ß, y are variables of integration. Put n = m in Eq. I, and we have v I [2/5 [2I-x 2 — l-x m — y 2 2 2 kt 2 20xt e-a2da ebrdß

Jan 1, 1946

The paper point out the way whereby the Canadian gobernment regulates and motivates mineral development. In this sense, its important the role of Gobernment policy in the development of the industry to its a stage. The progress of industry is due to a favorauble political climate which created an atmosphere of trust that has atracted foreing investment. Therefore, Canada's position owes much to sound legislation that recognizes the high element of risk in exploration and development and also the exhaustibility of mineral deposits.

Nov 20, 1969

By M. Mononen, J. Huuskonen, M. Vauhkonen, J. Kourunen, A. Lehikoinen

"A new approach to measure process conditions in flotation cells is presented. Real scale flotation cells in a Zinc circuit are imaged using Outotec LevelSense sensors based on electrical resistance tomography. The latest results from long period plant tests show that the sensors together with FrothControl analysis give new information that correlates well with other process parameters. The sensors can compensate for electrical contact contamination using an automatic calibration technique and they are basically maintenance free. The results indicate that using the LevelSense sensors and FrothControl solution, the process control and optimization can be done automatically, stabilizing and improving the metallurgical performance of the flotation process.INTRODUCTIONThe froth flotation process is widely used in mineral industry for the separation of minerals from low-grade ore slurry. Different property parameters of froth and slurry could be measured to monitor and control the flotation process: air bubble size distribution, flow dynamics, thickness of the froth bed, amount of solids in the froth, etc. Some techniques already exist that can be utilized in studying these important parameters on-line. Examples of the techniques are the high-speed video imaging, simple conductivity probes, ultrasound techniques, floats and pressure transducers (Maldonado et al., 2008). These techniques, however, often suffer from some limitations. For example, the video imaging only gives information from the surface of the froth, simple conductivity probes suffer from contamination and the floats may get stuck and therefore do not give reliable signal for process control and optimization."

Jan 1, 2013

By M. Rice, M. Stanley, J. Marlow

Arizona construction aggregate industry remains in the crosshairs of public debate, caught between the need for aggregate-based building materials and alternative, high-value land-uses. To better manage lands and improve land-use decisions, the Arizona State Land Department has need for a system to assess potential aggregate resources on State Trust lands, and assign dollar values accordingly. Thereafter aggregate values can be compared to residential, commercial, agricultural, recreational, and habitat values -- in a determination of highest and best land-use.

Jan 1, 2002

By Jairo Londono Arango

El presente texto realiza un diagnóstico sobre la producción y el mercado del carbón colombiano a través de los datos utilizados del último censo minero realizado en 1983, donde de describe los sistemas de explotación, nivel de tecnificación y los rendimientos alcanzados.

Jul 1, 1985

German manufacturer DBT signed a contract to supply a sixth automated-plow long-wall system to Shenyang Coal in Liaoning province in northeastern China. This most recent order occurred just weeks after DBT signed a contract to deliver a fifth automated-plow longwall system to Datong Coal in Shanxi province. The plow will go into service at Shenyang Coal’s Hongyang Mine. Mining conditions at the mine, coupled with DBT’s advanced automated-plow technology, means that the system has the potential to become one of the world’s most productive thin-seam longwalls.

Jan 1, 2004

By Robert L. Hautala

In 1978, Congress established a series of mineral institutes for a limited time to assist financially in mineral industry education and research. Later, education and research were separated, establishing generic institutes for specialized research that transferred the former research budget from the base mineral institutes program. One of the generic institutes is the Mine Systems Design and Ground Control (MSDGC). It provides for research funding specifically for mining. Other parallel generic institutes were established in pyrometallurgy, comminution, waste management, etc. MSDGC was established at Virginia Polytechnic Institute and State University(VPI). The founding group included the University of Alabama, University of Kentucky, University of Nevada Reno, University of Idaho and University of Alaska reporting through VPI to the US Bureau of Mines (USBM) and Congress. Other universities also participated on an ad hoc basis.

Jan 1, 1996

By L Mackinlay

The Apeketon Business Hub in Lihir, Papua New Guinea, emerged in 2019 through a partnership between Australian Business Volunteers (ABV) and Lihir Gold Limited (LGL), a subsidiary of Newmont Corporation. This development was driven by a shared vision for the Lihir gold mining operation to further enhance opportunities for the local community and strengthen the economy’s resilience post-mine. At its core, the business hub serves as the epicentre of ABV’s operations in the region. It includes a drop-in resource centre which provides the community with mentoring and consulting services, and access to a range of impactful workshops facilitated by ABV’s local staff and skilled volunteers. These workshops focus on local Lihirians but are open to the entire community, including Newmont employees. We design and continually refine Apeketon Business Hub support programs and offerings driven by community priorities, building trust through long-term relationships, and working side-by-side on real-time challenges. We offer three core programs to different levels of the community, from individuals and families to start-ups, large corporations, and landowner groups. There is significant demand for the support services provided by ABV, with over 350 Lihirians participating in our workshops over the 2023 calendar year. One of the hub’s core offerings is the Family Money Management Program, which addresses crucial challenges faced by Lihir households, particularly in terms of financial resilience. The program takes a comprehensive approach, assisting families in long-term planning and developing skills to effectively manage the income they derive from their employment with LGL and other enterprises. Significantly, the program also addresses financial stress, a factor often associated with domestic violence (Fox et al, 2002). By empowering women and promoting joint financial decision-making, the Family Money Management Program fosters a culture of savings and improved financial management, ultimately enhancing economic resilience within the community.

Sep 1, 2024

By J. H. Hedges

During the World War Leadville was an important producer of manganese and maganiferous ores for then steel industry. Normally, the market for these ores is limited to the requirements of the local steel mill at Pueblo for low-grade ores used in making, basic pig iron containing 1 to 2 percent Mr and spiegoloison containing 20 percent Mn, but during the war and a brief period of postwar readjustment, a good deal of 25- to 40-percent manganese ore qua shipped to in-stern steel-manufacturing centers. Throughout the active life of the camp, manganiferous iron ore carrying a little silver and lead and sometimes as such as 35 percent Mn was chipped to load smelters for flux. The total reordered production is 936,024 tons of metallurgical ore shinned to steel mills and 2,576,514 tons of fluxing ore, much of it of metallurgical grade.

Jan 1, 1940

By Wolfgang Roth

In 1990, a residential area above the North Outfall Sewer (NOS) tunnel constructed in 1924, experienced subsidence. After sewage was diverted into the North Outfall Replacement Sewer (NORS), soil probing from within the tunnel was conducted, soil-improvement options were developed, and a preferred grouting scheme was analyzed by numerical modeling to evaluate the stability of the 80-year+ old tunnel liner under grouting-induced loading conditions. This paper discusses the initial field investigation and the development and analysis of a grouting scheme originally intended to be implemented before relining of the tunnel. The scheme was later modified, and the new liner was installed before the final probing and grouting work was done.

Jan 1, 2008

By Zhuokun Cao

Manufacture of aluminum foams still suffer from nonuniformity and poor reproductively for there is lack of basic knowledge of foaming process. In this paper, carbon fibers are used as novel stabilizing additive for aluminum foams, and the structure evolution of aluminum foams with different fiber content was studied. A laser rangefinder was used to detect the expansion rate of different al foams. Al foam samples are solidified at different foaming time to determine its relative density and cell size distribution. Results indicate that the cell size of foams linearly increases with the decrease of density, and the slope of the line is influenced by fiber content. The relationship between expansion ratio, density and cell size of the foams is discussed. It is concluded that the density of resulting foam is influenced by the rate of gravity driven drainage, and its cell size is determined by expansion ratio and foaming time.

Jan 1, 2010

The Johnny Mercer lyrics &apos;You&apos;ve got to accentuate the positive, Eliminate the negative, Latch on to the affirmative à&apos; would best sum up the traditional approach to community relations in the mining industry. This &apos;90s &apos;Public Relations spin&apos; approach, usually backed up by scientific data, technical reports and graphs outlining risk probability and the impact potential on people and communities, is being challenged. Challenged by communities who have greater access to information, demand greater levels of transparency and corporate responsibility of large corporate operations and possess greater awareness of the communities they live in. &nbsp; The growth of the environmental movement, of anti-globalisation, anti corporatism, apprehension of a large corporate&apos;s ability to deal with community issues, and a lack of faith in the abilities of regulators to regulate corporate activities, means our industry faces challenges on multiple fronts. It must now be able to address these from a personal/community perspective if it is to remain relevant within communities. &nbsp; One of the keys to this is linking the internal activities and responsibilities to the externals concerns and demands for higher levels of operation and care. &nbsp; This presentation draws on Corporate Public Affairs trends, functions and approaches and the application to External Affairs activities within Newmont Waihi Gold&apos;s operations in Waihi and regional exploration activities throughout the Hauraki Goldfields. &nbsp; The approach presented works on the philosophy that communities don&apos;t necessarily have to like what we do, but should be able to identify and recognise the way in which we involve them in decision making, communicate our intentions and respond to issues.

Jun 1, 2010

By Benoit Bissonnette

"The need for production of a competent fill was recognized early by the project partners. Consequently, a 4000 Ud paste fill plant was constructed and commissioned in early August 1994.In order to fine tune the process without risk to the underground workings, a closed pumping loop was devised on surface. After two months of this exercise, the first underground slope was filled according to specifications obtained from the pilot plant trials.This paper will focus on the operational problems encountered and the solutions adopted so far, and on a comparison between expected and actual fill production and characteristics.RésuméLa nécessité de produire un remblai de propriétés mécaniques suffisantes a été rapidement reconnue par les partenaires du projet. Conséquemment, une usine de production de remblai en pate, utilisant les residus du concentrateur d'une capacité de 4000 t/j a été construite et l'opération a débuté au mois d'aôut 1994.Dans le but de roder le précedé sans mettre en danger les installations souterraines, l'usine a été testée dans un circuit de surface. Après deux mois d'essais, le premier chantier souterrain a été rempli avec du remblai en pate selon les specifications dérivées de l'usinage pilote.Cet article présente les problemes d'opération rencontrés et leurs solutions, en plus de faire une comparaison entre les résultats prévus et ceux actuellement obtenus sur la production et sur les charactéristiques du remblai."

Jan 1, 1996

By May J. R

Exploration, including research, has fuelled the enormous expansion of the Australian mineral industry in the last three decades. Analysis of success and failure in exploration and research has therefore potentially powerful lessons and messages which may be used to influence the future shape and direction of the mineral industry. Research has been an integral part of organised corporate mineral exploration since its beginnings in Australia in the 1930s. In corporations, the activity generally called project generation or new project development is the main expression of exploration research but mostly it goes unidentified and poorly documented except perhaps when a successful discovery is made and reported on. The competitive nature of exploration means that extended and detailed analysis of corporate exploration research across the industry is impossible to achieve.

Jan 1, 1992

By M A. Tuck

The dominant heat loads in a deep underground mine are the surrounding rock mass, autocompression and machinery. In addition heat can be contributed to by other sources. Many block cave, sublevel cave operations and coalmines utilise conveyors to transport broken rock out of mine, in some cases completely, in others in combination with other forms of transport. This broken rock can be loaded onto the conveyor at virgin rock temperature and can represent a major heat input to the ventilation airflow as it is transported out of the mine. The purpose of this paper is to review established knowledge regarding heat flow, from conveyed rock to determine the main factors influencing the heat flow and to develop a methodology for predicting heat flow from caved rock. The paper concludes with suggestions for further research in the area of conveyed rock heat transfer.CITATION:Tuck, T A, 2017. Accurately estimating heat load from conveyed rock, in Proceedings Australian Mine Vent Conference 2017, pp 225–230 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017