Search Documents

By Hugh M. Wolfin

This Information Circular is an abstract of a manuscript which was completed in June 1933, by Mr. Hugh M. Wolflin, formerly of the U. S. Bur eau of Mines. This abstract has been prepared by Charles Will Wright for presentation at the February meeting of the American Institute of Mining and Metallurgical Engineers in New York. It has been necessary to omit many of the details and most of the cost data and tables, as well as the illustrations in the original manuscript. As the use of airplanes in mining developments is making such progress and as a publication on this subject to be of greatest value should include the most recent information, it is unfortunate that, due to a lack of printing funds, it has not been possible to publish this manuscript. The purposes of Mr. Wolflin's paper are: (1) To describe briefly what has been accomplished in some outstanding examples by the use of aircraft in the mining and petroleum industries, (2) To record costs, (3) To present available information and suggestions to assist in solving future air-transportation problems in the industries under consideration.

Jan 1, 1934

By Arash Maghsoudloo, Asli Can

"Abstract This paper presents a ground improvement implementation case under a raft foundation of a local hospital. The selected ground improvement method is Wet Soil Mixing (WSM) technique. Soil mixing is increasingly applied to environmental applications and ground stabilization in geotechnical projects. In this technique, weak soil is mixed with cementitious slurry to improve the characteristics of the soil. The investigated case is one of the pioneering WSM ground improvement technique implementation cases in Turkey. The soil profile is mainly consisted of low plasticity clay. The effect of ground improvement is verified by a series of laboratory tests and four in-situ pile loading tests. The results of in-situ pile load tests on constructed soilcrete columns showed an acceptable factor of safety for the bearing capacity of the WSM columns. Measured bearing capacities in all four tested columns were nearly 20% higher than calculated values. In addition, a set of samples are obtained from the constructed columns and unconfined compression tests have been conducted. The laboratory test results indicate that the selected cementitious slurry has a sufficient efficiency to form the stabilizing columns.IntroductionIn the construction industry, stabilization of the soft ground by lime or cement stabilization is a widely used technique. In ground improvement systems deep mixing method (DMM) results in the same stabilization in deep portions of the soft soil profile by mixing cementitious slurry by means of mechanical augers. The pioneering cases of modern deep mixing application can be traced back to the year 1970 that was used for the stabilization of marine soils below the water level for the construction of harbor structures (Terashi et al., 1979). Nowadays, DMM is shown to be a proper and efficient method for the foundation of the structures and embankments on land. Some recent studies also reported that reasonable settlement reduction range in the stabilized soils under the foundation of structures (Archeewa et al., 2011). In addition to reduction of the structural settlement under service loads, deep mixing methods are also utilized when there is a concern with contaminated soil and groundwater or groundwater control (Andromalos and Bahner, 2003).Although, the DMM is shown to be a successful method in numerous studies for improvement of a wide range of soil types such as organics, fine-grained, and coarse grained material, it has some limitations (Archeewa et al. 2011, Jameson et al. 2010, Jelisic and Leppanen 2004, Lambrechts and Roy 1997, Meyersohn 2007, Miki and Nozu 2004, Olsson et al. 2008, O’Rourke and McGinn 2004, Stewart et al. 2004, Yang et al. 2011). High soil density and stiffness could damage deep mixing rigs. Engineering properties of the soilcrete columns changes based on the soil type, water content and other factors such as organic content of the available soil profile, so properties of the generated soilcrete should be verified by a set of rigorous testing procedures (Puppala et al. 2004).Based on the general classifications presented in the ground improvement literature, deep soil mixing method is divided into two main types of dry or wet mixing methods. In the dry and mixing methods compressed air and water are utilized as the binder transporter medium respectively (Moseley and Krisch, 2004). In addition, DMM methods can be categorized based on the employed mixing methods during the construction. In this study, the main aim is to present and elaborate on the selected method is known as Wet Speed Soil Mixing (WSSM)."

Jan 1, 2014

By Qingzhu Li

The brewing industry byproduct, spent grain (SG), was evaluated for its ability to adsorb Ag(I) from aqueous solutions. Ag(I) adsorption was dependent on solution pH, contact time, adsorbent dose, initial Ag(I) concentration and temperature. The kinetic data were well described by pseudo-second-order kinetic model, indicating that chemical adsorption was the rate-controlling step. The equilibrium data followed Freundlich isotherm rather than Langmuir isotherm, suggesting heterogenity of the adsorption sites on spent grain. Ag(I) desorbed from Ag(I)-loaded spent grain was also evaluated in this study. HCl, NaOH, Na2S2O3 and ultrapure water were chosen as eluants and desorbed Ag(I)-loaded spent grain for 30min, Ag(I)-loaded spent grain desorbed in 0.1M Na2S2O3 exhibited higher elution efficiency as compared with other eluants. The results indicated that application of spent grain for adsorption and recovery of silver from aqueous solutions was feasible.

Jan 1, 2009

A slag-metal equilibrium study of the system SnO-FeO-(Si02+Al2O3)/Sn-Fe was carried out at 1250°C. The distribution coefficient, k =(Sn/Fe)metal X (Fe/Sn)slag was found to range from 246 for an iron contentof 0·53 per cenrt in the metal to 82 for an iron content of 6·4 per cent. The value of the ratio ?SnO/?FeO was calculated and found to be approximately a function of per cent SnO in slag alone in the region (Si02+Al2O3)/ FeO = 0·4 to 1·2. Comparison with other published work suggests that the addition of CaO to slags having (SiO2+Al203)/FeO ratios of about 1·1 raises the value of ?SnO/?FeO...

Jan 1, 1974

By Warren E. Morrison

The first major evaluation of the nation's raw materials prospects after World War II was completed by the President's Materials Policy Commission (Paley Commission) in 1952 and submitted to the President in June of that year, as a five-volume study entitled Resources for Freedom. The bulk of the report was devoted to an analysis of the past, present, and probable future of the Nation's mineral supply industries. The Commission's evaluation of the future situation regarding minerals was derived from its forecasts of the probable domestic demand for the major minerals in the 1970's. This demand analysis was made in the context of probable worldwide demand. Several crucial assumptions were made by the Commission's fore-casters. It was assumed in 1950 that the next 20 to 30 years would see no major wars and be a period of sustained economic growth. Another assumption was that the anticipated demand for raw materials must be supplied at essentially no increase in real cost in order to avoid crucial supply problems. The Commission's forecasts were derived within the context of the country's expected future rate of economic activity. The gross national product (GNP) growth to 1975 was derived from projections of the number of people in the labor force, hours of work, and an index of probable production measured per unit of labor input. It was believed labor hours would decrease and labor productivity would increase. The result was a forecast GNP growth rate of 3 percent.

Jan 1, 1970

By Zach Ellis, Dusty Fisher

The Office of Surface Mining, Reclamation, and Enforcement (OSM) cited a large surface coal mine for a series of flyrock incidents that occurred when blasting close to the mining lease perimeter. The OSM placed the company on a pattern of violation status. It was determined through analysis of blasting practices that flyrock could be controlled at the mine by drilling a smaller diameter hole and stemming with crushed rock when blasting within 1,000’ (304 m) of the lease line. The procedure to install and remove the small diameter drill steel was cumbersome and dangerous because it was a manual transition. The drill carousel could only hold one diameter at the time the project was initiated. The process was very time consuming, involving a mechanic to transport the steel to the drill and spend up to 1.5 hours of downtime switching the steel. In addition, the hydraulically operated break-out wrench and break-out fork on the SKS Infinity Redrill® is only designed to work with one diameter, so these tools could not be used to disconnect subs and steels on the string. At the time, the mine’s breakdown was between 30-40% small diameter (6 ¾” (171 mm)) versus large diameter drilling (10 5/8” (270 mm)). The drill and blast group was challenged with the task to implement a 6s (Six Sigma) project that would reduce the amount of time spent on steel change-outs on the rotary drills while improving the safety of the task. A solution was proposed to carry the small diameter drill pipe, lower small diameter sub, and small diameter bit on board the drill at all times. The goal of the project was to carry the steel in the carousel after modification so that the driller could change the diameter himself on board the drill in less than 45 minutes without any assistance from a mechanic. The drill had to be modified so that the hydraulic operated break out wrench and deck fork could be utilized on both diameters. The drill accessory supplier and the mine worked together to design and implement design changes and new equipment onto two rotary drills, and new standard operating procedures (SOPs) were created for the new process. The project has been in the sustaining phase for approximately three months now and all steel diameter changes are completed by the operator under the allowable time limit.

Jan 1, 2015

By P. R. Clifford

Phosphogypsum is a byproduct of the manufacture phosphoric acid. There are approximately one billion tons of phosphogypsum stored in stacks in northern and central Florida. The Florida Institute of Phosphate Research (FIPR) is investigating potential uses of phosphogypsum. These include using phosphogypsum as a road base material, as a soil amendment in agriculture, as a daily cover in landfills, and as a construction material. The results of this research will be presented and will be discussed in light of regulatory barriers to the use of phosphogypsum.

Jan 1, 2002

By Jim Dodd, Jim Paynter

"We would like to acknowledge the efforts of the following key people who helped to make this project a success.Ron Jung, instrumentation supervisor for the Golden Giant Mine, spent many hours reviewing process and instrument drawings, selecting instruments and providing hands on support during commissioning.Andy Keough, underground production supervisor for the Golden Giant Mine, was responsible for readying the underground distribution network for paste backfill.H.A. Simons Ltd. personnel who did an excellent job providing sound conceptual and detailed engineering.Fred Brackebusch, of Mine System Design who designed the paste backfill delivery systemPierre Lacombe, mill superintendent of the Louvicourt Mine, generously shared information and operating experience of their paste backfill plant.AbstractThroughout the 11 year history of the Golden Giant Mine, the primary backfilling method made use of consolidated rock fill. New backfill technologies have developed over recent years which now make it possible to use large quantities of fine mill tailings as backfill.In January of 1996, construction began on a new paste backfill plant at the Golden Giant Mine. Six months following, the plant was commissioned. This paper describes the design, commissioning and operational experience to date of the paste backfill plant."

Jan 1, 1997

By R. Chryst, R. Kus

In the Integrated IT Systems proposed by Przedsie? biorstwo Robót Geologiczno-Wiertniczych—Geological and Drilling Company (PRGW) a network connects a database with all of the departments of a mining division. A key element thereof is the common graphics environment—Micro Station supplied by the firm, Bentley. PRGW’s SoftMine software and GMSI’s CadsMine that are used to design and schedule mining operate in this environment. The digital form of the design project facilitates the verification of information and the integration of technical solutions with SAP R/3 type financial—accounting systems. The system has been successfully implemented in the Brown Coal Mine in Poland.

Jan 1, 2003

RISKGATE is an interactive online risk management system developed by the Minerals Industry Safety and Health Centre (MISHC; University of Queensland) to maximise health and safety performance in the mining industry through implementing continual improvement in management of major unwanted events. A comprehensive knowledge base has been captured for risk management of tyres, collisions, fires, isolation, strata underground, ground control open cut, explosions, explosives, manual tasks and slips/trips/falls. This will be extended to outburst, coal burst and bumps, interface displays and controls, tailings dams and inrush in 2013. RISKGATE presents substantive and leading edge controls to assist industry stakeholders in the design, management and reporting of organisational and regulatory compliance requirements. From a broader industry perspective, RISKGATE provides an environment for knowledge capture and knowledge exchange to drive innovation and best practice in the identification, assessment and management of risk. By capturing operational knowledge from industry experts, RISKGATE provides a cumulative corporate memory at a time of high personnel turnover in the coal industry. All major Australian mining companies are contributing topic experts to this broad industry initiative. In the first 24 months, nine coal mining companies nominated over 80 different experts who contributed over 400 days of individual time to the knowledge capture workshops. RISKGATE is the largest single Australian Coal Association Research Program (ACARP) occupational health and safety (OHS) initiative to date.

Aug 1, 2013

By Farzad Khodabakhshi, Adrian P. Gerlich

"Multi-pass friction stir processing (FSP) was performed to fabricate a new Al-Mg-Graphene nanocomposite. Microstructural developments and distribution of graphene were studied by using electron backscattering diffraction (EBSD) and transmission electron microscopy (TEM) analysis. In the stirred zone (SZ), grain structure was refined down to about 2 µm attributing to the operative dynamic restoration mechanisms and the locking effect of graphene phase. As a result, the yield strength of Al-Mg alloy was improved more than two times due to incorporation of graphene nano-sheets. Also, the indentation hardness resistance of nanocomposite was increased up to ~60%.INTRODUCTION Aluminum-matrix nanocomposites have garnered significant in recent years due to their superior performance and potential advantages for several industrial applications including the automotive and aerospace sectors. Among various reinforcing nano-materials, carbon-based structures featuring sp2 or sp3 hybridization bonds have been found to offer considerably improved physical and mechanical properties. Such carbon allotropes form at micro- and nano-scales including; graphite, carbon nano-tube (CNT), nano-fiber, and graphene. The potential of two-dimensional (2D) carbon materials was introduced in 2004, with the development of graphene as an alternate 2D allotropic form of the carbon structure with a honey-comb lattice at the atomic-scale. It has been shown that it is currently among the strongest materials ever tested with an intrinsic tensile strength of 130 GPa and Young’s modulus of 1000 GPa, and also offers unique thermal and electrical properties.To fabricate metal-matrix nanocomposites reinforced by graphene nano-sheets with typical metallurgical processing techniques, some attempts have been reported in the literature for various solid-state techniques including; hot rolling, mechanical alloying, and friction stir processing (FSP) of pre-cast plates or surface dispersed graphene oxides. The main challenge in those methods was to facilitate the considerable high temperature and pressure for attaining a uniform dispersion of the nano-sheets during the consolidation process. In most cases, significant difficulties have been reported in obtaining a uniform dispersion of graphene within the metal matrix. Among various techniques for production of metal-matrix nanocomposites, FSP has attracted significant attention as a method of surface modification since it was first reported by Mishra et al. In this process, a non-consumable rotating tool is plunged into the surface of material for the aim of microstructure modification. Extreme material plasticity is induced without melting as a result of friction between the tool and workpiece. Frictional heating and severe plastic deformation induced by the FSP process enables metal matrix nanocomposite fabrication by softening the base material and mechanical stirring to disperse the reinforcing nano-materials into the matrix."

Jan 1, 2017

By Radford B. Langston, John A. Marjerison, Graham C. Howell, Hendrik A. D. Kirsten

Probabilistic design is gaining wider acceptance in the rock engineering community since it allows more rigorous determination of risk relating to ground fall or excavation instability. Risk analysis can be conducted by various means, but the basis is formed by either objectively or subjectively determining probability of occurrence of an event. In the case of rock engineering, this event is either instability or excavation failure. Rock mass classification systems provide objective analysis of data collected on a typically subjective basis that also relate closely to excavation stability. A probabilistic analysis technique is presented that uses statistical distributions of rock mass and material properties, ground support fixture specifications, stress conditions, opening geometry, and ground support installation quality to more rigorously determine probability of failure for an underground opening and the subsequent risk to personnel.

Jan 5, 2007

Your assessment of the minerals business. The global mining industry is strong. I am convinced it will continue meeting the mineral needs of the world population for the foreseeable future. Two developments have greatly enhanced the industry’s ability to produce low-cost minerals. Technological innovations have resulted in increased productivity. And there has also been a dramatic expansion of the number of favorable countries in which to explore and mine. Capital expenditures have flowed to the low-production-cost mines and development projects as well as to the exploration projects and stable countries having the best potential for valuable mineral discoveries.

Jan 1, 2000

By David B. Burrows, Francis R. Conley

INTRODUCTION A prerequisite to the evaluation and management of oil properties is accurate information derived from the analysis of core samples; but reliable data, such as porosity and permeability, can result only if all oil and water have been removed from the core samples analyzed. The most common method of core cleaning used to date has been Soxhlet extraction—a somewhat static technique, which depends upon the slow diffusion of hot solvent through the core sample. Soxhlet extraction performs satisfactorily only with highly permeable samples and at best requires long cleaning periods. The centrifuge method was developed in 1951 by Continental Oil Co. to overcome the inefficiencies inherent in the Soxhlet method. The new method is basically an operation in which hot solvents are caused to flow through the samples under the influence of centrifugal force. The centrifuge unit has proved so successful that samples which formerly required days for partial extraction can now be completely cleaned in approximately one hour. The original idea was conceived in 1950 by Elmer S. Messer, whose early experiments consisted of flowing solvent over sandstone samples suspended in a revolving basket and driven by a vertically mounted vacuum cleaner motor. Results were so outstanding that more permanent units were constructed. A modified model using this basic design was recently built by Core Laboratories, Inc., and is now used regularly in their operations. DESIGN Fig. 1 shows a photograph of the two extractors routinely used to clean small core plugs in the Production Research Div. of Continental Oil Co.'s Ponca City laboratories. For illustrative purposes, the basket from one of the units has been removed, and because both extrac- tors are of identical design only one is described in the following discussion. Each extractor unit consists of a centrifuge and a solvent still. The core basket of the centrifuge is made of mild cold rolled steel 7 1/2 in. in diameter and 1 1/8 in. deep. The basket holds 18 1-in. samples (cubical or cylindrical) and is attached directly to a cone fitted to the shaft of the motor. Both the outer rim and the hollow hub of the basket contain perforations for the passage of solvent and extract. The solvent is delivered to the perforations by means of a copper tube inserted into the hollow hub. The motor is a vertical tool post grinder motor; (115 v, 5.6 amp, 0-60 cycles, AC-DC, rated at 1/3 hp). It has a rated speed of 10,000 rpm under full load and 15,000 rpm with no load. Variation of speed is obtained by the use of a variable transformer. The solvent still was constructed from one end of a stainless steel oxygen bottle by inserting a heating element, sight glass, and piping as shown on the schematic diagram, Fig. 2. The heater used was a three-position, 1,000 w, 115-v, immersion type. Intermittent flow of solvent to the centrifuge is obtained by means of a siphon bottle inserted between the condenser and the centrifuge.

Jan 1, 1957

By Ilpo O. Auranen

Background: Mines of today are moving ever increasing tonnages of rock. The new ore bodies tend be of lower grade and located deeper in the earth?s crust. The industry?s focus to overcome this ?deeper but poorer? ore problem has traditionally been to lower the costs by increasing the scale of mining. This has resulted in an ever increasing size of mining equipment like drills, loading shovels, dump trucks. The main focus has been in reducing the cost per ton of mining. This cost focus has often resulted in increased waste rock dilution and more ore losses. From costs to value: Waste rock dilution means waste rock in the concentrator feed. It?s value in open pit mining is equal to the value of ore it replaces. In underground mining, waste rock dilution?s value is equal to the value of ore it replaces added to the costs of mining it. It is commonly accepted that waste rock dilution in open pit mining ranges between 5 and 20% and in underground mining between 5 and 40 % . In a typical large open pit mine ore value is from 20 to 60 USD per ton and mining costs are 1 to 3 USD per ton. One percentage point reduction in waste rock dilution represents savings corresponding to about 20% of total mining operation costs. The difficulty of reducing waste rock dilution comes from the complicated nature of the ores. Accurate ore waste-border detection has not been possible due to excessive costs. Core drilling combined with geochemical lab analysis is the most accurate method for locating ore waste borders. However, it is also expensive and time consuming, which is why it is often combined with somewhat lower cost methods like sampling drill cuttings from blasting drill holes or from reverse circulation drills and analyzing them in a laboratory. The main drawback with these methods, in addition high costs, lies in the sampling accuracy and in the quality control of the whole process when a large number of samples have to be handled manually. In every mine it is possible to halve waste rock dilution by using new on-line analysis technology .

Oct 1, 2009

By Makoto Kimura

Failure tests on laterally loaded single and pile group are analyzed with a 3-dimensional elasto-plastic finite element program. In the analysis, the mechanical behavior of the ground is supposed to be elasto-perfect plastic with Drucker-Prager's yielding criterion. The nonlinearity of the piles is simulated by assuming a hyperbolic relation between the bending moment and the curvature of the piles. The influence of the axial stress on the cast-in-place concrete piles is also considered in the numerical analysis. It is found that the mechanical behavior of the piles subjected to lateral loading, such as the load-displacement relation up to an ultimately large deformation, and the distribution of bending moment in the pile group can be well simulated.

Jan 1, 1996

By Tara Bajpayee

Modern, highly productive underground mining operations need to assure the safety of their workforce by understanding where major strata fractures and roof failures could occur. Mines depend on a host of tools to assess ground instability. In-mine microseismic monitoring systems with sufficient number of sensors have also been used to provide this information. These in-mine systems must be robust in design and moved regularly to keep up with the mining advancement. System performance issues depend on maintaining ever increasing cable runs, preventing component damage from mining activities (scaling, blasting, etc.) and avoiding signal degradation due to interference from mining equipment (fans, trucks, electrical equipment, etc.). A potential solution is to use a surface based monitoring system having sensors placed in boreholes above and adjacent to the underground mine workings. These sensors must be capable of detecting and locating strata fracturing associated with rock failure events. A great advantage of a surface based monitoring system is its independence from the underground mine infrastructure. There is less concern with cable maintenance problems, signal degradation by interference from mining activity, or loss of power from the mine?s power grid. The disadvantages include the cost of drilling boreholes and challenges associated with placing sensors in the boreholes, maintaining radio communication and solar power, and public interference (vandalism, etc.). This paper describes a case study where a surface based microseismic system, using triaxial geophones in boreholes drilled from the surface, was deployed at a large limestone mine. The system was operational during a roof fall that occurred in October 2007. It detected the first rock fracture event 17 minutes before the rock fall event. The geophone array was sensitive enough to identify all large rock fracture, impact, and blast events as well as medium size rock fracture events occurring close to the geophone array.

Jan 1, 2008

By Richard S. Watt

The Bureau of Mines is often called upon to analyze the demand for various minerals and fuels and to make projections of the future demand. Because minerals and fuels are raw materials and because the demand for raw materials [pends] on the demand for finished goods, these projections are usually [conned] with derived demand rather than final demand. In order to obtain quick [d] reasonably accurate analyses of the demand for mineral commodities, the [reau] developed a method and has used it successfully (31).4 To illustrate the [thod], this report presents a full analysis of the demand for a mineral commodity with enough general theory to permit application of the method to any mineral. Sodium chloride (common table salt) was chosen as the subject of the analysis because the demand for it is less complicated5 and permits a simple application and clear presentation of the method.

Jan 1, 1962

By A Vigar

Siliceous float sampled in the Wafi River by CRA Exploration in 1977 assayed 22 g/t Au and 89 g/t Ag. Follow up in 1979 led to the discovery of outcropping mineralisation now known as Zone A. Soil sampling in 1980 and 1982 outlined a 350 m by 400 m area of >1 g/t Au at Zone A and smaller areas at Zones B, C and D. Thirty-one diamond holes were drilled between 1983 and 1986. Elders Resources continued evaluation of Zone A under a farming agreement between 1988 and 1990. Mineralised diorite porphyry was discovered in 1990 by drilling conceptual targets 500 m to the NE of Zone A. Evaluation of this copper-gold porphyry became the main focus of exploration for the next five years and a substantial resource was outlined within a single, discrete body. A review of the paths to project development in late-1995 highlighted the need for increased resources via a second mineralised porphyry and/or an additional resource of Zone A size to make the project viable. It was concluded that the greatest immediate potential for increasing the resource inventory was at Zone A itself where the mineralisation was open in all directions. Detailed mapping and drill core logging lead to the geologic and structural models being revised in early-1996. The objectives of the 1996 drill program were to extend the Zone A resource, to test for continuity of mineralisation westwards to Zone B, to better define the controls on gold mineralisation and to delineate high-grade blocks amenable to selective mining by infill drilling and 3D orebody modelling. The last drill hole of 1996 intersected 30 m at 4.6 g/t Au from 273 m in WR147, deep in the western limit of Zone A. This intersection gave impetus to continue drill testing towards Zone B. In April 1997, hole WR154 was drilled 100 m to the west of WR147 and intersected 20 m at 8.5 g/t Au and 70 m at 11.0 g/t Au at similar depths near the diatreme contact. Drill hole WR155 was then drilled 100 m to the west of WR154 and intersected 86m at 5.7 g/t Au and WR159 drilled 100 m to the south of WR154 intersected 36 m at 9.2 and 50 m at 4.4 g/t Au. A significant zone of essentially blind, high-grade gold was discovered beneath the dipping flank of a poorly mineralised diatreme in what became known as the Link Zone. The long history of evaluation has been driven by the conviction of a dedicated team that a mineralised system of the size and complexity of Wafi with strongly anomalous gold in outcrops over the entire Mount Golpu area must contain economic mineralisation hidden within it. The keys which redefined the direction of exploration and lead to the discovery of the blind, high-grade gold Link Zone were, in our view, the critical review of the project status, detailed geological and structural studies to define clear exploration targets and the necessary funding and persistence to carry this through.

Jan 1, 1999

By R. R. Sayers

"The number of investigations reported during the past year indicates that control of the health hazard due to abnormal air conditions is still a matter of serious consideration in the mining, metallurgical, and allied industries.Australia. - In an investigation into the health and working conditions of employees in the mining industry of Tasmania and Victoria3, it was found that although pulmonary tuberculosis may occur early in life, silicosis is e disease of slow evolution and does not appear frequently under the ace of 40. A period of at least ten years in the industry was found necessary to produce silicosis, and in no case was the disease found in those who had not worked underground. A very high incidence of silicosis was found in all fields among those who had worked underground 20 years and longer. There was some evidence that silicosis complicated by tuberculosis may occur earlier than uncomplicated silicosis.England. - In a paper presented before the Section on Occupational Diseases of the British Medical Association, Dr. E. L. Middleton, the medical inspector of factories, called attention4 to the occurrence of silicosis in various industries throughout the country.punitive on some quite harmless industries. Thus Middleton says: ""Where the amount of dust is small the action of the phagocytes is likely to be effective, but where it is great . . ."" What dosage is indicated by ""small"" and ""great"" in this connexion? If the meaning of ""small"" were known, would it be correct to go on to say, as he does, ""each successive dose of silica produces a summation of effects""? Then, again, would it be fair to say ""a comparatively brief period of exposure may be the only determining factor""? What, in minutes, hours, or days per week, per month,' or year, is intended by ""a comparatively brief period""? ""Intermittency of the process"" is another expression used in summing up the reasons for and against a standardization of air purity by a gravimetric process or enumeration of the particles; the arguments against such a standardization are, by Middleton, considered strong, but they are by no means convincing to us. A standard has been accepted in respect of the amount of lead in milligrams per 10 cubic metres of air; Dr. Ronald Lane showed in another paper read that adherence to this makes the occurrence of poisoning highly improbable. Mavrogordato has placed on record figures of silica dust at different stages of the improvements in the workings of the Rand mines, and such a control is in constant operation in them today.We emphasize these points because apparently the Government has taken the unusual course of legislating first and postponing inquiry to a later date, as in the ""Various Industries (Silicosis) Scheme, 1939."" The insurance companies also have a considerable interest in the matter of compensation for the silicosis risk. Where exposure - as in the refractories industries, the grinding industries, sandstone industry, and pottery industry - is day in and day out, they rightly demand a premium far higher than for any other disease scheduled under the Workmen's Compensation Act - 5 per cent on the wages bill. row every industrial employer, such as the paint and varnish manufacturer, who has a sack of crushed silica in his store .room, from which he extracts once a week enough to make a paste With spirit and add to his other ingredients in order to give them the necessary ""bite,"" becomes involved, and may have to abandon the use of the material or pay 8 per cent on his wages bill for an absolutely negligible risk.. For meting out justice standardization seems urgently called for."

Feb 1, 1930