Search Documents

A pilot program was undertaken to evaluate a process developed by the U.S. Bureau of Mines to recover nickel, cobalt, copper and chromite from domestic nickel laterite resources. An existing five ton per day pilot plant was modified to accommodate treatment of laterite by the Bureau process, which employs reductive roasting, ammoniacal sulfate leaching, solvent extraction, and electrowinning to extract, separate, and recover nickel, cobalt and copper as high purity cathode products. Three distinct types of laterite i.e., limonite, saprolite and a mixture of limonite/saprolite were processed through the plant during three operating campaigns. Nickel cathode was made during all three campaigns, while cobalt cathode and chromite concentrate were recovered only during processing of limonite. Leach extraction of nickel and cobalt averaged 83 and 67 percent, respectively, while the overall recovery was 80 and 63 percent for nickel and cobalt, respectively. Initially, over-reduction of iron in the saprolitic calcine contributed to poor settling of the leached solids. This problem was overcome by careful control of reducing conditions and flocculant addition. An economic feasibility study was made for a 5000 TPD grassroots laterite processing facility scaled-up from pilot plant data. Estimated (+ 30) percent capital cost for a Nine and plant is $367 million with an estimated $103 million per year operating cost. The study indicates that low-grade domestic laterite may he processed with marginal profit- ability.

Jan 1, 1982

By Mick Fritz, Tom Treleaven

The success of any blast is dependent on the accuracy of the blast design and field controls placed at the shot location. The procedure by which the data is collected and analyzed is paramount to accomplishing the anticipated blast results. lf the geometry of the blast is not measured correctly, then the results will not meet expectations. Measuring the geometry and compensating for bole hole deviations is crucial not only to the lnitlal blast but also for any consecutive blasts. Excessive bore hole deviation can cancel any new technology in use. However the instruments and skills required solving this Issue are readily available.

Jan 1, 1998

By W. T. Adams

The production of natural abrasives var¬ied in quantity and value compared with 1975. Output of tripoli-type materials and garnet increased in both quantity and value; special silica stone products decreased in quantity and increased in value; the production of emery decreased. The production and value of manufactured abrasive materials increased for all types. [ ]

Jan 1, 1978

By R Edwards

Greater efficiency of capture of minus 6 mm to fine micron size particles of free gold is achieved with the Knelson Concentrator. The development, principles of operation and recent innovations relating to this enhanced gravity concentrating device are described by the inventor, followed by a description of application and consequent economic benefits in low grade alluvial gold deposits by a large scale user of Knelson Concentrators in the Northern Territory of Australia.

Jan 1, 1990

By K. Zabrusky

Estimation of high grade epithermal vein deposits can present challenges in correctly representing the continuity of grade within an undulating structure. One solution to this problem is to use dynamic anisotropy to follow local variations in the strike and dip of veins. Dynamic anisotropy (D.A.) allows the search parameters to change block by block throughout the model to account for the local variations. Presented here is a study of a vein that changes orientation down-dip. A traditional resource estimate using one search ellipse orientation was performed. The resulting estimated grades did not accurately reflect those of the sample data. Using a search ellipse with an average value for the two distinct dips caused the grade estimation to be less representative than desired. Rather than performing domain-based analysis with different search ellipses, the issue was corrected by using Datamine Studio 3?s D.A. function. The 3D vein trend was used to estimate the dip and dip direction of the vein in each block. The resulting D.A.-estimated model follows the two dip trends of the vein. This software makes a previously tedious task faster, and allows for more accurate estimations.

Feb 27, 2013

By John J. Sammarco

Mining has one of the highest annual average fatality rates among major US industries. Health and safety dangers have been inherent to mining since the early days of picks and shovels. Even though miners’ health and safety has improved over the years, mining is still one of the most dangerous occupations. Mining was traditionally a low tech industry. It is now driven by competitive pressures to go high-tech by using programmable electronics (PE) for machine control, atmospheric monitoring and material processing. The industry’s experience with the functional safety of PE is limited compared with other industries. Thus, PE is an emerging technology for mining that can potentially create or worsen hazards.

Jan 1, 1999

By Verne E. Hooker

This Bureau of Mines report summarizes the results of modifications in the borehole deformation gage design and subsequent changes in the overcoring techniques. Modifications in the borehole deformation gage have greatly improved the creep characteristics and enhanced the versatility of the gage. In situ field tests in competent rock near St. Cloud, Minn., provided sufficient data to compare the reliability between gages and new techniques in obtaining good engineering estimates of stresses. Near-surface horizontal stresses at the test sites are compressive and biaxial in nature.

Jan 1, 1974

By Gregory Poole

With access to the World Wide Web, many resources are readily available for improving claim reports. With a little time spent on line, a more thorough report can be created. Claimants will accept the conclusions of a report more readily when they can view support information on their own computer, particularly when the support information is not just from blasting related web sites. Some suggested resources are discussed including aerial pictures, local tax maps, topographical maps and home repair web sites. This paper provides suggestions for tracking down support information on the web and information on how to properly reference this information. Case studies of several claim investigations are presented. These are some examples of how a little time spent online provided clear and convincing evidence to support the conclusions of the investigation.

Jan 1, 2006

By E. R. Maize

This report is the second of a series on roof movement in coal mines. The first (R. I. 3355)4/ dealt with convergence of roof and floor and movement of the surface accompanying and following extraction in a mechanized mine in which retreat of rib lines was rapid. The studies reported herein were made in a mine in which all the coal is loaded by hand, and movement of the rib lines was much slower in consequence. In choosing a site for this work, it was decided that the mine selected should have natural conditions akin to those of the first study and entirely different methods of working. To this end a cooperative agreement was made with the Crucible Fuel Co. through W. J. Whitaker, secretary, for conducting the work in the company's Crucible mine, operating in the Pittsburgh bed in Greene County, Pa. This paper gives an account of the methods used in the investigation, excerpts from the data obtained, and such generalizations as can be made.

Jan 1, 1939

By Alan J. Zeni

Drainage of water from abandoned underground mines has become important in recent years because of safety concerns when mining near abandoned works or reentering abandoned mines for further development. Seepage from inundated mines causes environmental damage and may threaten homes and communities. Where topography permits, horizontal drilling can provide a quick and cost effective method for solving trapped water problems. The mechanics of the horizontal drilling operation as applied to water drainage are discussed in this paper.

Jan 1, 1990

By H. Jalkanen, L. Holappa

The main role of slag in oxygen converter processes is to absorb the non-volatile oxidation products of hot metal impurities, Si, P, Mn, Ti, V, etc. The importance of converter slag as deP and de Smedia has ceased with implementation of special pre- and post-converter treatments. The transfer from top blowing (LD) to combined blowing converters has decreased the amount of slagged iron that, together with the tendency towards lower silicon and manganese contents, has decreased slag to steel ratio. Still the control of slag forming and behaviour during the blow is of great importance. In this paper the thermodynamics of the slag forming reactions, the role of slag in the modern oxygen converter process for impurity elimination, splashing, lining wear, dust formation and post combustion are discussed on the basis of common knowledge and experience of Finnish steel plants.

Jan 1, 2004

By E. R. Maize

This report is t e second of s series on roof movement in coal mines. The first (R. I. 3355)4/ dealt with convergence of roof and floor and movement of the surface accompanying and following extraction in a mechanized mine in which retreat of rib lines was rapid. The studies reported herein were made in a mine in which all the coal is loaded by hand, and movement of the rib lines was much slower in consequence. In choosing a site for this work, it was decided that the mine selected should have natural conditions akin to those of the first study and entirely different methods of working. To this end a cooperative agreement was made with the Crucible Fuel Co. through W. J. Whitaker, secretary, for conducting the work in the company?s Crucible mine, operating in the Pittsburgh bed in Greene County, Pa, This paper gives an account of the methods used in the investigation, excerpts from the data obtained, and such generalizations as can be made.

Jan 1, 1939

By Philip K. Hopke

A systematic study of the mechanism of interaction of 218Po(RaA) armed by the decay of 222Rn with airborne particulate matter has been made. The rate of attachment of RaA to particles in the diameter range of 0.1 µm to 10.0 µm has been measured as a function of particle size, concentration, and composition, radon concentration, time of interaction, relative humidity and temperature. It was found that under the conditions in these experiments the attachment rate was proportional to the square of the particle diameter and varied with temperature and relative humidity. The composition of the particles apparently has no effect on the attachment. The variation in attachment rate was related to a sticking probability coefficient of approximately 0.02 that varies systematically with temperature and humidity. In addition, the rate of deposition of RaA on the wall of the attachment kinetics system was measured and also found to change with temperature and relative humidity.

Jan 1, 1980

By D. Babich, L. Alcorn, E. Spencer, A. Smith

Noise is one of the most pervasive health hazards in mining. A compilation of Mine Safety and Health Administration (MSHA) noise survey data for Fiscal year 1990 shows that approximately 40% of the total samples taken for longwall occupations exceeded the Permissible Exposure Limit (PEL) of 100% [Gigliotti et al. 1991]. In order to properly determine workers’ exposures on longwall coal mining systems, it is necessary to provide accurate baseline measurements for these mining systems. This research was designed to develop guidelines and test procedures for identifying all noise sources that are major contributors to the underground noise exposure of longwall coal mining system workers. Once the high noise sources are identified, promising engineering controls can be tested and evaluated to reduce the noise of the sources. The measurement system used to analyze the noise sources included stationary dosimeters in a documented repeatable pattern and a time-motion study of the cutting cycle and operator’s work cycle. Significant results from the underground measurements show that the highest sound levels recorded are at the stageloader discharge segment and tailpiece controls and remained at about the same level throughout the test.

Jan 1, 2007

By Lucia Kuizon

The Miranda Pine Roadless Area Review and Evaluation (RARE II) study area (No. 5114) comprises 12,600 acres (5,100 ha) in Los Padres National Forest in Santa Barbara County, California, about 15 mi (24 km) east of Santa Maria (fig. 1). Mineral investigations are made by personnel from the U.S. Bureau of Mines on National Forest lands identified as Further Planning Areas in the RARE II program. The Bureau of Mines reviewed literature, mining claim records, and production files; examined the study area; and sampled mineral properties where appropriate.

Jan 1, 1983

By M. A. T. Cocquerel, M. G. Burcher, J. G. Eacott

"This paper is based on work carried out to examine the feasibility of increasing the smelting rate of two oil-fired calcine-charged reverberatory furnaces . Various constraints prevented physical enlargement of the furnaces and so allention turned to the use of preheated combustion air or oxygen enrichment to bring about the required increase in production. As a basis for further calculation, a furnace heat balance is determined using the smelting metallurgy and combustion data for the current operation. Various other operational data are tabulated and compared with similar data from other operating copper smelters.New heat balances are derived for various levels of combustion air preheat at the current smelting rate, and the effects of air preheat on oil consumption, combustion air and waste gas volumes are tabulated. These data are used to demonstrate the level of increased throughput which would be obtained before constraints in existing gas handling equipment are encountered.A similar exercise for oxygen enrichment is set out, with oil consumption, combustion air and waste gas volumes at various enrichment levels tabulated for the current smelting rate. These data are in turn used to demon strate the smelting rate which would be achieved at a practical level of enrichment before waste heat boiler and gas handling constraints are encountered.The energy implications for both cases are summarized."

Jan 1, 1980

By Bruce I. Thomas

[THIS PAPER, tine of a series on placer ml n in iii Alaska, describes mining methods and gives unit costs at operations where hydraulic and mechanical excavation equipment is used with nonfloating washing plants. The mining methods described were developed during the last 30 years to copy with conditions peculiar to arctic and subarctic regions arid are now used by a large segment of the placer mining industry in Alaska. The operations described have been classified if m ii into three main categories: Those having sluices at a bedrock level, those having sluices above bedrock and those having mobile nonfloating washing plants (dryland dredges). Diesel-powered bulldozers and draglines convey or clevate gold-bearing gravel to the sluices, remove tailings, and strip waste gravel and other overburden. Diesel-powered centrifugal pumps supply water foe sluicing and hydraulic stripping. Detailed descriptions and unit cost arc presented for 14 operations to illustrate the numerous arrangements udder the first 2 categories.]

Jan 1, 1959

By W. Blake, J. Whyatt

Sixty years of rockbursting in the Coeur d’Alene district has taught painful lessons and led to a number of practical advances in controlling rockburst hazards. This paper summarizes those lessons, concentrating on practical measures that have been successfully adopted to reduce hazards. These lessons are explained in the context of district mining history and current understanding of rockburst phenomena. Overall, the paper provides the practicing mine engineer with an appreciation of rockburst hazards and an overview of practical measures that can be used to control these hazards in the context of Coeur d’Alene district experience.

Jan 1, 2002

By Poi G, Madgwick J. C, Davis P, Pannowitz D, Cho D, MacKay B, Chan S. M, Varga R. A, Chun U

Periodic dilute sulphuric acid treatment ofstill, batch-fed, molassesenriched, microaerobic, manganese-dioxide-Ieaching microbial cultures led to marked improvements over untreated cultures. Percentage Mn++ recoveries increased (7X), rate of Mn++ formation improved (3X) and yields of Mn++ per molasses use were more economical (5 X). The yield in terms of molasses used improved with decreasing sugar used (eg 1.17 g Mn++/gram molasses at 0.2 per cent molasses (w/v) feed and 24 per cent (w/v) pulp density MnO2 tailings). The most effective Mn++ leaching in terms ofpercentage recovery (97 per cent) and rate ofleaching (46 mg Mn++/day) was at 0.5 per cent molasses (w/v) and 14 per cent pulp density (w/v) MnO2 tailings.

Jan 1, 1986

By R. F. Chaiken

The Bureau of Mines has carried out experimental and theoretical studies with prilled and pulverized ammonium nitrate-fuel oil (AN-FO) mixtures containing varying amounts of fuel oil in an attempt to quantify the effects of stoichiometric composition, nonideal detonation behavior, and expansion volume on the production of CO, NO, and N02 fumes. Experimental fume measurements were obtained in the Bureau's large closed gallery facility (7.2 X 104 liter expansion chamber) and in the standard Crawshaw-Jones apparatus (90--liter expansion shamber) using a prepackaged charge configuration containing about 450 g of explosive.4 The theoretical calculation of toxic fumes was achieved with an equilibrium detonation code called "TIGER,," Contrary to initial expectations, the NOx (= NO + N02) fumes from the large gallery test were found to be in essential agreement with the Crawshaw-Jones results. It was also concluded that (1) "TIGER" calculations offer a good approach to the prediction of toxic fumes; (2) there is a basic problem in extrapolating laboratory measurements of CO fumes to mine conditions--this being due to postdetonation oxidation of CO to CO2; and (3) the detonation velocity decay rate of an explosive is a useful experimental parameter for correlating toxic fumes production with nonideal detonation behavior.

Jan 1, 1974