Search Documents

By Peter A. Oshust

The EKATI Diamond Mine has successfully completed the development and commissioning of the Panda Underground Project to extract the ore below the Panda open pit. The dominant kimberlite domain of the Panda Underground, intermixed olivine-rich and mud-rich resedimented volcaniclastic kimberlite (RVK), is very similar to the kimberlite domain characterizing the open pit portion of the pipe. A sublevel retreat mining method is in operation underground at Panda; near-vertical blast rings are drilled and blasted into an open void. Broken ore is mucked with load, haul and dump trucks (LHD?s), sized underground then moved to surface through a conveyor system to the process plant. An advanced feasibility study is in progress at the Koala Underground Project. The Koala pipe is geologically more complex than Panda. The pipe below the open pit is comprised of at least five distinct kimberlite domains. There is a 100 m thick zone of incompetent low-grade mud-rich RVK between the open pit and the stable high-grade olivine-rich primary volcaniclastic kimberlite where mining will be initiated. As a result, it is proposed that Koala will employ sublevel caving; each blast ring shot would be confined and mucked in sequence to maintain the cave of the over-lying low-grade RVK ore. The sublevel cave method seeks to safely defer the mucking of the low grade ore to the latter part of the mine life.

May 1, 2006

By J. -W. Kim, Y. -B. Kang, H. -G. Lee

The effect of SiO2addition on the decomposition of Li2CO3was investigated at temperatures up to 1000ºC. It was found that addition of SiO2greatly enhanced the decomposition of Li2CO3. The main decomposition reaction started at around 600ºC, and completed just above the melting point of Li2CO3. The major decomposition product was Li2O?SiO2irrespective of the Li2CO3to SiO2mixing ratio while both reactants were available. It was ascertained that a liquid layer betweenLi2CO3and SiO2particles formed and facilitated the decomposition reaction. The governing reaction of the decomposition was the one between the dissolved Li2CO3and SiO2in the liquid layer to form Li2O?SiO2. The decomposition rate was independent of the Li2CO3/SiO2mixingratio until either one had been completely exhausted. When excess Li2CO3existed, it further reacted with the initial product of Li2O?SiO2to form 2Li2O?SiO2. When SiO2was found in excess, on the other hand, no further reaction took place. This is attributed to the fact that uponLi2CO3exhaustion there is no liquid phase available to facilitate further reaction. The apparent activation energy of the decomposition of Li2CO3in existence with SiO2is 198 kJ mol-1.

Jan 1, 2004

By Jamal Rostami, Ebrahim Farrokh

Selection of tunneling method, specially the use of shielded machines for application in deep rock tunnels can be heavily impacted by presence of ground convergence and squeezing conditions. Tunnel convergence is a function of ground conditions (i.e., rock mass behavior, groundwater, in-situ stresses), size of the opening, and TBM operational parameters. The case study of Ghomroud water conveyance tunnel project in Central Iran, which is under construction using a double shield TBM, is used to examine the effect of rock parameters on tunnel convergence and hence on the need for over excavation and shield lubrication to avoid problems with the shield getting stuck. Although it is impractical to perform a continuous assessment of rock mass conditions within the shield or in the lined tunnel, results of field observations and subsequent studies show that the amount of the tunnel convergence has direct correlation with the percentage of fines and large rock fragments in the muck and TBM thrust/torque/ROP. These relationships have been examined and will be presented in this paper.

Jan 1, 2007

By J. Wennerstrand

Slender steel piles have found an increased use in Sweden in resent years. These piles are often driven throw soft normally consolidated clay to refusal in till or at the rock surface. In contrast to most other piles the bearing capacity with regard to failure of the shaft is in many cases smaller than the bearing capacity with regard to failure of the soil or rock at the lower end of the pile. Imperfections such as deviations from a straight line of the pile centerline and residual stresses in rolled and welded profiles are important for the capacity of the pile shaft. Even thow the second order moment caused by initial deviations in piles is only half of that in a column with the same slenderness, imperfections can and should be accounted for in much the same way as for columns.

Jan 1, 1989

By G B. Gnoinski

The Skorpion Zinc Mine and Refinery is situated approximately 25 km north of Rosh Pinah, south-western Namibia. The supergene zinc oxide deposit at Skorpion is hosted in a volcano-sedimentary succession within the para-autochthonous Port Nolloth Zone of the Gariep Belt. Rock types hosting the ore deposit include altered and metamorphosed volcaniclastic and clastic sediments, limestone and rhyolite. At Skorpion, the metallurgical process is unique and the plant design requires minimal fluctuations within a selected feed grade. In addition, the presence of limestone inter-fingered with ore in some areas of the deposit results in dilution problems which may increase gangue acid consumption and therefore processing costs. Hence, selective mining is necessary to ensure the delivery of suitable ore to the processing plant, in order to keep the overall operating costs at a minimum. A complex control system is in place and is capable of a high degree of selectivity. The paper describes the grade control system in place at Skorpion Mine which ensures that the qualities of the blocks planned for mining and the material being mined meet the stringent process requirements of the refinery, i.e zinc grade, gangue acid consumption and deleterious elements that may impact on the efficiency and costs of the metallurgical process. Keywords: Skorpion zinc, zinc oxide, supergene, volcano-sedimentary, grade control

Jan 1, 2007

By Dennis R. Dolinar, Christopher Mark, Gregory M. Molinda

Despite more than half a century of experience with roof bolting, no design method has received wide acceptance. To begin to improve this situation, National Institute for Occupational Safety and Health (NIOSH) conducted a statistical study of roof bolt performance at a number of mines throughout the U.S. Case histories were collected from 37 mines with a variety of roof bolt types and patterns in a wide range of geologic environments. Performance was measured in terms of the number of roof falls that occurred per10,000 ft of drivage. The study found that roof falls are rare when the roof is strong and the stress is low, even with light roof bolting patterns. The focus of this paper is on the more difficult conditions, where the roof is weaker and/or the stress is higher. Analysis of the results led to guidelines that can be used to make preliminary estimates of the required bolt length, capacity, and pattern. The guidelines are based on the depth of cover (which correlates with stress) and the roof quality (measured by the Coal Mine Roof Rating (CMRR), and the intersection span. Another contribution is a formula for estimating the horizontal stress level in the eastern U.S. coalfields as a function of the depth of cover. The design guidelines are currently being implemented into a computer program called Analysis of Roof Bolt Systems (ARBS).

By J. T. McLendon

As part of its research project in developing improved refractory materials for metallurgical applications, the Federal Bureau of Mines obtained hot modulus of rupture data at 1,500°,1,550°, and 1,600° C on samples of 13 refractory periclase materials produced from seawater, lake brines, and natural magnesite. The periclase samples also were characterized to establish chemical and mineralogical composition and microstructure. The results indicated that a high MgO content does not necessarily assure good hot strength and that an optimum and varying CaO-Si02 ratio exists for each individual periclase sample.

Jan 1, 1979

By Vítor Covre Evangelista da Silva

Esta proposta objetivou desenvolver uma análise teórico/experimental da influência de 2% Ag (em peso) em uma liga de solda Sn-40%Bi solidificada unidirecionalmente em regime transitório de fluxo de calor. Correlações experimentais entre os parâmetros térmicos de solidificação como velocidade de deslocamento da isoterma liquidus - VL, taxa de resfriamento - ?L e parâmetros microestruturais como espaçamentos dendríticos secundários – l2 foram determinados. A caracterização microestrutural foi realizada por meio de microscopia ótica e eletrônica, difração de raios-x, além de fluorescência de raios-x para obtenção dos perfis de macrossegregação dos solutos (Bi, Ag). Para determinação do perfil de dureza foram realizados ensaios de dureza Vickers. As microestruturas brutas de fusão da liga Sn-40%Bi-2%Ag são compostas de dendritas ricas em Sn decoradas com partículas de Bi circundadas por uma mistura eutética (Sn+Bi) e partículas primárias de Ag3Sn. Os parâmetros térmicos decresceram com aumento da camada solidificada, permitindo uma ampla variação: ?L ? 0,1 a 10,0°C/s, VL ? 0,2 a 0,9mm/s e GL ? 0,4 a 11,0°C/mm. O teor de bismuto não variou significativamente, ao passo que a prata variou de forma efetiva, concentrando-se no início do lingote (até próximo de 35mm). O surgimento de braços dendríticos terciários em 15mm conteve a diminuição da microdureza Vickers, esperada para as posições mais afastadas da interface metal/molde.

Aug 16, 2017

By Steve Kral

In the United States, the U.S. Environmental Protection Agency (EPA) is set to implement its Tier 2 air quality standards governing high-horsepower, off-road diesel engines. The regulations take effect in January2006. In Europe, similar standards, called Stages, are due to take effect about the same time. And other markets, such as Japan and Australia, have their own standards on tap. Tier 2 standards will further reduce the amount of nitrogen oxide (NOX), sulfur dioxide (SO2), diesel particulate matter (DPM), carbon monoxide (CO) and hydrocarbons off-highway diesel engines are allowed to emit. And even more restrictive Tier 4 standards are due in 2011. The upshot is that operators of high-horsepower engines, particularly in mining, will begin using in their new off-road haul trucks, excavators, shovels and other mining machines diesel engines that are designed to meet these more stringent standards.

Jan 1, 2004

By M. E. Tyrrell

To promote greater use of abundant domestic raw materials in the manufacture of synthetic mullite, the Bureau of Mines has undertaken a comprehensive investigation to determine the effects of the impurity oxides TiO2, Fe203, and alkali on physical properties of sintered mullite-forming mixtures. The first part of the report presents the results of work covering a major area within the mullite study; namely, the effect of impurity oxides on volume stability, one of the outstanding characteristics of mullite refractories. The volume stability of 20 compositions in each of 3 alumina- to-silica ratios, which blanket the range commonly found in purchase specifications, has been determined following procedures of Navy Specifications B-15606 A for Grade A high-alumina refractories. Results indicated that so long as 5 percent of impurities are combined approximtely in the proportions of 3 percent Ti02, 1 percent Fe203, and 1 percent alkali, sintered mullite-forming compositions in the almina to silica range tested will be volume stable. A permissible tolerance of one-half per- cent in each impurity oxide provides a range that includes values common in the natural minerals from which sintered mullite may be made. Within the total range of 5-percent impurity mixtures, a greater number of volume-stable compositions were obtained by increasing the alumina-silica ratio.

Jan 1, 1962

By M Carr, K Williams, W Chen, J Plinke

The depletion of iron ore deposits at the face of the mine site dictates the necessity for the exploitation of formerly less attractive orebodies to meet the demand of the modern world. These orebodies will typically be found close to or even beneath the water table where an increasing clay and moisture content will result. Problematic iron ores, colloquially termed as ‘wet and sticky’ material (WSM), can have a significant impact in the material handling stream due to the expensive downtime of processing equipment, which is attributed to the inter-particle and boundary cohesion and adhesion forces of the bulk material.In order to gain a better understanding of the causes of poor handleability, experimental test methods to determine wall adhesion, and inter-particle adhesion within bulk materials were developed. Based on the combination of wall adhesion and inter-particle adhesion measurements, with traditional methods of assessing bulk material handleability, a new method to assess the potential of bulk materials to cause handling problems is proposed. This method reduces the multitude of factors leading to problematic behaviour to a handleability index (HI) [0,1], which is easily assessed and understood. The method is suitable for adhesive materials and applicable for a wide range of material flow, from gravity reclaim stockpiles to transfer chutes and carry back on conveyor belts.Additionally, this research presents an assessment of the HI derived by experimental testing of three iron ore samples. A clear understanding of the problematic behaviour of the iron ore samples is achieved with the use of dust extinction moisture (DEM) tests, which indicates the regions where problematic behaviour may be experienced on-site.CITATION:Carr, M, Plinke, J, Williams, K, Roberts, A and Chen, W, 2017. Determination of the handleability index of adhesive bulk materials, in Proceedings Iron Ore 2017, pp 503–510 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By R. J. Latino

Because of the lack of a universally accepted definition or standard for RCA, we are left to our own conventions in the marketplace as to what is most ?effective? or a ?Best Practice? for our own facilities or organization. This lack of uniformity in the application of RCA produces an equal lack of uniformity in the measureable outcomes of RCA on the bottom-line from site to site and industry to industry. What is the definition of success for an RCA? Is it regulatory compliance? Is it some quantifiable measure of bottom-line performance? Is compliance and bottom-line performance the same thing? Can we measure the ROI we receive by doing compliant RCA? These questions must be adequately addressed if any definition of RCA is to be effective on the bottom-line. Like our various Corporate Vision and Mission Statements, what would be our Vision and Mission for RCA? When pondering the answer to this question, we should consider: ? What Key Performance Indicators will the Success of RCA be Linked to? This provides a direct correlation to the corporate dashboard and therefore garners support for the RCA effort when implemented at the sharp end. Not until we know what KPI?s will effectively measure our maintenance and reliability objectives can we begin to establish which opportunities will afford the greatest returns1. ? What Bottom-Line Metrics will be Tracked to Measure the Effectiveness of Our RCA Effort? Will it be increased production, profitability, regulatory compliance, etc.? Will it be decreased injuries/fatalities, claims, customer complaints, risks, etc.? We should be specific about these metrics and their correlation to the metrics on our corporate dashboard. ? What Will Trigger an RCA Investigation? Normally companies will establish quantifiable thresholds to be surpassed before an RCA will be conducted. Examples may be an OSHA recordable injury, a failure event in which production losses exceed $250,000, an equipment failure in excess of $50,000 or a regulatory violation. This is the norm. However, we should realize this is using our RCA skills totally on a reactive basis. High Reliability Organizations (HRO) strive for proaction and they also use RCA proactively. Why can?t we use RCA to analyze why unacceptable risks from an FMEA are so high? It is perfectly applicable yet rarely implemented in this fashion.

Feb 27, 2013

Newmont Waihi Operations is participating in the initiation of a community liaison forum in association with the local district council. The objective is to provide a forum for the free and regular exchange of ideas, concerns and information, and through improved communication seek to achieve a more comprehensive set of solutions to community, operating and closure issues associated with Martha Mine. A similar liaison forum has been operated on two previous occasions during earlier phases of the present mine's operation. This paper deals with the practical aspects of setting up a liaison forum to act as an effective conduit between regulators, mine operators, local businesses and the community. The mechanisms and procedures for identifying community issues and concerns are dealt with. The actions and structures required to ensure effective ongoing community 'buy in' at all levels are discussed. Corporate philosophies are addressed. Specific examples from Martha Mine, Waihi New Zealand will be used to illustrate the paper. This will include a brief explanation of previous and current community issues, Newmont Waihi's operations both at Martha Mine and the proposed Favona underground mine, and the practical issues involved in setting up a liaison forum.

Jan 1, 2003

By E. D. Attanasi, J. H. DeYoung

Mineral exploration activity in the US suffered through another depressed year in 1984. And continued strength in precious metals (and possibly industrial minerals) exploration failed to make up for declines in other minerals. 1984 offered little solace for the explorationist. But some new data on mineral exploration provided better statistics for analysts of US mineral exploration trends. The Society of Economic Geologists (SEG) published data from its survey of 1980,1981, and 1982 exploration by US and Canadian companies - 96 companies responded (Barber and Muessig, 1984). In addition, a Mining Engineering (April 1984 p. 345) article by Emerson and Ivosevic presented their data on annual exploration expenditures in the US for gold and for all minerals from 1961 through 1983. A review of 1984 domestic exploration and development activities reported in several industry journals indicates that almost 90% of those projects were directed at gold and silver deposits. Statistics on 1984 exploration expenditures are not available. But some industry observers believe that precious metals accounted for an even larger share of industry's exploration budget in 1984 than in 1983. According to the data of Emerson and Ivosevic (ME, April 1984, p. 349), gold exploration expendi-

Jan 5, 1985

By K Firmin

The Mt Tom Price orebody of Hamersley Iron Pty Limited consists of a folded hematite - shale sequence capped by a layer of goethite. Consequently, variations in iron content occur within the ore body, and as the overall grade is below that required to make specification products, selective mining must be carried out. A necessary preliminary to quality control of products based on selective mining is the production of advance data on the tonnages and grades of material to be expected in future mining areas. Bench plans showing zones of different grades and types of material anticipated are prepared from structural geological information. The grades of materials on a bench are essentially governed by the positions and attitudes of the shale bands. Quality control is exercised by blending different grades and types of material in primary crusher feed. Iron grade is the prime grade consideration although sometimes the level of phosphorus content must be considered. Pre-production grades are determined from assay of samples taken from blast hole cuttings. As shales are more friable than hematite, product fines are always lower in iron grade than the lump product. The realisation of contract specification grade is more difficult with fines than with lump, so maintaining the correct fines grade becomes a prime factor in quality control. Control of fines grade is presently effected by aiming for an appropriate feed grade to the primary stockpile. Studies to estimate fines grade directly by qualitatively taking into account material types are in progress. Quality control measures are checked by monitoring the crushing and screening plant output, and taking appropriate compensatory actions in the mine when required. Minor fluctuations in quality of fines can be blended out on stockpiles. The quality control measures described ensure constant quality products, and a good recovery of high grade material from the deposit.

Jan 1, 1971

In 2007, a total of 278 metal mining operations reported employment to the Mine Safety and Health Administration (MSHA).1 Metal mines were the smallest mining commodity sector, comprising 1.9% of all mining operations. ? Gold mines comprised 44.6% (n=124) of all metal mining operations. Other common types of metal mines were iron ore (n=36; 12.9%) and copper ore (n=35; 12.6%). ? Nevada had the largest number of metal mines (n=45; 16.2%), followed by Alaska (n=28; 10.1%).

Aug 1, 2009

By R. P. King

The MODSIM mineral processing plant simultor is used to find optimal combinations of target separation specific gravities in a typical modem coal washing plant. A plant that is set up with these optimal targets can deliver up to 10% more yield at the same ash content as the same plant set up with separation targets chosen by conventional methods. MODSIM is the only simulator currently available that can simulate the liberation of pyrite and other mineral matter during open- and closed-circuit grinding operations. The simulator can therefore be used to assess the benefits of grinding operations in the flowsheet.

Feb 24, 1997

By Roy F. Waters

An inventory was made by the Bureau of Mines of wastes of mineral origin, water requirements, treatment of wastes, and water treatment practice of 163 industrial installations in the Lower Missouri River Basin. This is the second and concluding report on the survey, conducted in cooperation with the Missouri Basin Field Committee of the Department of the Interior as part of the Missouri Basin project. Principal industries covered by this second report are: Sand and gravel, coal, meat, ice, brewing, paint, petroleum, chemical, fabricated metals, and a number of industries having either no waterborne wastes, or none of mineral origin. Gravel, sand, and silt from 47 producers are the major wastes, totaling 6 million tons annually, Coal mine wastes in the form of slurried solids from washing crude coal are second in volume, totaling 100,000 tons per year. They contain an average of about 40 percent coal. Salt is the third largest waste, amounting to 28,000 tons per year, Next is calcium carbonate, most of which is formed in water treatments, Because of its high unit value, chromic acid is important, although the waste quantity is much smaller; cyanide wastes are also significant because large quantities of sodium hydroxide and chlorine are consumed in their treatments prior to disposal. The various industries discharging wastes use 38 billion gallons of water annually; the recirculation rate is 109 billion gallons per year. The plants discharging no waterborne mineral wastes use 2 billion gallons of water per year and recirculate more than 1 billion gallons. Sand and gravel plants use 13.5 billion gallons; petroleum refineries use 10 billion gallons in direct use and recirculate 82 billion gallons per year.

Jan 1, 1962

By Hubert E. Risser

Although, for about a half-century the percentage of coal production provided through strip mining has steadily increased, recent trends indicate that a peak in percentage (not tonnage) is being approached, principally because of the decline in economic adrantage enjoyed by strip mining compared to underground mining. Factors contributing to the decline are the decrease in the margin of advantage in manpower requirements held by strip mining; an increase in depth and volume of overhurden, requiring larger equipment and capital investment; increasing lack of reserve land blocks large enough to support extensive strip mining operations; more stringent legislation for reclamation of stripped land, with increasingly higher costs of such reclamation; and the increasing costs of land surface rights for strip mining. Already there has been a peak and suhsequent decline in relative importance of strip mining insome major Eastern coal-producing states; trends indicate that a peaking for the whole Eastern region is on the way. Although, in the West the pressures are less severe, they will, nevertheless, reduce to an increasing degree the advantage that strip mining has possessed. For about half a century, strip mining has been providing an ever-increasing share of total coal output in the United States, and in the past 30 years this share has grown from less than 8% to 33.7%, as shown in Fig. 1. Fig. 1 also shows that strip mining is gaining faster in the West than in the East. From 1961 to 1967, output from strip mines grew 63.6 million toqs, or 52.2%. Certainly there is nothing in such performance to indicate any peaking in the level of strip coal-mine production. But the fact is that, if not in actual tonnage, strip mining appears to be reaching its peak in relative importance, at least east of the Mississippi River. And the area east of the Mississippi provides 90.0% of the strip and 94.9% of the total coal production of the nation. The relative economic advantage which spurred strip mining's growth for a third of a century has been diminishing markedly in recent years. Fig. 2 shows evidence of this decline. From 1947 until 1961, strip tonnage output remained fairly stable, at the end of the period showing only a 12.5% decline. Meanwhile, underground coal production fell 44.5%. As the result of the greater decline in underground coal, strip coal in 1961 furnished 30.3% of the total coal produced, compared to only 22.1% in 1947. In the succeeding six years, however, underground coal output increased by 76.5 million tons, while strip output increased only 63.6 million. Further evidence of the strengthening of underground coal's relative position — or if you will, the weakening of strip coal's position — can be found in the major coal stripping states: Illinois, West Kentucky, Ohio, Pennsylvania, Indiana, and West Virginia, which in 1966 provided 80% of the nation's strip coal. Fig. 3 shows what has been happening in three states lying in the Appalachian field and in the total output of these three states. In the figure, the column height represents the output of coal mined by all methods. The number at the base of each column is the percentage mined by stripping. In Pennsylvania and Ohio, the percentage of strip mining increased between 1956 and 1961, but by 1966 had declined from the 1961 level. In West Virginia, a decline occurred during the first five years but was followed by a rise. In January 1968, Coal Age published an article listing the locations and capacities of new large mines in the planning and construction stages that would be operating by 1968-1971. The plans for West Virginia and Pennsylvania indicated all the new mines would be underground. Except to the extent they might replace existing under-

Jan 1, 1970

By Jim Steding

L.G. Barcus and Sons, Inc. recently completed a three-phase project for the expansion of Presbyterian Hospital in Albuquerque, New Mexico for McCarthy Construction Co., the Construction Manager for the project. It was a challenge that allowed Barcus to demonstrate many of it's strengths. Safety of people and property, restricted access, low headroom conditions, extensive planning to maintain hospital operations and a tight schedule were all key elements affecting the successful installation of the Augered Cast-In-Place Piles. Phase I began with installing and performing a 450-ton pile load test on an 18-inch diameter Augerpile 65 ft long. The load test was installed and performed directly in front of the Emergency Room entrance. Space was limited and the E.R. had to remain open with uninterrupted ambulance access. The results of the load test were outstanding. In fact the test pile performed so well that some of the job piles were shortened from 75 ft long to 65 ft long. [ ]

Jan 1, 2003