Search Documents

By P. K. Das, S. K. Singh, C. C. Chang, E. C. Wang, R. B. Roberts

As part of the New York City’s redevelopment of the far west side of mid-town Manhattan, this project will add 1.5 miles of twin bored tunnel to No. 7 Subway Line. The proposed alignment extending from the Times Square Station west beneath 41stStreet turning south under Eleventh Avenue and terminating at 25th Street will include two new stations. The tunnels and station caverns will be primarily constructed in the Manhattan Schist, and will pass in close proximity to several major overly ingstructures. This paper discusses the lithology and structural discontinuities of rockmass along the project alignment, tunnel and cavern rock loading, groundwater hydrology, groundwater quality, groundwater treatment and sustainable design.

Jan 1, 2005

By K. Mallikarjuna Rao

There are several methods available to estimate deflection and ultimate Capacity of laterally loaded piles. In this investigation an attempt has been made to verify the existing methods for prediction of ultimate lateral resistance and deflection with the laboratory and field test results reported in the literature. A 75 pile loading test data obtained from the literature was used to evaluate two methods designed to predict the ultimate lateral resistance of rigid piles and three methods designed to predict the lateral deflections of rigid piles and four methods designed to predict the lateral deflection of flexible piles subjected to lateral loads. The accuracy and precision of each method is quantified statistically. The statistical results of the overall analysis indicate that the mean values of the ratios of predicted to measured lateral capacities vary from 0.62 to 1.14 with an average of 0.88. However, the settlement predictions were much more widely scattered than the ultimate load predictions and in general all the methods have a tendency to under predict the deflections. A new method is proposed by modifying the Broms's method to estimate the lateral deflections of free headed rigid and flexible piles separately. The proposed modified methods were found to be reasonably good in comparison to existing methods and to overestimate deflections.

Jan 1, 1996

By Bill Cain, David F. Tsztoo, R. John Caulfield, D. Scott Kieffer

In 1994, the East Bay Municipal Utility District (EBMUD) commenced a system-wide Seismic Improvement Program to protect their facilities from catastrophic damage. A primary focus of this program has been on retrofitting the 75-year old Claremont Tunnel, which crosses the active Hayward Fault zone. A large earthquake on the Hayward Fault could generate enough right-lateral fault slip to effectively sever this important lifeline. The retrofit project involves construction of a new bypass tunnel through the Hayward Fault zone, together with systematic contact grouting and localized structural repair of the existing concrete liner. Several innovative design measures have been incorporated into the seismic retrofit design, including an oversized tunnel cross section, backfill concrete side drifts, seismic isolation of an internal structural pipe, and shear fuses in the final lining.

Jan 1, 2005

By P. Altounyan

Techniques used to safely control the roof in UK coal mines for some 10 years have been applied to a South African coal mine. This new approach known in the UK as advanced rockbolting technology, is based on applying four fundamental principles: ?Understanding the roof failure mechanisms ?Using an effective roof support system ?Designing this support using measurement ?Monitoring the performance of the system. The paper summarizes the approach in detail and describes how it is being applied by Anglo Coal, giving results obtained to date. Investigations at a number of South African coal mines, including stress measurements at two Anglo Coal mines, have confirmed that the mode of roof failure (lateral shearing due to horizontal stress) is the same as in other coalfields worldwide, and aspects of current world best practice, including the use of advanced technology rockbolting, are therefore relevant in South Africa. The stress measurements indicated a high level of stress field anisotropy and further investigation of stress conditions in South African coal mines is recommended. The most effective bolting system to resist shear failure is one with high bond strength and stiffness. Short encapsulation pull testing of existing South African systems confirmed that they have low bond strength and stiffness. An improved rockbolt system with the required performance, and features allowing rapid installation and installation quality and performance audit, has been developed and is currently under full-scale trial. Design by measurement and routine monitoring procedures including the use of a rotary telltale device are also under trial. It is anticipated that South African coal mines will be able to obtain significant safety and productivity benefits from the application of this technology.

Jan 1, 2001

By R. Dass

Paper written on project work carried out in partial fulfilment of B. Sc Eng (Extractive Metallurgy) degree Screening is an industrial process that splits material at a specific cut size into one fraction of particles larger than the cut size and another fraction of particles smaller than the cut size. Particles are vibrated to increase the probability of them being accurately classified and to move the oversize particles off the screen surface. In conventional screening, the screen mesh vibrates with a single frequency and the particles on the screen are all exposed to this same frequency. The Ultimate Screener (see Figure 1) is a new screen technology that imparts multi-frequency vibrations to the screen mesh so that different parts of the screen surface vibrate at different frequencies. The Ultimate Screener incorporates an additional deck that holds the multi frequency adapters as shown by Figure 2. These special adapters can transform single frequency vibrations into multi frequency vibrations. When the screen motors are switched on they begin to vibrate. This vibration is transmitted to the adapters via the body of the machine. The adapters then modify the vibration to have multiple frequencies, which are transmitted to the screen surface via resonating rings.

Jan 1, 2004

By J. A. Lamonica

The Bureau of Mines conducted an environmental noise survey to determine the noise levels to which underground coal mine employees are exposed, to evaluate noise survey techniques and equipment, and to compare noise exposures using two criteria, Walsh-Healey and CHABA, for determining allowable exposures that were under consideration for the Federal Coal Mine Health and Safety Act of 1969- Time study techniques and Bureau-approved standard sound level meters were employed. The shift exposures of 20 percent of the miners studied were in excess of the safe standards established by both criteria. The shift exposures calculated using the Walsh-Healey criteria were greater than those calculated using the CHABA criteria owing to the intermittent nature of the exposure. Ultimately the CHABA criteria were rejected, and the Walsh-Healey criteria were adopted.

Jan 1, 1971

By A. Nkolele

Paper written on project work carried out in partial fulfilment of B. Tech (Metallurgical Engineering) degree Fine coal of the Goedehoop Colliery is dewatered by centrifuging before being sold. Full-scale plant tests were carried out to reduce residual cake moisture by the addition of surfactants. It is believed that by modifying the interface between the coal surface and the adherent surface water, as well as the water occluded in the cake voids, drainage is improved. Two anionic surfactants at concentrations up to 150 g/t were tested on coal of <0.5 mm size. The results demonstrate that quite high additions of surfactant (80 g/t)were needed to reduce moisture from 20 to about 17?18%. It was observed that when increasing surfactant additions at low levels, within a very narrow concentration range, the retained moisture first increased sharply only to decrease sharply immediately thereafter; this effect points to a critical surfactant concentration. Based on the obtained results, the use of surfactants cannot be recommended at this stage; further investigations under more controlled conditions are required.

Jan 1, 2004

By G I. Lumley

‘Every mine is a pilot’ is an attitude which encourages the mining paradox of optimistic mine plans and equipment under performance; propped up by an environment lacking accountability. The premise that ‘every mine is a pilot’, appears to underlie the development and operating approach to most mines. It is the hypothesis of this paper that many mining companies, development teams and their managers largely ignore what is done elsewhere. Anecdotally, most planners don’t know whether the selected rates are high or low (rates based on theoretical models tend to be high – certainly higher than what most companies can achieve). Mines then consistently operate the equipment at rates well below targets; often more than 20 per cent below. Further to this paradox, mine performance data demonstrates the average mine is currently operating their equipment at levels of output not much more than half the output of those in the top ten per cent. On the whole mines don’t know the potential of their equipment and therefore don’t put appropriate plans in place to do better. After all, when ‘every mine is a pilot’ there is little reason to look to one’s peers for an indication of potential. This paper will outline why every mine is not a pilot and how mines do value some knowledge, but not as much as they should. This paper proposes a two-pronged approach to address this issue in the area of equipment performance. This approach is to:1. engage in better forecasting of equipment rates and better subsequent performance through benchmarking against industry standards2. provide conditions for more accountability.These parameters are linked and proper implementation of them will address the losses which many shareholders and financiers have incurred when investing in companies with unrealistic mining plans.CITATION:Lumley, G I, 2016. Is every mine a pilot? In Proceedings International Mine Management Conference, pp 75-88 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 22, 2016

By H. J. Uananisa, M. J. Papo, C. W. Siyasiya, W. E. Stumpf

"SynopsisThe need to reduce weight while maintaining good mechanical properties in materials used in the automotive industry has over the years seen an increased exploitation of various steels to meet this new demand. In line with this development, the ferritic stainless steel family has seen a wide application in this industry, with the AISI 436 type increasingly being used for automotive trims and mufflers for exhaust systems, as well as a significant part of this steel’s application being for the manufacture of wheel nuts and wheel nut caps in trucks, mainly through the deep drawing process. However, there have been reports of some poor surface roughening of this material during deep drawing, with tearing and/or cracking also reported in some instances. This has been suspected to possibly be associated with some local differences in localized mechanical properties between grains and grain clusters of the rolled and annealed material.In order to investigate the poor surface roughness exhibited by AISI 436 ferritic stainless steel (FSS) during deep-drawing, Lankford values (R-mean and ?r), grain size, and microtextures of various sheet samples from this steel were studied. The chemical composition range for the samples was 0.013–0.017% C, 17–17.4% Cr, 0.9–1% Mo, and 0.4–0.5% Nb. The steels were subjected to various hot and cold rolling processing routes i.e. involving industrial direct rolling (DR) or intermediate annealing rolling (IR), and the drawability and final surface qualities of the steels were compared. It was found that the DR route gave an average R-mean and ?r value of 1.9 and -1.4 respectively, while the IR route yielded an average Rmean and ?r value of 1.6 and 0.52 respectively. The high ?r value for the DR processing route had a substantial adverse effect on the drawability. IR samples exhibited a smoother surface finish on visual inspection, while clear flow lines were visible on the DR samples, despite the fact that DR is the preferred industrial processing route due to the reduced production costs it offers. This observation was also confirmed through SEM examinations. The difference in the surface quality was attributed to microtexture. However, the mechanism responsible for this difference still needs to be identified."

Jan 1, 2015

By Jan E. Nesset, Julie Fournier, Jorge Torrealba, Colin Hardie

"Gas dispersion studies have been used to benchmark and optimize plant flotation performance for more than a decade, although this technology is not as widely in use as it likely should be based on the significant improvements that have been reported. Part of the reason may be a general lack of awareness within the industry of just what these improvements have been. This paper reviews a number of the reported case studies, groups them into categories of improvement, and draws some general conclusions. The paper will be of interest to plant engineers and technology providers seeking new approaches and tools for improving their own and clients’ processes.INTRODUCTIONThe sector of flotation hydrodynamics that is now known as gas dispersion technology, and the corresponding terminology, had its beginnings in the 1980’s and early 1990’s in the laboratories of McGill University where the students of Prof. J.A. Finch and Dr. C. Gomez conducted studies of gas holdup, superficial gas rate and water recovery on laboratory flotation columns (Laplante et al., 1983; Xu et al., 1991;, Banisi and Finch, 1994; Finch et al., 1999; Nesset, 2011). Sensors were developed for gas holdup (eg), gas rate (Jg) and bubble size (Db) distribution (Tavera et al., 1996: Finch et al., 1999; Dahlke et al., 2001; Chen at al., 2001; Hernandez-Aguilar et al, 2002, 2005). The sensor measurements were rapidly adapted for use in mechanical flotation machines in plant environments (Gomez and Finch, 2002; Gomez et al., 2003; Cooper et al, 2004; Torrealba-Vargas et al, 2004; Nesset et al., 2007). Somewhat parallel developments were being conducted by Gorain and colleagues at the University of Queensland’s JKMRC on pilot and industrial flotation machines using the McGill approach but utilizing alternate sensor designs for eg, Jg and Db (Gorain et al., 1997, 1999; Schwarz and Alexander, 2006) to link flotation kinetics to bubble surface area flux (Sb). Early industrial applications were those led by the university teams from McGill (Canada), the JKMRC (Australia) and the University of Santa Maria (Chile) at plants in North and South America, Australia, South Africa, Asia and Europe. Industrial organizations that brought the technology on-board in the early 2000’s included Teck Resources (then Teck Cominco), COREM, Vale (then Inco), Anglo American Platinum. Several of the major flotation cell manufacturers also purchased the McGill bubble viewer technology for their own equipment studies. The sensors have continued to evolve with multiple and continuous measurement of Jg (Torrealba-Vargas and Finch, 2006, Bartolacci et al., 2008), gas holdup by acoustic means (O’Keefe, 2007) and a combined Jg-Db device called the Anglo Bubble Sizer (Harbort and Schwarz, 2010). A review of the gas dispersion technology use and development have been provided by Gomez and Finch (2002), Harbort and Schwarz (2010) and Nesset (2010)."

Jan 1, 2015

By Mary Ann Bennett, Val Nichols, Colleen Proctor

"In 1997 when Royal Oak Mines Inc. went into receivership, the mineral processing technicians (mill operators) who had been working at Giant Mine in Yellowknife, Northwest Territories for most of their career walked out with no credentials to serve as testimony of their knowledge and skills.As a result of new diamond mining activity and the establishment of socio-economic agreements, mining industry representatives approached the Department of Education, Culture and Employment (ECE), Government of the Northwest Territories, in 1999. They requested support and direction to promote training and recognition for mineral processing technicians at BHP’s (BHP Diamonds Inc.) Ekati mine. ECE recommended the development of occupational standards and certification.This paper describes the development process and end products that resulted from this collaborative project between industry, government and education. In addition, industry representatives involved in the project share their views on the development process and the benefits of standards and certification.The conclusion invites industry members to support national occupational standards and certification with their associated benefits: standardized training in the workplace and institutions, proof of competence for hiring, recognition of prior learning, and a nationally and internationally recognized credential.INTRODUCTIONSwiftly changing labour market demands are nothing new in the North. The fur trade and mineral discoveries have brought employment to workers in a feast and famine cycle for decades. In the late 1990s, the Giant, Con, Lupin, Polaris and Nanasivik mines were nearing the end of productive runs. Many experienced workers found that without credentials, they had no proof of their abilities to offer prospective employers."

Jan 1, 2005

By Rambabu Pothina, Rajive Ganguli

The economics of a mineral processing circuit is dependent on the numerous sensors that are critical to optimization and control systems. The sheer volume of sensors results in mines not being able to keep the sensors calibrated. When a sensor goes off calibration, it results in errors which can severely impact plant economics. Normally, these errors are not detected until the error grows and becomes a large (“gross”) error. Undetected errors are not remedied until the next calibration, which on average are a year apart Beamex (2019) [1] across all industries. Classical statistical methods that depend on linear relationships between input and response variables are typically used to find gross errors, but are not effective for highly non-linear and non-stationary operations in mining and mineral processing industries. Calibration of sensors is time-consuming and generally requires physical intervention that results in equipment downtimes causing production losses. Therefore, in situ detection methods are warranted that do not require physical removal of sensors to compare with standard measurements or well-calibrated sensors. Data-mining based techniques and algorithms have high success rate in tackling such problems. This paper presents results from a groundbreaking multi-year big data research project whose goal was to develop data-mining-based original techniques in a multi-sensor environment to identify when sensors start to stray, rather than wait for errors to grow. The carbon stripping (gold) circuit in the Pogo Mine of Alaska was selected for this project. Maintaining strip vessel temperatures at optimum levels is crucial for maximizing gold recoveries at Pogo, and hence the focus was on the temperature sensors of the two strip vessels. An automated algorithm to detect errors in strip vessel temperature sensors was developed that exploited data from multiple sensors in the strip circuit. This algorithm was able to detect with a high success rate when bias errors of magnitude as low as ± 2% were artificially induced into strip vessel temperature data streams. The detection times of about 1 month were much less than the industry average calibration frequency of 1 year. Thus, the algorithm helps detect errors early, without stopping the circuit. The algorithm alarms can serve as triggers when calibrations are done. Experimental methodology along with results, limitations of algorithms, and future research are also presented in this paper.

By Joe Roby

Rolling disc cutters are the business end of hard-rock and mixed-face tunnel boring machines (TBMs). Since their first successful employment on a TBM more than 50 years ago, disc cutter technology has constantly evolved, allowing modern TBMs to excavate very hard and abrasive rock efficiently. Disc cutters have also been employed successfully on earth pressure balance (EPB) and slurry machines, cutting rock under water and ground pressure. The range of materials excavated by machines today is broader, excavation rates are higher and cutter costs are lower than ever before, proving the value of investment in cutter development. Disc cutters are used on a range of tunneling equipment, from pipe jacked slurry micro-TBMs less than 1 m (3.3 ft) in diameter to 15 m (49 ft) in diameter, hard-rock boring TBMs. The geological conditions under which they are employed range from sands and gravels, with several bar of water pressure, to extremely hard, massive rock with UCS up to 420 MPa. Regardless of the type of machine or geology, one thing remains constant: changing worn out cutters is costly. When cutters must be changed in the middle of a tunnel, the contractor incurs the cost of downtime as well as the cost of refurbishing or replacing the cutters. In the case of catastrophic cutter failures, the project can be stopped completely for long periods, and the costs mount up rapidly while tunnel production is at a stand still. Catastrophic cutter failures include the occasion when hard-rock disc cutters are failed in groups (called a ?wipeout? phenomenon) and the operator fails to stop the machine, which results in severe damage to the cutterhead. The cause of this can be either an undetected failed cutter propagating damage to surrounding cutters or operator error in steering. Regardless of the cause, the resulting damage can take days or even weeks to repair. When cutters fail prematurely on EPB or slurry machines in certain geological conditions, it is impossible to evacuate the chamber and, therefore, impossible to get [ ] into the chamber to change the cutters. The solution is frequently an unplanned intervention shaft that must be sunk at great cost. The importance of being able to predict cutter life accurately, and in all geological conditions, cannot be overemphasized. For these reasons, cutters have been developed for specific machine types and sizes, as well as for specific geological operating conditions. Different size cutters are required for different size machines. For example, while 483- and 508-mm (19- and 20-in.) cutters are used on large diameter TBMs, it is impossible to employ cutters so large on a small micro-TBM. Also, the cutter must be designed for the specific geological conditions under which it will be operating. The disc cutter rings required to bore extremely hard rock are the most expensive of cutter rings. However, they provide little advantage in weaker rock formations where less expensive rings will do the job as well. It is important to choose the correct cutter for the machine and the geological conditions in order to get the best balance of cost and risk.

Jan 1, 2009

By A. Sariisik

This study analyses the results of a pilot trial of a newly developed armed-chained stone-cutting machine. The machine was developed in Turkey and trialed at the Kaklik/Kocaba travertine quarries in the Denizli District. An armed-chained cutting machine is an alternative to the diamond wire cutting method more frequently used in the production of natural stone quarry blocks, and increases production efficiency and quality. Since there is no need to collapse the blocks using the armed-chained cutting production process, there is no risk of the block developing cracks. This results in a considerable increase in the efficiency of natural stone block production. The armed-chained cutting machine is easier both to assemble and run when compared to other block cutting methods. This process resulted in the production of a larger number of blocks at a lower cost within the same time frame, particularly in travertine quarries and in all other natural stone quarries. The block efficiency in travertine quarries was calculated as 65?80%using the armed-chained cutting machine, compared with 7?14% using the normal diamond wire cutting method.

Jan 1, 2010

By D. C. Oliver

Paper written on project work carried out in partial fulfilment of B.Sc. (Eng.) (Metallurgy and Materials) degree Corrosion in exhaust systems can occur on both the interior and exterior surfaces. Chloride-containing de-icing salts on the roads in colder countries greatly increases the rate of corrosion on the exterior surfaces. This paper investigates the relative exterior corrosion resistance of three alloys?two ferritic stainless steels( AISI Types 409 and 441) and an aluminized mild steel. The exhaust system is split into two categories?the hot end and the cold end. A test for each of these ends was designed?the standard ASTM G85test was modified to create a simulated driving cycle. The cold end test samples were exposed to ten driving cycles, and the hot end test samples were exposed to five driving cycles. A driving cycle constitutes the car being started from cold, driven until the operating temperatures are reached, and switched off and allowed to cool. Pitting corrosion is the primary corrosion mechanism occurring at the cold end of the exhaust system. The aluminized mild steel was the most resistant alloy in this test, and Type 409 the least. However, once the protective aluminium layer degrades, corrosion will occur rapidly. At the hot end of the exhaust system, spalling of the surface oxide layer is the primary corrosion mechanism occurring. Type 441 was the most resistant in this test, and the aluminized mild steel the least resistant. Potentiodynamic tests were performed on the alloys?the results agreed with the results obtained in the exposure tests.

Jan 1, 2003

By Zhang Chuanfu

Keywords: modified coprecipitation method, Ni-Co alloy powders, solid-solution oxalate, growth mechanism Homogeneous solid-solution oxalates of Ni2+ and Co2+ ions were synthesized by modified coprecipitation method and the composition and morphology of the fibrous solid-solution oxalates precursor were characterized by XRD, IR, DTA/TG and SEM analysis. The effects of feeding methods, pH values, precipitation temperature, reactant concentration, addition surfactant, alcohol washing and drying process on the morphology and dispersion of the precursor were investigated in detail. The experimental results showed that the coprecipitated powders have characteristics that are different from those of the mechanical mixtures with the same stoichiometry. Based on the observations of precursors growth and SEM morphology of the precursor, the oriented attachment was proposed for the well-aligned growth of the fibrous Ni-Co alloy precursor particles.

Jan 1, 2005

The results of precious metal exploration carried out by Amoco Minerals New Zealand Limited over EL 33-137 in the Longwood Range, Southland, are described. Widespread gold and platinum in alluvial deposits on the perimeter of the range and anomalous gold in stream sediments on its southern and south western flanks indicates that the precious metals were probably derived from erosion of the mafic rocks of the Longwood Complex.

Jan 1, 1983

By N. A. C. Smith

The Bureau of Mines motor gasoline surveys have been conducted in January and July, during 1920 and 1921. The Bureau has obtained and analyzed samples of gasoline representative of that marketed in the larger cities. These surveys have indicated that the gasoline on the market during the winter months is more volatile than that sold during the summer months. Naturally, the motorist desires a more volatile gasoline in the cold winter months, as it affords greater ease in starting. The fourth semi-annual motor gasoline survey, conducted during the month of July, shows an interesting relation between the market price and the quality of motor gasoline. This is particularly evident if figures obtained today are compared with those of a year ago. At the time the Bureau of Mines conducted its summer survey of motor gasoline last year, the average tank wagon price of gasoline was 28.2 cents per gallon. This year it was 21.2 cents, a drop of practically 25%.

Jan 1, 1921

By W Skinner, C G. Kelsey, J R. Kelly

The iron ore industry has reached the end of an unprecedented period of expansion triggered by China’s demand for iron ore. Lower ore prices have led producers to focus on optimising mining operations while extracting the maximum tonnage from the infrastructure presently in place or from projects already underway. A rising global surplus is expected to further force ore prices down and lead to output curtailments, which in turn will help to restore market balance. However, investment in the development of new resources and the development of new infrastructure will inevitably become necessary. Making the right decisions in relation to future processing infrastructure in a climate of uncertain demand and price volatility will not be as straightforward as in the past, where expanding the scale of a proposed operation has been the answer to ensuring economic viability. Overall cost and environmental pressures particularly in relation to wet processing will dominate the decision-making process. IMP Technologies (IMPTEC) has anticipated the need for a dry low cost processing alternative, which can open the way for the development of lower grade magnetite deposits and ensure the sustainability of processing in Australia. The lower grade magnetite deposits are generally fine grained and require grinding to p80 of 30 to 40 microns. Historically, the cost of grinding to these sizes has been and remains a key factor determining the economic viability of a magnetite processing operation. The IMPTEC Super-fine Crusher and Cyclomag Separator are the key components of a proposed radically simplified dry processing alternative, which addresses both cost and environmental issues. This paper reports on the results of pilot super-fine crushing and cyclomag separation test work, focused on supporting the feasibility of the proposed dry processing route for the production of high-grade pellet plant feed from fine grained low-grade magnetic ores.CITATION:Kelsey, C G, Kelly, J R and Skinner, W, 2017. Dry processing of magnetic iron ores – addressing cost and environmental issues, in Proceedings Iron Ore 2017, pp 215–220 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By J. D. T. Capocchi, M. B. Mourao

The rate of reaction between iron oxides and carbonaceous materials, agglomerated as pellets, was studied experimentally by measuring the weight loss as a function of time. The effects of temperature, carbon type, inert gas flow rate, pellet size and additions (sodium. carbonate and Portland cement) were determined. It was shown that the value of the apparent activation energy can display large deviations under different experimental conditions; in the present work it was found to be 226.6 kJ/mol. The reaction with coke is slower than with charcoal, and the rate increases as the flow of inert gas in the reaction vessel decreases. Comparison of the rates for pellets of different sizes has shown that for small pellets the initial rate is faster but that it slows down at high conversions owing to the penetration of inert gas into the pellet. Additions of sodium carbonate and Portland cement increase the rate; sodium. carbonate promotes the catalysis of the Boudouard reaction, which is the slowest of the partial reactions. The increase in the rate with Portland cement is attributed to the release of water vapour

Jun 18, 1905