Search Documents

By S. D. Viljoen

The use of ceramics to protect equipment subjected to wear in abrasive and corrosive applications has been accepted by most plants as the industry norm. Little is, however, known about alternative special ceramic based products which are available for the protection of plant assets. With careful engineering, impact resistant ceramics can be used in high impact zones using modern ceramic technology. Properly selected and properly installed, ceramics will provide a tough wear resistant lining for protection against abrasion and impact. Basalt, on the other hand, is widely used in coal washing plant process pipes with varying degrees of success. Basalt is normally not used for the lining of bends, ?T? pieces or reducers due to the reduced wear resistance compared to alumina ceramic. The advantage is a much reduced initial capital cost. A patented ceramic composite non-return valve solved an old problem encountered in the operation of medium sumps. The design approach overcomes the lack of functionality of alternative designs and reduces valve wear while preventing medium settlement during plant shutdown periods. Direct bonded ceramic pulley lagging is becoming the industry norm, eliminating most of the problems encountered with conventional pulley lagging systems.

Jan 1, 2010

By G. Huang, S. Vytla

Computational fluid dynamics (CFD) is a continually developing numerical technique by which complex fluid flow problems can be solved on computers. To be able to transfer CFD expertise to analyze and design a face-ventilation system, a comprehensive validation study of current CFD tools against mining-related benchmark experiments is required. In the last four years, such studies, funded by National In¬stitute for Occupational Safety and Health (NIOSH) under Grant #R01 CCR415822, were conducted in the Department of Mining Engineering at the University of Kentucky. A wide array of ventilation schemes and mining configurations were considered. Recently, an additional study was performed in cooperation with the NIOSH Pittsburgh Research Laboratory. This study was dedicated to the methane behavior in the empty (containing no equipment) face area with a blowing curtain and a 10. 7-m (35-ft) setback. In this paper, the authors present and discuss the computer-simulation data and compare them with data collected during the laboratory studies at the NIOSH lab.

By Keith A. Heasley

The LaModel program has been used successfully in the United States for many years to design pillars to ensure global stability of pillar recovery operations. However, the recent Crandall Canyon Mine collapse showed that further research was required to improve the design of pillar recovery under deep cover. Toward this end, a new calibration procedure was implemented in LaModel. This calibration procedure prescribes techniques for calibrating the critical LaModel input parameters based on empirical abutment loading and pillar strength, as utilized in the time-tested ALPS and ARMPS programs. The calibration procedure is intended to help guide a novice modeler in choosing calibrated input parameters that produce a standard model that fits within the verification database. However, the rigid parameter specification incorporated in the calibration procedure also removes most of the flexibility in LaModel for specific calibration to the unique conditions at a given mine site. In this paper, a number of the LaModel input parameters are varied outside the bounds of the suggested calibration and the effects on the model results are analyzed. Ultimately, it is shown how the LaModel user might vary certain input parameters to adjust the model to site-specific conditions, while still maintaining the general accuracy and philosophy of the recommended calibration.

Jan 1, 2012

ABSTRACTOperations Research and associated techniques have wide application in the Mining Industry and have been used in Mount Isa since 1961.Typical of the projects undertaken by the OperatIons Research staff are1. the development of a complex computer programme for use in economic evaluation of mineral deposits,2. development of a production scheduling and control system for a complex mining operation,3. SImulatIon of a metallurgical plant operation to test the adequacy of design specifications and4. analysis of vehicular accident data to valuate alternative courses of insurance action.

Jan 1, 1968

By John Heilig, Patrick Andrieux

"Near-field monitoring of blast induced seismic vibrations is a practical and useful way of assessing blast field behaviour for diagnosis and optimization purposes. It is also necessary in order to provide the information from which empirical vibration prediction equations, such as the one proposed by Holmberg (11 for example, can be derived. (Strictly speaking, the “near field” extends from the blasthole itself to about one charge length away from it; however, throughout this article, “near field”will.most often refer to the outer limit of this zone, from roughly 0.75 to 1.50 charge length away.) In order to obtain reliable data, proper field monitoring techniques are of paramount importance. Once the data are properly recorded, analysis can be done either in the time domain (describing vibration amplitude vs. time) or in the frequency domain (usually describing vibration amplitude vs. frequency)."

Jan 1, 1995

The ore, as sent to the sulphide mill, is a mixture, in varying proportions, of oxidized ore from above the 450-ft. level and sulphide ore from above and below (to date mainly from above) that level. The oxidized ore consists essentially of quartz, with varying amounts of kaolin and clayey material which passes into the slime and, in excess, creates a serious problem in settling. Pyrite may be present in small amounts. The gold is free and extremely fine.The ore, classed as sulphide, consists of pyritic material in a quartz gangue. The sulphides have been exposed to weathering, leaching by descending solutions and attack by ascending gases and actual burning. The alteration products occur in widely varying proportions and this variation adds to the difficulties in settling and control of grinding and flotation.Copper Minerals.-Chalcopyrite is the principal copperbearing mineral with smaller and varying amounts of covellite, which is sometimes associated with chalcocite, both these minerals being apparently of secondary origin.Examination of tailing by Dr. Stillwell has revealed all stages between clean chalcopyrite, chalcopyrite tinged with covellite, covellite with residual cores of chalcopyrite and clean covellite.The chalcopyrite is free floating, very few particles of clean chalcopyrite being observed in the tailing from granular flotation. The chief tailing loss is probably as chalcopyrite occurring as small inclusions in pyrite...

Jan 1, 1939

By Peter J. Nicholson

Since the reintroduction of soil mixing to the United States over 10 years ago, the work installed by soil mixing technology has grown dramatically. From an annual turnover of less than ten million dollars per year the volume of soil mixing put in place has grown to an estimated $40 million per year in the year 2000. The majority of work done to date has involved walls, either for excavation support, permanent retaining structures or hydraulic cut-off walls. The other major use for soil mixing has been for mass stabilization of soils whether for isolation of contaminants or for retaining structures. This paper will discuss the uses of and costs of typical soil mix structures. BACKGROUND Soil mixing is defined as the in-situ combining of reagents, typically cement, with native soils, the purpose being to modify or improve the ground. This history of soil mixing covers only the use of cement slurry, aggregated with soil in-situ by mechanical mixing methods only. Soil mixing by use of high-pressure hydraulic means, also known as Jet Grouting, will not be discussed. In addition this will not cover ex-situ (above ground) mixing, or mixing dry reagents with soil. Only mixing applications for building, civil and heavy construction applications will be discussed, with only passing reference made to uses of soil mixing for environmental remediation work.

Jan 1, 2001

The Hyde-Macraes Shear Zone (HMSZ) is low angle, duplex thrust system that has developed in a graphitic pelite schist within the Otago schist belt, New Zealand . At Round Hill lateral ramps have developed parallel to the movement direction between+ the footwall and hangingwall shears. These structures exhibit normal oblique-slip displacement which has been an important mechanism for creating space in an otherwise compressional system. Gold-bearing quartz veins were emplaced along the boundary shears and lateral ramps during thrusting. Gold within the lateral ramps is coarse (up to 300 microns) however hanging wall cataclasite development in the boundary shears after the gold was deposited has reduced the grainzise of most of the gold to less than one micron. This bimodal gold distribution has metallurgical implications with respect to the maximisation of gold recovery at Macraes.

Jan 1, 1993

The refractory nature of residual gold in Kalgoorlie calcines is caused by occlusion in dense pyrrhotite formed by fusion within pyrite grains during decomposition. Fusion of pyrite increases as the rate of heating exceeds the rate of sulphur expulsion. By controlling these rates in relation to each other in a fluidised system fusion is limited and an expanded structure is formed. The increased area presented to cyanide solution, and the decreased diffusion distance, makes gold more accessible for extraction. Gold extraction from expanded pyrrhotite, before oxidation for porosity, is comparable with extraction from fully oxidised calcines from Edwards roasters. A method is suggested for standardised comparison of cyanidation residues.

Jan 1, 1957

This paper provides an update to a paper by the author on an overseas explorer's perception of New Zealand, presented at the 1997 New Zealand Minerals & Mining Conference. New Zealand has one of the most open and internationally competitive economies in the world. The petroleum exploration industry in New Zealand is booming with a record number of wells planned for 2000. New Zealand is keen to encourage investment in mineral exploration to develop its natural resources. A study of the geological potential of New Zealand estimated the value of known and potential resources of metals at $86 billion. Gold has the greatest potential, with a total resource estimated at $33.5 billion. The price of gold has averaged NZ$554 since the beginning of 1998, and NZ$593 in the last year, which is very competitive with other countries. An assessment of country risk compared New Zealand with twenty other countries in ten risk categories: sovereign risk, land access, environmental issues, land claims, mining legislation, social risk, infrastructure, civil unrest, natural disasters and workforce. New Zealand ranked fifth, showing it has low country risk. This provides a high degree of certainty for investment, which is important for the perception of New Zealand as an exploration destination. Corruption was considered separately, and New Zealand ranked third out of ninety countries, showing it is one of the least corrupt countries in the world. New Zealand has a favourable business environment, good geological potential, low country risk and no corruption. Despite this, New Zealand has not registered on the radar screens of overseas mineral explorers, and the positive factors appear to have been overlooked. New Zealand has considerable undeveloped mineral potential, and with the current rise in commodity prices, it is hoped New Zealand can participate in a resurgence in mineral exploration.

Jan 1, 2000

By J. A. Stewart

"A common problem in the mining industry involves the overloading of established conveyor systems. This overloading can have a number of causes, such as new production technology or a changing market condition which increases demand. An overloaded system usually spells disaster and leads to clean-up problems, equipment failures and lost production. The Cape Breton Development Corporation's Lingan Mine had a serious overloading situation on its underground coal clearance system, and equipment was being damaged and production was being lost. It was rectified, in part, by increasing the coal clearance capacity through the use of booster conveyors. This paper discusses the problems which led to this situation, the booster concept and the installation of the first unit at the Lingan Mine.IntroductionThe Lingan Mine is a submarine coal mining operation with an annual production of 1.5 million tonnes from three advancing longwalls. Coal is conveyed 3400m up a 13% slope to the surface. Designed and installed in the early 1970s, the system's 820-tonne/hour design initially proved adequate; however, by the late 1970sthe system was handling surge loads of 1640 tonnes per hour due to the introduction of new face equipment.The coal clearance system consisted of three 485-Kw, two 210-Kw and one 105-Kw conveyors. Each conveyor was designed for 820 tonnes per hour using 1050-mm, Type 10 belt with a 35-degree troughing profile.There were many effects of the overloading on the system:• Loading beyond the physical capacity of the belt resulted in spillage along the conveyor, which increased operational and maintenance costs.• Overloading of the drive components resulted in premature equipment failures.• Spillage at the drive pulley often resulted in damage to the belt and pulley lagging and, under extreme conditions, the conveyor would require partial unloading before it would operate. This was a particular problem under wet conditions because the 485-Kw conveyor drives were fitted with single-drive drums."

Jan 1, 1982

By Kentaro Kuraji

INTRODUCTION Background Tokyo, the capital of Japan, is one of the largest cities of the world. As many as 33 million people live in Tokyo and three neighboring prefectures although the city occupies only 0.6% of the area of the country. The network of Metropolitan Expressways serves as a major artery for daily physical distribution in Tokyo. The Central Circular Route of the Metropolitan Expressway (MECCR) is located innermost among the three circular routes in Tokyo (Figure 1). Once completed, MECCR is expected to drastically mitigate traffic congestion in the central Tokyo area and provide drivers wider varieties of options in route selection. Alleviating congestion is estimated to reduce 400,000 tons of carbon dioxide emissions annually. The eastern and northern sections and part of the western section of MECCR have been completed with the total length reaching 33 km. The western section will be extended southward by approximately 4 km in the spring of 2010. An 11-km-long western section of MECCR that is currently being constructed is composed mostly of tunnels. A large number of power supply, gas supply, telephone, drinking water and sewerage pipes have been placed under the Yamatedori avenue along which MECCR is being constructed. The shield tunneling method has therefore been adopted for constructing tunnels along the route. The method involves the advancement of a shield tunnel boring machine (TBM) through the ground simultaneously assembling segmental rings within the shield. The method not only enables the building of highway tunnels more quickly and efficiently than other methods but also minimizes the effects of construction work on the surrounding area and the environment. Constructing the tunnel using the conventional cut-and-cover method might have required large amounts of time and cost because relocating the numerous objects buried under the Yamatedori avenue might have been necessary during tunnel construction. It was also considered desirable to place the tunnel at a depth of 30 m or more from surface to prevent tunnel construction from adversely affecting railways because the tunnel was expected to cross eleven railways and subways. This is one of the reasons for selecting shield tunneling as an effective method. The shield tunneling method was finally adopted for a length of 7 km in the 11-km western section of MECCR. The shield tunneling method was also employed in the Ohashi Tunnel located southernmost in the 11-km western section of MECCR. This paper describes the construction of the Ohashi Shield Tunnel.

By Philip Bonanno

The first major project in Boston's new access to Logan Airport was an Immersed Tube Tunnel which extended 3,600 ft. from South Boston to East Boston across Boston Harbor. Twelve tube sections, 300 ft. long x 80 ft. wide x 40 ft. high, were lowered into an excavated trench which was then backfilled. The depth of the trench at mid-channel was approximately 100 ft. below mean high tide. At the East Boston end the tube terminated close to the present shoreline. At the South Boston end the tube terminated approximately 600 ft. inland from the shore line where a ventilation building was required. The depth to subgrade from existing ground at the ventilation structure was approximately 85 ft. The soil profile at this location consisted of 50 ft. of miscellaneous rubble fill, 25 ft. of Boston blue clay, and 10 ft. of glacial till. A small amount of weathered argellite existed at the north end of the structure. Part of the Morrison Knudsen, Interbeton, J.F. White, Joint Venture contract to construct the Immersed Tube Tunnel (ITT) was the construction of a cofferdam at the tube/ventilation building interface. The ventilation building was to be built as part of another contract. The construction of the cofferdam and the excavation to the building subgrade was the responsibility of J.F. White Contracting Company.

Jan 1, 1994

By Laura McNally

In 2006, McNally International Inc., in a joint venture partner-ship with Aecon Constructors, was the successful bidder on two York Region Tunnel Projects: the Bathurst Collector/Langstaff Trunk Sewers and the York Durham Sewer System (YDSS) Interceptor Sewer 19th Avenue, both in the Toronto area. These projects comprised a total of 13 km (8 miles) of 2.74 m (9 ft) finished diameter tunnels and are both part of the YDSS. Both contracts required the use of earth pressure balance (EPB) tunnel boring machines (TBM) with a precast concrete segmental liner.

Jan 1, 2008

By Christopher Mark

Severe dynamic multiple seam interactions can occur when active mine workings are subsided by underlying mining activity. The most dramatic events are usually caused by longwall mining or pillar recovery beneath open, overlying entries. But pillars in abandoned workings can also fail and cause subsidence and damage an overlying mine. This paper describes a case history in which an apparent ?pillar squeeze? in the abandoned workings of a lower seam was initiated during retreat mining in an upper seam. The event subsequently extended more than 1,500 ft and ultimately closed the upper seam mine. Analysis indicated that the pillars in the lower mine were adequately sized for the lower seam mining and were not affected by the initial development above them. When retreat mining in the upper seam had progressed several hundred feet, however, the pillars located directly beneath the pillar line were overloaded, and an extensive squeeze initiated in the underlying workings. The squeeze, in turn, subsided the overlying workings, causing widespread rib falls and roof instability. Previous examples of dynamic multiple seam interactions resulting from delayed subsidence of underlying workings have been reported in the literature. This is, apparently, the first recorded incident in which pillar recovery in an active mine triggered pillar failure in an underlying mine, which then triggered a dynamic interaction that impacted the active overlying seam.

Jan 1, 2012

By Steve Meador

West Virginia's basic coal mining regulatory programs are not unique when compared to Federally approved programs implemented by other coal producing states. In fact, the language in The West Virginia Energy Act governing subsidence mirrors that written in the Federal Surface Mining Control and Reclamation Act as well as other states' statutes. Certain legal and administrative issues, how¬ever, combine to make West Virginia's regulation of surface subsidence a singular approach.

Jan 1, 1986

By P Papanastasiou, J Hadjigeorgiou, E Kyriakou

The south west area of Cyprus has a long history of slope instability problems. The location and extent of these landslides has been influenced by ground morphology, geological structure and the presence of weak rocks and cohesive soils. The main triggering mechanisms have been precipitation and/or seismic events. Landslides have contributed to the decision to relocate villages and considerable efforts have been put into maintaining the integrity of the local transportation network. This paper uses a recent case study of road embankment failure near Pentalia in southwest Cyprus to review the available tools for the analysis of slope instability. It further demonstrates how the shear strength reduction technique can be used in a finite element analysis to better visualise the slope instability mechanism of a road embankment and provide a reliable tool in selecting appropriate remedial measures.

Jan 1, 2006

By Gaulton R

The Commission maintains a data base first computerised in 1957 and containing information from over 18 000 boreholes located mainly in the Latrobe Valley area. Some of the borehole derived information dates from the turn of the century, although most of it has been collected as a result of Commission investigations conducted over the past 40 years. The Resource Data Base contains not only information gained directly from the drilling itself but includes the results of chemical and physical testing on many hundreds of thousands of samples retrieved from boreholes. Replacement value of the Resource Data Base has been estimated to be around $200 million, and it's integrity and accessibility is clearly of paramount importance, not only to existing mining and power generating functions but to the future evaluation and use of the vast brown coal Resource.

Jan 1, 1992

At last year's. annual meeting of The Institute, Sir George Fisher, as President, compared it somewhat nostalgically with a meeting of its kind in the 1920s when comment was expressed on the decline of Australianmining and on the lack of new mineral discoveries.I feel that tonight's annual meeting is even more an occasion for nostalgia, for it represents the seventy-fifth anniversary of the founding of The Australasian Institute of Mining and Metallurgy. I hope, therefore, that I may be allowed to retrace some of the circumstances of this Institute's origin and at the same time to look at some of the broader happenings of those 75 years.From this distance in time it is, of course, much easier to get things in perspective and one of the things that compels enormous admiration in looking back over the history of our Institute is to note the qualities of foresight and keen concern for professional standards which moved the pioneers in this Institute. They had no benefit of hindsight to aid them.Just over 75 years ago, a small group of men met in Broken Hill to discus.s the possibilities of forming an association of mining engineers. The moving spirit was Uriah Dudley, our first secretary, manager of the Umberumberka mine at Silverton. The first formal move to form an association of mining engineers came from the Amalgamated Mining Managers Association of Australasia. At the time, this association was a fairly new group, being 5 years old.It had been formed to try to raise the standard of management throughout the industry. Uriah Dudley and our first provisional president, John Howell, held their first talks in 1891 and further meetings at Broken Hill followed. The inaugural meeting, attended by 200 members, was held in Adelaide in April, 1893.

Jan 1, 1968

The 1981 Review: In the late 1970s there was an upsurge of interest in the prospecting and mining of this countryÆs mineral resources. That upsurge of interest was accompanied by a mounting public concern over the damage mining operations might do to the environment. Concern was also expressed about what some people perceived as inadequacies in the legislation which regulates mining and the grant of mining privileges, and inconsistencies in the relationship of that legislation to other legislation regulating land use and the use of resources.

Jan 1, 1984