Search Documents

By I. M. Ahmed, R. S. Hassan, M. I. Aly

Extraction and separation of La, Sm and Dy ions from acidic sulfate-phosphate solutions was investigated using a cation exchange extractant, bis(2,4,4-trimethylpentyl) phosphinic acid, CYANEX 272, in kerosene. The influence of shaking time, equilibrium pH, extractant, sulfate and phosphate ion concentrations, diluent type and temperature was studied. The extraction was found to be pH-dependent, and increasing the phosphate ion concentration inhibited the extraction which was found to be endothermic. The stoichiometry of the extracted metal species was found to be MOH.H2OHSO4H2A.A2. Aliphatic diluents were found to enhance the extraction compared to aromatic diluents. The results showed that there was a separation mode between the metal ions when varying the hydrogen ion and sulfate ion concentrations, under the used experimental conditions. The investigated process was used for the recovery of La, Sm and Dy from the acid solution resulting from the leaching of low-grade monazite.

By T Leidich, M Van Zyl, H Lacy

Mining ‘as usual’, until the most recent decades has resulted in limited landform planning and a general lack of mine waste landform design. Material characterisation, mine planning and dedicated professionals undertaking these tasks were rarely available or in place at the majority of mines. This has led to landform instability, erosion, sediment and poor quality water emanating from mine landforms. In many cases rehabilitation and reclamation failed and these sites have ‘landform features’ that are difficult to relinquish or leave and have little or no apparent land use. In many cases mined landscapes around the world have resulted in a less functional and degraded environment, with deleterious impacts on surrounding ecosystems.This situation is now slowly being addressed, as global companies, academics and practitioners and their organisations have started to exploit the ideas from an integration of earth sciences and mining through the application of planning software dedicated to the design of landforms.This development has had its genesis primarily in the United States. We suggest that process has been driven, in recent decades, by the application of resources in response to the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA), (USA Congress 11 December 1980) and other mine reclamation legislation enacted by federal and states regulators in the USA. The combining impact has seen a huge transfer of capital back from the public purse and ‘potentially responsible parties’, into abandoned mines to affect control, remediation, and reclamation/rehabilitation of those mines.Given this investment in rehabilitation and reclamation, people engaging in the business of landform planning have had the opportunity to address landform reclamation of historic and active sites. The skills of engineers and scientists with improved technology, waste rock characterisation and modelling tools have been combined resulting in the evolution of landform design and in mine planning of active mines. This has delivered cost-effective, sustainable mine closure designs for over 30 years. Integration of mine design with an understanding of geomorphic principals and the natural landscape, coupled with waste and soil characterisation, yield a positive result. Recently work has been applied across large and small-scale projects by companies. As these processes develop, ideas and concepts are evolving that active mines, or mines in the early planning stages, could use to help reduce double handling, and in the long run reduce overall project and closure costs, more effectively attain the desired final land use, and enhance the industry’s reputation and licence to operate.CITATION:Leidich, T,?Lacy, H?and Van?Zyl,?M,?2014. Application of design concepts and engineering controls necessary to deliver well-designed and rehabilitated landforms, in Proceedings Life-of-Mine 2014 , pp 55–66 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By S. Zhao, S. P. He, M. Y. Zhu, Y. Tao

"The effect of two refining slags (A: 1.0–1.8 CaO/Al2O3 ratio, 11–20 wt% SiO2; and B: 1.0–1.2 CaO/SiO2 ratio, 25–35 wt% Al2O3) on the inclusion morphology of a carbon structural steel (Q235B) was studied by controlling the balance between the steel and the refining slag at 1600ºC in a Si–Mo resistance laboratory furnace. The results showed that most of the inclusions in the molten steel balanced with slag A were formed by a lowmelting CaO–MgO–Al2O3–SiO2 system with a total oxygen content (T[O]) being fixed at 6–13 ppm. The inclusions in liquid steel balanced with the slag B were mostly formed by the CaO–MnO–Al2O3–SiO2 system, with T[O] controlled to 19–26 ppm. The overall size of the inclusions under balance conditions was higher in the steel reacted with the slag B than that reacted with slag A, with the latter showing more inclusions smaller than 3 um. In order to generate a large number of spherical CaO–MgO–Al2O3–SiO2 inclusions smaller than 3 ??m while decreasing the T[O] in the resulting steel, the composition of slag A should be used. This composition allowed improving the cleanliness of the slab, and is also advantageous for the castability of the molten steel. IntroductionThe sample used in this study was a typical carbon steel manufactured by CQ Steel. The galvanized, tinned, and plastic composite steel plates made of the original plates are used extensively for decorative panels, general dust pipes, drums, instrument cases, switchboxes, and train cars, among other uses. The target control composition is shown in Table I. The S and P contents are usually fixed during production below 0.020 and 0.025 wt%, respectively, with the aim of reducing longitudinal cracks on the slab surface."

Jan 1, 2017

New Millennium Capital Corp. shall not be liable or responsible for any claim or damage, direct or indirect, special or consequential, incurred by the user arising out of the interpretation, reliance upon or other use of the information. Users should not rely on information for any purpose other than for gaining general knowledge of New Millennium Capital Corp. Although New Millennium Capital Corp. believes that its expectations reflected in these forward-looking statements are reasonable, such statements involve risks and uncertainties and no assurance can be given that actual results will be consistent with these forward-looking statements.

May 1, 2011

A special meeting of the Institute, at which the Institute of Metals Division will join with those members who are most interested in iron and steel, and in coal and coke, will be held in Milwaukee, Wis., October 8 to 11, 1918. The technical program is as follows: INSTITUTE OF METALS DIVISION Tuesday morning, October 8: The Metallography of Tungsten, by My Jeffries. (Bulletin No. 138, p. 1037.) The Constitution of the Tin Bronzes, by S. L. Hoyt. Paper, title not given, by C. H. Mathewson. Notes on Babbitt and Babbitted Bearings, by Jesse L. Jones. (Bulletin. No. 140, p. 1397.) Oxygen and Sulphur in the Melting of Copper Cathodes, by S. Skowronski. (Bulletin No. 135, p. 645.) The Relation of Sulphur to the Overpoling of Copper, by S. Skowronski. (Bulletin No. 135, p. 651); with discussion by Philip L. Gill. (Bulletin. No. 140, p. 1156.)

Jan 9, 1918

By E. P. Youngman

The Siamese mining lew, which is cited as "The Sian Mining Act, 2461 (1919)," was enacted February 14, B. E. 2461 (A. D. 1919), corresponding to the ninth year of His Majesty's reign. This act replaces the Sian Mining Act of 1901 and repeals all edicts, decrees, laws, rules, and local customs relating to mining the terms of which are inconsistent with the new law. It shall in- clude all subsequent alterations or additions, as well as all rules issued by the Minister (of Land and Agriculture) already in force or to be brought into force publication in the Government Gazette to be deemed sufficient notice of any modifications or alterations. (Art. 1, 2, 5, 83, and 85.) Legislation passed recently amending certain provisions of the mining law for the purpose of controlling the sale of minerals is the mining amendment act, B. E. 2474, given August 21, 1931 (7th year of the present reign), which repeals provisions of the mining act, B. 3. 2461, and also all rules and regula- tions relating to mining that are inconsistent with the amending ect. Under article 25 of the mining amendment act, B. E. 2474, ministeriel regulations (of the Minister of Agriculture) were issued August 21, 1931. Further recent legislation, brought about by the agreement of the Siamese Government to become a party to the international tin restriction scheme (inter- national tin pool), is the tin and tin ore restriction act (Siam), B. E. 2474, which came into force on September 1, 1921, its purpose being to suspend the

Mar 1, 1933

"RÉSUMÉOn discute les principales sources de dilution au cours d’une exploitation souterraine. Les différentes définitions de la dilution en usage sont analysées. Une nouvelle méthodologie de calcul simplifiée et facile à utiliser dans la pratique minière est présentée. Cette méthodologie permet de remplacer les différentes expressions analytiques en usage par les deux facteurs de dilution seulement : un «facteur de dilution planifiée» lié à la sélectivité d’abattage au niveau de la planification minière et un «facteur de dilution additionnelle » permettant de juger de l’efficacité du contrôle de terrain et de la dilution pendant l’exploitation souterraine. L’application de cette méthodologie donnerait un outil nécessaire aux niveaux de la planification, du suivi des travaux d’exploitation et d’éventuelles études comparatives des coûts entre les différentes situations minières.ABSTRACTThe principal sources of dilution during underground evaluation and mining are discussed, then definitions of ore dilution currently in use are analyzed. These definitions vary depending on the authors. A new ore dilution evaluation methodology is proposed, replacing the ten different analytical expressions by only two: the planned dilution factor related to the stoping selectivity, done at the mine planning level, and the additional dilution factor related to the efficiency of the dilution control measures during stoping operations. The conclusion shows that the use of this methodology would be a definitive asset in planning, in stoping operations follow-up, and in future costs comparison studies between mining operations."

Jan 1, 2001

By L. H. Gevantman

A program for the compilation of evaluated physical and chemical numerical properties data is being pursued at the National Bureau of Standards within the Office of Standard Reference Data. This program is being sponsored by the Department of Energy and managed by the Battelle Office of Nuclear Waste Isolation in Columbus, Ohio. The intent is to assemble a reliable body of numerical properties data concerning candidate mineralogical materials in which high-level radioactive wastes are to be buried. The ready accessibility of the data to site designers and the credibility achieved through the evaluative process are designed to help assess and compare the feasibility of each candidate material for use as a disposal site. Both generic and site-specific data are to be assembled. To date, generic rock salt properties have been assembled and published by the NBS as NBS Monograph 167. Details of the effort to produce this book are discussed.

Jan 1, 1982

During the past 20 years, FKC-Lake Shore, located in southern Indiana, has been working with Contitech, the German conveyor company, to push vertical conveyor technology to new depths and open up additional opportunities for underground mine owners. Historically, the underground mining industry has largely been unable to realize the benefits of these efficient systems due to the design limitations in maximum depth and capacity. Until recently, only relatively shallow depth mines with low production rates have been a ?t for a vertical conveyor system. This, however, is changing with technical advancements in the Pocketlift system. With each milestone, a new vertical conveyor record is set for depth and capacity. For instance, in 2002, FKC-Lake Shore set one such record with the installation of a Pocketlift system at a mine in the Illinois coal basin with a lift height of 273 m (896 ft) and a production rate of 1.8 kt/h (2,000 stph). Although it was unthinkable at that time, today?s vertical conveyors are capable of reaching lift heights up to 700 m (2,300 ft) with an average production rate of 450 t/h (500 stph). These new lift heights and production rates are opening the technology to more potential mine owners and shifting the way people look at moving material in the future.

By A. Simon, J. Weyer, J. Brune, V. Zhiteneva

"Reiche Zeche is a lead-zinc-silver deposit in Freiberg, Germany, that was mined for over 800 years. Since 1969, Reiche Zeche has been a teaching and research mine with numerous adits for dewatering large amounts of inflowing water. Infrequent metal water quality monitoring in the 1980-1990s and flooding of the mine in 2002 led to a lack of relevant data. New measurements were taken at different level adits and ore veins for comparison to historical values, revealing pH levels as low as 1.95, conductivity as high as 22000 µS/cm, and an overall trend towards less acidic waters. INTRODUCTION Reiche Zeche is part of the Himmelfahrt Fundgrube, a former iron ore mine in Freiberg, Germany, in the Erzgebirge mining region of Saxony. The polymetallic sulfide ore found in Freiberg was mined from 1168 to 1969, and though it is no longer producing ore, Reiche Zeche remains as a teaching and research mine for the Technische Universität Bergakademie Freiberg. The most important ore minerals mined were sphalerite, galena, pyrite, chalcopyrite, and silver, and important gangue minerals include calcite, fluorite, barite, siderite, and quartz (Zänker et al 2002). Over one thousand ore loads were mined from this region during operation, which was ceased in 1969 after the lower part of the 700 meter depth was flooded, leaving only the top 200 meters under the surface open for research and teaching. Mined materials from this region can be separated into high grade ore and waste rock. High grade ore, composed of pyrite, sphalerite, galena, chalcopyrite, and arsenopyrite, was brought to surface for smelting during mine operation, and spaces were backfilled with waste rock, which is the primary site of sulfide oxidation and acid mine drainage (Haubrich and Tichomirowa 2002). The waste rock includes remnants of ore from ore loss, veins which were too small to mine, or ore minerals within host rock. Waste rock is primarily composed of biotite gneiss, with sulfides including jarosite, gypsum, minor anglesite, scorodite, and sulfur (Haubrich and Tichomirowa 2002). When weathered, the gneiss forms clay minerals such as illite and kaolinite (Haubrich and Tichomirowa 2002)."

Jan 1, 2016

By James M. Link

A program was initiated tinder sponsorship of the U. S. Bureau of Mines to investigate pipeline behavior of raw and spent oil shale slurries. Slurries were recirculated in pipeline loops with 150-mm and 200-mm diameter horizontal test sections and a 150 -mm diameter vertical test section. Slurry concentrations from 10 to 60 weight percent were investigated. Critical and deposition velocities were observed. Head losses were measured at various velocities. Rheology measurements were made on representative homogeneous samples from the pipeline. From these data, pipeline energy requirements were predicted by computer and compared to pipeline data. Computer programs were also used to analyze pipeline data for two flow models: 1. Heterogeneous flow regime for coarse, settling slurries 2. Homogeneous flow regime for nonsettling suspensions The economics of slurry transport of raw and spent shale were examined. Cost estimates encompassed a range of pipe diameters to transport a wide range of throughputs of both raw and spent shale. Similar estimates were made for conveyor belt systems to provide a valid cost comparison. Economic comparisons are valid in a general sense, but a specific study must be made to determine the cost advantages of hydraulic transport for a given mine.

Jan 1, 1977

By Walter English

THE four papers making up this symposum have been prepared espe-cially for those who have no knowledge of seismograph prospecting. To many people mathematics is a formidable subject, and many are discouraged from studying seismograph prospecting under the mistaken assumption that the mathematical requirements are severe. In the papers presented here there is not a single mathematical equation. We believe that considerable competence in dealing with some of the most important problems of this work can be attained without any mathe-matical training whatever. At the present time, there is a real need for interpretation of results by persons thoroughly competent to bring geologic experience and imagination to bear on data that are subject to multiple interpretation from a strictly physical viewpoint. Likewise, those charged with the responsibility of planning seismo-graph exploration campaigns would do well to become familiar with as much as possible of the technical aspects of the work. They would then be in better position to judge of its success in individual cases. It has often been said that the seismograph is a new structure-finding tool for the geologists to use. Using a tool and using its product are two different things. One does not use an automatic screw-threading machine when he buys a box of screws at the hardware store. Neither does the geologist

Jan 1, 1939

By C. Y. Sun

China is a country with abundant resources of tungsten, taking one of the world?s top-positions regarding both the total reserve and the amount of industrial production. China?s tungsten resources occur mostly in multi-metallic deposits rather than in single-metallic deposits. China?s multi-metallic tungsten ores have the characteristics of coexistence with other valuable components such as molybdenum, bismuth, copper, sulfur and fluorite. These ores are usually low in grade and difficult to process. The technological challenge in mineral processing lies in separation of multi-metallic components in these complex ores and a comprehensive utilization of natural resource. Several cases of industrial practice of processing China?s typical multi-metallic tungsten ores are presented.

Jan 1, 2014

By F. T. Cawood, M. N. M. Cudjoe

The ability to conduct real-time material tracking in mines has been a long-standing challenge. Technological innovations such as radio frequency identification technology (RFID) have over the years contributed to the effective tracking of material flow and reporting of metal content. This paper outlines the laboratory procedures and results from testing the suitability of microdot technology as a viable technique for real-time material tracking in mining. The paper clarifies the reasons for conducting the test and presents the material safety data sheet (MSDS) from a South African and Canadian perspective. Microdots from three aerosol systems were immersed in water, heated to 100°C, and crushed into coarse and fine material. These tests were used to ascertain if the technology could withstand mining conditions. A strength, weakness, opportunity, and threat (SWOT) analysis was used to evaluate and compare microdot technology with RFID. It was shown that microdot technology has some potential to track ore parcels because data integrity was retained after exposure to post-blast mining conditions. However, more improvement is required to digitally detect microdots before the technology can be implemented at scale in the mining industry.

Apr 2, 2022

By J Player, R de Vries, J F. Carswell, R Hassell

"The feasibility of Dugald River mine was highly sensitive to mining and geotechnical design assumptions, particularly stope dilution and strike length. Following the start of initial mine development in 2012 the project was suspended in 2013 due to concerns over the complex ground conditions and resulting dilution, stope sizes and general mineability. A technical risk mitigation program was undertaken with a key aim to increase the level of confidence in predicting stope dilution.A stope sizing and dilution model was developed that provided a range of stope sizes based on geotechnical conditions and acceptable dilution. The original feasibility used a standard stope size of 25 m height by 25 m span. The new model was used as the foundation for the subsequent updated development plan for Dugald River that reduced much of the previous technical risk through greater confidence in the geotechnical and mining parameters.Several methods to predict stope hanging wall dilution and appropriate stope size have been used at Dugald River that relied on the modified stability graph method. Improvements to the method were identified as more rock mass and mining data became available through the completion of a trial stoping program, increased underground development and a large geotechnical core logging campaign. These improvements not only focused on the technical aspects of the model, but also on creating an easy to use and sustainable process that could be used at multiple stages of mine planning from life-of-mine (LOM) through to final stope design.Several of the main improvements are: understanding stope failure mechanisms and collecting only geological information that is most relevant detailed modelling restricted to the rock mass that could be expected to influence stope behaviour accounting for different stope failure mechanisms with the stability chart method assigning a geotechnical confidence factor to the data making it useful as a mine planning tool with integration into the mine planning process using performance of completed stopes to update and calibrate the model.The model provides recommended hydraulic radius and associated dilution estimates across the ore body. Providing the hydraulic radius allows planning engineers the option to consider single, double and triple lift stoping options suitable to mine scheduling. While the model has been calibrated for conditions at Dugald River the process used to create the model is not site specific and is applicable to other steeply dipping tabular orebodies.CITATION:Hassell, R, de Vries, R, Player, J and Carswell, J F, 2017. Improving the prediction of stope hanging wall dilution – a critical factor to the success of Dugald River, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 71–78 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 16, 2017

By Claus Becker

The new, 2.600 m long pipe under the river Elbe in Hamburg/Germany required for 2 traffic lanes, emergency lane and space for utilities a boring diameter of 14,20 m(46,6 ft). According the geology (glacial deposits consisting of clay, sand and marl, all containing big boulders) a Slurry-Shield with crusher was selected. With a minimum cover of 7 m and a maximum pressure of 5,6 bar extensive ground treatment was necessary to make the drive feasible. The machine contains a lot of new developments. The drive was finished in spring 2000 so all experiences can be reported. A special risk sharing contract avoided completely litigation.

Jan 1, 2001

By John Parianos, Simon Richards

SUMMARY The Clarion Clipperton Zone (CCZ) hosts the most valuable deposit of polymetallic nodules yet discovered. Understanding the geology of this deposit is key to its effective exploration and mining. Nautilus Minerals (via its subsidiary Tonga Offshore Mining Limited; TOML) has been progressing its understanding of the relationship between seafloor morphology/structure and nodule abundance/morphology, both locally (within its contract areas), and globally (across the CCZ and the span of its contract areas of almost 70% of the CCZ). We present the first results of a project with the aim of developing a method to quickly and accurately map seafloor morphology/structure (Tectonic Subcomponent scale) without the necessity for high resolution seafloor multibeam data. Furthermore, the results presented here will allow a first attempt in understanding the relationship between seafloor geomorphologically-defined zones and plate-scale tectonics of the CCZ and adjacent plate segments. INTRODUCTION A relationship between the type of geochemical active layer and nodule abundance/morphology has long been understood (ISA, 2010). Consideration of the range of differing nodule types found within, but especially between, the TOML contract areas allowed Parianos and Pomee (2017) to refine this relationship further via interpreted thickness and dynamism of the geochemically active layer. The scale of the deposit, both in terms of space and time is staggering (a 10-20 cm thick deposit, spanning almost 4500 km, varying within a circa 10 Ma period), but a segment wide geological map may one day prove to reflect controls on nodule formation and distribution.

Jan 1, 2018

By Thomas T., Read

THE decades immediately before and after the end of the nineteenth century (1890-1910) were a period of increased activity in mineral industry education. One reason for ,this, undoubtedly, was the rapid increase in mineral production in the decade 1880-1890; pig iron and copper production tripled; coal, lead, and zinc output more than doubled. Most of the other mineral substances followed the same general trend. Aluminum production began in 1886; petroleum output, which in 1888 was less than it was in 1882, almost doubled in the next three years. Gold alone showed no appreciable change until its discovery at Cripple Creek in 1891, followed by the Klondike in 1896, brought to boiling a public interest in minerals that had been simmering for some years previously. The first cyanide plant in the United States was erected at Bodie in 1893, and the first chlorination plant at Cripple Creek* the next year. Silver- lead smelting had already greatly developed, and the metallurgy of copper was almost transformed. The hearth area and smelting capacity of copper reverberatory furnaces more than quadrupled between 1878 and 1894; matte converters were first erected at Butte in 1884. Copper production of the United States in 1899 was 30 times that of 1872. While it was the increased technology used in mineral production that really made the field attractive for educated young men, undoubtedly they did not realize that, and were impressed mainly by the quantitative increase in output. Another factor was the increased general interest in engineering education; three times as many men took engineering degrees in the United States in 1890 as in 1880; 1893 showed almost a 56 per cent increase over 1890. Industry had come to recognize that technical training was worth while. The mineral industry lagged somewhat at first; the total number of mining degrees

Jan 1, 1941

By Nelson SOUTO, Nicolas LEGRAND, Sami ABDELKHALEK, Zafer KOONT

A work roll thermal crown model has been developed for a wide range of hot and cold rolling mill applications. The model is extremely fast, robust and accurate to determine the evolution of thermal crown all along the rolling campaigns. It has also ability to consider work roll shifting, multiple segmented cooling zones along the length and circumference of the roll as well as composite rolls properties (e.g. different thermal properties between mandrel and core of the roll). Moreover, the model includes simultaneously fast and slow temperature evolution calculations, respectively near roll surface (skin area) and at a certain distance below the roll surface (bulk area). This gives to thermal crown predictions a higher accuracy than conventional thermal crown models from literature that consider only the slow temperature evolution regime. An optimization procedure together with roll surface temperature and roll thermal profile measurements have been used to tune the model. The tuned model applied to hot rolling conditions has shown a significant influence of roll shifting and composite rolls properties on the prediction of roll temperature distribution and thermal crown during rolling. The tuned model applied to cold rolling conditions highlights the importance of mill operators practices to modify cooling distribution across roll barrel length with the segmented cooling zones to adjust the thermal crown and to get better strip shape control.

Oct 1, 2019

By S. M. H. Ahmadi, K. Barani, F. Moradpouri, R. Ghaedrahmati

As exploration is time-consuming, costly, and risky, determination of the erosion surface of a metalliferous deposit before geophysical surveying and exploration drilling might be very helpful. Geochemical haloes can be used to determine whether the erosion surface is supra-ore or sub-ore and thus reduce the risk of exploration operations. The aim of this investigation is to determine the erosion surface of the North ROK porphyry deposit (NRPD) in northwestern British Columbia in Canada using linear productivity (LP), which is the content of an element defining the halo multiplied by the width of the halo. A total of 2045 soil samples from the B horizon were analysed using ICP-MS for 36 elements, including Cu, Mo, Pb, Zn, Au, As, Ag, Ni, Co, Fe, and Mn. The data-set was snalysed to obtain the statistical parameters and the elements Cu, Mo, Pb, and Zn were chosen to calculate the linear productivity and the total linear productivity. These four elements were modelled using probability plots to identify and separate subpopulations in terms of anomalous haloes and background, including the threshold values of each subpopulation. The results of the probability plot modelling and thresholds values were then used to map the distribution of each element in a GIS to calculate the linear productivity. The total linear productivity indicated that the erosion surface is supra-ore. Finally, a 3D orebody model of the Cu, Mo, Pb, and Zn distributions was constructed using borehole data and used to validate the results.

Feb 6, 2023