Search Documents

By Neel Gupta, Brijes Mishra

Coal mining activity disturbs the natural equilibrium of in situ stress state such that the induced stresses deform the surrounding rock mass. Although the installation of roof supports typically prevents rock deformation, rock mass failure may still occur in bolted roof. The erratic failure of rock mass after few days to months and years of excavation is the result of time-dependent deformation of roof rock under constant surrounding stresses. In the current research, the triaxial laboratory creep experiments proved that Marcellus shale exhibits time-dependent deformation under constant stress that was smaller than the failure strength. However, unlike conventional experimental results, the time-dependent deformation did not depend on the level of constant stress. The often-neglected initial state of specimens and intrinsic heterogeneity highly influenced the time-dependent failure of Marcellus shale.

Jul 27, 2021

By R. B. Crookston

Oil shales differ from coals in that they contain less carbonaceous material, convertible to volatile hydrocarbons, and more inorganic rock. In all pre-commercial oil shale development, involving extensive full scale mining operations, there have been no explosions. However, large scale mine tests with oil shale dusts by the Bureau of fines showed that propagating explosions could be induced under certain circumstances. Laboratory tests were conducted on a broad spectrum of oil shale dusts to define chemical properties and to seek correlations with subsequently determined fire and explosivity properties. These latter properties, indicative of safety hazards, increased as the Fischer assay oil yield of the dusts increased and as particle size decreased. Laboratory data were used to relate fire and explosivity properties of oil shales to those of coals and other carbonaceous materials and to assist in the identification and evaluation of potential hazardous situations which may be encountered in oil shale mining and processing.

Jan 1, 1978

By Reed. Donald F.

"Deposits of gray hematite occur in two districts in Talladega County, Ala., the Emauhee-Tallasochatchee and Weewoka, both in the vicinity of Winterboro, 50 miles east of Birmingham.The deposits were investigated by the Bureau of Mines in 1943 and 1944. Approximately 13,000 feet of diamond drilling was done and 6,000 linear feet of trenches excavated and sampled.A total of 13,000,000 tons of ore averaging 36 percent iron was indicated in all areas.A detailed discussion of each property investigated, drill logs, and sampling results are given in this report.In the work done in the Talladega County iron investigation, special acknowledgement is due to Paul M. Tyler, formerly regional engineer, Eastern Region, and Richard W. Smith, formerly district engineer, for aid and direction of the project; also to J. B. Clemmor, metallurgist, for diligent research work in the Southern Experiment station laboratory. All were members of the Bureau of Mines Staff.The project was conducted in cooperation with the Federal Geological Survey, whose field work was in charge of T.G. Andrews assisted by Brewster Baldwin. The able and valuable assistance of Andrews and Baldwin aided greatly in accomplishing the project.The areas investigated by the Bureau of Mines were in two districts: The Emauhee-Tallaseehatchee district, between Sylacauga and Sycamoer (marked B on fig. 1) and the Weeworka district, between Winterboro and Sycamore (marked A on fig. 1)."

Mar 1, 1949

By Moris Fresko, Julia Sun, Charles C. Golembewski, Vytas Svalbonas

"A history of mill strain gaging at Metso is presented. The output of these strain-gaging programs is compared with calculated stress ranges from different finite element solutions. These comparisons expose the amount of approximation that exists in the analytical solutions, starting from geometry, and material properties, and ending with different forms of internal load models. The influence of strain gaging results on mill design and analysis practices is also discussed. While these instrumentation programs are valuable in identifying areas of high stress in mills, and locations of stress concentration factors, they are by no means extensive or comprehensive enough to verify general internal load models. The vast majority of the programs were aimed at getting additional data about potential failure points, rather than describing overall mill stress behavior. This is especially true since the more recent gaging programs have not included the difficult task of gaging the mill rotating structure interior. This paper tries to avoid the novice path of leaping to general conclusions on the basis of insufficient data."

Jan 1, 2014

By Sidi Deng, Sharon Pedraza, Aaron Noble, Subodh Das, Bin Ji, Wencai Zhang, Michael Van Brunt

In this study, a MSWI bottom ash sample was assessed to evaluate the feasibility of various physical beneficiation processes in concentrating valuable elements prior to chemical leaching. The raw sample was initially assayed to determine the content and economic value of various metals present in the material. The potential recoverable value (PRV) of the sample was calculated, and the result showed that the total PRV of the sample was 483 $/ton, with Ti, Sc, Fe, Cu, and Zn being the most valuable metals. Next, various physical separation processes, including size fractionation, froth flotation, magnetic separation, and gravity separation, were conducted to determine the extent to which the valuable elements can be concentrated. The results were compiled into an element-by-beneficiation enrichment ratio (er) matrix that was used to develop suitable beneficiation flowsheets for further consideration. The result clearly show delineation of four products, including a Fe-rich product that can be isolated by magnetic separation (er = 5.0), a Cu/Zn-rich product that can be isolated by flotation (er = 5.3 to 9.4), a Sc-rich product that can be isolated by gravity separation (er = 0.6), and a Ti–rich product that is produced in the residue. Lastly, the leachability of valuable elements from the bottom ash sample was determined by acid leaching tests. The results indicated that it is viable to employ hydrometallurgical methods to recover and purify the valuable metals. This work provides a reference for the recovery of valuable metals from MSWI bottom ash from both the technical and economic aspects.

Apr 27, 2024

A compilation of papers presented at The Second WVU Conference on Coal Mine E1ectrotechnology in Morgantown, West Virginia on June 12 -14, 1974. Papers cover areas of electric power, electronic communications, detection and location of trapped miners, and electronic sensors and monitoring systems.

Jan 1, 1974

By Hernán Parra, Samir Campomanes, Lily Ponce, María Suárez

En este trabajo se analizan algunas posibilidades de tratamiento de la atacamita con el objeto de posibilitar la extracción del cobre que contiene, así como la del oro que muchas veces acompaña a estos minerales. Se ha probado el esquema lixiviación ácida de cobre seguido de cianuración, así como la flotación y segregación. Los resultados indican que existe una gran posibilidad de tratarlos con éxito mediante métodos de segregación.

Sep 20, 2019

By D. E. Sullivan

The Minerals Availability Program of the Bureau of Mines conducts cost evaluations of current and potential mineral operations in the United States and foreign countries. The International Mining Cost Indexation System (IMCI) allows data of different time periods within a country to be updated to a common base year for analytical purposes. The IMCI comprises 12 factor cost indexes and an exchange rate series for 96 market economy countries, denominated in both local and U.S. currency. The IMCI for each country contains 12 time series indexes that measure the average annual rate of change in the cost of factor inputs to the mining industry within that country. Mining industry factor cost indexes include wages, plant and equipment, construction and mining materials, power and transportation, and other measures considered to comprise the majority of capital and operating costs. Cost data or proxies are collected in local currency. Index series within each country are constructed separately and indexed on a 1975 base year. The local currency index is converted to a U.S.-dollar-based currency index using an exchange ratio.

Jan 1, 1987

By Mike O'Shea

Industrial minerals are extremely important to downstream industries and in our everyday lives. Their ontribution to the UK economy and to society as a whole is greatly underestimated. The industrial minerals sector is lacing increased pressures - environmental and competitive - both at home and abroad. These pressures are likely to increase. The Government, working in conjunction with the industry, can help the industry to meet these challenges. The role of Government is to establish a dialogue w ith the industry, to find out what its concerns are.and to ensure that these are taken into account in the draw ing up of policies that affect it. There is also a role for it in exploring, with industry, the linkages between environmental improvement and competitive advantage, and giving, w herever possible, early warning about regulatory developments. In order to maximise the effectiveness of links, industry needs to be coherently organised and represented both in the UK and in the European Union (EU).

Jan 12, 1997

By B. W. Gandrud

[The Bureau of Mines is conducting an extensive investigation of coal preparation in the Alabama coal fields in cooperation with the University of Alabama and coal-mine operators. In this investigation the drainage characteristics of typical coals from the Warrior and Cahaba n fields were studied. Tire main purposes of this study has been to evaluate no nearly as possible relative influences of certain factors on rate of drainage and to determine whether the drainage characteristics of coals from different beds or from different mines on the soma bed differ materially. A further objective was the development of a laboratory drainage test that would predict approximately the rate at which any coal will drain after having been loaded into a railroad car in a saturated condition. The study has been confined to samples of slack coals - that is, coals from which none of the fine sizes have been removed. The samples ranged in upper size limits from 7/16 inch to 3 inches. It did not seem necessary to study nut and egg sizes, that is, sizes from which the fine coal has been removed by screening, as these lose water so rapidly by natural drainage that they present no serious problem in dewatering after treatment in a washer. The significance of drainage characteristics of Alabama coals is apparent in view of the fact that not less than 70 percent of Alabama?s total coal product is subjected to wet washing before being materials.]

Jan 1, 1941

Wildcat strikes in the Appalachian coal fields, primarily in West Virginia, have resulted in an estimated 4.5 million ton loss in coal production during July and through the first week in August. Since then, the strike intensified further, and on August 9, nearly all of West Virginia's 60,000 miners were off the job with another 10,000 miners on strike in eastern Kentucky. The Bureau of Mines estimates that West Virginia's coal output is currently (8/9) eight million tons below last year when the state produced 108 million tons. West Virginia, the Nation's second largest coal producer of coal behind Kentucky, has not failed to mine over 100 million tons a year since 1938. At the end of the second week in August, nearly all coal miners in West Virginia remained out. The strike is a protest against a cutback in union health and retirement benefits. An announcement June 23 about the United Mine Worker's health and retirement fund precipitated the strike, Fund directors said that because of inflation and production losses caused by earlier wildcat strikes and the severe winter, miners would have to pay the first $250 of hospital costs and 40 percent of doctor bills, up to $500 a year. Previously, the funds paid all hospital and doctor bills. According to the West Virginia Coal Association each day of the strike in West Virginia results in a loss of coal production of 500,000 tons, a loss of $3.8 million in miners wages and $1 million in contributions to the UMWA's health and retirement fund.

Jan 1, 1977

By W. H. Carrington, A. C. Richardson

"INTRODUCTION The Powhatan mine of the Franklin Coal Mining Co. is located in the western part of Jefferson County, Ala., on the Louisville and Nashville Railroad, 40 miles west of Birmingham. The Mary Lee bed at this point yields coal with fair coking qualities, but with an ash content as mined so high as to prohibit its use in the production of metallurgical coke. At present the entire output of the mine is washed in single-compartment jigs and marketed as locomotive and domestic fuel.Figure 1 gives a typical seam section of the Mary Lee bed at the Powhatan mine. This section shows that the bed is divided by rock partings into three benches. In many parts of the mine, particularly in the older workings the roof rock is so weak that it can not be held without excessive timbering. This condition has restricted the operation in many parts of the mins to the middle and bottom benches of coal. The 6 inches of draw rock between the top and middle benches is very strong and makes an excellent roof requiring only a normal amount of timbering to support it. In the newer workings of the mine the character of the rock above the top bench is strong and it is believed that in the future it will be possible to work all three benches. This study was undertaken for the purpose of determining the washing characteristics of the Mary Lee bed at Powhatan and the effect on these characteris-tics of including or omitting the coal from the top bench. It was also the purpose of the study to show whether it would be possible to produce a washed product sufficiently low in ash to be used for the manufacture of metallurgical coke. This paper is one of a series of reports on the washability of Alabama coals which is being prepared by the U. S. Bureau of Mines and tin University of Alabama. With the cooperation of the coal producers of Alabama. It contains the results of screen sizing and float-and-sink tests of representative samples of run-of-mine coal, and the results of table tests on the minus 3/16-inch sizes of the raw coal."

Apr 1, 1933

By Ronald D. Rothchild

This report describes the results of a study of longwall ignition hazards and specific suppression systems to minimize each of the major hazards. The major ignition hazards were identified by conducting a literature search and conversing with knowledgeable individuals in the United States mining industry. Three classes of potential ignition suppression systems are discussed: triggered suppression systems for face ignition, passive suppression systems, and control of ignition hazard in the gob. The triggered suppression systems included protection for the shearer, head and tail gates, welding equipment, and the shearer power cable. Passive systems include improved ventilation and water sprays, and charges in the shearer head. Gob protection can be improved by isolating the gob from working areas and by introducting inerting agents into the gob.

Jan 1, 1976

By Tahereh Rostami, Behnam Khoshandam

In the present paper, the recovery of mixed spent cathodes is evaluated and performed through a hydrogen reduction process. Firstly, the lithium is isolated by the hydrogen reduction process as LiOH at 600 ◦C for 15 min with 10% H2 with a flow rate of 350 ml/min. In the second step, 98.37% Li is recovered through water-leaching of hydrogen reduction products at 100 ◦C for 90 min with 50 ml/g. The filtration residual is reduced by using a carbothermic reduction process and a hydrogen reduction method. The first one is performed under an Ar atmosphere at 900 ◦C for 210 min and the second one is conducted at 800 ◦C for 150 min. The purer products are achieved using the hydrogen reduction method at lower temperatures and shorter holding times compared to a carbothermic reduction process with recovery percentages of 100%, 99.06%, and 70% for Ni, Co, and Mn, respectively. Given the importance of reducing the emission of toxic gases, the hydrogen reduction process is also a promising method for metal recycling. The obtained results also demonstrated that Li, Co, Ni, and Mn can be effectively separated from the mixed cathode material through the hydrogen reduction process as a sustainable and environmentally friendly recycling process. This study provides an impressive understanding of the hydrogen reduction process and valuable guidance for a larger-scale hydrogen reduction process.

May 3, 2024

By S. N. Kalyakin, D. S. Flett, M. A. Mulagaleeva, N. V. Gudkova, S. S. Serdyuk, V. I. Kuzmin, Institute of Chemistry and Chemical Technology SB RAS, O. A. Logutenko, V. N. Kuzmina, V. G. Lomayev

"The Chuktukon niobium-rare earth elements ore deposit is located in Siberia (Russia). Weathered carbonatite crusts are the basis of the ore deposit. The deposit itself is 3.5 km in length, about 800 to 1400 m in width and up to 200–300 m in thickness. The ores are composed of iron-manganese oxides (hydrogoethite, hematite, psilomelane, pyrolusite) and contain 3–7% of rare-earth phosphates (florencite, monazite) and 0.5–1% of niobium oxide (pyrochlore). The ore is completely finely dispersed and consists of oxide particles formed of compact, dense aggregates which makes ore dressing as well as leaching of the rare and radioactive elements very difficult. Several options for processing of these ores have been considered: 1) reduction of the iron oxides to magnetite followed by beneficiation with magnetic separation to produce a rare metal concentrate; 2) processing of the rare earth elements (REE) containing minerals by direct alkaline-acid treatment; 3) processing of the ores using nitric acid leaching in an autoclave.INTRODUCTIONThe Chuktukon niobium-rare earth metal ore deposit is located in Siberia, in the Krasnoyarsk region, 110 km from the Boguchan hydroelectric power station which has recently been commissioned. This mineral raw materials is capable of providing impetus for the modernization of the Russian rare metal industry because of its qualitative and quantitative characteristics. The deposit is located in a region of promising industrial development and is a part of the territoriy where the Russian Federation’s Program “Complex Development of the Lower Angara Region” is currenly being realized. The main program directions are creation and development of industrial activities in sectors such as power, metallurgy, oil and gas, gold, rare-metals, and timber. The program will aid the development of the niobium and rare-metal resources of the Lower Angara and neighbouring regions as well as increase the national production of REE and therefore import substitution (Lapin, 1997; Lomaev & Kuzmin, 2003; Lomaev & Serdyuk, 2011; Serdyuk, Lomaev, & Kontorovich, 2000)."

Jan 1, 2016

By B. van Beek, J. H. Zietsman, A. Lexmond, N. J. Andrew

"In platinum group metals (PGMs) smelting, the slag-to-matte ratios are very high (approximately 4:1 to 9:1). The slag temperature therefore has a strong influence on matte temperature, which is a continual concern due to the low matte melting temperature and its resultant high superheat. Maintaining a stable slag temperature is therefore a critical safety and operational issue. This project aims to improve the understanding of the slag bath temperature drivers so that a more effective slag bath temperature control strategy can be implemented.With the aim of developing a multiphysics model of the furnace, extensive data analysis was performed to develop an in-depth understanding of the process before the start of modelling work. In this work, the effect of fluctuating furnace feed composition on slag temperature was examined. The results are based on equilibrium calculations using FactSage, implemented with ChemApp.A method was developed, using an equilibrium calculation at 25°C, to convert the available chemical assays to approximate mineralogical assays in order to determine the feed enthalpies. Actual 2013 furnace feed data was used and the average specific energy requirement to produce slag and matte at 1600°C was calculated to be 671 kWh/t concentrate. The furnace energy input was then kept constant, and it was found that the slag temperature varies significantly as a function of the feed composition. These results were compared to actual slag temperatures measured on site. It was found that close management of the furnace energy balance is important for maintaining a stable slag temperature."

Jan 1, 2014

The Elura Orebody consists of a number of parallel, vertically oriented pipe-like structures of pyrite-sphalerite-galena mineralization located at the core of a structural dome. Concentric zoning of the mineralization into an outer Siliceous, intermediate Pyritic and inner Pyrrhotitic Zone has been previously recognized and is used in routine geologic modelling of the lead, zinc and silver grades.Statistical analysis of the metal grade distribution in the orebody has confirmed the importance of the mineralogical zones in the understanding of grade trends. The gradational nature of intra-zone boundaries, especially those related to the subjective definition of the Siliceous Zone, are apparent in the statistics.

Jan 1, 1990

By H. J. Snyder

Both the room-temperature and 600°F (315°C) primary solid-solution phase boundaries for the silver comer of the Ag-Cd-In temary system have been determined using X-ray diffraction and metallo-graphic techniques. Solid solubility of indium in silver at room temperature and 600°F (315°C) is shown to be between 20.3 and 21.7 wt pct, and corrects the previously extrapolated value of 18 wt pct appearing in the literature. The solid solubility of cadmium in silver at room temperature, not previously established, is shown to be between 34.9 and 41.3 wt pct. The solid solubility of cadmium in silver at 600°F (315°C) is confirmed as 43.2 wt pct. The shape of the primary phase boundary line for the subject temary system appears straight at room temperature and curves con-vexly towards the solvent (silver) comer at 600°F (315°C). THIS investigation was undertaken to initiate development of the Ag-Cd-In ternary diagram by establishing the primary solid-solution phase boundary in the silver corner of the diagram. At the present time, a diagram for this ternary system is not available, while this system appears to offer potential for a variety of uses. One alloy in the system has already proven to be useful as a control rod material in nuclear reactors.1"3 To encourage additional exploration of the potential of the system an understanding of its ternary diagram would be beneficial. It is towards this end that the present study is directed. LITERATURE SURVEY In undertaking this study, a comprehensive literature survey was first conducted to find information that would be useful for guidance. Useful knowledge did result from investigating the respective solubilities of indium and cadmium in silver as indicated in the binary constitutional diagrams of the systems Ag-In and Ag-Cd and also reviewing possible shapes of ternary primary phase boundaries. Weibke and Eggers~ used metallographic techniques to establish the system In-Ag as illustrated in Fig. Is This diagram shows that silver in the solid state is capable of dissolving approximately 18 wt pct In. This solid solubility of indium in silver holds true from room temperature up to 1276°F (691°C), then decreases continuously up to 1'761°F (960.5"C), the melting point of the silver. The solid-solubility limit of indium in silver established by Weibke and Eggers has been confirmed by Hume-Rothery and Reyno1ds. G Durrant' used a method which consisted of microscopic examination of quenched specimens to establish the Cd-Ag system as displayed in Fig. 2.' The primary phase boundary of Fig. 2 proved to be in good agreement (ie., within 1 wt pct) with other studies*'1' of the Ag-Cd system made using X-rays and metallog-

Jan 1, 1968

By Augusto Díaz Rodríguez

Como parte de la campaña de seguridad y prevención de accidentes producidos en las minas de San Antonio de Esquilache, el autor del presente texto expone una serie de medidas que permitan reducir el índice de siniestros producidos durante las labores tales como: golpes con herramientas, carroneo, explosivos, lesiones, caídas de piedras por chimeneas, de trozo y minerales en los buzones, etc. Para ello, resalta la creación de organizaciones dedicadas a prevenir dichos incidentes, así como la aplicación de un programa de seguridad que incluya el uso de cinturones de seguridad, acuñado de los techos y galerías mediante barretillas, limpieza de caminos y carretillas, supervisión contínua de los caminos de las minas, equipo de seguridad del trabajador, et. Por último, la permanente charla de capacitación del personal de seguridad, como la cooperación de los trabajadores durante este proceso, disminuye la cantidad de 4o accidentes mensuales a 2 desarrollados en los últimos meses en la mina.

Jul 20, 1955

By B. W. Gandrud

[The Bureau of Mines is conducting an extensive investigation of coal preparation in the Alabama coal fields in cooperation with the University of Alabama coal-mine operators. In this investigation the drainage characteristics of typical coals from the Warrior and Cahaba fields were studied]

Jan 1, 1941