Search Documents

By Susumu Okabe

Top blow injection has been applied to continuous copper smelting and converting by Mitsubishi Materials Corporation since 1974. In this process, injected feeds are captured by and dispersed in the molten bath immediately and effectively, and the reaction is enhanced by the agitation of the bath. The continuous motion of the molten bath, however, may cause severe damage of furnace lining materials, if the injection is not controlled and the furnace is not designed properly. In order to suppress refractory wear, especially at the bath line, surface wave of the molten bath should be moderated. A cold model study was carried out with water bath in a cylindrical vessel and the physical model was derived which correlates the oscillation of gas jet impingement on the bath surface and the surface wave. It was found that a half of the proper frequency of the gas jet impingement coincides the proper frequency of the surface wave.

Jan 1, 1998

By William R. Rumbold

THE Kinta valley in the State of Perak, one of the largest of the Federated Malay States, is probably at the present time the richest alluvial tin-district in the world, Perak producing from 20,000 to 25,000 tons of tin annually, and the Kiuta valley being the chief producer. The valley runs approximately north and south, and is 30 miles long by 12 wide. It is very flat, the mountain-ranges on either side rising abruptly from the plain, that on the east being the great Central range of the peninsula, and that on the west a subsidiary range marked " Kledang " on the map, Fig. 1. The valley is drained by the Kinta river, which rises in the eastern mountain range and flows south to join the Perak river, being joined by numerous streams from both mountain-ranges. The rain-fall is heavy, averaging annually about 90 in. The whole country is covered with dense jungle, except where it has been cleared for mining-operations and a small amount of cultivation. Mining villages are scattered throughout the valley, the chief towns being Kampar, Batu Gajah, Lahat and Ipoh, the latter being the center of the mining-operations. An ideal section of the main geological features of the Kinta valley is given in Fig. 2. The valley is composed of a highly crystalline limestone, usually white in color, sometimes gray; in fact, it may be called marble. It is always highly inclined and often contorted, and in some places is interbedded with shale. On the east side of the valley, near its contact with the granite, it forms a remarkable series of limestone cliffs, which rise in some cases as high as 2,000 ft. above the level of the limestone in the valley. It is non-fossiliferous, and its geo-

Sep 1, 1906

By James Vaughan

Australia is a major miner of ore that requires hydrometallurgical processing. According to the 2016 US Geological Survey Minerals Commodities Summaries, the country is 1st for aluminium (bauxite) and lithium, 2nd for gold, zinc and cobalt, 4th for nickel and silver, and 6th for copper mining, not to mention its wealth in coal and iron ore. In this paper, examples of recent Australian hydrometallurgical activities are summarised. Then, selected research projects from the University of Queensland hydrometallurgy research group are profiled. The projects profiled are related to fundamental aspects of processing bauxite with organics and reactive silica as well as the development of a synergistic hydro- and pyrometallurgical process for copper. The process context and motivation for the research is introduced, key results are highlighted with the associated relevant references.

By F. W. Gray

IN 1922, the writer communicated to the Institute a paper entitled The Development of the Coal Industry in Canada (1), which summarized the considerations set out in a series of papers (2) concerned with coal-mining in Canada which he had presented in 1920 and 1921. This paper contained a forecast by decades, commencing 1920, of Canadian coal production, importation, consumption, and exports, based on anticipated rate of population increase, and continuation of the gradual increase in the per capita rate of coal consumption in Canada that had taken place every year up to 1920. The following comparative statement brings our the differences between the forecast and actual experience:

Jan 1, 1936

By Cang Daqiang, Li Yu, Liu Xiaoming, Zong Yanbin

"Utilization of high-quality heat in melting slag is a great challenge for iron and steel industry. In the paper, a new method is put forward to concurrently utilize heat and slag by converting the melting slag directly into high valued materials, slag glass-ceramic. A glassceramic with a higher basicity of 0.7 than traditional basicity of 0.45 was prepared from steelmaking slag in order to utilize more hot melting slag. Effects of Alz03 on its crystallization processes were researched by XRF, DTA, XRD and SEM. Results show that Alz03 in glassceramic would have great effected on its property. When the Alz03 content ranges within 12%-15%, glass-ceramics with basicity of0.7 could reach the best performances. The change of dominant phase in glass ceramics from akermanite and wollastonite to akermanite and gehlenite would significantly degrade its mechanical property. An increase of Al2O3 content leads to a rise of the viscosity and crystallization activation energy of the glass, while results in increasing sintering temperature and crystallization temperature of glass, which contributed to its fully crystallization and densification process.IntroductionSteel slag is a by-product under a process of converting iron to steel at above 1600°C, and 0.1-0.15 ton molten steel slag would be discharged for producing per ton of steel in the process. The discharged steel slag at 1600°C has heat of 68 kgce/t. In 2012, China's steel output reached 716 million tons, and produces about 100 million tons of steel slag and 68,000 tee of heat in it [1,2]. But at present, utilization of both slag and its heat at 1600°C is a great challenge for iron and steel industry.Dry granulation of melting steel slag by air and then recovering the heat of the hot air are a traditional technology which have not yet been put into practice for very low heat conductivity of the slag and low efficient of heat exchange among the different processes [3,4]. Therefore, a new method for high efficient utilization of both steel slag and its high temperature sensible heat is put forward [5,6], which is on-line reducing and extracting iron from molten steel slag and then directly preparing glass-ceramic by use of the residual molten slag."

Jan 1, 2014

By J. Petit, P. Girard, A-M. Gilbert, D. Faucher

L&apos;annee 2000 a été une année stratégique et significative pour l&apos; Aluminerie de Bécancour dans la réduction des gaz a effets de serre. L&apos; équipe s&apos; etait donne comme defi un jour d&apos;arriver a l&apos;objectif de zero effet d&apos;anode dans les sa11es de cuve (720 cuves au total). Le cha11enge s&apos;averait tres ambitieux car la fa<;on d&apos;alimenter une cuve d&apos;electrolyse pour obtenir son maximum de rendement faraday est de travailler le plus pres possible de l&apos;effet d&apos;anode pour eviter l&apos;embourbement de ce11es-ci. Ceci signifie que techniquement nous a11ons en moyenne, quotidiennement, 12500 fois pres de l&apos;effet d&apos;anode sur !&apos;ensemble de nos 720 cuves qui produisent aujourd&apos;hui environ 405 000 tonnes d&apos;aluminium liquide annuellement. Des 695 kg equivalent en C02 par tonne d&apos;aluminium produite en moyenne annue11ement, de 1990 a 2000, nous en sommes rendus ace jour a environ 35 kg equivalent en C02 par tonne produite. Nous sommes pres d&apos; atteindre notre objectif mais les demiers gains sont plus difficiles a atteindre. Les strategies d&apos;automatisme et d&apos;informatique, incluant l&apos;aspect de !&apos;implication humaine sur les bonnes pratiques de travail sur les cuves d&apos;electrolyse, sont les cles de ces resultats.

Jan 1, 2006

By Sidney A. Suhler

A field operable, breadboard model, borehole radar was developed for the detection of hazardous geological anomalies in and above a coal seam in advance of mining. A four-inch diameter downhole probe was fabricated and tested in several environments. The radar transmitter was also employed in a cross-hole or through transmission mode to determine natural geotechnical and man-made conditions between boreholes. Sensitivity to underground conditions in both modes of operation were indicated.

Jan 1, 1978

By R. A. Horn, S. M. Telfer

"Canada has a per capita GDP second only to Japan among the G7 countries and a positive trade balance which ranks third among the world&apos;s major economies. International trade represents a very large part of the national economy and as a proportion of GDP is larger than that of all the other G7 countries with the exception of Germany. On the negative side the Canadian current account deficit relative to the size of the economy is significantly worse than that of all major industrial countries, due mainly to the cost of servicing an immense foreign debt and to a large and worsening negative trade balance in manufacturing.The outflow of money may be reduced by increasing the productivity and competitiveness of those sectors of the economy in which Canada already has a leading competitive position and which have the potential for further growth. The mining industry is uniquely qualified in this respect in that Canada is the western world&apos;s largest producer of metals and mineral products and has the geology and the exploration skill to replenish reserves assuming that an adequate level of investment is maintained. In 1989 the minerals industry contributed $8 billion to the country&apos;s balance of payments and with the exception of forestry is the only sector of the economy which has shown consistently increasing foreign earnings over the long term.In recent years there has been a decline in exploration in Canada and a significant increase in countries such as Chile. The demand for hard currency to finance the development of the newly emerging capitalist economies of the CIS and Eastern Europe is also driving these countries to seek foreign investment to allow them to exploit their natural wealth more efficiently. Canada is therefore facing growing international competition for risk capital and in the future its trade surplus will probably decline in the face of lower cost foreign production.Canada rightly exercises a high level of environmental control on its mining operations; however a significant deterrent to investment is the fundamentally unjust application of the many provincial and federal environmental laws, under which a mining company, even if it takes every measure to protect the environment, runs the risk of eternal and unlimited future liability. If this situation is not rectified the effect will be an increase in global pollution as mines in countries with more lax application of law and regulations controlling environmental damage replace those of Canada. Tax benefits and incentives are a more efficient means than arbitrary regulations in minimizing environmental damage."

Jan 1, 1994

During the past decade, the miner-al industries have been faced with an increasing shortage of engineers. The point has now been reached where the shortage may be termed critical. This shortage may be attributed directly to declining enrollment in the mineral science programs offered by the universities on this continent. Although the reasons for declining enrollment are undoubtedly many, two major hypotheses may be postulated. The first is that high-school graduates are either unaware of the mineral industries and the opportunities in them or that they are aware of them but have somehow obtained a false image of their true nature. The second is that they are aware of the true nature of these industries and the opportunities they offer but find them exceedingly unattractive. The problem of dwindling enrollments has, in recent years, been subjected to a concerted attack by the industries and professions concerned. However, their efforts to date have been based essentially on the first hypothesis. Sufficient results are now available to suggest that either the methods of attack are inappropriate

Jan 1, 1965

By Fred C. Turin

The U.S. Bureau of Mines conducted a human factors analysis of hazards associated with roofholting activities in underground coal mines. Emphasis was placed on hazards related to the movement of the drill-head boom or mast of a roof bolting machine. The objective was to identify hazards and recommend solutions. The data-collection effort consisted of analysis of U.S. Mine Safety and Health Ad-ministration accident data; visits to underground mines and interviews with experienced roof bolting machine operators; discussions with roof bolting machine manufacturers; interviews with workers injured while performing roof bolting tasks; and reviews of research on roof bolting safety. A set of recommendations to increase the safety of roof bolting operations was developed. In particular, the following list of recommendations was presented in ranking order: (1) use an interlock device to cut off power to controls when an operator is out of position, (2) place fixed barriers at pinch points, (3) provide appropriate control guarding, (4) reduce fast-feed speed, (5) use automatic cutoff switches at pinch points, (6) redesign control bank to conform to accepted ergonomic principles, and (7) use resin insertion tools and resin cartridge retainers.

Jan 1, 2010

By E. M. Cameron

Reconnaissance radiometric and geochemical data have been obtained for an area on the western shore of Wollaston Lake that includes the Rabbit Lake uranium deposit. The study area is extensively drift cover ed. The geochemical data were obtained by analysis of center-lake sediments and surface waters for a variety of elements and other constituents. The airborne radiometric data comprise measurements of eU, eTh and K obtained with a .50,000-cc NaI (Tl) detector at a mean terrain clearance of 120 m and 5-km flight-line spacing. Uranium in lake sediments and uranium in waters are the most effective geochemical indicators of uranium mineralization; the other elements measured are not notably anomalous. A sample site density of one per 1 8 km 2 is more than adequate for identification of the mineralized area. Because many water samples contain close to or below the current analytical detection limit of 0.05 ppb U, the use of sediments is generally favoured. for broad-scale reconnaissance in the region. Uranium in these lake sediments appears to be little influenced by variations in the organic or iron and manganese content. The most effective radiometric indicator of the mineralization is the eU/eTh ratio. This parameter is less influenced by environmental variation on the ground beneath the flight line than eU alone . The eTh/K ratio is anomalous under the Athabasca Formation unconformity where, in places, the uranium mineralization is localized.

Jan 1, 1977

By Patrick Chabot

Ce document présente une méthode hybride de long trou favorisant une méthode de minage initiale par chambre-magasin et complétée par une méthode de minage long trou. Cette méthode a été adaptée suite à plusieurs facteurs tels qu?une géologie complexe, une rareté de mineur d?expérience et un haut taux de roulement de main d?oeuvre spécialisée. Cette méthode a permis d&apos;excellents résultats par rapport à la dilution. De plus, la récupération de pilier à haute teneur par forage long trou sera expliquée. Cette méthode permet aussi de récupérer le minerai qui est resté accroché dans les chantiers chambre-magasins. Introduction : La mine Géant Dormant est une mine filonienne d?or située à environ 80km au nord de la ville d?Amos au Québec. Elle est en opération depuis 1988 et à la fin de 2007, elle a produit près de 885 000 onces d?or à partir d?environ 2 400 000 tonnes de minerai pour une teneur moyenne d?environ 11,5g /t Au. Cette mine est la propriété d?IAMGOLD Corporation depuis l?acquisition de Cambior par cette dernière au mois de novembre 2006. Elle emploie 151 employés permanents et environ 41 entrepreneurs.

Feb 1, 2008

By Fernando Hernández Polanco

Transportation and handling metals and alloys from mills to consumption factories as well as dosing in conventional processes with ingots and scrap has always been considered a complicated activity with high operating costs. Several manufacturers of ferroalloys willing to solve these problems have chosen an alternative for their products that can be used to secure, during transport and dosage in the processes to making special steels, with more efficient consumption of ferroalloys. The trend for the production and sale of ferroalloys is to provide the product in the form of granules packed in bags or in bulk. In this paper we will show you how the granulation process was developed and rapidly adopted the ferroalloys industry as an effective solution to reduce operating costs, create cleaner and safer working environments.

Oct 30, 2017

El presente texto describe las ventajas del uso del sistema de vectores aplicados en la explotación de los minerales de la mina de Atacocha. Este sistema consiste en dividir el Ore Body a explotarse, en varias partes y que al momento de hacerlo sea de forma alternada, como si se tratase de "Stopes" independientes. Entre las ventajas obtenidas por este sistema, está que el desarrollo de derrumbes se hace menos frecuente debido a que las paralizaciones -ya sea por los derrames de minerales de las cajas de Ore Bodyi -, no delimitan un detenimiento total del área de explotación, sino solo a un sector. Otra ventaja estriba en que el costo por toneladas de todos los stopes trabajados, es menor que el sistema de cuadros empleado. Asimismo, para que el sistema sea completamente efecivo, se deben conocer los límites del Ore Body, a través de los análisis y las muestras de laboratorio permanente.

Jul 20, 1957

DURING the early part of August, 1880, I was directed by Prof: J. P. Lesley, State Geologist, to assume charge of the geology and mapping of the Second Geological Survey of the anthracite coal-fields. I visited the region unineumbered by any instructions other than this, that I should submit a plan for making the sur- * In the practical application of this method I wish to acknowledge the valu¬able aid rendered by my assistant, Mr. A. W. Sheafer.

Jan 1, 1881

By M. B. Daza, B. Lattimer

"Even with modern detection and firefighting techniques, mine fires continue to be a safety concern. However, some underground mine fires can be addressed with the remote application of high expansion foam, reducing firefighter exposure to hazards. The flow of this foam can be numerically or computationally simulated in order to gain a better understanding of its behavior, but rheology parameters are needed as inputs to produce accurate simulations. For this reason, this work studies the rheology of firefighting high expansion foam using a foam generator and Poiseuille –Flow Rheometer. Rheological parameters for foams with expansion ratios between 250-1280 are represented by the consistency index (k) and the power law index (n) due to the results show a strong agreement with the Power Law model for non-Newtonian fluid viscosity. Furthermore, experimental results show that high expansion foam behaves as a shear thinning fluid with a power law index around 0.4 and viscosities in the range of s 0.1 Pa-s and 0.042 Pa-s under shear rates between 44 ??-1 and 187.3 ??-1. INTRODUCTION High expansion foams are called to foams with expansion ratio greater than 200. Expansion ratio (??) is defined as the ratio between the volume of foam produced (i.e. volume of foam solution and volume of gas) and the volume of foam solution used (NFPA 2014). Because of its high expansion ratio, one of the most important application of high expansion foams is to fill or flood large spaces such as hangars, storage facilities and underground mines for fire suppression. The foam can fill large structures using small quantities of foam solution within a short time (Sthamer 2012) (Martin 2012). Although the specific high expansion fire suppression mechanism has not been understood on a quantitative basis, a possible mechanism is fuel isolation when the foam act as a physical barrier between oxygen and the flame. Furthermore, as a consequence of this contact water is evaporated, causing cooling of fuel and surrounding air. Besides, water vapor as product of water evaporation causes a dilution of oxygen concentration available to the fire (Fleming and Sheinson 2012). High expansion foam can be applied remotely by means of conduit pipes or in situ close to the fire. In most of the underground mines scenarios, fires have to be addressed remotely to reduce miner and firefighter exposure to the hazards (Smith et al. 2005). Although high expansion foams should not be blasted and must be deposited directly on the area of application because of their low density (Harding et al. 2016) sometimes it is complicated to apply it directly to the fire due to complex access areas at underground mines. In these cases, foam has to be applied far away from the fire. Despite of this fact there is a lack of knowledge in terms of rheological behavior of high expansion foam under high shear rates (Gardiner, Dlugogorski, and Jameson 1998). Furthermore, there are a few attempts to simulate numerically the high expansion foam flow due to the ignorance of its rheological parameters and its complex behavior. (Weaire 2008)."

Jan 1, 2018

By W. H. Emens

[This circular is one of a series dealing with tie development and equip¬ment of small and medium size mines, and with the costs of such work prior to productive operation. The preparation and publication of these papers by the Bureau off Mines has been made possible through the cooperation of various min¬ing and development companies. The bureau of Mines has published a series of circulars dealing with min¬ing methods and costs at a large number of producing nines in the United States, Canada, Mexico, an, other countries. Unit costs of development work, shaft sinking, (rifting, crosscutting, tunneling, and raising are usually much higher in the preliminary development of a property than during its productive life.]

Jan 1, 1933

By Nishit Patel

Development work on the use of plasma torches in blast furnace ironmaking was completed in the 1980s. The technology developers planned to reduce blast furnace coke consumption using electrical energy and large scale coal injection through the tuyeres. Since this time, Westinghouse Plasma Corporation has improved torch reliability with industrial experience in solid-waste-to-energy facilities, as well as metallurgical applications. As coke makes up one-third of the hot metal cost, savings efforts frequently seek to lower coke consumption by increasing process efficiency or replacing coke with cheaper fuels. Alter NRG and Hatch assessed the merits of using plasma torch technology to superheat the hot blast. Coke rate savings, electrical purchase requirements, and a financial analysis to implement the torches are presented.

Aug 17, 2017

By Nikhil Dhawan, Amit Barnwal

The present study reports a processing route to recover metals from integrated circuits of discarded random access memory (RAM) units containing ~ 66% printed circuit boards and ~ 33% integrated circuits. The integrated circuits are manually separated, grounded, classified, and subjected to water fluidization for the effective separation of metals. The significant separation was achieved via water fluidization, and the underflow fraction was magnetically separated. The magnetic fraction was thermally exposed in a muffle furnace, and the process optimization was carried out using a Box-Behnken statistical design. The detailed characterization at subsequent steps significantly aids the understanding of metal-plastic separation and enrichment. A concentrate containing 97% metals (Fe-59%, Ni-9.5%, Cu-7.7%, Sn-13.4%, Pb-5.6%, Ag-1.6%) with 96 wt% recovery can be recovered from discarded IC units. The process pursued is simple, adaptable, and environment-friendly, and the product can be used in conventional smelters.

Jun 23, 2020

By L. Zhou, J. P. Rider, T. W. Beck, J. A. Organiscak, Y. Zheng

The National Institute for Occupational Safety and Health’s Office of Mine Safety and Health Research recently developed a series of models using computational fluid dynamics (CFD) to study the gas distribution around a continuous mining machine with various fan-powered flooded bed scrubber discharge configurations. CFD models using Species Transport Model without reactions in FLUENT were constructed to evaluate the redirection of scrubber discharge toward the mining face rather than behind the return curtain. The following scenarios are considered in this study: 100 percent of the discharge redirected back toward the face on the off-curtain side of the continuous miner; 100 percent of the discharge redirected back toward the face, but divided equally to both sides of the machine; and 15 percent of the discharge redirected toward the face on the off-curtain side of the machine, with 85 percent directed into the return. These models were compared against a model with a conventional scrubber discharge, where air is directed away from the face into the return. The CFD models were calibrated and validated based on experimental data and accurately predicted sulfur hexafluoride (SF6) gas levels at four gas monitoring locations. One additional prediction model was simulated to consider a different scrubber discharge angle for the 100 percent redirected, equally divided case. These models identified relatively high gassy areas around the continuous miner, which may not warrant their use in coal mines with medium to high methane liberation rates. This paper describes the methodology used to develop the CFD models, and the validation of the models based on experimental data.

Jan 1, 2015