Search Documents

By Terry J. Close

At the request of the Idaho Congressional Delegation, the U.S. Bureau of Mines Western Field Operations Center investigated the mineral resources of the 140,000-acre Red Mountain roadless area, located northeast of Lowman, in central Idaho. The area includes U.S. Forest Service Red Mountain RARE II area (4-063). The highly mineralized road less area is underlain mainly by granitic rocks which are transected by a northeast-trending fault system. Associated with the granitic rocks and fault system are gold and black sand mineral resources. At least 1,395 ounces of gold and 858 ounces of silver have been recovered from six lode and placer mines within the roadless area. A total of 525 tons of columbium-tantalum, 2,049 tons of euxenite, 83.5 tons of columbite, and 54,862 tons of ilmenite concentrates have been produced from a nearby black sand mineral placer. Mine workings and facilities in the roadless area consist of two dismantled mills, 15 open and caved underground excavations totaling about 2,900 ft of workings, seven large pits and quarries, over 166 smaller dozer-and hand-dug prospect pits and trenches, and in excess of 66 drill holes. The mineralized sites in the roadless area are covered by about 690 current (1992) mining claims. About 130 individuals are holding the claims. Also within the roadless area are four patented lode mining claims. Twenty-five of the 54 mineralized sites identified during the study of the roadless area have, or likely have, mineral resources. One has gold and three have black sand mineral resources that are marginal or subeconomic. There also are two hot springs with thermal water resources, some veins that could be sources of decorative quartz, and dimension stone which was quarried in the past and could be again.

Jan 1, 1993

By Kris Inwood

"In 1879, when the Dominion government initiated its controversial program of industrial promotion, iron smelting in Canada was limited to one company producing coke iron on the mainland of Nova Scotia and three small charcoal blast furnaces in Quebec. There was no steel production. By the eve of the First World War, iron and steel were being produced in very large quantities, the companies active in 1879 had disappeared and new centres of integrated iron and rolled steel production at Hamilton, Sydney and Sault Ste. Marie had come to resemble the industry as we know it today. The most dramatic change was that at Sydney, Nova Scotia, where in the early 1900s, two steelmaking companies established works. The Sydney developments have been explained as the result of resource discovery and technical change. W.J. Donald, in his authoritative account of the Canadian iron and steel industry, observes:(1) ""The most rapid growth of the Canadian iron and steel industry has occurred since 1897 ... The remarkable growth has been caused largely by the new conditions of the industry. The discovery and use of Newfoundland ores, together with the availability of Cape Breton coal, has made the Nova Scotia industry not only possible but profitable .... It is a safe conclusion that the Canadian industry would not have been an important one, had it not been for the discovery of the Michipicoten and especially the Wabana (Newfoundland) ores:' Donald also argues that metallurgical progress had been necessary to render the ores valuable. ""Newfoundland ores ... contain a considerable amount of phosphorus, and were made available for steel-making by recent inventions:' The purpose of this paper is to re-examine Donald's story. It will be argued that the origin of steel-making at Sydney is somewhat more complicated than Donald has indicated. The difficulty with Newfoundland ore extended beyond its phosphorus content and a resolution required more than the basic open hearth furnace identified by Donald. Moreover metallurgical change was only one of several developments necessary to induce industrial investment at Sydney. Surprisingly, however, the discovery of iron ore in the late nineteenth century does not appear to be part of the explanation."

Jan 1, 1999

By Patrick D. McMaster

"INTRODUCTION According to the Roane Iron Co. of Rockwood, Tenn., the Chamberlain. Barnardville iron deposit produced approximately three million tons of iron ore previous to 1928. The deposit is divided into two synclinal bodies termed the north and south synclines. Production has come from the northern extremities of both bodies.The need for developing additional iron-ore reserves during the war prompted the Bureau of Mines to initiate an exploratory program on the Chamberlain-Barnardville deposit in February 1944, which continued until December 1944.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests. Both these branches are under the supervision of Dr. R. S. Dean, assistant director."

Oct 1, 1946

By Magnus Ericsson

The unexpectedly quick recovery in world crude steel production in the second half of 2009 was due almost entirely to increased production in China that began in late 2008. Previous peaks in monthly production in China were matched by April 2009. The rest of the world had still not reached pre-crisis production rates by May 2010. Chinese production drives growth, but there has been some growth in most other larger crude steel producing countries as well, compared to production in 2009. If the production rate of the first four months of 2010 continues, the total output of crude steel in 2010 will be somewhere around 1,410 Mt (1.5 billion st), the same as in the record year of 2007.

Jan 1, 2010

By Charles G. Patmon

This paper describing the methods of dredging and treatment of gold-bearing gravels at the Lancha Plana Gold Dredging Co.'s dredge is one of a series of similar papers being prepared by the Bureau of Mines on mining practices, methods, and costs in the various mining districts of the United States. The dredge is located near the Mokelumne River, 12 miles west of San Adreas, Calif.; it is accessible by an improved dirt road from Jackson, which is about 20 miles distant.

Jan 1, 1932

By G Kirk

Definition and delineation of in-pit ore and waste material are the most significant tasks for an open pit production geologist; adding or destroying value in the mining value chain. Anglo American’s Mogalakwena Platinum mine, an open pit operation in South Africa moving 100 Mt/a, has recognised the value of improved material definition and is in the process of changing from blasthole to reverse circulation (RC) sampling for in-pit grade control. This is aimed at obtaining more representative samples, which are required to maximise ore recovery, minimise waste dilution and to increase the accuracy and confidence of production forecasts. Early in the project, it was realised that the key risks for implementing RC grade control were related to change management processes, rather than failure of technology. Recognising the importance of this issue, Mogalakwena chose an integrated implementation approach that incorporates all stakeholders of the mining cycle in order to develop a process that delivers maximum value and is sustainable within an active mining environment. The following core goals were addressed over five phases of project implementation: extensive definition and design of integrated project implementation, comprising: project buy-in and ownership from all key stakeholders, including survey, geology, mine planning, drill and blast, load and haul, maintenance, supply chain and finance; and detailed analysis of all potential issues and possible solutions, allocated to stakeholders as part of the scoping process; optimising hole patterns and drilling procedures, focusing on delivering maximum value for minimum cost using multiple scenario analysis from borehole data and operational sequencing requirements; and evaluation of lessons learnt during project implementation in order to optimise the technical solution and operational efficiencies. Although this project is not yet finalised, Mogalakwena Platinum Mine is already providing a blueprint for the effective development, implementation and optimisation of sustainable in-pit grade control RC drilling for other open pit mines within Anglo American plc.

Aug 22, 2011

By Henry N. McCarl

[ ]

Jan 1, 1966

Jan 1, 1985

By AIME AIME

WHEN "Chief" Buehler in mid-September set out on his official 10,000 mile swing-around-the-circle visiting Local Sections he decided not to tell his audiences how to organize and operate a state geological survey. As the director for 28 years, of the Missouri Bureau of Geology and Mines (which, he concedes, is the best in existence) lie could have done this to good advantage; but he preferred to discuss affairs of the Institute. In 25 speeches made to member and student groups, he dwelt on sonic or all of the following phases of activities. He stressed the vital importance of the Local Sections in providing the opportunity for members to associate under pleasant auspices with others in their profession. The benefits of Institute membership he classified as tangible and intangible. Of the two lie felt that the latter were more important. A man's progress in his profession depends in large measure upon a broad acquaintance and friendship with others. The Institute is incomparably the best medium for meeting fellow engineers. The primary, function of the new enlarged Membership Committee is to obtain a comprehensive list of engineers eligible to be members, always hearing in mind that the standards of membership must not be lowered in any degree. These men are to be invited by individual letter to apply for membership. Whether they become members or not is of less importance; but it is vital that no qualified man should be outside the fold for the reason that membership had never been suggested to him. Dr. Buehler emphasized repeatedly his feeling that the younger man that had never had Institute membership brought specifically to his attention had been cheated:

Jan 1, 1935

By R. S. Dean

A large metallurgical experiment station at Salt Lake City to house the works of the Bureau of Mines in the intermountain area properly has long been projected. It finally became possible when a Public Works Allotment of $300,000 was set aside for building and equipment. With the new building assured, the Bureau of Mines decided to move the headquarters of its Metallurgical Division from Washington, D. C., to Salt Lake City, Utah. It was felt that this move would simplify they administrative work of the chief engineer of the division, as all stations devoted primarily to metallurgical work are west of the Mississippi. These include Rolla, Mo.; Minneapolis, Minn.; Pullman, Wash.; Reno, Nev.; Berkeley, Calif.; Boulder City, Nev.; and Tucson, Ariz. In addition to these stations will groups, of investigators working on metallurgical problem, are maintained at Pittsburgh, Pa., and College Park, Md. Salt Like City was clearly a more central point for the direction of this scattered work than Washington, D. C. The building (fig. 1, A and B) was designed from general plans worked out by the authors of this paper. Contraction was begun in March of 1939, and by the end of the year the Metallurgical Division had moved, into its now quarters.

Jan 1, 1940

By J. F. Brune, A. Verma

"Face ignitions in underground coal mines are a major risk for underground mining operations, as they can lead to methane or coal dust explosions. The 2010 disaster at the Upper Big Branch Mine resulted in 29 fatalities due to a methane and coal dust explosion initiated from a face ignition. Much research has been conducted to mitigate face ignition hazards, from water sprays to installing passive and active explosion barriers. Despite the increased use of water sprays in U.S. coal mines, there have been more than 50 documented face ignitions in the U.S. underground coal mines since 2010, indicating that this hazard still prevails. This paper will examine the statistics of face ignitions and gas explosion in U.S. coal mines based on MSHA data. It will study factors contributing to these face ignitions and outline best practices for their prevention based on experience and practices worldwide. INTRODUCTION Methane and coal dust explosions are one of the major causes of coal mine disasters in the U.S. and around the world. Such disasters have resulted in the large number of fatalities and loss of mine infrastructure. The recent explosion at the Soma coal mine in Turkey has caused the death of 301 miners (Mining Turkey, 2014). As documented by U.S. Mine Safety and Health Administration (MSHA, 2015a), the U.S. coal mining industry has also experienced several catastrophic mine explosions with accidents at Upper Big Branch mine, Darby mine, Sago mine and Jim Walter Resources No. 5 mine in the last decade, causing the deaths of almost 60 miners. Every explosion requires a source of ignition, the right amount of fuel and oxygen. In underground coal mines, methane acts as a fuel while ventilation air acts as a source of oxygen. The source of ignition may vary from spontaneous combustion, electrical equipment and switchgear, mechanical heat sources, face ignitions due to friction rock-on-rock or from cutter bits and lightning strikes. Under the right conditions, energy of less than 0.3 mJ is sufficient to ignite methane-air mixtures (James, 2007) that can result in a catastrophic explosion. Much research has been done to mitigate the methane explosion hazard by proper dilution, continuous monitoring of methane and elimination of ignition sources. Historical studies indicate that face ignitions are the major cause of explosion in underground coal mining operations worldwide (Belle, Carey, and Robertson, 2012). Statistics shows that most mine disasters were started from a small face ignition, which turned into a major explosion fueled by additional methane and coal dust (Belle et al., 2012). To investigate face ignition hazards, researchers must study potential ignition sources as well as potential explosive atmospheres near mechanical coal cutting operations. Statistical analysis of U.S. coal mine face ignitions reported by the U.S. Mine Safety and Health Administration (MSHA, 2015b) shows that several factors are responsible for face ignitions."

Jan 1, 2016

By Robert B. Fisher

[The purpose of this paper is to acquaint manufacturers of various types of asbestos product's, particularly those that specialize in materials used for sound deadening, vibration damping, and filtration, with a recently invested depth deposit of paligorskite, a type of asbestos usually called mountain leather. In the past this mineral has been only a museum curiosity but it possesses characteristics that may adapt it to industrial uses. The deposit is on Lemesurier Island, near this entrance to Glacier Bay, in the northern portion of southeastern Alaska, at approximately latitude 58° 17? N., longitude 1360 05' W. The island is about 4 ½ miles in east- west length and miles in width. The property on which the deposit occurs is owned by the locator Joe Ibach, end it was brought; to the attention of the Bureau of Mines by Col. George B. Norris. A Bureau of Mines engineer, accompanied by the owner and Chris Ellingen, visited the property sand examined the open-cuts from May 7 to 10 in 1944. The purpose of the examination was to determine the approximate extent of the occurrence and to obtain samples of the material for identification end study of its utilization.]

Jan 1, 1945

By Mike Dry

Conventionally, lithium-bearing brines are processed via solar evaporation, chemical purification, and either electrolysis to lithium hydroxide or precipitation of lithium carbonate. Lithium-ion battery technology and electric vehicles are forecast to greatly increase the demand for lithium, but not all lithium-bearing brines are amenable to the conventional extraction process and new approaches are being developed. The chemistry associated with conventional lithium extraction is outlined and two new approaches are discussed.

It is a very great pleasure indeed to participate in this interesting and important seminar. My two visits to Australia in the past have been extremely pleasant and this one is equally so. My task is to tell you what has been happening in the United States, in these past few years especially, in regard to the management of our air resources and to present in some detail the difficulties we in the copper, lead and zinc smelting industries have been experiencing. The sudden upsurge in interest in air pollution in the United States is a strange phenomenon indeed - strange because we've had air pollution a long time, just as long as there have been large cities using fossil fuels for heating purposes. And the problem has been studied for quite a long time. As early as 1919 studies by the U. S. Bureau of Mines were done in Salt Lake City, where I .live. In the winter of that year extensive measurements were made of airborne particles - dust and smoke. The average concentration of particles found was 870 micrograms per cubic meter of air. A very large number compared to levels we find today. A microgram of course is a very small unit, one twenty-eight millionth of an ounce. A fine human hair two inches long weighs about 100 Micrograms.

Jan 1, 1971

By M. K. Boateng, K. Awuah-Offei

"Language barrier in a workplace affects workers’ productivity and safety. The objectives of this paper are to: (1) review the various approaches for breaking language barriers among miners; and (2) analyze the costs and benefits of these approaches, and make recommendations on the way forward. The authors achieve these objectives by reviewing the current approaches in breaking language barriers among miners. The review reveals that some of these approaches can be expensive with less benefits. Thus, it is concluded that mining companies should carefully select the optimal approach to break language barrier. INTRODUCTION Multi-national mining companies have expanded their operations into non-traditional mining destinations to grow and meet market expectations. For instance, Newmont Mining Corporation has about 14 operations and projects located in Africa, Asia, Australia and America (Newmont Mining Corporation Operations and Projects, 2015). Similarly, Freeport-McMoRan operates about 14 mines in North America, South America, Southern Asia, and Africa (Freeport-McMoRan Inc., 2015). Some mining companies have also attracted expatriate workers into their workforce. For example, Ma’aden, the Saudi Arabian mining company, in its 2013 annual report states that 34% of its total employees are expatriates (Ma'aden, 2013). Expatriates constitute a key source of skilled labor and facilitate skill transfer. The success of many international operations relies greatly on expatriate performance (Erbacher, D'Netto & Espana, 2006). Even companies that do not expand their operations into other foreign countries still have to deal with language barriers due to changing language demography of the country and the areas from which labor is sourced. For example, the language composition of the workforce and languages used in South African mines is diverse with miners proficient in Afrikaans, English, Zulu, Xhosa and others to varying degrees (Research Focus (Pty) Ltd, 2011). As a result of these trends, most mines today operate with a multinational workforce. This means cultural differences, including language barriers, exist among the miners. Marschan-Piekkari, Welch and Welch (1999) emphasize the fact that language problems become prominent as companies internationalize and grow their operations into more countries. According to a survey by Forbes, language barrier affects operations. For example, business owners acknowledge that language proficiency may promote a safer work environment (Rubin, 2011). A research has shown that language and cultural barriers in a workplace contributes to reducing workers’ productivity, increasing accidents, and hurts employers’ ability to recruit, hire and retain workers (Morris, 2002). Hence, mines are making efforts to break language barriers in their operating environments. Ma’aden, for instance reported in 2013 that 1,506 of its employees received training in English as a second language (Ma'aden, 2013)."

Jan 1, 2016

By H. Huisa, M. Linn Chong

La Evaluación del Potencial en Recursos Rocas y Minerales Industriales (RMI) a través de los Sistemas de información Geográfica (SIG) es un análisis que utiliza el conocimiento que tiene el sector geológico minero para decidir cuáles son las zonas que proporcionan las mejores alternativas para la exploración y prospección de una actividad minera industrial, basándose en características litológicas, canteras y ocurrencias de RMI, concesiones mineras no metálicas, anomalías espectrales de alteración y accesos; mediante un método de Análisis Multicriterio.

May 1, 2008

By Tanai Marin

Modelling of pyrometallurgical processes can become extremely challenging when the process involves complex chemical reactions, phase change, multiphase flows, heat and mass transfer and fluid flow. Traditionally modelling involving complex thermodynamic equilibrium and thermochemistry are treated separately from problems in which transport phenomena are dominant, such as CFD and heat transfer studies. The separation is also necessary due to the lack of modelling tools that can effectively couple both solution thermodynamic and transport phenomena or even multiphysics problems. However, there are, quite often, problems in high temperature process metallurgy in which it is not possible to simplify this two modelling approaches. Typical cases of this are for example, the modelling of slag freezing on furnace walls (electric or flash furnaces) to create a protective layer in front of the refractories hot wall, the formation of build up from the matte or metal phases at the hearth of the furnace, calcine smelting from charging piles into slag phase, etc. The problem is even more challenging in nonferrous pyrometallurgy as most, if not all, of the condense phases are highly non ideal solutions involving several components and exhibiting complex crystallization paths and miscibility gaps, such as the Fe-Ni-Cu-S matte, FeO-Fe2O3-SiO2, FeO-MgO-SiO2 slags, etc. In this paper, an approach to model coupled problems involving multiphysics and solution thermodynamic is presented. The approach consists in developing in-house a library containing the Gibbs energy minimization routines and using the local equilibrium concept for process modelling from a multiphysics commercial software (COMSOL). Simple test cases, such as building a non-ideal binary phase diagram on a CFD package is presented, the limitations and of other classic approaches such as equilibrium or Scheil cooling are discussed and compared to this model.

Jan 1, 2015

By Edmond J. O’Donovan

South Bulga is a new longwall operation located in the Hunter Valley coal-mining region in Southeastern Australia. The mine’s objective is to achieve productivity levels significantly higher than the current industry average. From the day longwall production began, South Bulga’s output was below both budget and industry expectations, primarily because of the poor performance of the conveyor system. In the past, conveyor systems have been seen as an adjunct to the mine plan, not as an integral part. At past production levels, this approach may have been acceptable. In today’s mining operations, the conveyor system must be treated as integral and vital to the mining operation. The conveyor system is analogous to the vascular or circulatory system of the human body. Of itself, the system does not do anything, but if it is not functioning satisfactorily, the mine cannot operate.

Jan 1, 1996

By Satish Kate

Indian limestone mines which are highly mechanized in operation and supply limestone to the cement plants have been quite successful in devising ways and means to optimize blasting parameters, so as to have best fragmentation, powder factor, and cost of excavation. In primary blasting mechanized or manually mixed ammonium nitrate Fuel Oil is quite popular in dry holes, and in case of watery holes conventional packaged slurry/emulsions are being used. In order to avail the low density characteristics of the ANFO, some limestone mines have also used Saw Dust and Rice Husk along with ANFO. A number of field trials have been undertaken to explore the suitability of mixing rice-husk and saw dust with ANFO. Presently, about 10% of rice husk/saw dust is being used only to expand the explosive column. The main technical consideration for the use of saw dust/rice husk, has been to reduce the final density and increase the occupancy of explosive in the blast-hole. This not only lowers the detonation pressure in the blast holes, but also reduces cost of explosive without compromising on the fragmentation quality. Besides, with sleeping of the charge there is no substantial fall in the blast quality.

Jan 1, 2006

By Oliver Bowles

In its geologic sense the term marble is applied to rocks consisting of crystallized grains of calcite or dolomite or a mixture of the two. Although limestone has the same chemical composition as marble it differs in that the component particles of calcium or magnesium car- bonates are granular and noncrystalline. In marble the crystals may be intimately intergrown, whereas limestone is an aggregation of unrelated particles cemented together into a solid mass. In its commercial sense the term marble has a much wider applica- tion. As susceptibility to polish is one of its chief commercial assets, all calcareous rocks capable of polish are classed as marbles. Lime- stones that show little crystalline structure may, if they take a good polish, be classed as marbles. Furthermore, serpentine rocks, even if they contain little calcium or magnesium carbonate, are classed as marbles, as they are commercial substitutes of true marbles.

Jan 1, 1916