Search Documents

By Hemant Agrawal, Arvind Kumar Mishra

Rock breakage using blasting is one of the important operations of the mining industry. The delay timing decides the initiation sequence of holes in the blasts and is a crucial factor to improve the overall blast performance. Blast-induced ground vibration is an undesired yet unavoidable outcome of blasting. Peak particle velocity (PPV) is commonly used to measure the magnitude of blast-induced ground vibration. Channelization and better utilization of explosive energy delay are provided between blast holes using initiating systems. The use of different initiation systems even on the same site results in a very significant difference in the values of PPV generated. Due to scattered delay timings of pyrotechnic detonators, the scaled distance predictor equations obtained become unreliable. The error/scatter in delay timing leads to overlapping of holes and hence increases in maximum charge per delay. In this paper, an analytical approach has been discussed to measure the overlapping of holes during blasting with initiation systems having inherent cap scatter. The analytical approach will be calculating the probable overlapping of holes due to scatter in delay timing and will help blasting engineers to understand the variation in maximum charge per delay due to pyrotechnic based initiating systems. In this study, a total number of 102 blasts were conducted using different initiation systems at two different opencast coal mine and 221 corresponding blast vibrations events were recorded.

Nov 10, 2020

By G. S. Rice, R. V. Wheeler

"In September 1923, a proposal was made through official diplomatic channels by the British Safety in Mines Research Board to the United States Bureau of Mines for ""closer cooperation between the two countries in investigations into the causes and means of prevention of mining dangers."" This proposal was cordially accepted by the Bureau of Mines and was officially approved.In the spring of 1924 cooperation was .formally begun. It contemplated, as stated officially, ""full exchanges of information, a joint program of research, and periodic exchange of personnel so as to assure concordant results. By making the resources of both organizations available it will hasten the attainment of results, will secure better: checks for, accuracy, and in the end will save money for both by avoiding duplication and repetition.""This joint work has been carried-on successfully since that time and has developed valuable results, reports on which have been issued from time to time. The progress report which follows gives the results of the studies and work carried on in 1929.During 1929 all the phases of our cooperative research, begun in previous years, have developed normally. The exchange of formal monthly reports on all programs of mutual interest has been continued and has proved an invaluable, means of maintaining contact between the investigators of both organizations. There has been no diminution in the exchange of routine progress reports on specific subjects or in direct correspondence. The interchange of personnel has been maintained, and we can say that the mutual benefits to be derived from this form of cooperation are so great as to be difficult to overestimate. It leads to an appreciation of methods of research and modes of thought in the interpretation of results obtainable in no other way, and engenders a frankness and intimacy which must continuously enhance the value of future cooperation.Dr. S. R. Katz, who was assigned for service with the Safety in Mines Research Board in April, 1928, returned to America in May, 1929. During his stay in England he completed, in cooperation with members of the board's staff, the equipment of a gas-mask laboratory and designed and tested a new form of gas-mask canister. A publication of the Safety in Mines Research Board dealing with this investigation has been prepared and approved and will .be .issued in the near future. In additions Dr. Katz imparted to those with whom he was associated much of his knowledge and technique regarding his particular subjects. He delivered two lectures to the board's staff, the subjects be ""Gas Masks"" and ""The Intensity of Odors"", and gave papers before the Midland Institute of 'lining Engineers and the Birmingham University Mining Society on the subject of ""Industrial Gas Masks""."

Jun 1, 1930

By J. Alberto Chipoco O.

El presente texto describe el proceso e importancia del programa de seguridad industrial en el país. Dicho estudio comprende la legislación, definiciones, factores que intervienen en la ocurrencia de accidentes industriales (defectos físicos del trabajador, antecedentes, actos inseguros y condiciones peligrosas), estadísticas de accidentes comprendidas entre los años 1958 - 1959 y costo de accidentes industriales. Asimismo, se recomienda que el Perú comtemple la creación del Consejo Nacional de Seguridad para un establecimiento y control de reglamentos para la prevención de accidentes.

Jul 20, 1961

In the spring of 1944 the Congress passed Public Law 290 (58 Stat. 190, 30 U. S. C. Sec. 321) "authorizing the construction and operation of demonstration plants to produce synthetic liquid fuels from coal, oil shales, agricultural and forestry products, and other substances, in order to aid the prosecution of the war, to conserve and increase the oil resources of the Nation, and for other purposes." Section 2 reads: "In order to carry out the :purpose of this act, the Secretary of the Interior is authorized- (a) to conduct laboratory research and development work, and, with pilot plants and semi-works plants, to make careful process engineering studies, along with structural engineering studies, in order to ascertain lowest investment and operating costs necessary to determine the best demonstration plant designs and conditions of operation;

Jan 1, 1948

By N. T. Rempe

Proper use of natural resources is multiple use. Underground space resulting from mineral extraction offers opportunities for deep geologic waste disposal (DGWD) which can solve many environmental problems. U.S. government projects plan to use specially mined excavations to dispose of radiotoxic and mixed waste. DGWD takes careful planning, technology transfer, and true partnership between waste generators and mine/repository operators. Using the experience, accumulated by domestic projects in preparation, and by foreign repositories in operation, U.S. mines can claim their rightful share of the growing market for DGWD.

Jan 1, 1996

By Sahendra Ram, Ashok Kumar, Rakesh Kumar, AMIT KUMAR SINGH, Dheeraj Kumar, Arun Kumar Singh, Rajendra Singh

This article offers an examination of a retreat mining method conducted at the Pinoura Mine in India from 2010 to 2017. The method is atypical for coal mines of India’s coalfields. The method executes depillaring in a single pass and does not require the formation of galleries and support installation in splits, thus, reducing the cycle time. A variety of observations are discussed throughout this work and emphasis is placed on field measurements and depillaring under weak roof (RMR = 40–45). This paper discusses design techniques, specifically the estimation of the snook (remnant pillar) size, and important practical observations after the fact. The execution of this method was eventually conducted in eleven panels.

Aug 4, 2020

By W. S. Sanner

This report describes the commercial application of the launder screen in anthracite-industry fine-coal cleaning operations. No new device, the launder screen has been used since the early part of the present century to size, screen, classify, and deslime the fine-anthracite sizes (Buckwheat Nos. 1 through 5) recovered by "river-coal" men dredging along streams draining the anthracite fields. The launder screen is stationary, has no moving parts, requires ample water for operation, and can be constructed economically on the job. Essentially, it consists of a wooden trough with baffles placed through its width to form a well system. The wells are covered by fine-mesh woven-wire screening. Each well is tapped with a number of orifices, and the hydraulic suction head developed in this manner removes high-gravity fines and slimes through the screening as underflow to waste. Material retained on the screen surface discharges as overflow product.

Jan 1, 1954

By Pierre R. Hines

These notes are based on observations made while on a recent trip through the West, for the purpose of studying the practical operation of the ball-mill. The writer takes this opportunity to express his thanks for courtesies extended at the many plants visited as well as for the valuable data received: While there are several types of ball-mill on the market, particular attention will here be given to the diaphragm type, as the open-trunnion type, especially the conical mill, has been thoroughly discussed in the Transactions. There is a prevailing impression that the ball-mill is a recent development; however, ball-mills were used extensively in Montana and other western states for crushing ores for concentration as far back as 1808. Its present prominence is due in part to its recent successful application by one of the large copper companies. Without any reference to dry grinding, the first successful ball-mill for wet crushing, which is still in operation, was built 10 years ago.l This mill, designed by Erminio Ferraris for crushing Sardinian ores for concentration, is of more than passing interest. It embodies the peripheral discharge with grates, large forged-steel balls, and the principal features of the modern ball-mill. The results approach present-day practice, the chief differences being that the mechanical construction has been improved in the modern types. Crushing Action of Ball-mill The action of the balls and the principles of crushing have been studied by several investigators.2 Their conclusions are confirmed by results obtained by the writer in experimenting with a small machine built at

Jan 1, 1918

By J. J. Forbes

The investigation of major and minor coal-mine disasters has been a routine function of the Bureau of Mines since its inception in 1910, and the facts obtained during such investigations have been used as a basis for determining the precautions that the managements and employees of many mines are observing to forestall similar occurrences. The Bureau has conducted research on roof-control and other mine problems, but a comprehensive study of other fatal accidents was not attempted until February 10, 1950, when the policy of investigating all coal-mine fatalities in the United States was approved by Bureau of Mines Director James Boyd. The investigations are being conducted by Federal coal mine inspectors functioning under the provisions of the Coal Mine Inspection and Investigation Act of May, 1941, Public Law 49; and reports covering the investigations are distributed to management, the State mine-inspection agency, and representatives of the mine workers' organization have jurisdiction at the mine.

Jan 1, 1951

By Peter W. Lipman

In the Rocky Mountain region, variations in Tertiary mineralization correlate with changes in tectonic setting and associated igneous activity that can largely be related to tectonics along the west boundary of the American plate. Successive settings include compressional tectonics and associated continental-arc igneous activity; transitional igneous types associated with intra- and back-arc extension; and basaltic or bimodal basalt-rhyolite assemblages associated with Basin and Range extension in- ward of a growing transform boundary between Pacific and American plates.

Jan 1, 2013

By Rafael de Araujo Silva

As ligas ß-Ti têm sido consideradas materiais com potencial para armazenagem de hidrogênio no estado sólido. A adição de elementos de liga estabilizadores da fase ß, tal como o Nb, retém esta fase metaestável em temperatura ambiente. Neste trabalho a liga Ti-40Nb (at.%) foi produzida via fusão a arco e suas características microestruturais foram caracterizadas visando avaliar os efeitos da aplicação da deformação plástica severa (SPD, severe plastic deformation) e da hidrogenação. A laminação a frio sob atmosfera de Argônio foi a técnica de SPD escolhida. Os resultados principais mostraram que é possível hidrogenar a liga fundida Ti-40Nb em temperatura ambiente após laminação a frio. Os efeitos da deformação plástica severa na microestrutura da liga, como a introdução de discordâncias, foram importantes para o aperfeiçoamento da cinética de absorção em temperatura ambiente (25 °C). Após a dessorção da fase hidreto (CFC) a microestrutura volta a ser constituída pelas fases ? (CCC) e ?” (ortorrômbica).

Aug 17, 2017

By E. D. Gardner, Edmund Stein

"IntroductionMassive sulphides occurring in metal mines are inflammable and furnish the fuel for many mine fires. Actual sampling has shown that dangerous amounts of sulphur dioxide and hydrogen sulphide may occur in mine atmospheres after blasting in massive sulphides. Probably some .of the finer sulphide in the material being blasted burns while it is in contact with the flame from the explosion. It’s also possible that oxygen of the explosive enters into the reaction.That sulphide dusts are explosive under some conditions has long been suspected, but the theory has not been generally accepted as having been proved. Evidence now at hand appears to be conclusive that such explosions do occasionally occur in mine workings in massive sulphides. Information from several mines working in heavy sulphides shows that occasionally, sulphur dioxide in larger amounts than could be expected from the blasting alone are occasionally thrown out into the mine atmosphere during blasting. Accidents have occurred and lives have been lost by men being caught in such gases. Also it appears in a few cases that damage done to timber in stopes by concussions has been greater than could 112.ve been expected from the regular blasts. In most of these cases the unusually large amounts of Sulphur dioxide could only be accounted for by an explosion or by an ignition of sulphide dusts. When this occurs it is probable that the settled dust is stirred up by the first shot of a round, then the dust cloud is ignited by this or a succeeding shot.In one instance, the senior author, while wearing breathing apparatus, returned to a station to take a gas sample immediately after a raise round had been blasted, and encountered a heavy white fume or smoke that was corrosive to the skin and which forced a retreat. The sample, which was taken farther back in a greatly diluted atmosphere, showed a high percentage (0.18) of sulphur dioxide. The station and the raise which was just being started were very dry and the walls and floor of the station contained settled sulphide dust which apparently was ignited by the blast."

Mar 1, 1928

THE CHAIRMAN.- This meeting is under the auspices of the American Institute of Mining and Metallurgical Engineers, and I think the germ of the idea originated in the steel business. Last year there was a meeting of prominent people in the steel industry with the idea of getting together and discussing practical phases of their business, so that everybody could contribute and from that there might be benefit derived for the industry. Several months ago when Mr. Bain was in Salt Lake City, he and Mr. Oldright asked me what I, as an individual, thought of it. From that originated this idea of having the copper people come together to discuss reverberatory smelting and all its phases. In starting out, it seemed the best plan to ask members what particular subjects they wished to discuss first; that is, the ones that would be considered more important. We asked Mr. Oldright, or suggested sometime ago that the meeting be postponed until May because May is a lovely month in Salt Lake. There are a number of attractive features around the city. We have a number of smelters here and I think that probably the most of the benefit will be derived from talking in an informal way and visiting the various plants around. the valley. At any rate, speaking as a resident of Salt Lake, I am glad to see all of you gentlemen here, and hope you have an interesting and instructive time. The tentative list of subjects for discussion at this conference is as follows: Construction Walls, etc. Walls, proper design and thickness of brick for various types of charging. Bottoms, construction of. Binding steel, correct weight and arrangement, where thrust of arch should be taken. Refractory materials, feasibility of using different material in various parts of the furnace. Water jackets, where applicable. Should bricks be used inside of same. Gas space, proper design for, height of roof above bath, etc. Roof Shape of Roof, in hot zone and elsewhere, longitudinally. Construction of roof, in various zones, around openings.

Jan 1, 1930

By Shenghui Chu, Zhibiao Guo, Dongshan Yang, Yuanxin Zhao, Xiaohui Kuai, Jingwei Gao

The technology of automatically formed roadway without pillars (AFRP) via roof cutting and pressure releasing (RCPR) is a reformatory method for gob-side entry retaining, which automatically creates a roadway by utilizing the fragmenting and expanding properties of rock strata and the mining pressure, to realize a novel technique for coal mining without coal pillars. The Anju Coal Mine is the first kilometer-deep mine where this technology is applied. To conduct a geomechanical model experiment, this research uses the 5307 working face in this mine as its backdrop. The experimental results show that this technology can efficiently decrease the pressure of the AFRP surrounding rock. The roof maximum stress of the AFRP is 21% lower than that of the belt roadway, while the side abutment pressure of the former is 13.4% lower than that of the latter. The comparison of model experiment data and field monitoring data shows that the roof and floor approaching deformations on the roof-cutting side and solid coal side of AFRP differ by 8.8% and 9.6%, respectively. The model experiment results and field monitoring data show good agreement, and the deformation of the AFRP surrounding rock can be successfully managed by this technique. The study’s findings can serve as a guide for using this technology in kilometer-deep coal mines.

Jul 31, 2023

By J. W. Eckerd

This report describes an investigation of the technical feasibility of using a conventional commercial-size (10-ft. i.d.), rotating grate, dry-ash-removal type gas producer to make producer gas from chestnut-size bone anthracite. Test instruments were installed, and some minor changes were made in the equipment to handle the large quantities of materials expected. Extensive tests, lasting about 4 weeks, were planned, using 35 to 50 percent ash chestnut anthracite bone. However, operations were suspended after 8 days when it became apparent that to use this type of fuel satisfactorily substantial changes in equipment and operating procedures would be required. Nevertheless, enough data were obtained to indicate that gas could be produced continuously and routinely from bone coal in this type of producer whenever conditions justified the necessary development work.

Jan 1, 1960

By H. Reginald Hardy

This report describes the results of a research project carried out to investigate the feasibility of using transducer arrays, located on surface or in shallow boreholes, above an active coal mine to detect and locate the source of underground microseismic activity which normally occurs during mining. The initial stage of the project involves the design and development of a self-contained mobile microseismic monitoring facility capable of use in remote field locations. Following this a variety of transducers, and transducer field installation techniques were investigated to obtain optimum sensitivity and high signal-to-noise characteristics. Preliminary efforts were also undertaken to develop semi-automated techniques for analysis of microseismic field data. Using the facilities and techniques developed field studies were carried out at a number of surface locations over a central Pennsylvania coal mine operating at depths of the order of 500 feet. In particular studies were con-ducted over a previously mined development area, troubled by extensive problems of roof instability, and over two longwall panels during mining. Although many of the field studies were carried out during the development stage of the project, results in general have been most encouraging. Limited results were obtained over the development area, however excellent microseismic signals, correlating with underground strata instability, were detected over both long-wall areas, proving the general feasibility of surface monitoring techniques. More recent studies, carried out as part of a subsequent project, and utilizing modified geophone installation techniques at a third longwall site, have verified explicitly the feasibility of measuring underground microseismic activity from surface locations. Sections of typical field data are included in this report along with a brief review of the studies carried out at each of the field sites. Detailed analysis of data obtained at the second and third longwall test sites will be presented in a later report.

Jan 1, 1974

By C. Aldı, O. Yaral

For the more economical excavation of tunnels in underground mining activities, the selection of mechanised excavation machines (such as roadheaders, electro-hydraulic drills, etc.) and the analysis of performance prediction that can be used in estimating machine energy consumption have been subjects of research from past to present. One of the parameters to be considered in studies examining these methods, is the grinding process. The success of increasing efficiency in grinding is expressed by a reduction in energy consumption. The goal of a grinding process is to maximise the grinding amount at the appropriate grinding size while minimising the energy consumption per tonne of the fragmented material. Today, the depletion of high-grade ore deposits has largely directed the mining industry towards low-grade but large reserve ore deposits. This shift has particularly increased the importance of the grinding process, as it is dependent on particle liberation. Grinding is a critical step in reducing the mineral to the appropriate size, and energy consumption poses a significant challenge in this process. As a result, researchers have conducted various studies focusing on energy efficiency and cost optimisation in this field. In this study, the grindability of 7 different coal environment rocks (sandstone, siltstone) from the Zonguldak Basin, Uzulmez Region was investigated. For this, Hardgrove Grindability Index and Bond Work Index tests were conducted. While determining the relationships between grindability and other parameters, the results obtained from the Hardgrove Grindability Index (HGI) test were used. The energy values found in the Bond Work Index (BWI) test were used to evaluate the excavatability of the rocks. Additionally, tests for strength, hardness, drillability, and abrasiveness were conducted to observe the impact of other parameters on grindability. Considering the results obtained from the experiments, significant relationships were found between the grindability of the rocks and other parameters.

Mar 30, 2026

By Oliver Bowles

The National Granite Commission at its annual meeting in Norfolk, Va., in January, 1930, passed a resolution requesting the Bureau of Mines to conduct an economic study of the granite industry. In compliance with this request a preliminary review has been made of trends, in, the production and uses of block granite. Some unfavorable conditions, were, thus brought to light and certain suggestions regarding a. more orderly and consistent growth in the industry are herein discussed. The results of the study axe, presented in this report for the earnest consideration of the industry and comments are invited, not only on this report but as to future work that might be accomplished by the Bureau of Mines. The authors desire to acknowledge many helpful suggestions and comments from Paul M. Tyler of the Bureau of twines and from Harris F. Sherman, secretary of the National Building Granite Quarries Association. Miss A. T. Coons of the Bureau of Mines rendered valuable, assistance through her wide knowledge of granite statistics.

Jan 1, 1931

By L. M. Litz

In reply to Mr. DeVries comments on my paper, I would like to say that it is true, as pointed out by Mr. DeVries, that under some special conditions, the use of high concentrations of hydrogen peroxide might provide higher short term in-situ …

Jan 1, 1982

By G. L. Oldright

In the first paper of this series (R. 1. 4333) on the cooperative work with the Eagle-Pitcher Mining & Smelting Co., changes in the nature of the sinter feed were measured by corresponding changes in the retorting temperatures necessary to distill zinc at the best rates; the firing schedules summarized such changes. In this paper, third of the series, are noted same of the changes in practice that were brought about by the need to treat more fused, glassy, and "hard" sinter, as the operators qualify it. Losses of uncondensed zinc were increased by adding zinc-bearing materials from which? the zinc was readily distillable to hard sinter requiring higher-temperatures for zinc distillation. The rates of zinc distillation were increased by grinding the fuel finer; there were few benefits and loss of dust on grinding the sinter finer, unless the fine ?coal and fine sinter were brought into contact by pelletizing, and the pellets made but little dust.

Jan 1, 1948