Search Documents

By C. Athanassopoulos

Geomembranes have been used in the mining industry since the early 1970s in solution and evaporation ponds, tailings impoundments, and heap leach pads. Traditionally, heap leach pad lining systems have consisted of a single geomembrane liner placed directly over a prepared subgrade of locally available soil. Heap fills are constructed by placing a layer of highly-permeable drainage stone (overliner) over the geomembrane. Crushed ore is then placed on the leach pad in 3- to 10-m (15- to 30-foot) thick lifts, sometimes reaching final heights of several hundred feet. The crushed ore is irrigated with a chemical solution which dissolves the precious metals from the ore. The nature of the chemical leaching solution depends on the metal being targeted. Low pH sulfuric acid solutions are generally used to leach copper and nickel; high pH cyanide solutions are used to leach gold and silver. The metal-laden pregnant leach solution (PLS) passes down through the ore pile and is captured in a drainage system. Metals are extracted from the leach solution and the solution is then recycled back onto the leach pile. When under load, geomembranes are vulnerable to damage from large stones both in the soil subgrade and in the overlying drainage layer. Although intact geomembranes are virtually impermeable, installed geomembranes will have a small number of holes due to imperfect seams or damage during construction and filling operations. These holes serve as open pathways for leakage into the soil below. Smith and Welkner (1995) estimated liner leakage rates ranging from 5 to 10,000 L/ha/day, depending on the type of heap pad liner and level of construction quality assurance (CQA). Thiel and Smith (2003) reported liner leakage rates up to 2,000 L/ha/day for a valley fill facility with heads ranging from 15 to 35 m.

Jan 1, 2011

By John Manka

Emulsion explosives consist of an aqueous oxidizer phase, a fuel phase, and an emulsifier. The ability to use lower-cost sources for any of these raw materials presents an obvious economic advantage to emulsion manufacturers. This paper focuses on using low cost waste drain oils as the fuel phase in emulsion explosive applications. Laboratory studies showed that emulsions made from waste drain oils and agricultural ammonium nitrate prills were usable for emulsion explosives though their shear stability was weak. Customer field results proved that waste crankcase drain oil could replace half of the virgin diesel fuel in emulsion explosives to make an effective emulsion explosive product with a very low cost.

Jan 1, 2003

By H. Sarvamangala

Selective separation of alumina, silica, calcite and apatite from hematite was achieved through microbiologically induced flotation and flocculation in presence of bacteria (B.subtilis) and that of hematite from apatite after interaction with yeast (Saccharomyces cerevisiae). Bacterial and yeast metabolites containing extracellular proteins were characterized from mineral-grown cell free extract. Bacteria and yeast can adhere to mineral surfaces and influence subsequent separation of the minerals. Bacteria functioned as a stronger depressant for hematite, while yeast cells depressed apatite at neutral pH. Selective affinity of the bacterial and yeast cells towards the mineral surface was observed through adsorption studies. Extracellular proteins (EP) were isolated from B.subtilis and yeast. The protein profile of the EP of bacterial and yeast cells grown in presence and absence of minerals was studied. This study has demonstrated the utility and amenability of microbially-induced mineral beneficiation of iron ores through bacterial and yeast cells and their metabolic by products.

Sep 1, 2012

By AIME AIME

THE climax of the various programs and entertainments in connection with the holding of the World Engineering Congress* in Tokyo in October was the complimentary dinner given by the visiting members of the Institute to our members in Japan. At the same time President Bradley conferred an honorary membership on Baron Takuma Dan, the vice-president of the World Engineering Congress.

Jan 1, 1930

By Henry S. Washington

Introduction. It Still Rains On The Choco ! I Well Remember One Evening A Dozen Years Ago, While. Traveling Toward The Town Of Negua In A Small Champa Or Dug-Out Canoe, The Rain Fell So Heavily That I Had To Work My Hardest To Bail Out The Water With A Large Totuma Or Gourd In Order To Keep The Canoe Afloat, The Senegambian Meanwhile Plying His Paddle In The Stern. If Any One Thinks Bailing Is Easy Work, Let Him Scoop Out A Quart Or More At A Stroke, 40 Times A Minute For Half An Hour, And I Venture That He Will Change His Opinion. These Small Canoes Required Only One Paddler, To Make The 3 Miles An Hour Which Is The Standard Rate Of Aquatic Progress On The Choco. Another Time, On The Atrato River, About Six O'clock In The Afternoon, The Rain Fell So Heavily Than An Empty Gourd, 9 In. In Diameter And 4.5 Deep, Was Filled To The Brim In 90 Sec., Timed By A Watch. Such Downpours Are Typical, But Unless Caught In One It Is Not Specially Noticed. These Downpours Seldom Last More Than An Hour, And Frequently Cover Only A Limited Area, Occasionally Falling On One Bank Of A River And Not On The Other. During The Night-Time,' The Rain, If Gentle, Will Usually Last Until Dawn, And Sometimes An Intermittent Drizzle Will Keep Up All Day As Well, Although, As A Rule, It Rarely Rains During The Day. The Rise Of The Rivers, Due To The Rain-Fall, Varies From A Few Inches To Several Feet. One Night In August, 1899, The Spuds Of The Dredge Margaret, Operating On The Atrato River, Showed A, Rise Of 16 Ft., And For 3 Days Thereafter Occurred The Greatest Flood Known In That District For 32 Years. The Dredge Had All Three Spuds Clown, And The 2-Yd. Shovel Dragging On The Bottom. A 0.75-In. Cable Fast To A Stout Tree, 700 Ft. Away, Stretched Tight

Sep 1, 1908

By Y. Luo

"Investigating abandoned mine subsidence is often a difficult task because many factors, both mining- and nonmining-related, can affect the possibility and the formation process of surface subsidence events over abandoned underground room-and-pillar mines. Among them, mine water frequently plays an important role in causing such subsidence events. However, mine water could also serve the purpose of preventing subsidence. The dewatering of abandoned room-and-pillar mines has been identified as the main cause for a number of serious mine subsidence events in the past.In this work, the mechanism of mine water to prevent surface subsidence over abandoned room-and-pillar coal mines was studied. Two mathematical models are proposed to quantify the potential effects of mine water on the structural stability of mine pillars, roof and floor as well as the potential for causing surface subsidence. The models are validated with an actual case. IntroductionThe potential for room-and-pillar mining operations to induce surface subsidence is mainly dependent on the recovery ratio in the underground mines that directly relates to the stability of pillars. Normally, if the recovery ratio is less than 50 percent, the mine pillars are sufficient to support the overburden strata without their collapse in a sufficiently large contiguous area. Consequently, there will be no surface subsidence. However, if the recovery ratio is greater than 70 percent, the pillars are too small to support the overburden strata and can cause immediate surface subsidence. In 1993, a mathematical model and program was developed and proposed (Luo and Peng, 1993) to predict surface subsidence caused by high-extraction, roomand- pillar mining. When the recovery ratio is between 50 and 70 percent, the mine pillars could be loaded near their critical condition and, therefore, the surface subsidence is uncertain to develop. If the surface subsidence did not occur immediately, mine water starts to fill the underground openings. If thick, clay-type rock layers are presented in the mine roof, floor or pillars, they can be considerably weakened by mine water and cause surface subsidence. The techniques to investigate subsidence events over inactive room-and-pillar coal mines caused by the weakening effects of raising mine water to the claystone immediate roof and floor were presented in Luo (2009, 2011)."

Jan 6, 2018

By Sebastião Ribeiro, Leonardo Carneiro Sardinha, Alline Sardinha Cordeiro Morais, Carlos Maurício Fontes Vieira, Sergio Neves Monteiro

The glass tube of spent fluorescent lamps is contaminated with mercury, which might be a serious hazard in the case of conventional recycling by melting with other glasses. A possible solution could be its incorporation into a clay body to fabricate common fired ceramics such as bricks and tiles. The objective of this work is to characterize a type of fluorescent lamp glass waste to be incorporated into a clayey ceramic. The characterization was performed in terms of wettability tests to evaluate the interaction between the surface of the clayey ceramic and glass waste as a function of the firing temperature. The results showed that the contact angle decreased with increasing temperature, reaching a value of 79°, at a temperature of 1100°C, but not sufficient to completely wet the ceramic. However, compatible chemical composition and reduction of porosity by the flow of soft glass waste between the clay particles favor the consolidation of the ceramics structure above 900°C.

Jan 1, 2015

By Carlos Alvarado, Hernan Narea, Jhon Silva, Bryan Townsend, Katherine Gil, Brayan Caceres, Felipe Pontanilla

With the promising development of new technologies, automation in Drill and Blasting (D&B) is on the horizon. The data generated in all D&B activities, which is currently segregated, can be linked to become information and carry a logical meaning. This information can be used to identify critical activities and make decisions regarding corrective measures to accomplish the goals of D&B. Minera Caserones, supporting Alert2Gain (A2G), and Dyno Nobel, has been working on the development of a quality assurance and quality control (QAQC), system for the mine involving all D&B activities. The main variables in the model for D&B include data from the geology of the deposit, drilling, explosive products, and material loading, among others. To create the model, the mine is divided into blasting polygons. Those polygons are part of a block model. The block model is assembled following different rules, such as: • Block sizes of 4m x 4m x 15m, • Classification of the blocks to a particular blasting polygon using a geospatial intersection algorithm, • Algorithms connect all the pieces of data automatically with the minimum of human intervention and populate the block model, Because measuring data for each block is impossible, another set of rules and algorithms completes the model. Dyno Nobel generates an essential set of data for the QAQC system. Explosive truck loading rates and explosive products, among other data, are also included in the system. The system autogenerates reports every hour, and a summary of the results of each mining day (a mining shift of 12 hours) is distributed by email to all responsible persons to identify the critical tasks and then to make the proper adjustments to accomplish the goals of D&B. The information is updated every hour and available through a dashboard for easy and straightforward interpretation. This paper explains the conceptual details of the QAQC system implemented in Minera Caserones, how the data is aggregated automatically from the different sources, shows examples of the type of information in the dashboard, and presents a successful case where a deviation was detected, and the corrective measures that were implemented to keep the performance of the D&B activity. The paper finally discusses the next steps toward an autonomous D&B system based on new AI technologies, with minimum human intervention.

Jan 21, 2025

By G. E. McElroy

The Coeur d'Alene minim, district of Shoshone County, Idaho, has been one of the largest and most active lead-silver producing districts in the United States for the last 40 years. The mines of the district enjoy exceptional natural advantages with respect to ventilation in that the veins apex high on mountain sides and are most often developed to considerable depths, up to 2,000 feet, by adit and crosscut tunnels under conditions that develop large natural draft pressures; the increase of temperature of the rock with increase of depth from surface in at a low rate; and the average surface temperatures are low. These natural conditions have, in the main, resulted in well-ventilated mines with low temperature conditions throughout. However, where the development has been carried to considerable depths below the lowest level of surface entry, natural-draft ventilation has proved inadequate, and mechanical ventilation systems have been installed on the three largest mines of the district. Local conditions, more particularly those in dead-ended working places, have also required auxiliary ventilation by will fan-pipe units in these and other mines. A particular feature of the district is the number of exceptionally long crosscut tunnels that have been driven to provide entry to vein systems from low points adjacent to milling and transporta¬tion facilities. Three of these tunnels are approximately 2 miles long, and lengths of 3,000 to 8,000 feet are quite common.

Jan 1, 1931

By K. M. Mohamed, I. B. Tulu

"Failures of coal ribs are major hazards in underground coal mines. For the period of 2010 to 2014, rib falls were the leading cause of groundfall fatalities and accounted for 35% of all groundfall-related fatalities. Currently, the National Institute for Occupational Safety and Health (NIOSH) is conducting a research project to develop an engineering-based design methodology for rib control in coal mines to reduce rib fall accidents and fatalities in underground coal mines. Numerical models can be used as part of the design methodology provided the models are appropriately calibrated and verified. The paper presents a coal rib model to simulate the mechanism of the coal deformation and fracturing that can lead to stress-driven rib falls. The proposed coal rib model was calibrated against published data from an instrumented rib site at the West Cliff mine in Australia. Fracturing of the coal rib was defined by critical values of shear strain of the coal material and rib displacement. A critical plastic shear strain of 2.8% and a sudden increase of rib displacement of 30 to 45 mm were sufficient to develop a fracture plane in the rib model. Accordingly, a discontinuous rib deformation was achieved and it compared favorably against field monitoring data. INTRODUCTION Coal ribs are the vertical walls of coal formed when entries are developed in a coal bed. Failures of coal ribs are a major hazard in underground coal mines. Furthermore, failing ribs can contribute indirectly to roof and floor instability by increasing opening widths across intersections and entryways. Over the last 18 years, there has been a continual occurrence of injuries and fatalities in underground coal mines due to rib falls. For the period of 2010 to 2014, rib falls (excluding longwall face and bursts) were the leading cause of ground fall fatalities and accounted for 35% of all groundfall-related fatalities [1]. Despite the threat of rib falls, the amount of rib falls and rib support research conducted in the U.S. is limited compared with what has been done in pillar and roof support design. Currently, the National Institute for Occupational Safety and Health (NIOSH) is conducting a research project to develop an engineering-based design methodology for rib control in coal mines to minimize the number of rib fall accidents and fatalities in underground coal mines."

Jan 1, 2016

Mr G. Maude was educated at Huish's Grammar School (Taunton) and Leeds University. He graduated in 1961 with a B.Sc. degree in Mining. Mr E.B. Crocker was educated at Florida Park High School, Witwatersrand Technical College, and the University of the Witwatersrand.

Jan 1, 1985

By Ray Patterson

A planned modification to a cement kiln at the Holnam Portland Cement Plant near Florence, Colorado required the removal of a ring of cast-in-place (CIP) refractory lining. The CIP lining was approximately 14 inches wide, 12 inches thick and 38 feet in circumference.

Jan 1, 1999

Iron control and iron residue management and disposal are significant issues in all zinc production processes. This paper briefly reviews the most important primary zinc production routes and discusses the challenges posed by iron control in each of them. The technologies and strategies that have proven successful in controlling and managing iron are discussed. SNC-Lavalin's experience in designing and commissioning zinc plants provides a unique perspective from which to review this aspect of zinc production.

Jan 1, 2006

By Xiaolong Bi, Shaohua Luo, Longjiao Chang, Shiyuan Cao, Jianan Liu

iliary agent was proposed. The mineralogical transformation and silicon extraction kinetics of laterite nickel ore in alkaline hydrothermal treatment were studied. The effects of reaction temperature (175 ~ 250℃), molar ratios of sodium hydroxide to ore (1.05 ~ 1.2:1), and laterite nickel ore particle size (44 ~ 178 μm) on the extraction ratio of silica were investigated by using the shrinking core model. The results show that the extraction ratio of silica increases with the increase of reaction temperature, sodium hydroxide to ore molar ratio, reaction time, and the decrease of raw ore particle size. The kinetic analysis shows that the separation of silica in laterite ore can be described by internal diffusion model. The apparent activation energy (Ea) of the reaction was 8.87 kJ mol− 1, and the kinetic modeling was established.

Dec 2, 2021

Over 800 mines have closed in Australia in the past 25 years. This paper summarizes the data obtained from those closures and includes all Australian States and Territories and all commodities, including metalliferous, coal and industrial minerals. Twenty five percent of the mines closed due to resource exhaustion or depletion; 24% due to high costs, price drops, or declining grades; 8% due to open pit resource depletion (but with underground reserves remaining) or underground reserves depleted (but plans to open cut remainder) and 7% due to receivership or voluntary administration. The environmental, social and economic impacts of these closures are also significant and include acid mine drainage and impact on mine employees. An understanding of the causes of premature mine closure will better equip mining companies and governments to better manage future mine closures, wherever in the world the mines are operating.

Jan 1, 2007

By Fred Heivilin

A symposium on the characterization and toxicology of mineral dusts was held Sept. 19 and20 in Washington, D.C. The symposium was held to update the minerals industry, the health community, government agencies and academia on the technical, health and regulatory aspects of minerals to be evaluated by the International Agency for Research on Cancer (IARC).In October 1996, the IARC met in Lyon, France, to discuss and prepare “Volume 68 of the IARC Mono-graphs on the Evaluation of Carcinogenic Risks to Humans on Silica, Silicates, Dusts and Organic Fibers.”

Jan 1, 1996

By A. Galibois, M. Fiset, T. Vo Van

"RÉSUMÉUn groupe de 22 objets prov enant des Forges du St-Maurice a été étudié de façon systématique par analyse chimique et examen métallographique afin de préciser leurs caractéristiques et d'en évaluer la qualité métallurgique.La plupart des échantillons de fe r forgé et d'acier sont hétérogènes tant au niveau structural que composition chimique. L'examen de quelques produits fin is a mont ré qu 'on appliquait des traitements superficiels bien que le contrôle métallurgique fût plutôt empirique.AbstractA group of 22 specimens originating from ""Les Forges du St Maurice"" has been systematically studied by chemical analysis and metallographic examination in order to determine their characteristics and to evaluate their metallurgical quality.The bulk of the forged iron and steel samples are heterogeneous from both their microstructure and their chemical composition. Observation of a few finish products has permitted to establish that surface heat treating was applied although its metallurgical control was rather empirical."

Jan 1, 1984

By A. ALLANORE, OLIVEIRA M. DE, D. CICERI, D. P. CHEN

The alkaline hydrothermal processing of K-feldspar rocks in an autoclave can be a pathway to synthesize a potassium fertilizer for tropical soils that is potentially cheaper and more efficient than traditional potash (KCl). When K-feldspar undergoes hydrothermal alteration in the presence of calcium oxide (CaO), it generates a complex mixture of calcium-aluminum-silicate-hydrate (CASH) minerals that incorporate K atoms stochastically in their structure. These atoms are subsequently released, as shown in a test-tube leaching test, indicating a possible uptake by crops. The relationship between the processing temperature and time in the autoclave for the hydrothermal reaction and the resulting mineralogy and elemental release are only partially understood and are investigated in this study. Elucidating that relationship is the key requisite for subsequent techno-economic analysis, and ultimately for the development of a fertilizer that can be considered as a feasible alternative to KCl.

By Alberto Benavides

El presente texto señala la evolución del sistema de energía eléctrica en diversos sectores entre el período de 1968-1977 y así evaluar su demanda en el futuro a través de fuentes hidráulicas. Actualmente, el potencial hidroeléctrico ha sido establecido en 29.257 MW en la cuenca del Pacífico y de 176,287 en la del Atlántico. Del potencial total se considera como factible de desarrollar técnica y económicamente 58,000 MW, lo cual es amplio para los requerimientos de la minería, ya que la actual potencia generada es sólo de 3% del potencial total.

Nov 1, 1980

By Cynthia Belt

"Energy management is critical to aluminum processing given the high energy requirements of melting and processing aluminum. Energy costs have always been a high percentage of the total production costs within this industry. Energy management at many plants relied on better technology that many times required high capital. As carbon management has grown in importance and project payback becomes more critical, a larger view of a plant's process is required. This paper looks at the energy requirement due to current typical practices in overall product recovery, metal loss, utilization, and technology to understand potential methods of reducing overall energy within a plant and within the aluminum processing industry.IntroductionFor many companies that process aluminum, energy is a major portion of their costs that can surpass the cost oflabor. Aluminum processing can include secondary processing of scrap and prime aluminum into sows and/or molten aluminum or casting aluminum by various methods such as direct chill, continuous casting, low or high pressure casting, mold casting, and extrusions. In the case of this paper, we are considering only plants that include the melting process as a portion of their process. The process of melting aluminum takes energy. In most cases, the aluminum must then be heat treated one or more times. Post processing of the aluminum includes rolling mills used for making sheet, extrusion lines, and machining such as saw cuts, drilling, or surface finishes that all take additional energy.While these high energy costs directly affect the profits of the company, energy management within the metals industry is still not widespread. A co=on misconception is that the solution to high energy costs is high cost capital equipment. While state-of-the-art equipment can certainly improve energy efficiency, it is not the only solution. To obtain a truly energy efficient plant, several directions needs to be addressed through an energy management thought process with a wider scope. Impact on potential savings is possible through: product recovery, metal loss, utilization, and new technologies. An understanding of the potential costs and savings from these means is important. Several of these methods provide low cost approaches to saving energy.The background data used in this paper is not a random sample within aluminum processing but yearly averages from various plants in different aluminum processing industries. As is normal in this industry, the plants have been under different corporate management over the years with different strategies for energy management. This data is not meant to be accurate for the entire industry but to suggest areas for energy efficiency work."

Jan 1, 2012