Search Documents

Ilmenite (FeTiO3) is the primary global source of titaniumdioxide which is commonly used as a whitening agent in papermanufacture and a pigment in paint manufacture. In WesternAustralia ilmenite is processed by the Becher process (Becher,1963, Becher et al, 1965) where ilmenite particles are feddirectly into the furnace with coal and heated to form acomposite of elemental iron and TiO2. The mechanism of thecarbothermic reduction of ilmenite has been extensively studied(Grey, Jones and Reid, 1973; Jones, 1973; Grey and Reid, 1974;El-Tawil, Morse and Francis, 1993) and is reasonably wellaccepted.

Jan 1, 1997

By Martin H. Stanczyk

Freezing to dewater typical Florida phosphate rock slime as demonstrated in laboratory tests appeared to have potential commercial use because of indicated moderate energy requirements, good compaction of dewatered solids, and effective recovery of usable water. After freezing, thawing, decanting, and filtering, batch freezing of gallon-size 13.7 percent solids slime samples yielded 42 percent solids products. Cationic amine, used as a process additive, yielded 46.8 percent solids product with significant filter area reduction. Semicontinuous 8 stage freezing tests also produced thickened slimes. Cooling and freezing 13.7 percent solids slime from 30° to minus 10° C required removal of 183 Btu per pound of slime; Carnot cycle calculation indicated that the theoretical minimum energy to transfer this heat was 27.8 Btu per pound. To produce 1 ton of 44 percent solids slime from 13.7 percent sol-ids slime, the calculated theoretical energy required for cooling and freezing was 52.3 kilowatt-hours. During the research heat capacity and heat of fusion data were determined for the slime at various percent solids.

Jan 1, 1971

By Roy E. Williams

1. The major sources of heavy metal ions in wastewaters of the Coeur d'Alene Mining District are effluents from metallurgical processing plants. Effluents from mine operations provide a secondary source for heavy metal ions. Based on data analyzed by the Federal Water Quality Administration, mercury and arsenic are escaping from some mill waste ponds, but they are in the suspended phase. 2. Metallurgical process effluents are combined with mine waste effluents in tailings ponds, consequently, the quality of the tailings pond decant water is highly degraded. The major effect of combining metallurgical process effluents with mill wastes is a drastic change of pH in the tailings pond. This chance may be an increase or a decrease depending on the metallurgical process. The effluent from an electrolytic antimony plant drastically increases the pH in the tailings pond permitting the removal in solution of antimony via the pond decant system. The addition of low pH effluents to the tailings ponds results in a net decrease in pH which makes lead, zinc, cadmium, and copper more soluble, thereby permitting their removal from the pond via the decant system.

Jan 1, 2011

By Jiawang Hao, Qinglong Zhang, Liang Han, Chuhan Wang, Shenfang Chen, Lan Qiao

The surface collapse and surrounding rock failure caused by goaf instability are the mining disasters that cannot be ignored. It is of great value to evaluate the stability of goaf accurately and treat it economically for the mine safety and the maintenance of ecological environment. However, in previous studies based on numerical simulation methods, the spatial complexity and the irregularity of actual goaf were not considered. Therefore, based on the internal space data of goaf obtained by high-precision laser detector, the goaf stability was comprehensively analyzed through Plaxis software and two-stage fuzzy judgment theory in this study. To effectively improve the goaf stability, the optimal backfill parameters for the goaf treatment were obtained by a series of mechanical tests. The research results provide some good references for the stability evaluation and the treatment of underground goaf.

Sep 26, 2023

By Herbert H. Einstein

Appendices A through M contain information that is the basis for many developments reported in the main text (Parts I through V); this information is, however, not needed in applying the research results. Specifically the appendices contain: A: Geology of Sampled Sites B: Comparison of Distribution Forms with Observed Trace Length Frequencies C: Joint Attitude Pole Diagrams D: Resistance and Deformability of Rock Discontinuities E: Resistance and Deformability of Joints - Details of Data Recording Procedure F: Documentation and Details for Simplified 2-Joint Wedge Analysis G: Generalization of the Stiffness Approach H: Inadequacy Due to Simplifying Assumptions in Wedge Analysis I: Rock Slope Reliability Analysis: State of the Art J: Resistance Derivations for Mechanical Model K: Supporting Derivations for Analysis Method DAYLITE L: Supporting Derivations for Simplified 2-Plane Reliability Analysis M: Plots of SLOPESIM Runs

Jan 1, 1979

By J. A. Ober

"In 2016, the estimated value of total nonfuel mineral production in the United States was $74.6 billion, a slight increase from the revised total of $73.4 billion in 2015 (Table 1). Increased construction activity spurred increased production of industrial minerals, especially those used in infrastructure and residential construction. Although starting the year relatively low, prices for several metals, especially for some of the precious metals, began to trend upward. Decreased production of most metals produced in the United States, however, contributed to an overall decline in the value of metal production.Several U.S. metal mines and processing facilities were idled or closed permanently in 2016, including iron ore mines in Michigan and Minnesota; three primary aluminum smelters in Indiana, Missouri and Washington; one secondary zinc smelter in North Carolina; a titanium sponge facility in Utah and titanium mineral operations in Virginia. In addition, in May, the weekly average rig count for oil and gas drilling reached its lowest level since the 1940s when that measurement was first recorded. The reduced drilling activity resulted in decreased production of some industrial mineral products used in the drilling sector. Trends in mineral-related sectors of the domestic economy declined or held steady, except in the manufacturing of nonmetallic mineral products and nonferrous metals excluding aluminum, which increased. Overall, mining trended downward as the result of significant declines in coal mining, oil and gas extraction and metal mining (Table 2). Discussion of mine production is frequently segmented according to the type of materials produced within the broad categories of metals and industrial minerals (also known as nonmetallic minerals). Industrial minerals can be further subdivided as construction aggregates and other industrial minerals. Metals tend to have higher unit values but very low production quantities compared with those of industrial minerals, which have higher production quantities but are lower-valued materials, such as crushed stone or construction sand and gravel. Therefore, for discussion and analysis of the performance of the nonfuel minerals industry, the value of production is used rather than the tonnage produced. Tonnages of construction aggregates are orders of magnitude larger than those for most other mineral commodities thus making direct compar"

Jan 5, 2017

By M L. Cramer, N P. Wines

"On 9 February 2014, bushfire embers landing on exposed coal in a disused pit at the Hazelwood mine in Victoria’s Latrobe Valley ignited a coal fire that burned for 45 days. The fire was the largest and longest burning mine fire to occur in the Latrobe Valley (Hazelwood Mine Fire Board of Inquiry, 2016). Two Victorian Government Boards of Inquiry have been held into the Hazelwood mine fire. The most recent, in 2015, included consideration of the regulation and implementation of rehabilitation practice at Hazelwood and the other two brown coalmines of the Latrobe Valley (Loy Yang and Yallourn; Government Gazette, 2015).The 2015 Hazelwood Mine Fire Board of Inquiry commissioned Accent Environmental Pty Ltd (Accent) to undertake a review of the financial mechanisms for mine rehabilitation and closure adopted in Australia and overseas (Accent, 2015). Specifically, Accent was engaged to identify ‘any practical, sustainable, efficient and effective alternative mechanisms to ensure rehabilitation of the mines as required by the [Victorian] Mineral Resources (Sustainable Development) Act 1990’ in accordance with Terms of Reference 10 (c) (Government Gazette, 2015).The review by Accent included consideration of a range of financial instruments such as bank guarantees, trust funds and insurance. It considered a number of financial assurance systems in operation in Australia, New Zealand, the European Union, Canada and the United States. These systems included: full and discount financial assurance systems predefined liability proportion systems pooled fund systems the use of post-closure financial mechanisms such as trust funds (Accent, 2015).What lessons can be learnt from other jurisdictions? Are there financial mechanisms already in place that could allow the Victorian Government and the mine operators to manage the risk of rehabilitation default3, lower rehabilitation liability, attain site rehabilitation objectives and allow eventual site relinquishment?CITATION:Cramer, M L and Wines, N P, 2016. Global lessons for a local problem – rehabilitation bonds and Victoria’s Latrobe Valley coalmines, in Proceedings Life-of-Mine 2016 Conference , pp 24–27 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 28, 2016

By Felipe Calizaya, Sekhar Bhattacharyya

Noise-induced hearing loss (NIHL) is prevalent in mechanized underground mines. Federal regulations are often not complied with effectively. Miners are also prone to ignoring administrative guidelines and/or personal protective equipment for hearing conservation. As a result, quality of life among experienced miners plummets while occupational risks increase at workplaces. This research focused on auxiliary fans used in underground mines. These fans work at high rotational speed and generate extremely high levels of noise in close proximity to miners. Silencers used are often of little effect due to poor maintenance. A new silencer is tried in the laboratory with the objective of easy maintenance and resulting reduction of noise exposure for miners.

By Irwin H. Cornell

BRIEFLY stated, the history of the St. Joseph Lead Co. is the story of how a group of men, working for ten years as officers without salaries and stockholders without dividends, developed a small mine in Missouri into what became a large and prosperous corporation. Their courage and faith in the scattered surface deposits of lead coupled with the management's engineering vision and sound financial judgment should prove an inspiration to present-day mining operators and investors. In 1717, John Law's company, known as "The Company of the West," was formed in France and letters patent were granted, for a period of 25 years by Louis XV, for exploration in the Mississippi River Valley. One of the underlying purposes of the expedition, headed by Mr. Renault and Mr. La Motte, a French metallurgist, was development of the lead mines in the area now known as Southeast Missouri.

Jan 1, 1947

The copper concentrate market is becoming increasingly unstable. In the early 1990s large concentrate stocks were built up and the glut was cleared only after treatment charges rose so sharply that 'non-traditional' custom smelter capacity, such as in Kazakhstan, could be employed, By 1994 the market had shifted and Western smelters were unable to secure enough concentrates to operate full out. The reason for these sharp swings in the market balance is that virtllally all the recent mine development has been non-integrated. With different companies developing new mine . and smelter capacity, it is inevitable that the pace of expansion in the two sectors will not be coordinated. For many years the Japanese smelters were the major buyers from the new mm-integrated mines. However, Japanese smelter capacity is unlikely to increase appreciably in the future and this stabilizing influence will be very difficult to replace. This paper will examine the likely concentrate/smelter balance over the next five years and will forecast the likely direction of? treatment charges. It will also touch on the critical variables in assessing the viability of new greenfield custom smelter capacity, such as proximity to concentrate sources, by-product sulfuric acid prices and, most importantly, tariff protection.

Jan 1, 1995

By Tom Retka

This three volume final report summarizes the activities and conclusions of this contract. The objective of the contract was to develop noise control modifications on a retrofit basis, for auger miner coal-cutting systems. Manuals were prepared to assist mine shop personnel in retrofitting the auger miner with these noise controls. Final Report Volume I - Details all vibration and acoustical tests conducted in development of the noise controls. Final Report Volume II - Noise Control Modification Manual for the Jeffrey 100-L Auger Miner describes the various noise control modifications to the auger miner, along with fabrication procedures, cost and vendor information. Final Report Volume III - Noise Control Modification Manual for the Jeffrey 94-l Bridge Conveyor describes the various noise control modifications to the bridge conveyor, along with fabrication procedures, cost and vendor information.

Jan 1, 1978

"The 34th International Conference on Ground Control in Mining (ICGCM) was held July 28–30 at the Lakeview Golf Resort and Spa in Morgantown, WV. Ground control experts have gathered at this location since 1981 to share ideas and successes for improving designs and technologies to enhance the stability of surface and underground mining operations. Ground control is important to all mining operations but is particularly crucial to underground mining to ensure miner safety and operational viability.The year’s event had 240 registered attendees with 20 pecent of that attendance being from the mining industry. A remarkable number of industry representatives attended given the challenges currently faced by the mining industry. A true testament to the value of the conference, the performance of Tom Barczak and Steve Tadolini as co-chairs and the drawing power of the many exceptional speakers that have attended the annual event for many years.The conference operates under the direction of a board of directors with the cooperation, wisdom and assistance of a large organizing committee. Visit the conference website, www.icgcm.conferenceacademy.com, to view the membership of the board and the committee and to access previously published papers."

Jan 1, 2015

By Joel Ochoa, Miguel A. Montiel

El artículo da cuenta del estudio de un prototipo de placa de desgaste para chutes de transferencia con un nuevo sistema de sujeción. El sistema fue validado mediante el software Ansys. La innovación no solo está constituida por un nuevo diseño sino también por el tipo de proceso productivo para la fabricación del producto mejorado. Se incluyeron ensayos con torquímetro, que presentaron resultados favorables.

Sep 30, 2019

By R. Michael Digman

Few efforts have been undertaken to date to assess the quality of mandated coal mine health and safety training for new miners and for experienced miners. This study was concerned with the quality and effectiveness of existing classroom health and safety training programs. The study involved field data collection through pre- and posttesting of trainees, audio-taping class sessions, and administering short feedback forms with trainers and trainees at 14 sites in West Virginia, Maryland, Kentucky, and Pennsylvania. Results indicate that goals, methods, materials, and outcomes of existing training programs vary widely among trainers and sites. The report provides less by way of solution to problems, than it highlights the breadth of issues that relate to the question of training effectiveness and quality. The report concludes that additional work by industry, labor, government, and academia is necessary in order to improve health and safety training programs. Recommended steps are: (a) to develop performance standards and measurable criteria in each of the types of mandated training, (b) to develop better training of trainers, (c) to develop expanded training support services. and (d) to undertake further research and development in health and safety training in the mining industry

Jan 1, 1982

By Natalia Novoselova, Javiera Gerding, Alexey Novoselov

Las actividades mineras, tanto de exploración como de procesamiento de minerales polimetálicos, y los residuos resultantes depositados en relaves, emiten partículas de polvo en suspensión. Esta emisión de partículas en el aire es una de las razones de las numerosas preocupaciones sanitarias y medioambientales de las comunidades cercanas. Algunas de esas inquietudes son reales, otras no. En este contexto, la comprensión de los mecanismos y la distribución geográfica precisa de la contaminación relacionada con el polvo asociada a la minería es muy necesaria para la población local y el personal minero. Las áreas con mayor polución deben ser cartografiadas para evitar su uso y recultivadas con vegetación típica de la zona.

Sep 29, 2023

By R. J. Fantel

The Bureau of Mines investigated the resources, costs, capacities, market relationships, and short- and long-run supply of phosphate rock and phosphoric acid. The 206 mines and deposits evaluated in 30 market economy countries contain an estimated 35.1 billion mt of recoverable phosphate rock (demonstrated resource level). U.S. resources are sufficient to satisfy the domestic and export markets for phosphate products well beyond the year 2000. Because of resource depletion at current producers, however, new properties (with higher cost levels) need to be developed if U.S. production levels are to be maintained. Existing worldwide capacity can satisfy expected demand through the early 1990's. Expansion at existing mines or low demand growth could mean that no new property development will be needed before the late 1990's. Worldwide, almost $8 billion could be required for development of new phosphate rock properties between now and the year 2000, given 3-pct annual growth in demand. Most properties that could develop in the 1990's would require price increases of 20 to 50 pct to break even. To earn a 15-pct rate of return on investment, prices must rise to nearly double the present level of $24 to $29 per metric ton.

Jan 1, 1988

By Scott Rodibaugh

El presente trabajo describe las aplicaciones representativas de la PPC (pressure-powered centrifugue) en minería, diseño básico, función y la experiencia de aplicación de OEM de motores. Asimismo se detallará ejemplos de desempeño de campo de la PPC como experiencias en un sistema hidráulico de camión minero, un motor diésel de camión minero y una trituradora de mineral que lleva el circuito de lubricación. De otro lado, se abordan los métodos de análisis de laboratorio para detectar los rasgos clave del fluido y evaluar la condición del contaminante.

Feb 1, 2017

By C. M. Bristow

The mineral kaolinite is one of the commonest minerals in the uppermost 10 m of the continental crust; ranking in abundance alongside minerals like quartz, mica, feldspar and calcite. Only very exceptionally does it possess all the necessary properties needed to make it worth commercially exploiting. The terms 'Kaolin' and 'Kaolinite' are derived from a locality known as 'Kau-ling', in Jiangxi Province, Peoples Republic of China; where samples of a white clay used by the Chinese to make porcelain were first obtained by European missionaries and explorers in the eighteenth century.

Jan 1, 1986

By S. J. Schatzel, R. B. Krog, H. Dougherty

Longwall face ventilation is an important component of the overall coal mine ventilation system. Increased production rates due to higher-capacity mining equipment tend to also increase methane emission rates from the coal face, which must be diluted by the face ventilation. Increases in panel length, with some mines exceeding 6,100 m (20,000 ft), and panel width provide additional challenges to face ventilation designs. To assess the effectiveness of current face ventilation practices at a study site, a face monitoring study with continuous monitoring of methane concentrations and automated recording of longwall shearer activity was combined with a tracer gas test on a longwall face. The study was conducted at a U.S. longwall mine operating in a thick, bituminous coal seam and using a U-type, bleederless ventilation system. Multiple gob gas ventholes were located near the longwall face. These boreholes had some unusual design concepts, including a system of manifolds to modify borehole vacuum and flow and completion depths close to the horizon of the mined coalbed that enabled direct communication with the mine atmosphere. The mine operator also had the capacity to inject nitrogen into the longwall gob, which occurred during the monitoring study. The results show that emission rates on the longwall face showed a very limited increase in methane concentrations from headgate to tailgate despite the occurrence of methane delays during monitoring. Average face air velocities were 3.03 m/s (596 fpm) at shield 57 and 2.20 m/s (433 fpm) at shield 165. The time required for the sulfur hexafluoride (SF6 ) peak to occur at each monitoring location has been interpreted as being representative of the movement of the tracer slug. The rate of movement of the slug was much slower in reaching the first monitoring location at shield 57 compared with the other face locations. This lower rate of movement, compared with the main face ventilation, is thought to be the product of a flow path within and behind the shields that is moving in the general direction of the headgate to the tailgate. Barometric pressure variations were pronounced over the course of the study and varied on a diurnal basis.

Jan 1, 2018

By S. J. Schatzel, R. B. Krog, H. Dougherty

Longwall face ventilation is an important component of the overall coal mine ventilation system. Increased production rates due to higher-capacity mining equipment tend to also increase methane emission rates from the coal face, which must be diluted by the face ventilation. Increases in panel length, with some mines exceeding 6,100 m (20,000 ft), and panel width provide additional challenges to face ventilation designs. To assess the effectiveness of current face ventilation practices at a study site, a face monitoring study with continuous monitoring of methane concentrations and automated recording of longwall shearer activity was combined with a tracer gas test on a longwall face. The study was conducted at a U.S. longwall mine operating in a thick, bituminous coal seam and using a U-type, bleederless ventilation system. Multiple gob gas ventholes were located near the longwall face. These boreholes had some unusual design concepts, including a system of manifolds to modify borehole vacuum and flow and completion depths close to the horizon of the mined coalbed that enabled direct communication with the mine atmosphere. The mine operator also had the capacity to inject nitrogen into the longwall gob, which occurred during the monitoring study. The results show that emission rates on the longwall face showed a very limited increase in methane concentrations from headgate to tailgate despite the occurrence of methane delays during monitoring. Average face air velocities were 3.03 m/s (596 fpm) at shield 57 and 2.20 m/s (433 fpm) at shield 165. The time required for the sulfur hexafluoride (SF6 ) peak to occur at each monitoring location has been interpreted as being representative of the movement of the tracer slug. The rate of movement of the slug was much slower in reaching the first monitoring location at shield 57 compared with the other face locations. This lower rate of movement, compared with the main face ventilation, is thought to be the product of a flow path within and behind the shields that is moving in the general direction of the headgate to the tailgate. Barometric pressure variations were pronounced over the course of the study and varied on a diurnal basis.

Jan 1, 2017