Search Documents

Discussion of "The Ordering Transformation in Titanium-Aluminum Alloys Containing up to 25 at. pct Aluminum" by F. A. Crossley, Trans, TMS-AIME, 1968, vol. 242, pp. 726-30. Dr. Blackburn, in his response, pointed out that the c/a ratio of the Ti-26 at. pct A1 alloy quenched from 900°C is 1.6006 and not 1.5965 as plotted in Fig. 19. An error in transcription was made in preparing Table V of Ref. 1 (F. A. Crossley, Trans. TMS-AIME, 1966, vol. 236, p. 1174). The corrected Fig. 19 strengthens rather than weakens the argument that a martensitic transformation occurs in alloys containing from 15 to 18 at. pct Al. A Study of the Factors Which Influence the Rate Minimum Phenomenon During Magnetite Reduction, by P. K. Strangway and H. U. Ross, Trans. TMS-AIME, 1968, vol. 242, pp. 1981-88. Page 1883 Reverse Figs. 5 and 6. Sigma—Its Occurrence, Effect, and Control in Nickel-Base Superalloys, by J. R. Mihalisin, C. G. Bieber, and R. T. Grant, Trans. TMS-AIME, 1968, vol. 242, pp. 2399-2414. Pages 2403, 2407, and 2414 Arrows should appear on Figs. 4 and 9; a sigma is missing from Table IV; line 2, page 2414, change "case" to "cast". These are published correctly in the bound volume. Index, December Issue There were a few omissions in the Author Index. These have been corrected and published properly in the bound volume.

Jan 1, 1970

By Frank P. Frandina, Michael J. Loehr, Paul E. Gabryszak

The Heartland Corridor Clearance Improvement Project is part of a regional Public-Private initiative to allow double stack container trains a direct route from the Port of Norfolk through Virginia, West Virginia, Eastern Kentucky and into Central Ohio. In the Preliminary Engineering stage, 30 existing tunnels were assessed and 28 were found to need clearance improvements to allow the use of double stack trains. Alternative tunnel enlargement methods were developed to achieve the desired clearance improvements, while maintaining structural integrity and minimizing disruption to train traffic. This paper summarizes the geometric and condition investigations of the existing tunnels, as well as describes the preferred methodologies to achieve the desired clearance. The clearance improvements will be implemented beginning in the summer of 2007.

Jan 1, 2007

By David D. Eyer

In today's world coal market, coal quality is becoming increasingly important. Often the coal quality parameters are one of the crucial considerations in the development of a coal mine. Because of the user's tighter specifications and because of strict environmental regulations, coal producers are being called on to predict with increasing accuracy, not only the quality of their product but also the variability of that quality. This area of reserve evaluation is naturally receiving a great deal of scrutiny. Consolidation Coal Company has developed reliable and sophisticated methods for predicting coal quality, but the company's efforts continue to search for even better techniques. The following is a step-wise summary of The methods currently used by consolidation coal company, with A recent project used as an example. Two of the newer, and as yet experimental techniques will be briefly discussed.

Jan 1, 1980

One of the major changes in the resource industry in the nineties has been the re- internationalisation of the industry. The history of the resource business has been one of companies from the developed world utilising the cash flows from their operations to explore and develop mines in less developed regions of the world. This resource development has progressively generated wealth and economic development, which in tum, has led to a new generation of exploration and mining projects.   InSouth America, Chile had led the way in a mining resurgence, now closely followed by Argentina, Brazil, Venezuela and Peru. Although Chile has long had a significant copper mining industry, the pre-nationalisation phase was driven by American capital; the current phase has been spearheaded by RTZ - BHP at Escondida with Canadian junior companies, in particular, providing major speculative impetus. The Australian junior companies have not been significant in South America.   Although Canadian and USA exploration appears to be in decline, the mining industry, particularly in gold, is buoyant in North America. Interestingly, a number of listed and unlisted Australian companies are active, particularly in United States exploration.   Australian-based companies have dominated the South-East Asian exploration scene, especially in the Vietnam region. To date, the combination of political and legislative uncertainties have failed to lead to significant resource developments in this region. The area remains one of great potential, as exemplified by the exciting developments in Indonesia.   The Philippines has a history of mining, and this has been dominated by both local and North American operators. Both large and small Australian resource companies have a presence in the Philippines, and the development of the copper-gold potential could be impressive over the next decade.   The tales of the undeveloped mineral potential of China are probably rivalled only by the supposed strings of virgin Russian orebodies! Many Australian companies appear to have looked but few have chosen to proceed with Chinese developments. There seems little likelihood that China will, in the foreseeable future, rival South America as a target for Australian and North American resource capital.   Papua New Guinea has had an active, albeit chequered history in mining, with Australia long being the predominant source of exploration and development funds. The developing nation status of PNG has generated extreme uncertainty, with the current exploration scene all but dead. Most recently, the international flotation of Lihir Gold has tested the international and Australian investment community's commitment to PNG resource development.   The Australian exploration scene continues buoyant, although dominated by gold. The base metals scene is generating, on average, one significant base metal mine developed every couple of years. This is probably the fastest rate of significant base metal development in Australia's history.   The gold scene has been one of incredible dynamics, and there is no evidence that this momentum is waning. The development of new exploration techniques, together with a number of the companies reaching a critical size, has added to the momentum in the industry.

Jan 1, 1995

By G. Jandieri

An improved methodology is presented for assessing the economic feasibility and effectiveness of recycling industrial waste. The methodology is based on the break-even control mechanism, but at the same time provides for the introduction of new evaluation criteria such as the threshold of conditionality and the degree of ore substitution. Based on an improved analysis, it becomes possible to more precisely predict recycling efficiency. A more refined determination of the lower limit of concentration of recoverable metals, at which technogenic waste can be assigned the status of secondary raw materials and processed profitably, leads to a significant expansion of the secondary raw material base suitable for recycling. The potential for recycling manganese-containing dust from the production of ferrosilicomanganese, dehydrated sludge from the hydro separation of slags, and cake from the production of electrolytic manganese dioxide at the Chiatura mining enterprise is used as an example. It is shown that with a threshold of –24% Mn content, the highest recycling efficiency can be achieved by the production of low-phosphorus manganese slag and conversion to ferrosilicomanganese using the above waste to replace 40-60% grade III and IV manganese concentrates in the feed.

Jan 26, 2023

By Morris Cohen, William P. Kimball

This paper deals with the calculation of the composition of the infinitesimal trace of alloy that transfers from the liquid to the solid state at each temperature during the equilibrium solidification of a binary solid solution, and which thereby enables the compositions of the coexisting liquid and solid phases to follow along the liquidus and solidus lines respectively during the cooling. A general expression for the composition (6) of the liquid-to-solid transfer at each temperature has been derived: d= Zlxl(xl - P) + Zsxs(P - xs)/Zl(xl - P) + Zs(P - xs) [1] where ZL and Zs are the slopes of the liquidus and solidus lines at the given temperature, Xl and 28 are the compositions of the stable liquid and solid phases at the same temperature, and P is the composition of the alloy under consideration. The 6 equation is valid for the process of equilibrium heating as well as cooling, and may be applied to vapor-to-liquid, vapor-to-solid, liquid-to-liquid, and solid- to-solid transfers if the corresponding equilibrium diagrams are known. The d-versus-temperature curves for two alloys P1 and P2 are shown in Fig. I. In each case, the liquid-to-solid transfer has the same composition as the stable solid phase only at the temperature of the beginning of solidification, and has the same composition as the stable liquid phase only at the temperature of the completion of solidification. At each intermediate temperature, the composition of the liquid-to-solid transfer differs by a finite amount from those of the two coexisting phases. Therefore, during equilibrium cooling, the transfers must merge into the solid phase from the liquid without forming a transition phase; otherwise the condition of equilibrium would be violated. At any given temperature during solidification, the composition of the liquid-to-solid

Jan 1, 1941

By William P. Kimball, Morris Cohen

This paper deals with the calculation of the composition of the infinitesimal trace of alloy that transfers from the liquid to the solid state at each temperature during the equilibrium solidification of a binary solid solution, and which thereby enables the compositions of the coexisting liquid and solid phases to follow along the liquidus and solidus lines respectively during the cooling. A general expression for the composition (6) of the liquid-to-solid transfer at each temperature has been derived: d= Zlxl(xl - P) + Zsxs(P - xs)/Zl(xl - P) + Zs(P - xs) [1] where ZL and Zs are the slopes of the liquidus and solidus lines at the given temperature, Xl and 28 are the compositions of the stable liquid and solid phases at the same temperature, and P is the composition of the alloy under consideration. The 6 equation is valid for the process of equilibrium heating as well as cooling, and may be applied to vapor-to-liquid, vapor-to-solid, liquid-to-liquid, and solid- to-solid transfers if the corresponding equilibrium diagrams are known. The d-versus-temperature curves for two alloys P1 and P2 are shown in Fig. I. In each case, the liquid-to-solid transfer has the same composition as the stable solid phase only at the temperature of the beginning of solidification, and has the same composition as the stable liquid phase only at the temperature of the completion of solidification. At each intermediate temperature, the composition of the liquid-to-solid transfer differs by a finite amount from those of the two coexisting phases. Therefore, during equilibrium cooling, the transfers must merge into the solid phase from the liquid without forming a transition phase; otherwise the condition of equilibrium would be violated. At any given temperature during solidification, the composition of the liquid-to-solid

Jan 1, 1941

By J. C. Keenan

Company-community agreements are widely considered to be a practical mechanism for recognising the rights, needs and priorities of peoples impacted by mining, for managing impacts and ensuring that miningderived benefits are shared. The use and application of company?community agreements is increasing globally. Notwithstanding the utility of agreements, the gender dimensions of agreement processes in mining have rarely been studied. Prior research on women and mining, however, does show that women are often more adversely impacted by mining than men, and face greater challenges in accessing development opportunities that mining can bring, however there is currently little to no guidance for companies, government or communities in terms of bringing a gender perspective to the fore in mining and agreement processes. While it is undisputed in human development literature that investment in women and sensitivity to gender delivers long-term health, education and local development outcomes, a number of key factors remain unexplored in debates about mining and development. These include: women?s participation in agreement processes, the gendered distribution of agreement benefits, and the extent to which impacts and benefits influence (either positively or negatively) women?s development and economic inclusion. This paper presents the results of an applied research project undertaken by the Centre for Social Responsibility in Mining (CSRM) at The University of Queensland and funded by a partnership between the Minerals Council of Australia (MCA) and the Australian Agency for International Development (AusAID). The project sought to connect with practitioners who had been directly involved in agreement processes to hear grounded perspectives on the interaction of gender dynamics and agreements, and connect those experiences with the broader literature. Findings from this study have implications for the role of companies and governments in promoting gender equality and empowerment as part of their commitments to sustainable development. A key challenge for companies will be navigating the territory of cultural norms and gender equality. The authors argue that without consideration of the gender perspective, and appropriate responses, mining agreements may not be inclusive or representative and may exacerbate gender inequalities and fail to contribute to long-term sustainable development.

Aug 1, 2013

By Tomás Chaparro Díaz

El presente trabajo presenta una metodología para evaluar al supervisor de seguridad -en tanto considera el conocimiento y las habilidades personales del mismo. Para ello, se revisa tres maneras de evaluar los factores de eficiencia del supervisor como: conocimento, aceptación y pasión. Dichos factores fueron aplicados exitosamente en la operación I Cerro Corona, (Cajamarca) mediante la fórmula E=QxAxP, basada en la metodología Six Sigma en la operación. De forma que se convierte en una guía para el proceso de selección y genera un marco referencial en la evaluación de las competencias claves del supervisor de seguridad.

Oct 1, 2013

By P. Marinos, G. Tsiambaos, H. Saroglou

The anisotropic behaviour of “Athens Schist” has been brought out through the testing of specimens with varying orientation of schistosity with respect to the major principal stress under uniaxial, triaxial and dynamic conditions. A large number of results from tests on intact rock specimens of the “Athens Schist” were statistically analysed and evaluated. Le comportement anisotropique des roches du système “Schistes d’ Athènes” a été déterminé sur des épreuves avec une orientation différente de la schistosité par rapport à l’axe de chargement sous des conditions axiales, triaxiales et dynamiques. Un grand nombre des résultats a été statistiquement analysé et discuté. Zur Bestimmung der anisotropen Eigenschaften der Athen Schiefer wurden einaxialen, dreiaxialen und dynamischen Kompressionsversuchen an Gesteinskernen durchgeführt, bei denen die Belastungsachse verschiedenen Neigungen gegen die Schieferung hat. Die Messreihen an anisotropen unzerreissbaren Fels Samplen von Athen Schiefer wurden statistisch analysiert.

Jan 1, 2003

By Laurence G. Trudell

A geologic framework for interpreting stratigraphic and geographic variations of the Green River Formation in the Piceance Creek Basin is developed from lithologic data accumulated by the Bureau of Mines from oil-shale coreholes. From detailed Bureau of Mines descriptions of samples from nine coreholes and supplementary lithologic data from seven additional sampled sections, three cross sections were constructed along lines transecting the basin. Plotted as lithologic columns with corresponding oil yields and resistivity logs, the sampled sections are correlated on a time-stratigraphic basis. Distribution and correlation of nahcolite and halite zones are shown, and the approximate base of leaching of these saline minerals is indicated. General lithologic characteristics of members and zones are discussed and interpreted. Large-scale lithologic logs illustrate the nine Bureau of Mines core descriptions, and the complete description of Bureau of Mines-Atomic Energy Commission Colorado Corehole No. 1 is included in an appendix. The time-correlated cross sections provide a necessary framework for understanding the depositional history of the Green River Formation and will facilitate evaluation of oil shale and other mineral resources in the Piceance Creek Basin.

Jan 1, 1970

By Henry P. Chandler

TONNAGE of natural abrasives sold or used in the United States in 1959 increased 12 percent. Artificial abrasives produced in the United States and Canada jumped 24 percent. Imports, exports, and reexports of abrasive materials also showed gains. Sales of grinding wheels were up 33 percent and coated abrasives 17 percent. FOREIGN TRADE Imports of abrasive materials totaled $91 million, an increase of nearly 51 percent over 1958. Chief commodities contributing to [ ]

Jan 1, 1960

By Geraldo Morón

En este trabajo, Minera Aurífera Retamas S.A., Es una empresa de minería subterránea dedicada a la exploración, explotación, beneficio y comercialización de oro. Dentro de su política organizacional viene asignando recursos y orientando esfuerzos en la gestión ambiental para calcular, reducir y compensar la Huella de Carbono producto de su actividad minera desarrollada en su Unidad Económica Administrativa Retamas, (UEA Retamas), la cual geográficamente se ubicada al norte del territorio peruano y políticamente en el distrito de Parcoy, departamento de La Libertad. La gestión ambiental adoptada por MARSA en su UEA Retamas radica en tres etapas principales; Calcular, Reducir y Compensar la Huella de Carbono.

Sep 1, 2017

By P. H. Oliver

"The current theory of how explosives fracture rock offers no explanation for the improvements in fragmentation and the reduction of fly rock and back break which occurs when an adequate inter-row delay time is used. Nor does it explain why fragmentation improves with rectangular drill patterns where the hole spacing may be as much as four times the hole burden.A new theory of rock fragmentation is proposed which builds on the existing theory. It offers rational explanations for the many blast effects which the current theory does not address and the need for adequate timing delays between rows. It improves on the design of inter-row delay timing by defining the length of free-blasted face needed in front of a hole *Retired from Inco Ltd., Sudbury, Ontario when selecting the delay element which will provide an adequate inter-row delay time."

Jan 1, 2003

By P. H. Oliver

The current theory of how explosives fracture rock offers no explanation for the improvements in fragmentation and the reduction of fly rock and back break which occurs when an adequate inter-row delay time is used. Nor does it explain why fragmentation improves with rectangular drill patterns where the hole spacing may be as much as four times the hole burden. A new theory of rock fragmentation is proposed which builds on the existing theory. It offers rational explanations for the many blast effects which the current theory does not address and the need for adequate timing delays between rows. It improves on the design of inter-row delay timing by defining the length of free-blasted face needed in front of a hole when selecting the delay element which will provide an adequate inter-row delay time.

May 1, 2003

"These guidelines, implemented in 2003, were recommended by the Diamond Exploration Best Practices Committee established by the Canadian Institute of Mining, Metallurgy and Petroleum. The guidelines are applicable to public companies and their consultants reporting diamond exploration results.“The guidelines are referenced in the Companion Policy of NI 43-101 with a statement that disclosure regarding the reporting of diamond exploration sampling results should conform to them.”Reporting GuidelinesThe following guidelines have been recommended by the Diamond Exploration Best Practices Committee established by the Canadian Institute of Mining, Metallurgy and Petroleum. These guidelines are applicable to public companies and their consultants reporting diamond exploration results.In respect of these guidelines, Diamond Exploration Results are results derived from the initial activities undertaken to investigate a diamond bearing prospect or deposit, to generate tonnage, grade and value estimates that cannot be classified as a Mineral Resource or Mineral Reserve. They do not address the earlier stage reporting of geophysical, geochemical or kimberlite indicator mineral results.Public reports of Diamond Exploration Results relating to mineralization not classified as Mineral Resource or Mineral Reserve must address the confidence limits of the result and contain sufficient information to allow a considered and balanced judgement of the significance of the results.The objective of these guidelines is to assist public companies and consultants in making appropriate disclosure of diamond exploration results by reporting in a manner which is:Uniform within the diamond exploration industry; Consistent with reporting from other industry sectors .Comprehensive .Unambiguous .The guidelines are not prescriptive. Materiality is the overriding principle that determines the information that should be disclosed. However, where a company or consultant deviates from the guidelines, the disclosure or technical report should state the extent to which the guidelines have not been followed, and the reasons for the deviation.The guidelines do not in any way replace jurisdictional reporting requirements (For example, the requirement for Canadian reporting issuers to comply with Canadian Securities Administrators National Instrument 43-101 by having technical disclosure endorsed by a Qualified Person as defined in that legislation)."

Jan 1, 2003

By Gordon Clark, Basar Arioglu, Nasri Munfah, Sanja Zlatanic, Tolga Togan

"The 13.2 m (43 ft) external diameter, double deck Istanbul Strait Road Tube Crossing is one of the most challenging underwater tunnel projects in the world. Subjected to 11 bars of hydrostatic pressure, variable geology, and being in a very active seismic area, the execution of the project required innovative solutions, sophisticated construction techniques and prudent risk management approach. The 5 km (3.1 mile) tunnel consists of a 3.4-km (2.2-mile) tunnel boring machine- (TBM) bored tunnel, 1 km (0.62 mile) twin NATM tunnels and cut-and-cover sections. The project is being delivered in a build-operate-transfer (BOT) contract in a public-private partnership. The technical challenges, coupled with financial and commercial risks required the implementation of sophisticated risk management tactics including the provision of independent design verification. The project was opened to traffic on December 20, 2016, four months ahead of schedule.. This article presents the technical challenges of the project from the design, construction, and risk management aspects..Project backgroundThe $1.245 billion Istanbul Strait Road Tunnel Crossing project, dubbed the Eurasia Tunnel, is one of several major infrastructure projects being implemented in the Republic of Turkey in a public-private partnership approach. The project provides a direct and easy connection between the Anatolian (Asian) side of Istanbul and the heart of its historical district on the European side across the Bosphorus Strait which connects the Black Sea with the Sea of Marmara. The project improves connections to a wide network of motorways on both sides, increase capacity across the Bosphorus by 100,000 vehicles a day, reduces congestion and saves motorists an average of 45 minutes of commuting time in each direction bringing significant economic benefits to the city and the region. It eases traffic across the strait, reduces congestion, decreases pollutants and emission while maintaining Bosphorus. It is the most complex part of the project with the greatest challenges and risks. Part 2 is 5.4 km (3.6 miles) long consisting of 3.4 km (2.2 miles) of 13.2 m ( 43.3 ft) external diameter TBM bored tunnel under the Bosphorus Strait, 1-km (0.62-miles) of twin NATM tunnels on the Asian side, cut-and-cover transition boxes in the Asian and the European sides and depressed approaches on both sides. In addition, this segment includes the toll plazas, ventilation buildings, and the tunnel control and maintenance facilities."

Mar 1, 2017

By Jose Carlos D'Abreu, Edelink Efrain Tinoco Falero, Mauricio Marcos Otaviano

The production and consumption of Direct Reduced Iron (DRI) are continuously increasing, as a consequence of the impact of shale gas extraction technology on the Natural Gas (NG) market. Considering this context, DRI may improve the Blast Furnace (BF), Electric arc Furnace (EAF) and LD converter ’s productivities and consequently their competitiveness. In this work the results of a cooperative research conducted by PUC-Rio University and a Brazilian mining company are presented. Laboratory-scale simulation tests, using DR commercial pellets and typical industrial operational parameters of a benchmarked DR shaft furnace, were conducted and planned using statistical and factorial analysis. In the simulated experiments, the following three regions of the DR shaft furnace were considered: Reduction Zone (RZ), Transition Zone (TZ) and Cooling Zone (CZ). Three stages were considered in the research development: (i) the reactions and equations concerning pellet metallization and Carbon precipitation were analyzed; (ii) experiments focused on the de finition of the carburization kinetic equations occurring in the Transition and Cooling zones, and finally, (iii) aimed to develop the “METCARB” model, a computational program conceived to simulate mathe- matically the metallization and carbonization reactions along the height of the furnace. In conclusion, a comparison is made with industrial results in order to validate the resulting “METCARB” model.

Mar 1, 2018

By N. Duda, W. Koperska, S. Anufriiev, P. Stefaniak

In mineral processing plants ore extracted from mines is processed to obtain a concentrate with the highest possible concentration of this valuable product. It is a complicated multi-stage process. Usually, the first step is sieving the ore, which is typically done using vibrating mining screens. There is often only a limited number of these machines in the technological chain, which is why their continuous operation, and proper maintenance is crucial for the whole process. Predictive maintenance is the best strategy in this case because it allows for minimising the number and duration of unexpected stoppages. It consists of the prediction of future failures based on available real-time data, and predictive models built upon this data using, for example, machine learning techniques. In this paper we concentrate on feature generation for future predictive maintenance model development for a vibrating screen, based on an example of a KGHM ore processing facility in Polkowice-Sieroszowice. We focus on two types of measurements: bearings temperature and vibrational data. Based on the raw data, the process of more advanced feature engineering is described. By transforming the temperature data we calculate characteristics of bearing cooling and heating dynamics, while based on vibrational data, the aggregated characteristics of the vibrations are derived. Such features are calculated on a long-term basis, and then they are compared to the data related to vibrating screen maintenance to estimate their significance for the prediction of particular failures of the machine.

Sep 1, 2021

By E. Spencer

Overexposure to hazardous noise has been found in most mining sectors, with up to 100% of the surveyed workforce experiencing a noise dose over the Mine Safety and Health Administration (MSHA) permissible exposure level (PEL). As a result, miners show elevated rates of hearing impairment of 70-90% by retirement age. To help manage noise exposures, the National Institute for Occupational Safety and Health (NIOSH) developed the Determination of Sound Exposures (DOSES) software and implementation guide for use by mine management and safety personnel. The software relies on a time-motion study that profiles the worker?s daily activities. Observations about the worker?s location and tasks or other activities are recorded along with the start and end time, to determine the duration of the tasks, so they can later be matched up with the noise data. The software gives the user the option of assessing dose relative to the MSHA PEL, the Action Level or the NIOSH Recommended Exposure Limit. The software generates a variety of interactive onscreen displays showing where, when, and how the worker?s noise dose accumulated. It also can generate customizable printed reports. These outputs can be used to highlight the tasks, locations, and times that are associated with the greatest amount of the worker?s noise exposure. DOSES simplifies the record keeping and analysis associated with time-motion studies and worker noise exposures, so mine management can make engineering noise control or administrative control decisions to limit the noise over-exposure of their workers.

Jan 1, 2010