Search Documents

By D. J. Burkhardt

Newer copper SX/EW facilities often incorporate hot water heating for the cell feed electrolyte to obtain the necessary plating temperatures of 40 to 50°C. Heating is most necessary in oxide heap leaching, however it may also be required in bioleaching of secondary sulphides in colder climates or higher altitudes where most of the heat gain in the heap is lost to the environment. Given that the solution flows in the leach, organic circuit and electrolyte circuit are circular in nature, and the fact that the hot lean electrolyte is often exchanged with cooler rich electrolyte, it can be difficult to access the heating requirement for the cell feed. There are energy losses in piping, tankage, raffinate, and energy gains through the PLS and electrowinning process itself; some of these are significant and others are not. This paper discusses the overall heat balance, the relative significance of the various energy gains and losses, and describes a methodology to develop a heat balance to assist the engineer in sizing the heating equipment.

Jan 1, 2003

By Bryn Harris

Much has been written over the past twenty years on the removal and chemical stabilization of arsenic from metallurgical process solutions. This paper reviews again the latest developments in this field, and concludes as before that the high-iron arsenical ferrihydrites, together with the high temperature arsenic minerals, scorodite and Type II, remain as the best and most viable vehicles for industrial control and disposal. However, a cautionary note is introduced, in that chemical environments cannot be considered in isolation, and that cogniscence has to be taken of microbiological activity in determining the disposal method. Data are also presented on a survey of industrial practice, which shows that arsenical ferrihydrite is by far the most widely-practiced and accepted method used worldwide. Finally, the disaster in Bangladesh is briefly discussed with reference to lessons that the metallurgical community might learn from this.

Jan 1, 2003

By Ali Akbar Mottahedi

It is known for a long time that the reaction of oxygen with carbon, silicon, iron and many other elements is exothermic. The heat of released from these kind of reactions can decrease the time of fusion of iron and steel for metallurgical purposes in the electrical arc furnaces. By decreasing the time of fusion, we increase the rate of process and the amount of production. So, by blowing oxygen in to the furnace, we can reduce the consumption of electricity and save cost. There are many problems in the procedure of the oxygen blowing. In this project, the theoretical aspect of the oxygen blowing and its side effects into the arc electric furnaces are investigated. An oxygen blowing system into the arc electrical furnace of metallurgy department of Machine Sazi factory was also set up. This process reduced the consumption of electricity up to 22% and increases the rate of production, by reducing tap ? to ? tap time up to 15%. In this project; all oxygen blowing systems and its control were set up.

Jan 1, 2006

By J. Riccardi

Copper refineries use massive copper castings as moulds into which impure molten copper from the reverberatory furnace is poured to form anodes for further electrolytic refining. To facilitate removal of the copper anodes from the mould and to prolong the life of the mould itself, it is traditional to spray the mould surface prior to each use with a slurry of baryte in water. This slurry application leads to poor housekeeping, operating costs are escalated by the cost of the slurry, and additional problems in the subsequent refining process are experienced due to carry-over of excess undesirable baryte powder. A one-time application of a diffused layer of aluminum to the surface of the copper mould prior to putting the mould into service has been found to provide extended mould life and facilitate anode removal, as well as reducing baryte consumption; thereby reducing operating costs at both the anode manufacturing and refining stages.

Jan 1, 1999

By Javier Antoñanzas, Juan Carlos Múgica, Lourdes Yurramendi

The gasification of wastes containing an organic fraction is usually performed at low-medium temperature using different kind of catalysts. The off gas obtained is a mixture of carbon oxides, mainly carbon monoxide, and hydrogen and can be used for different energetic applications. The main problem is the production of tars in the off gas that has to be separated from the valuable gas flow and, finally, treated separately. An interesting alternative is the partial or total treatment of organics at high temperature. In this case, the off gas contains a higher content of hydrogen and elemental carbon as particulate matter. The energetic source to obtain a temperature in the range of 1,000 - 1,200 ºC is obtained by a plasma torch. In order to make de process attractive, an important issue to be considered is to commercialize the carbon obtained for different industrial applications.

Jan 1, 2008

By Tian Li

Molecular crystal growth during gibbsite precipitation from caustic aluminate solutions under different flow regimes was investigated in three different laboratory precipitators. The gibbsite precipitation experiments were conducted at the same temperature, initial liquor composition and seed type. The Taylor-Couette precipitator and the stirred tank precipitator were operated, respectively, under the laminar and turbulent flow regimes, while the bottle roller precipitator was operated in a complex flow regime, where fluid flows are generated by the end-over-end rotation of the bottles. Comparison of the growth rate estimates from the different flow regimes showed good agreement, which suggests that the hydrodynamic regime has little or no effect on gibbsite crystal growth under the operating conditions employed in this work. The growth rate estimates from the current precipitation study showed a second order dependency on supersaturation and is consistent with a screw dislocation growth mechanism. The findings of the current work are in agreement with previous gibbsite crystal growth studies published in the literature.

Jan 1, 2003

By Byung-Su Kim

Most electric arc furnace dust (EAFD) treatment processes employ carbon as a reducing agent for the zinc oxide in the EAFD. In the present work, the reduction reaction of zinc oxide with carbon in the present of various additives was studied. The effects of temperature and the additives of calcium carbonate, magnetite, and mill scale on the kinetics of the reduction reaction were measured in the temperature range of 1173 K - 1373 K under nitrogen atmosphere using a weight-loss technique. The mill scale is one of byproducts generated from the steel rolling process. From the experimental results, it was concluded that all three additives accelerates the reaction rate of zinc oxide with carbon, but the effect of addition of calcium carbonate is the highest. It was also found that magnetite, mill scale, and calcium carbonate in the reduction reaction of zinc oxide with carbon promotes the carbon gasification reaction.

Jan 1, 2006

By William Ewing

Copper is rapidly being adopted by the semiconductor industry as the interconnect material of choice. The aqueous processing techniques used generate wastes such as spent electrolyte from electroplating, electroplating rinse water, copper solutions from removing copper from the back of the wafer and CMP waste streams. We are examining the use of chelating resins as a means of recovering copper from these streams within the processing plant, thereby allowing recycling of process water and minimizing hazardous waste disposal costs. We have examined the effect of model plating additives (and other organic complexing agents) on the efficacy of Dowex M4195. Although these might have had a significant effect, commonly used electroplating additives polyethylene glycol (PEG), benzotriazole (BTA), thiourea, glycine, and 3-mercapto-1-propanesulfonate (MPSA) each had little or no effect on the ability of the resin to chelate copper and remove it from solution. This suggests that Dowex M4195 could be useful for treating waste solutions of rather variable compositions.

Jan 1, 2003

By Michael L. Sorokin

The metallic nickel production by converting of nickel matte is analysed from the thermodynamic point of view using earlier developed thermodynamic models for sulphide, metal and slag phase. Three-suffix Margules equations are used to calculate thermodynamic properties of melts. Potential diagrams of Ni-FeS-OSiO2 system are calculated for various temperatures and Fe to Ni ratios. The diagrams used for consideration about possibilities of the direct one-stage metallic nickel production.

Jan 1, 1995

By Nelson Collao I.

Loss of the organic phase from solvent extraction circuits is a major cost factor for SXEW operations. Recognized sources of loss include evaporation, entrainment, and biological degradation. The mechanisms for both entrainment and evaporative losses are well recognized. Biological degradation of the organic has not been as extensively evaluated as the other mechanisms but is a major source of loss. This paper discusses the impact of biological degradation on an operating plant, potential mechanisms for degradation, conditions under which biodegradation of plant organic can occur and plant conditions that may assist in promoting biodegradation.

Jan 1, 2003

By Lætitia H. Delmau

SXFIT is the latest in a series of programs developed in our group to model solvent extraction systems of increasing complexity. SXFIT permits the user complete freedom to define the constituents from which the composition of each phase is to be specified in the data and from which all species of a model for a system are assumed to be formed. Activity coefficients in the nonaqueous and aqueous phases, water activity, apparent molar volumes of aqueous species, and solution density needed for the conversion of concentration from the molarity to the molarity scale are all taken into account by the program. Several extraction systems relevant to nuclear-waste treatment were modeled successfully using this program. As an example, the cesium extraction efficiency of the CSSX process chosen by the USDOE for cesium removal from high-level waste stored at the Savannah River Site can be predicted correctly for varying feed composition.

Jan 1, 2003

By P. J. Moor

Britannia Refined Metals Ltd. was built in 1931 to refine the lead bullion produced at the Mt. Isa mine in Queensland, Australia. Several periods of expansion and development have taken place over the intervening years, leading to major increases in the refining capacity for both lead and silver. A plant for treating recycled lead-acid batteries was added in 1976. This was redeveloped in the early 1990's to utilise Isasmelt technology for the smelting operations. Most recently the No. 2 refinery kettle floor was extended to enable it to process lead bullion produced from two Imperial Smelting Furnaces (ISF), at Britannia Zinc Ltd. in Avonmouth, England and at MIM Hüttenwerke in Duisburg, Germany. This expansion included the provision of a plant for the hygienic handling of drosses and skims. This paper briefly describes the present primary refining operations and gives an update on the most recent developments in the process metallurgy and operating practices that have taken place.

Jan 1, 2000

By Frédéric Pineau, Guillaume D'Amours

Semisolid metal processing of metallic alloys takes advantage of the thixotropic behavior of material with non-dendritic microstructure to produce near-net-shape components with improved mechanical properties. The much higher apparent viscosity of the semisolid billet limits the risk of oxide formed on the free surfaces to become incorporated into the easting during the process. But, the external-skin on the periphery of the billet, which is often partially solidified and contaminated with lubricants, should not be included into the casting as this can be a cause of reject for most structural parts. In this paper, a preliminary model is set-up using the LS-DYNA SPH formulation to follow the paths of the skin. Calculations carried out show that this approach appears to be very promising to predict the paths of contaminated skins into semisolid castings. It can then be utilized to design suitable molds and gating systems.

Jan 1, 2012

By Guo Xueyi

The reaction mechanism for the manganese dioxide reductive dissolution in acidic chloride media in the presence of ferrous/ferric ions are based on theoretical delineation and dual cell experiments. In terms of the Buttler-Volmer equation and chemical kinetic principles, a electrochemical kinetic equation was deduced, which successfully provided a theoretical basis for describing the role of Cl-, Fe2+, Fe3+ and H+ in solution, as well as their interrelationship in manganese dioxide reductive dissolution. Dual cell experimental studies indicate that the increases of Cl- and Fe2 in solution are helpful to accelerate the couple process; while, Fe3and Mn2+ hinder the coupled reaction to some degree. Higher acidity in solution is beneficial to the dissolution of MnO2. All the dual cell experimental results are consistent with the theoretical deduction. This study will be useful to understand the mechanism for the leaching of manganese nodules from the deep ocean, as well as the leaching of manganese dioxide ore from land.

Jan 1, 2003

By Lary L. Speakman

Typical heavy metal removal system generate a great deal of waste that must then be discharged somewhere. Using Bio-Fix Beads developed by the Bureau of Mines in combination with other waste stream minimization processes, Harrison Western Environmental Services has developed a "zero" discharge operation. Data from current on-site operations will demonstrate the effectiveness of the Harrison Western approach. For 1992 Annual TMS meeting,: "Future Trends and Innovations" Material category Key words: Residues and Effluents Technical category Key words: Extraction and Processing.

Jan 1, 1992

By J. A. Voigt

In an effort to determine the optimum conditions for preparing high purity, fine particle size high temperature superconducting oxide powder, we have investigated how calcination conditions influence the conversion of a chemically prepared hydroxycarbonate precursor powder to YBa2Cu307. We find that the precursor can be converted to phase pure YBa2Cu307 in either oxygen or synthetic air (20% 02. 80% N2) at 850°C. This temperature is substantially lower than the temperature (>900°C) normally used for the calcination of mixed-oxide powders. The lower calcination temperature prevents particle sintering and maintains the desired fine particle size. Powder processed in synthetic air shows a low degree of crystallinity indicating it may be more sinterable than the highly crystalline powders produced when an oxygen atmosphere is used. Intimate contact between powder particle surfaces and a flowing gas atmosphere promotes the reaction between the BaCO3 component of the precursor powder and the Y and Cu constituents.

Jan 1, 1989

By Marco Pasetto

The possibility to re-use marginal materials (by-products) deriving from industrial activities in the construction of road infrastructures, as total or partial substitution of natural aggregates, successfully combines demands for economy and environmental sustainability. The paper presents the results of a laboratory study, conducted at the Experimental Road Laboratory of the University of Padova, to verify the suitability of a particular type of electric arc furnace slag to be recycled in the lithic skeleton of high-performance asphalt mixes (porous asphalt, high modulus mixes, stone mastic asphalt, nonskid surfacings) for road and airport flexible pavements. the process of transformation of iron and steel slag into a product that can be used in road building is described, along with the characterisation of the mixtures, plus an analysis of the results of a wide battery of mechanical-performance tests. This study forms part of wider theoretical ? experimental research being done at the University of Padova in order to improve knowledge of the characteristics of succedaneum materials and check their possible applications in road and airport construction.

Jan 1, 2006

By Andrew A. Fyfe

The start-up and operating results obtained at Zia Technology Inc.'s first commercial operating facility at Caldwell, Texas are described. The operation which stated in early 1991 is the first to employ the patented Inclined Rotary Reduction System (IRRS') with the associated 'all-metallic retort for the recovery of all metallics contained in EAF dust.

Jan 1, 1992

By V. L. Stolyarova

The high-temperature Knudsen effusion method was used to study partial pressures of vapour species, activities of components and the Gibbs free energies in the DyF3-Dy2O3 system at the temperature (1357±5) K. Partial pressures of vapour species were obtained by the ion current comparison method, with the DyF3 partial vapour pressure over pure DyF3 as a standard. The equilibrium constant of the gaseous reaction DyF3 + DyOF = Dy2OF4 is evaluated. Thermodynamic data obtained are in a agreement with the available phase diagram of the DyF3-Dy2O3 system. Results of the present study illustrate the negative deviations from the ideal behaviour in the system.

Jan 1, 1997

By Larry Southwick

This paper covers technical and other developments during the first 20 years of Peirce-Smith converting. There were numerous mechanical and process ideas and concepts already being developed and used by others that had possible application within the converter that Peirce and Smith were moving ahead with. There were also other converter configurations in which the basic lining and larger size concepts could function. Finally, as awards and honors began to accumulate, there were those who felt that contributions of other early workers were being ignored. The working out of these conflicts and differing directions will be described.

Jan 1, 2009