Search Documents

By Hiroaki Nakano, Kenji Hara, Shunsuke Kawano, Takeshi Ohgai, Michiaki Ikeda, Hisaaki Fukushima, Shinji Yamashita, Tetsuya Akiyama, Hisayuki Kaku

"Ni-Fe alloys have an inverse magnetostrictive effect (Villari effect) in which its permeability varies according to the ·applied strain. This alloy film has a potential for application as force sensors such as torque sensors, tension sensors and so on. Electrodeposition is promising as a technique for preparing Ni-Fe alloy film because of its convenience and economy. In this paper, the effects of electrolysis conditions on the magnetic properties of electrodeposited Ni-Fe alloy films were investigated. Hysteresis loops of Ni-Fe alloy films on copper substrates from sulfate bath were measured by a vibrating sample magnetometer (VSM). The films of low coercivity, which were preferred when used as a force sensor were obtained by introducing certain additives to the sulfate type bath.INTRODUCTIONNi-Fe alloys show an inverse magnetostrictive effect (Villari effect) that their permeability varies depending on the applied strain. The films of this alloy have a potential for application as force sensors such as torque sensors, tension sensors and so on. The authors et al. tried to prepare Ni-Fe alloy films using the sputtering technique, and produced a prototype of Ni-Fe alloy torque sensor [I]. The sensitivity was higher in the torque sensor thus produced than the strain gauge type one, and this torque sensor enables non-contacted detection. It showed excellent durability and reliability. However, the formation of Ni-Fe alloys by sputtering requires higher costs and brought an another problem that the shape of the substrate on which the film was formed was considerably limited. This causes a hindrance to the wide-range application of the force sensors. Electrodeposition is promising as the technique for preparing Ni-Fe alloy films because of its convenience and economy. In this paper, the effects of the conditions of electrodeposition on the magnetic properties of Ni-Fe alloy films were studied."

Jan 1, 2000

By John ?gren, Martin Schwind, Henrik Larsson

"A new model for internal oxidation, as well as similar processes, has been implemented on computer. It is based upon a combination of random walk and cellular automata and is capable of treating 3-dimensional cases. To model diffusion, it utilises quantised units of matter. All steps of the process are included: nucleation, growth and coarsening. The effect of grain boundaries on diffusion as well as nucleation is taken into account. Further possible development is briefly discussed; especially the treatment of nucleation needs further consideration. IntroductionComplex diffusion-controlled processes may now be simulated on a routine basis when concentration varies along one co-ordinate only. One-dimensional simulations capture much of the information of interest but not all. For the case at hand, especially the spatial and the size distribution of precipitates, as well as the impact of grain boundaries, would be interesting information not accessible from 1-D simulationsSolving the full Fick-Onsager law in three dimensions does not seem feasible with the computers of today. In the model described in this article, random walk by quantised units of matter are considered. The model should be useful for a number of cases involving dispersed systems. With further development, it would indeed seem possible to simulate most types of phase transformations.Previous workWe have previously published two articles [1,2] on the new approach discussed in this work. In those articles we described the basic idea and showed, among other things, that very good agreement with an experimental concentration profile can be obtained, in a single-phase system, using independently assessed thermodynamic and kinetic data. Also, Schwind used the same random walk based concept to model coarsening [3]."

Jan 1, 2001

By Angus Hellawell

The application of the common tangent principle to free energy - composition surfaces is considered. It is shown that the construction requires that single phase surfaces on either side of a two phase volume must always exhibit the same sign of curvature - contrary to that shown in many published phase diagrams. In general, these curvatures will be such that the surfaces are mutually concave towards the more stable phase. A number of examples are discussed.

Jan 1, 1991

By Chang-Young Choi

Korea Zinc commenced zinc production in 1978 with a capacity of 50,000 tpa. Since then, continuous investments have been made and resulted in Korea Zinc now being the biggest zinc and lead producer in the world. In the course of increasing zinc production capacity, the company management realized that the company needed a lead smelter to prevent the solid waste disposal problems by treating the lead containing solid waste. This paper begins by briefly stating the objectives and the roles of the lead smelter at Onsan. It describes the QSL process and the TSL process, and further extends the description of the TSL process, through which harmless inert solid waste could be produced for secure final disposal. It is also mentioned that the TSL process plays an important role in the integration of zinc and lead production. Throughout the paper, a positive attitude in handling the environmental issues in the non-ferrous smelting industry is emphasized. Finally, a solution for the solid waste disposal problem in the zinc and lead industry is proposed, with which the environmental issues can be an opportunity rather than a crisis. The current operation at Onsan suggests the future direction of the non-ferrous smelting technology that all of the zinc and lead producers should pursue.

Jan 1, 2003

By T. Nakamura

TiO2 and Ti/TiO2 thin films were deposited on a quartz substrate by laser ablation of TiO2 and Ti targets using Nd:YAG pulsed laser. After sulfurization of the TiO2 film in H2S or CS2 gas at 1273 K for I hour, the surface atomic structure was changed. Furthermore, the Tirri02 film was successfully prepared by the subsequent ablation of Ti and Ti02 targets. The morphology and structure of the films were characterized by XRD, XPS and AFM analyses.

Jan 1, 2003

By Donald J. Hallbom

Limonitic nickel laterites slurries exhibit complex rheological properties including time dependency that varies from thixotropy to rheopexy. Chronic problems may occur if plant designers and operators fail to take time dependency into account. Stress decay tests indicate that laterite slurry takes roughly two minutes to approach steady state after a step change in the shear rate. As a result, most rheometer measurements are taken at a non-equilibrium state, making evaluation difficult. Two minutes is also long relative to the time that a unit of slurry in a processing plant is at any given shear state, so the slurry may never reach equilibrium. This paper presents a method to describe the rheology of laterite slurry using a Flow Array, which describes the rheology using an array of instantaneous flow curves crossed by an equilibrium flow curve. A rate equation for structural change in non-equilibrium conditions allows time dependence to be efficiently modeled. This flow array allows the flow behavior of time- dependent slurry to be predicted in non-equilibrium conditions using a simple time-step methodology. Keywords: Rheology. nickel laterite, hydraulic transport, pressure acid leach, flow array

Jan 1, 2004

By Baokuan Li, Qiang Wang, Zhu He

"A mathematical model has been developed to investigate the magnetohydrodynamic (MHD), thermal, and solidified behavior in electroslag remelting process. Based on the finite volume method, a multiphase coupling MHD approach is employed to investigate the droplet formation as well as movement in molten slag under the action of an alternating current. The VOF formulation is adopted for interface tracking. The electrical potential method is adopted for the electric current and magnetic field. The Electromagnetic force and Joule heating are recalculated at each time step and then is implemented in the momentum and energy equations as a source term, respectively. Moreover, solidification of the metal is described by an enthalpy-based formulation, while the mushy zone is treated as a porous medium with porosity equal to the liquid fraction. The model is used to investigate the effect of electrode tip shape on MHD, thermal, and solidified behavior and provide valuable information.IntroductionElectroslag remelting (ESR) process has been used widely to produce high-performance alloys dedicated to critical application, such as hot work tool steels, nickel base alloys, the manufacture of components in aerospace and landbased turbines, etc. Figure 1 shows a schematic diagram of ESR process including a consumable electrode, a molten slag pool, a liquid metal pool, a solidified ingot, and a water-cooled mold. Alternating or direct current flows from the electrode to the water-cooled baseplate through the high resistivity calcium-fluoride-based molten slag which result in Joule heating and Electromagnetic force (EMF). Part of the Joule heating melts the electrode and the droplets travel through the slag and accumulate the liquid metal pool. The electrode is continuously advanced into the slag as it melts to build up an ingot of improved structure and composition by controlled solidification and chemical refinement. The metallurgical properties of the remelted ingot are really related to the solidification structure, which strongly depends on magnetohydrodynamic, thermal, and solidified behavior in the molten slag, liquid metal pool, and mushy zone."

Jan 1, 2014

By S. Jolivet, A. Klöfverskjöld, P. Latostenmaa, B. P. Wilson, M. Lundström, P. Halli

Doré slag is secondary product of copper electrore fining anode slime treatment. The slag consists mainly of different slag formers, such as borax and silica based minerals together with soda and traces of sealing materials. However, Doré slag also contains metals present in the anode slime, such as Ag, Cu, Bi, Sb and Te. At some plants, slag cleaning has been conducted utilizing conventional grinding and flotation circuits in order to enrich the content of precious metals in the slag [1]. Nevertheless, the routine consideration of the slag as a secondary raw material has so far not been adopted on an industrial scale. The current study presents the preliminary results of the nitric acid and chloride leaching of antimony from Doré slag. Chemical and mineralogical analyses (SEM-EDS, AAS, XRD) were performed for the raw material, leaching residue, and leaching solution in order to ascertain the metal recovery and kinetics during leaching.

Mar 1, 2017

By Elliot Schwartz, Julian Szekely

"In this paper we describe an experiment that was recently performed on the IML-2 Space Shuttle mission in which the thermophysical properties of molten metals were measured using electromagnetic levitation. In the planning of these experiments calculations had to be performed to predict the levitation and stirring forces, heating rates, sample deformation, and internal flows within the sample. These predictive calculations were essential for both the planning of the experiments and for the re-planning of experimental runs during the actual Space Shuttle mission.Introduction""Materials Processing in the Computer Age"" involves the use of mathematical modeling to obtain a quantitative understanding of the phenomena that govern materials processing operations. Microgravity, or space shuttle experimentation represents a specific case in point here; the very high cost of the space shuttle flights, the very limited flight opportunities that are available, and the tight resources aboard a shuttle clearly mandate that these experiments be very precisely planned and that all possible opportunities for mathematical modeling be fully exploited.The purpose of this paper is to present the results of calculations performed for the planning of a space shuttle experiment involving electromagnetic levitation and wherever possible present a comparison of the computational predictions with both experimental measurements and asymptotic analyses. Finally we shall seek to discuss the practical implications of both the computational methodologies and the potential experimental findings."

Jan 1, 1994

By Junji Shibata

Extraction behavior of Ti(IV) and other metal ions, such as Fe(III), Fe(II), Cu(II), Zn(I1) and Co(I1) from acidic solutions like sulphuric acid and hydrochloric acid was studied in order to recover titanium from the waste solution in Ti02 production. Extractant used was tri-alkyl phosphine oxide whose trade name was Cyanex 923. Then, a study was made of the idea of simulating a countercurrent multistage extraction system, using the results of batch extraction. The simulation was camed out on extraction and saipping behavior for a Ti(1V)-H$O,-Cyanex 923 system. From the simulation result., the optimum operating condition of the system was considered.

Jan 1, 1994

By F. J. Tavera

Recently Jameson cell technology has gained acceptance in both mineral and non-mineral applications, mainly because of the high degree of contact between the involved phases in the downcomer, fact that leads to an efficient collection performance. The key for an acceptable performance of the downcomer operation depends on the stability of the jet zone, the mixing zone, and the plug flow zone. in this work the behaviour of the downcomer of a laboratory Jameson cell is reported, as a function of gas hold-up, superficial gas velocity, superficial liquid (or slurry) velocity, and length of the operating zones. The presence of carbon is evaluated in terms of its effect on the gas hold-up and bubble surface area flux. The influence of the downcomer operating conditions on the gas-liquid disengaging cell is presented. Keywords: Jameson cell, downcomer, gas hold-up, mixing, plug flow, conductivity.

Jan 1, 2003

By Saskia Duyvesteyn

Ion flotation is a technique applicable to the removal of metal ions from dilute solutions, using ionic surfactants.- While there are a number of physical and chemical parameters that influence the ion flotation process, this paper focuses on two of the important chemical ones, namely frother concentration and ionic strength. The effect of several frothers, including ethanol, iso-propanol and MIBC at concentrations ranging from 0% to 0.4%, was studied for the model Cd-dodecylsulfate and Cu-dodecylsulfate systems. The ionic strength, as well as the effect of monovalent and multivalent counter ions, was also studied in the range of 1@3 - 1 M, at constant pH. The results are discussed in terms of applicability to a range of effluents from minerals and materials processing operations.

Jan 1, 1994

By Giulio R. Altoé, Sergio N. Monteiro, Ygor M. Moraes, Rômulo L. Loyola, Frederico M. Margem, Gabriel O. Glória

The tensile properties of DGEBA/TETA epoxy matrix composites reinforced with different amounts of PALF fibers were evaluated. Composites reinforced with up to 30% in volume of long, continuous and aligned PALF fibers were tested in an Instron machine at room temperature. The fracture was analyzed by SEM. This one revealed a weak fiber/matrix interface, which could be responsible for the performance of some properties. The results showed significant changes in the mechanical properties with the amount of PALF fibers.

Jan 1, 2015

By Jimsher Aneli

The investigation of some peculiarities of conductivity dependence on filler type and amount in the polymer composites has been conducted. It is established, that conductivity of composites based on phenolformaldehide resin essentially depends on proportion of double fillers: graphite + carbon black, graphite+ andesite, contained in composites. It was shown, that these composites characterized by synergetic effect ? non additive influence of fillers concentration on the conductivity of composites. Some other properties of composites contained binary fillers (effect of temperature and pressure on the conductivity) have been investigated.

Jan 1, 2006

By Shigehisa Endoh, Hitoshi Ohya, Atsushi Inaba, Shigeki Koyanaka

"Recycling should be promoted to keep the global environment. However, it is difficult to detennine the quantitative impact. A life cycle assessment is one of the most reliable methods to estimate the global environment impact.Exergy is useful like entropy when considering the sustainable development. All of our activities have been obtained exergy resources and/or energy itself and throw away waste and/or waste heat. We are trying to use exergy to estimate the quantity of energy and matter for resource accounting. For recycling plastic, plastic has two aspects; material and energy source.The environmental assessment of plastic recycling suggests that the exergy reduction of the entire system is estimated by the yield of matter and the process efficiency. The material recycling is better than the thennal recycling when the process efficiency is high. However, the thennal recycling is much better for the low efficiency. The transition point is able to be decided by the efficiency of the manufacturing and the electric power generation.IntroductionRecently, many of the global environmental problems have become conspicuous like global wanning, ozone layer depletion and acid rain. Some of the methods like life cycle assessment for solving these problems have been presented. Anxiety concerning the proble1ns of energy and resources has led to a rapid increase in the interest in describing and understanding the conversion processes of energy and other resources in today's society. All human activity is supported by obtaining power and products of high exergy from the environment and throwing away the waste material and the waste heat of low exergy back the environment. However, the total exergy in the whole system becomes absolutely smaller than before.The rate of obtaining high exergy products and energy itself by human activity and the speed, by which waste and waste heat having low exergy are thrown away are too fast to attribute to environmental problems [1-3].A material's use by recycling was often common in a circulating society mainly. A significant amount of energy is consumed during circulation. An environmental impact assessment method for the process or the system has not been devised when both of them are taken into consideration. Even if the life cycle assessment evaluation, which has been correctly used up to now, is applied, it is not sufficient for an overall evaluation concerning matter and energy.The real sustainable development is that the exergy reduction value by all human activities on the earth is kept within the range of the exergy reduction in order to consider the earth as closed stationary system. It is important to evaluate the process or the system by using the exergy, and design them so that the exergy loss may decrease as much as possible. We have to consider what process improvement is the most effective."

Jan 1, 2000

By K. Noda

Tamano Smelter of Hibi Kyodo Smelting Co., Ltd. started its operation adopting the Flash Smelting Furnace with Furnace Electrodes (FSFE). Thereafter, it developed a coke combustion technology based on C() concentration control, which made possible a low cost and high productivity operation without using electrodes. However, increase of treated concentrates and upgrading of matte grade for production expansion started to cause difficulties in operation control with then existing operation control system. This paper outlines recent improvements for stable operation of the Tamano Type Flash Smelting Furnace (T-FSF), such as computer aided operation guide system.

Jan 1, 2001

By Du Sichen

The present paper presents the modeling of gas-solid reactions in the case of the decomposition of CaCO3, describing the reaction kinetics on the basis of heat-transfer concepts which could be compared with thermogravimetric results. In the case of solid-solid reactions, the present paper describes the model developed for describing solid-solid reactions from dynamic X-ray diffraction technique, developed by the present team. The model has been successful in explaining the formation of spinel from MgO and Al2O3.

Jan 1, 2006

By Mehdi Asgharifar, Rouzbeh Sarrafi, Radovan Kovacevic

"The surface treatment of aluminum alloys using atmospheric-pressure of low intensity DC plasma arc discharge is investigated in terms of surface properties. With respect to the conventional surface treatment processes for aluminum alloys mostly based on chemical etching or sand blasting, this process is very environmentally friendly and cost-effective. The effect of two processing parameters, the current and the plasma torch scanning speed, on the surface morphology is studied by using a scanning electron microscope. The effects of cathode spots within the tested range of process parameters are determined, and the limiting factors of the process (such as surface cracking) are discussed. The topographical studies of the treated surfaces have suggested potential enhancement of surface properties for different applications, such as preparing surface for painting and adhesive bonding.IntroductionIn the last decade the aluminum alloys are finding broad applications in automotive industry. In order to successfully execute the joining process of aluminum alloys such as arc welding, laser welding, and adhesive bonding, there is a need to remove oxides for welding and texture the surface for bonding along the join line. A number of surface treatment techniques such as chemical etching, sand blasting, and plasma treatment have been used by industry. It is shown [1] that plasma surface treatment is characterized as environmentally friendly, lower cost, and easier to control process. Bogaerts et al. [1] mention that when an adequately high potential difference is applied between cathode and anode, electrons are accelerated toward anode by an electric field coming in collision with gas atoms. The gas breaks down into positive ions and electrons, giving rise to gas discharge. The DC electrical discharges used in industrial plasma sources can be related to their location on the voltage-current curve as shown in Figure 1.It is generally believed that dark discharges other than coronas, and arc or torch plasmas are not very good candidates for surface treatment because oflow or high power density and active species flux. However, the glow discharge plasma is used for plasma surface treatment applications because of its proper power density and active-species flux [2]. Our objective is to investigate the feasibility of using low intensity DC plasma arc discharge as a surface treatment method without damaging the cathodic non-thermionic workpiece."

Jan 1, 2011

By Andrew L. Puwis

Methodologies were presented for computing the thermal gradient associated with single crystal solidification in macroscopic computer modeling. The. heat transfer, and solidification of a shaped investment casting model were simulated using properties from three different alloys. Following the simulation of solidification, the resultant thermal gradients (G) and rates of solidification (R) from representative points were extracted in various ways and compared: It was discovered that alloy properties have a strong influence on the computed thermal gradient and rate of solidification for the three methods investigated. Data also showed that the computed gradient for each model was very different depending on the temperature range used to compute these values.

Jan 1, 1994

By John J. Dunkley

Recent years have seen the increased use of hydrometallurgy in the smelting and refining of metals. However this is often used as a final refining step, following an initial pyrometallurgical smelting process. Huge amounts of material are produced as melts which have to be cast, comminuted, and taken up into solution or leached. A common method is to granulate the melt and then grind it. In the case of metallic melts this can be difficult or unfeasible due to the ductility of the granulated particles. Water atomisation is capable of replacing the granulation and grinding stages with a single process step that can process in excess of 30t/hour of melt into particles as fine as 50 microns. Applications in operation in Co, Cu, Ni, Ag, Au, Pt and Rh refining are discussed together with potential applications in copper smelting.

Jan 1, 2003