Search Documents

By George E. Cook, Peter C. Levick, Francis M. Wells

"Relationships are established between the peak current of a pulsed, rectangular current waveform and the pulse current duty cycle under conditions of constant arc power. By appropriate choice of these interrelated parameters, it is shown that the arc pressure may be varied over a wide range even though the arc power is held constant. The methodology is suggested as a means of countering the effect of gravity in 5-G welding, while maintaining constant heat input to the weld. Combined with appropriate penetration sensors, the methodology is additionally suggested as a means of controlling penetration. IntroductionBoth low frequency pulsation (typically 0.1 - 20 Hz) and high frequency pulsation (> 100 Hz) are often used with GTA welding. Benefits derived from pulsing include improved weld quality and better process control.Advantages cited for low frequency pulsation include claims that the total heat input to the weld is reduced, the weld bead size is reduced, weld penetration is increased, grain size is reduced, porosity is reduced, weld distortion is reduced, thinner materials can be welded successfully, and the tolerance of the welding process to material and production variations is improved (1-16). With respect to the latter, pulsing aids control of weld bead penetration by increasing the tolerance to component dimensions and joint fit-up. It also reduces the sensitivity to disparities in heat sink, and it helps to reduce distortion in thin section material or distortion attributable to poor clamping. In certain materials it can reduce the sensitivity to surface oxides and to cast to cast compositional variations (16). Low frequency pulsation is also useful in welding thick materials mated by a prepared groove. In these applications the low frequency pulsation is used to obtain proper sidewall fusion as the tungsten electrode is weaved from one side of the groove to the other. In this case the weld current pulsation is synchronized with the cross seam weave pattern, such that the high current pulses occur at each sidewall. This type of low frequency pulsation has proven particularly useful in welding with narrow width groove designs (17-21). Finally, Ecer (22) has shown that the pulsed current arc is more stable against magnetic disturbances than an equivalent constant current arc."

Jan 1, 1986

By G. S. Hill

A large amount of the stereological error associated with liberation studies can he eliminated by assessing areas instead of linear intercepts. The presentation of a simple geometrical model as a stereological 'worst case' allows calculation of the worst possible grade/recovery curve for a given assemblage of areas. The true results are expected to lie in the window between this worst case and the hest possible case, represented by uncorrected data. The width of this window typically corresponds to an error margin of about 5% grade at a given recovery. An indication of where the data lies within the range of possible grade/recovery results may he obtained from a qualitative analysis of the locked section complexity. Assemblages consisting of texturally complex locked sections (ie. containing many mineral nuclei) are likely to exhibit minimal stereological bias and therefore will tend to lie close to the uncorrected side of the grade/recovery window.

Jan 11, 2011

By Baokuan Li, Fang Wang, Meilong Shan

"As the advantage of uniform bus loading, the electroslag remelting (ESR) furnaces with three - phase installation by delta or star connection are mainly used to produce the large or super large ingot. The electrical efficiency is significantly improved as the short circuiting through the molten slag. However, little is found about fiindamental research on the electromagnetic field of the ESR system with three -phase installation. A three-dimensional (3D) finite element model was developed to simulate the current density, magnetic field, electromagnetic force and Joule heating for a system of electrode, slag and ingot in the ESR system with three -phase installation.IntroductionThe metallurgical performance of the ingot is the fundament and precondition to obtain the large forging of high quality, which has a critical role in the producing of forging. The electroslag process (ESR) to product the metal materials of high homogenization and clarity become more and more popular[1].The electroslag process is a special smelting technology of producing small ingots, which originate in 1950[2].At present the three, four or six electrode is used in large scale electroslag furnace. It has been found that the deeper molten pool and the wider of the two-phase zone with only one large diameter of electrode to product large ingot effect the solidification microstructure of ingot[3]. However, the molten pool becomes shallow relatively with several electrodes producing the large ingot, which is benefit to the solidification microstructure of ingot. Three electrodes electroslag remelting furnace take the three phase equilibrium power supply to making the load and electric power network balance, avoiding the distortion phenomenon induced by single phase power supply and saving electric power. It also can uniformize the distribution of heat source."

Jan 1, 2012

By William E. Frazier

The presence of minute amounts of sulfur (10ppm) in nickel-base superalloys has been associated with reduced oxidation resistance and the premature spallation of protective coatings. Removal of sulfur by annealing these alloys in a hydrogen atmosphere has been successfully attempted by several researchers. This paper examines the fundamental thermodynamics and kinetics governing hydrogen desulfurization of elemental nickel. Limiting conditions for successful desulfurization are delineated. Assuming that the diffusion of sulfur is the rate limiting process of desulfurization, the effectiveness as well as time associated with hydrogen desulfurization is explored.

Jan 1, 1994

By Luben Xie, Lin Hu, Qiang Wang, Min Gan, Tao Jiang, Wenqi Li, Yi Wang, Xiaohui Fan

"The mineralization behaviors of typical fluxes are studied by investigating the microstructures with optical microscope. The results show that the reactions begin with between iron ore and lime, limestone with small particle to form primary liquid. Then coarse limestone, dolomite and serpentine take part in reaction under the action of primary liquid. Limestone is the easiest to mineralization, next dolomite, and the last is serpentine. The higher basicity and smaller fluxes size favor the mineralization process of dolomite and serpentine.IntroductionThe purposes of adding fluxes into sintering are that:(1) to increase the basicity of sinter, so as to reduce even eliminate addition fluxes into BF(blast furnace) and decrease the coke ratio of BF[1,2]. (2) to decrease the melting point of sintering mixture to ensure sintering can be carried out at a lower temperature and reduce the energy consumption. (3) to improve the qualities of sinter by forming binding phase with iron ore fines [3].Flux is another significant component for sinter besides iron ore, especially for high basicity sinter[4]. The proportion of flux is usually higher than 10% in sinter mixture(excluding return mine).There were many reports about the influence of the flux types on sintering, such as limestone, dolomite, lime and so on[5-7]. It is very important to choose suitable fluxes for iron ore sintering. Although the effect of flux size on sintering also has been researched, the mineralization behaviors of the fluxes in the sintering process has not been illuminated. The paper will study the mineralization behavior of fluxes in sintering."

Jan 1, 2011

By G. C. Yao

Branch and needle-shaped intermetallic compounds of iron, silicon and aluminum normally exist in the molten aluminum. If a suitable amount of manganese metal is added into molten aluminum, the shape of the intermallic compound particles may become lumpish and spherical. According to the difference in electric and magnetic properties of these impurity particles and molten aluminum, these impurity intermetallic compound particles can be separated by applying an alternating magnetic field. In this experiment the alternating magnetic field was formed by a "c" type loop with AC (50Hz) current. The inner vacuum of the fireclay refractory separator is 25xl5xl30mm3 with a lateral baffle inside. The separator was put into the interspace of the "c" type loop. It was found that the longer the separation time, the larger the amount transferred of impurities. The amount of transferred impurities increases with the increase of separation time and intensity of magnetic field. The addition of manganese metal enhances significantly the efficiency of impurity separation

Jan 1, 2003

By James R. Myers

A source of clean gas containing sulfur dioxide and sufficient oxygen for conversion to sulfur trioxide is essential to the production of sulfuric acid. SO2 containing gases obtained from roasting sulfide ores are heavily contaminated with inorganic dust and volatile impurities. If not removed, these contaminants will reduce product acid quality, foul the catalyst beds and mist eliminators, and accelerate equipment corrosion. This paper reviews conventional gas cleaning systems for metallurgical acid plants, followed by a discussion of modern systems utilizing DynaWave Scrubber technology. This technology is based on a unique approach togas scrubbing that can concurrently accomplish several gas cleaning/processing tasks. Scrubbing liquid is injected into the gas stream to create a "Froth Zone". This is a region of extreme turbulence, with a very high rate of liquid surface renewal. It efficiently removes both particulate matter and gas contaminants, and is also a cost effective quenching device for gases as hot as 1250 o C.

Jan 1, 1992

Studies of electric pulse (EP) disintegration were conducted on ores of disseminated precious minerals, 'on platinum-bearing chromitites of the Konder Complex, Russia, on diamond-bearing impactites of the Popigai meteoritic crater, Russia, and on and diamond-bearing metamorphic rocks of Northern Kazakhstan. It was shown that EP disintegration ~s a technology that achieves ideal liberation of disseminated minerals, and is a new efficient method to study accessory minerals.

Jan 1, 1991

By Hideki Yarnarnoto

The simultaneous removal for NH4+ and PO43- in aqueous solution was carried out by using Ca type zeolite synthesized from coal fly ash. The effect of pH on the cation exchange capacity and adsorption properties of the obtained zeolite, the simultaneous removal of NH4' and ~04'. in various solutions and the mechanism of simultaneous removal were investigated respectivel? ,The Ca type zeolite used in this study can simultaneously remove NH4+ and PO43- In aqueous solution without releasing counter ion, and this method gives great advantage over the other ordinary removal methods.

Jan 1, 2002

By Chikabumi Yamauchi, Mitsuru Tanahashi, Jutaro Miura, Takaharu Iwadachi, Toshiharu Fujisawa

"Tue oxidation behavior of molten Cu-Be alloys was investigated by exposing· the molten Cu-Be alloys to various Ar-O2 atmospheres to control the oxygen partial pressure, PO2 = 10 ~105 Pa at 1423 K. The following results were obtained:• The oxygen · partial pressure in gas phase affects the morphology of the oxide formed on the surface of the alloy and · the oxidation rate of beryllium.• At lower oxygen partial pressure, a molten Cu-Be alloy is covered with a homogeneous and compact internal layer of BeO. Thus, the beryllium oxidation rate can be minimized.• By adding a small amount of calcium or zirconium into the molten Cu-0.5 mass% Be alloy, a protective BeO layer is formed even at higher oxygen partial pressure. Thus, the beryllium oxidation rate can be reduced.IntroductionCopper-beryllium (Cu-Be) alloys are well recognized for their unique properties, such as high electrical conductivity, high strength, high fatigue strength, excellent properties at elevated temperatures, good formability and good corrosion resistance. .This extraordinary collection of properties are the reasons why Cu-Be alloys are expected to be ""Key-materials"", which are necessary to further advance science and technology and to be applied in.various fields such as electronic devices, machine parts, repeater housings of undersea optical fiber communication cables, etc.However, a large amount of beryllium is oxidized to BeO in melting stage of the current Cu-Be alloy production process, because beryllium is a highly reactive element. This is one of the ·main factors that negatively affect the production yield and th_e product quality."

Jan 1, 2000

By A. Andreas Hejja

Flow of slag and settling of matte in slag resistance electric furnaces are discussed in conjunction with furnace geometries, stirring action of the electrodes, buoyancy and electromagnetic effects. The rectangular electric furnace was regarded as a channel reactor and the mode of slag flow as a channel flow. The flow is affected both by buoyancy and electromagnetic forces, however the effect of electromagnetic forces is minimal. The flow velocity is made up of two components; (i) that developed by the action of the electrodes, and (ii) the bulk flow velocity determined by the smelting rate and the volume of the reactor. Slag samples were taken from various depths of the molten bath and were analyzed microscopically to determine the size and distribution of matte particles, The action of the electrodes was described by a simple mathematical formula indicating a balanced settling rate in the area of electrode action.

Jan 1, 1996

By Makoto Ohtsuka

The ternary Ni2MnGa intermetallic compound is an intelligent material which has both a ferromagnetic property and a shape memory effect (SMB), The use of the shape memory alloy films for an actuator of micro-machines is very attractive because of its large recovery force, The purpose of the present study is to investigate the effects of fabrication conditions and to clarify the relationships between these properties and fabrication conditions of the Ni-Mn-Ga films, The Ni-Mn-Ga films with a thickness of nearly 5 um were deposited with a radio-frequency magnetron sputtering apparatus using a NisoMn2sGa25 or Nis2Mn24Ga24 target. They were heat-treated at various temperatures between 873 and 1273 K for homogenization and ordering and then cooled in a furnace, The composition of the films depended on the sputtering power. The as-deposited films were crystalline and had columnar grains, After the heat treatment the grains widened and the grain boundary became indistinct with the increasing heat treatment temperature, The martcnsitie transformation temperature of the heat-treated films increased with increasing nickel content. Furthermore the effect of plastic deformation and constraint aging on SME is also investigated, After plastic deformation, the two-way SME was shown through the martensitie transformation and its reversion, The intensity of X-ray diffraction peaks from stress-induced martensitie phase was found, The constraint-aged films also showed the two-way 5MB by thermal cycling,

Jan 1, 2003

By Matthew John M. Krane

"The macrosegregation patterns and convective behavior of a Pb-5wt%Sb-35wt%Sn alloy are studied using new numerical treatments of solid particle motion and of transport phenomena occurring during the solidification of ternary metal systems. At this composition, the solidification which occurs while the local liquid composition is in the (Pb)-(SbSn) binary eutectic trough has a significant effect on these phenomena. The effects of this solidification path on fluid flow and macrosegregation are compared to the more familiar binary alloy patterns and the effect of solid particle transport is evaluated. The final predictions of macrosegregation are compared to measured composition profiles. IntroductionThe macroscopic maldistribution of alloy constituents during solidification, commonly called macrosegregation, is a defect which occurs in real metal processing systems. This nonuniformity of species distribution, especially when it forms a high composition gradient or a poor distribution of secondary phases, can lead to areas of high stress concentration, which contribute to cracking during extrusion or forging of wrought alloys or when an as-cast piece is severely loaded in service [1, 2]. Macrosegregation studies in binary systems have become quite common since the introduction of single-domain numerical models which feature one set of conservation equations and boundary conditions for an entire, fixed computational domain containing solid, liquid and multiphase regions. A complete review up to 1995 has been presented by Prescott and Incropera [3]. However, most commercial alloys generally have more than two species in amounts significant enough to affect the convective flows which lead to macrosegregation and other defects. The formation of secondary solid phases, including eutectic and peritectic reactions, also may occur in commercial metal alloys and should be treated using appropriate thermodynamic models."

Jan 1, 1999

By P. Myllykoski, J. Nylander

"A commercial program package called Crownoff for the simulation of temper rolling in four high mills has been verified against measured data. The agreement between measured and calculated transversal strain distributions of the strip was found to be good. Effects of the strip crown and work roll bending force on the strain distribution were simulated. The results showed that when a single ground camber of work rolls is used for all strip widths; the strip crown should be parabolic, excluding the edge drop. An increase or decrease of the strip crown by 30 % during a coil can be compensated by a 2 to 5 t change in the work roll bending force. The ability to control the strip crown by work roll bending was insensitive to strip width. IntroductionCold rolled steel strips are usually temper rolled after recrystallization annealing, which follows cold rolling. The purpose of temper rolling is to suppress the yield point, finish the strip surface and correct possible flatness errors. The presence of a yield point might otherwise cause problems during subsequent forming processes. The in homogenous yielding in non-temper rolled steels leads to the formation of Lüders bands in the strip surface.The rolling force is influenced by the rolling speed and changes in frictional conditions in the roll bite. Therefore it is very important to plan carefully the mill settings and control algorithms during rolling. The purpose of mill control algorithms is to ensure constant reduction and the best possible strip flatness during the entire coil.Correctly predicting the rolling force is important for determining the mill presettings. Torque, forward slip and power requirements are not usually critical, if the reductions are small. However, the large elastic deformations occurring in the roll bite make the physical description of the process difficult. Physical rolling models developed for cold rolling contain assumptions that lose their validity as the reductions decrease to the level of one per cent."

Jan 1, 1994

By Sheng-ping He, Zhuo Chen, Qian Wang, Kun-peng Xu

During the continuous casting (CC) process of Ti-Stabilized Stainless Steel, the nozzle clogging or even the crusts composed of TiN, Al2O3, TixOy and the complex inclusions MgOAl2O3, Al2O3 is often occurred. The main objective of the present study is to research the reaction between refining slag or mold flux and Ti-Stabilized Stainless Steel by thermodynamic calculation. A suitable refining slag composition was sought to absorb Al2O3, Tix Oy inclusions, and the reactions between different mold flux and steel was calculated and compared. It was found that a suitable refining slag was difficult to adjust aluminum and titanium to meet requirement simultaneously. The target refined slag is composited of 3–8.7% SiO2, 56–59% CaO, 33–38% Al2O3 and 4% MgO with low melting point and high absorption capacity of inclusions for in the refining of the 321 stainless steel. SiO2, Fe2O3, Na2O and B2O3 of mold flux would react with titanium in the steel. The CaO–SiO2 based mold flux had a strong reactivity than CaO–SiO2–Al2O3 and CaO–Al2O3 based mold flux.

Mar 1, 2017

By J. Boitano

This paper discusses the study, design and implementation of the new gas handling system for the Caletones Smelter of Cbdelco..Chile. A discussion on design conditions for a Mure Sulphuric Acid Plant using Teniente Converter.gases.is also included. The old system which started to be modified in 1985 and relied on natural draft and used balloon flues, resulted in a limited .gas handling capacity for operation under Mure process conditions. This system also caused excessive fugitive gases in the smelter working areas. The new system permits handling of process gases from the higher capacity Teniente converters installed in 1987-1989 Improving the gas handling of the reverberatory furnaces and Peirce-Smith converters as well as the environmental conditions of the smelter. This system utilises improved converter gas hoods, evaporative cooling and electrostatic precipitators gas cleaning, and is based on natural draft.

Jan 1, 1992

By J. W. Lyman

Nickel-metal hydride (Ni-MH) battery electrodes have been developed as a substitute for cadmium-containing negative electrodes. Use of Ni-MH electrodes offers enhanced electrochemical properties in many instances as well as reduced environmental toxicity. Rechargeable batteries using Ni-MH electrodes are also strong candidates for electric vehicles. During the production and secondary reclamation of these battery types, recycling procedures will be needed to prevent environmental impact caused by these wastes as well as to recover the value inherent in the scrap. The U.S. Bureau of Mines (USBM) is investigating hydrometallurgical technology that separates and recovers purified metallic components from Ni-MH battery scrap of two types, AB, and AB,. An investigation of acid dissolution and metal recovery techniques has determined several processing alternatives that may be used to promote the successful recycling of much of the battery fabrication scrap and eventual secondary scrap. Although recovery techniques have been identified in principal, their applicability to mixed battery waste stream and economic attractiveness remain to be demonstrated.

Jan 1, 1995

By G. L. Fredrickson, T. A. Johnson, B. R. Westphal, J. C. Wass, S. X. Li, D. Vaden

"Recovery of uranium from the Mk-IV and Mk-V electrorefiner vessels containing a LiCl/KCl eutectic salt has been on-going during the pyrometallurgical processing of used nuclear fuel for 14 and 12 years, respectively. Although austenitic stainless steels are typically utilized for LiCl/KCl salt systems, the presence of cadmium in the Mk-IV electrorefiner dictates an alternate material. A 2.25Cr-1Mo alloy (ASME SA-387) was chosen due to the absence of nickel in the alloy which has a considerable solubility in cadmium. Using the transition metal impurities (iron, chromium, nickel, molybdenum, and manganese) in the electrorefined uranium products, an algorithm was developed to derive values for the contribution of the transition metals from the various input sources. Weight loss and corrosion rate data for the Mk-V electrorefiner vessel were then generated based on the transition metal impurities in the uranium products. To date, the corrosion rate of the 2.25Cr-1Mo alloy in LiCl/KCl eutectic is ""outstanding"" assuming uniform (i.e. non-localized) conditions.IntroductionLow-enriched uranium products are being recovered from the Experimental Breeder Reactor-II (EBR-II) and Fast Flux Test Facility (FFTF) used nuclear fuels by a pyrometallurgical treatment process at the Idaho National Laboratory (INL). The treatment process comprises a set of operations designed to neutralize bond sodium, recover uranium from radioactive fission products, and place the fission products into acceptable waste forms [1-2]. Reactive sodium metal, essential for heat transfer purposes during reactor operations, is readily converted to chloride during the process. Electrorefined uranium products are currently being stored pending a final disposition decision. Treatment of the EBR-II used driver fuel was initiated in June 1996 while blanket fuel processing started in September 1998. These treatment processes continue on the balance of the used fuels."

Jan 1, 2011

By Emmanuel N. Zevgolis

After the Krupp-Renn process was shown to be unsuitable for treatment of the Greek nickeliferous laterites, the LM process was developed. It involved roasting reduction up to metallic iron in a Rotary Kiln (R/K) and smelting in an Electric Furnace (E/F). Ferronickel (with 15% Ni) produced in the E/F, was upgraded to 90-95% Ni in an 02 converter. Raw Ni was then electrolyzed to pure Ni. The LM process was not applied for very long however, due to various problems. So, the Larco process was developed, i.e., pre-reduction in R/Ks, smelting of the calcine in E/Fs for ferronickel production (15% Ni) and enrichment to 20% Ni, in an O2 converter. Until now, many technological improvements have been invented and applied or adjusted to the process, which have made it a fully reliable and competitive one. sohe of the improvements were the invention and application of a new granulation process for liquid ferronickel, the modification of the existing R/Ks, E/Fs and converters and the design of new ones, and others that are described in the paper. Keywords: Ferronickel, metallurgy, laterites, LM process, Larco process

Jan 1, 2004

By Alain Jardy, Thibaut Quatravaux, Denis Ablitzer

"A numerical model of the Vacuum Arc Remelting process has been developed and applied to simulate remelting of various metallic materials, such as specialty steels, titanium and zirconium alloys. In practice, electromagnetic stirring is sometimes used, resulting in a complex 3D molten metal flow. After having validated the numerical model for different remelting conditions, we can use it to study the effect of applying a constant or alternated magnetic field on the thermohydrodynamic behaviour of the melt pool. The intensity of flow turbulence, computed with a classical k-E model, is shown to depend strongly on the nature of electromagnetic stirring.IntroductionThe principle of the Vacuum Arc Remelting (VAR) process, illustrated in figure I, consists in melting a consumable metallic electrode of the required grade under a high vacuum, in order to obtain a sound ingot of good structural quality.During remelting, an electric arc is maintained between the tip of the electrode and the top of the secondary ingot, in order to ensure melting of the electrode. The metal droplets fall through the arc plasma and progressively buid up the ingot, which solidifies in contact with the walls of a water-cooled copper crucible. The secondary ingot formed in this way contains three distinct zones, corresponding to the liquid pool, fully solidified metal and intermediate mushy zone. In order to stabilize the arc, it can be confined with the aid of a magnetic field created by an external induction coil. This field can also be used to stir the liquid metal, the rotation induced being in the orthoradial direction. By reversing periodically the coil current, stirring can be alternated."

Jan 1, 2004