Search Documents

By P. J. Uggowitzer, H. Kaufmann

"New Rheocasting is a novel route of semi-solid casting, in which the globular semi-solid precursor material is produced by controlled cooling of only slightly superheated melts in conventional steel crucibles. The resulting semi-solid slugs are placed into the sleeve of a vertical Squeeze Casting Machine and then filled into steel dies. Solidification occurs under hydraulic pressures up to 100 MPa Due to the reduced cost of precursor material, reduced investment cost and easier recycling, the New Rheocasting process offers cost reductions of up to 25% over conventional semi-solid casting · routes. The New Rheocast products are pore free, pressure tight, weldable and heat treatable castings.In the present work the New Rheocasting Process is introduced and the influence of heat treatment on mechanical properties of the New Rheocast alloy A356 is discussed.The alloy A356 is cast under ideal New Rheocasting conditions into a step die on an UBE HVSC 350 Squeeze Casting machine. As-east, TS and T6 heat treatment conditions with variations in solutionizing and aging time/temperature parameters are applied and the samples are tested by tensile testing. Alternatively, the same heat treatment conditions are applied to conventional Squeeze Casting parts and compared with New Rheocasting.Questions of potential cost savings due to modified heat treatment conditions are also addressed in this paper."

Jan 1, 2000

By Jayagopal Ucbil, M. Krishna, V. T. Vijayalakshmi

"The pitting susceptibility of aluminium metal matrix composites reinforced with garnet particles has been examined using static weight loss method by exposing the metal matrix composites (MMC) specimens to the action of IN HCI acid at laboratory temperature for different time intervals. It was found that the corrosion rate decreased with increase in weight percentage of reinforcement while the corrosion rate was a function of the matrix alloy but not of the reinforcement material. Further, it was found that the rate of corrosion was dependent on the interface region formed between the reinforcement and the matrix. A comparison of the base matrix with the corresponding composite when subjected to heat treatment for varying periods of 4, 8, and 12 hours respectively was made. The comparison revealed that corrosion resistance of the composite increased with the duration of heat treatment and this has established a considerable improvement in corrosion resistance of the composite when compared with the base matrix.IntroductionMetal matrix composites (MMCs) offer designers many added benefits, as they are particularly suited for applications requiring good strength at high temperature, good structural rigidity, dimensional stability, and light weight [1-5]. The trend is towards safe usage of the MMC parts in the automobile engine, which work particularly at high temperature and pressure environments [6-7]. Particles reinforced MMCs have been most popular over the last two decades. Among the MMCs, the most popular families are represented by aluminium reinforced with ceramic particles. Although the incorporation of the second phase into a matrix material can enhance the physical and mechanical properties of the base metal, it could also significantly change the corrosion behavior."

Jan 1, 2000

By P. Hanniala

In the day-to-day life the copper business of today is influenced directly by the ever-increasing general concern about the environment. In addition to that the inherent shortcomings of the copper smelting business, have since many years been the falling real price level of the metals and the relatively high initial capital investments required for the production units. These shortcomings have been compensated for by high productivity, low specific operating costs, low metal inventory and unbeatable technological superiority. Thus today more than 50 % of the world primary copper is today produced by utilizing Outokumpu Flash Smelting Technology. This figure is expected to grow at an increasing speed in the near future. Characteristic for the Outokumpu Flash Smelting technology is high flexibility for a wide grade of concentrates and the highest sulfur capture owing to at the same time competitive investment and operational costs. The Flash Converting technology offers new options for copper production and optimization of the mine- concentrator-smelter production chain. In the following years it is expected that the trend in copper making is that higher grade concentrates are produced at the mines. Thus increasing amount of high grade concentrate will be available for direct-to- blister Flash Smelting causing an overall cost reduction in copper smelting i.e. both in capital and operational costs. In the '90s new technologies based on Outokumpu Flash Smelting technology have been taken into operation, thus eliminating the non-continuous Peirce-Smith converting process step. New innovative solutions have been used in the latest projects, as in Kennecott Utah Copper, where the new Kennecott-Outokumpu Flash Converting process was started up in 1995. Also, in 1995 the new DON process was started at Outokumpu Harjavalta nickel smelter followed by the Fortaleza nickel smelter in Brazil in 1997. The aim of the continuous development work at Outokumpu has been the expansion of the direct-to-blister process towards lower grade concentrates. The most recent example of this is the start-up at the Olympic Dam smelter in Australia, where the existing direct-to-blister Flash Smelting furnace was replaced with a new one having a capacity of 200 000 t blister copper per annum in just one smelting step.

Jan 1, 1999

By Ho-Jung Shin

The influence of cooling rate from 1873 to 1473 K on the size and morphology of austenite grains was studied using a Fe-O.I5 % C-I.5 % Mn alloy. The experiments were carried out at three different cooling rates of O.33KJsec, O.67KJsec and air-cooling. The austenite grain showed an isotropy at 0.33KJsec but maximized anisotropy at O.67KJsec and become much less. anisotropic. In order to account for these phenomena, a model was developed for estimating the size and morphology of austenite grains as a function of cooling rate. The driving force for the )( phase formation from 0 phase is caused by undercooling degree due to cooling rate and energy barrier is restricted to the misfit strain energy which is caused by mismatch between )( phase and 0 phase. The )( phase from 0 phase could be formed on not random orientation index systems but specific orientation systems depending on cooling rate.

Jan 1, 2001

By M. Z. Sukiennik

A static method for vapor pressure measurement up to 1450 K and above 1 hPa is presented. The method is designed for equilibrium and kinetic studies of metallic systems, including those with a chemical reaction. Application examples are given for determination of activities in condensed phases, and heterogeneous reaction rates and equilibrium constants.

Jan 1, 1993

By Sergio N. Monteiro

The interface between the matrix and the reinforcing fiber plays an important role in the efficiency by which an applied load is transmitted through the composite structure. The shear stress at the fiber/matrix interface can be associated with this load transference and,consequently,affects the composite strength. In the present work, pullout tests were used to evaluate the interfacial shear stress of curaua fiber in epoxy matrix composites. A small critical length was found for the curaua fiber embedded in epoxy, which corresponds to a relatively weak fiber/matrix bond and lower interfacial strength.

Jan 1, 2009

By Tian Tang, Sergio D. Felicelli

"The laser cladding is an important surface treatment for enhancing resistance against corrosion, abrasion, and wear. The focus of the present study is to develop a three dimensional finite element model to analyze the temperature history and thermal stress evolution during multi-pass laser cladding process on H13-H13 tool steel sample. A sequentially coupled thermal-stress analysis methodology was adopted in this study. The thermal model was firstly established to investigate the temperature history of the laser cladding process. Then the temperature history was used as input to mechanical model to calculate the thermal stress evolution during the process and the residual stress after the sample completely cooled down to room temperature. The influences of process parameters including the scanning speed and scanning strategies on temperature history, thermal stress evolution, and residual stress were investigated in details.IntroductionLaser cladding is an advanced material process technique, which is often used to improve mechanical properties or increase corrosion resistance, repair worn out parts, and fabricate metal matrix composites. In this process, the injected powder or wire feedstock material and a thin layer of substrate are melted and consolidated by use of a laser in order to coat part of a substrate or fabricate a near-net shape part.Numerous mathematical models have been established for analyzing the effects of process parameters, microstructure evolution, and thermo-mechanical behavior of laser cladding. Zhou et al. [1] established an analytical model to investigate the laser induction hybrid rapid cladding for Ni-based WC composite coatings. Huang et al. [2] also developed an analytical model to theoretically investigate the interaction between the laser beam and the powder stream of laser cladding process. A simple and realistic model of laser cladding was proposed by Picasso et al. [3]. The cladding layer is very sensitive to cracks due to the accumulation of residual stress, caused by non-uniform temperature changes, which have limited the wide application of laser cladding technique in industry. Recently, fmite element method has been increasingly used to simulate the laser cladding process [ 4-6]."

Jan 1, 2014

By Toshitaka Ota, Hisao Suzuki, Minoru Takahashi

"Perovskite-type lead zinc niobate (PZN) exhibits excellent electrical properties such as high dielectric constant, high electrostrictive coefficient and superior piezoelectricity. Therefore, PZN ceramics are very promising for high performance electronic devices. However, perovskite phase PZN is not stable under the ambient atmosphere. Accordingly, it is very difficult to prepare single-phase perovskite PZN ceramics. In this study, A-site cation of lead was partially substituted for barium to stabilize the perovskite phase of the PZN (Ba-doped PZN) powder. In addition, molecular design of an alkoxide precursor was controlled for a low-temperature processing. As a result, molecular design to suppress the lead-volatilization during calcination was preferred for a low-temperature processing. Processing temperature for a single-phase perovskite was depended on the amount of barium dopant. Doping of20 mole% of barium resulted in the single phase perovskite at 900 °C. The temperature for the single phase perovskite of Ba-doped PZN powder, which depended upon the amount of Ba-doping, was lower than that of the powder prepared by the atmosphere controlled conventional powder processing at least by 150 °C.IntroductionFerroelectric thin films and powders with perovskite structure are of renewed interest for micro-electronic applications, including ferroelectric random access memory (FRAM), dynamic random access memory (DRAM), and thin-layer capacitors integrated onto a silicon wafer [1-3]. In addition, recent advancement in micro-machine requires a high performance micro-actuator [4]. A perovskite type relaxor of Pb(Zn113 Nb213)03 is one of the promising materials for a high performance capacitor and microactuator because of their high permittivity and electrostrictive coefficient [5]. Therefore, this paper focuses on the low temperature processing of Ba-doped PZN powders.Chemical solution deposition (CSD) from molecular-designed alkoxide precursor solution is one of the most promising techniques for processing high-performance powders and thin films because it offers precise control of compositions on a molecular scale as well as a low processing temperature [6]. However, chemical solution deposition of perovskite type PZN powders and ceramics are very difficult because of the formation of stable pyrochlore phases. Therefore in the past, PZN powders and single crystal have been prepared by the hydrothermal method or flux method as well as the partial substitution method of a A-site cation [7-10]. In this study, a suitable molecular design for a preparation of perovskite type Ba-doped PZN powders with a chemical solution deposition process is investigated as well as the effect of A-site cation substitution. Chemical solution deposition from molecular-designed alkoxide precursor solution is expected to decrease the amount of a A-site substitution and/or a crystallization temperature for a single phase perovskite. This paper describes ""the relation between molecular-design and processing temperatures for a single-phase perovskite of Ba-doped PZN powders in comparison with the conventional oxides mixing method."

Jan 1, 2000

By Jukka S. Sulanto

Outokumpu has applied its well -known copper Fl ash Smelling Process also for smelting su1phide lead . concentrates. The lead in the Flash Smelting Furnace slag is recovered by reducing the oxygen potential of the slag in an electric furnace by injecting reductant into the slag bath. A series of tests have been carried out in a 1000 KVA electric furnace? adjacent to a pilot Flash Smelting Furnace. The furnace has been fed continuously with molten Flash Furnace Slag. The feed rate has varied from 0.5 to 3.1 MTPH (0.55 - 3..4 STPH) depending on the feed rate and the quality of concentrate to the Flash Smelting Furnace. The inlet slag contained 15 to 40% of lead and the cleaned slag 1. 5 to 3. 0%. The lead recovery from sol id raw material was tested in the same continuous process by feeding lead calcine into the furnace. Feed rate was 0.7 to 0.95 MTPH (0.8 - 1.05 STPH) and the calcine contained 33 to 34% of Pb. Several reduction agents and procedures were tested. The process proved to be suitable for continuous recovery of lead from solid oxide raw materials.

Jan 1, 1990

By Zhihe Dou

SHS reaction system has advantages of heat flux density, energy concentration and reaction speed, with sufficient conditions in thermodynamic and kinetic reaction. This paper invented a new technology of SHS metallurgy of preparing melting point alloys and refractory compounds using its own chemical energy. SHS-leaching process for preparing nano boron powder or ultrafine boride powder and SHS-casting process for preparing titanium-based alloy and immiscible alloy were studied. The results indicate that highly active boron powder of greater than purity of 93%, particle size less than 100nm and purity greater than 98.5%, particle size less than 400nm REB6 can be prepared. With SHS-Casting process, the oxygen content of less than 0.59% ferrotitanium, oxygen content of less than 0.5% titanium alloy and ?40-80*100mm large size of CuCr, Cu-Fe alloy ingots were prepared. This technology has greatly enhanced the thermal reduction method added values of preparing metallurgical products and its competitiveness.

Jan 1, 2014

By G. Cifuentes

The kinetics of the electrolytic oxidation of cyanide to cyanate on PbO2-coated stainless steel anodes have been studied by both experimental and theoretical means. The anodes were based on 316 steel and performed in a satisfactory fashion. The pH of the studied KCN solutions exhibited a constant value about 11. Values for all the kinetic parameters have been determined and a mechanism for the studied reaction is proposed.

Jan 1, 1999

By Batric Pesic

Solvent extraction of nickel and cobalt from the real leach solutions was studied by using a novel extraction system. The extraction system was a mixture of 2,6-bis-[5-n-nonylpyrazol-3¬y]] pyridine (BNPP) and dinonylnaphthalene sulfonic acid (DNSSA). The BNPP represents a novel molecule, which was designed and synthesized in our laboratory. Real solutions for the study were prepared by leaching of two different cobalt-nickel bearing concentrates, cobaltite [CoAsS] concentrate from Blackbird Mine, Idaho, and siegenite [(Ni,Co)3S4] concentrate from Missouri Lead-Belt. The major strength of the system was the selectivity of extraction toward nickel and cobalt from iron containing solutions. Other metals such as Mn, Mg, Ca, Al and As were not extracted. Due to the irreversibility of copper extraction, its removal from solution was required prior to the extraction of nickel and cobalt. Zinc was not as strongly extracted (i.e. its stripping was readily achieved) as was copper . Flowsheets for the recovery of nickel and cobalt were also developed.

Jan 1, 1997

Mineralogical and metallurgical scoping testwork were carried out to investigate the production of separate, marketable gold and platinum concentrates. The study utilized a flotation concentrate assaying approximately 5 wt% gold and 5 grams per tonne platinum. The gold-platinum mineralization was recovered from a placer deposit. Optical microscopy and scanning electron microscopy with energy dispersive x-ray analysis identified gold as zoned Au- Ag and Au-Ag-Cu alloys. Platinum primarily occurred as weakly zoned, variably magnetic Pt- Pd-Fe alloys. A combination of gravity and magnetic separations resulted in a gold concentrate grading 86.9 wt% Au (and 9.lwt% Ag) and a separate platinum concentrate grading 400 g/t Pt with recoveries of 94.5% and 96.7%, respectively. Magnetohydrostatic separation (MHS) using the Magstream 200 Separator indicated promising results.

Jan 1, 1994

By J. Etay, S. Daugan, Y. Fautrelle

"New type of electromagnetic parametric instabilities arising at the free surface of liquid metal in the presence of a low frequency magnetic field are presented. First, the mechanism of the instability is analysed in an idealised case. Then, the experimental device working with mercury is described. Various shapes, both regular and irregular, of free surface are found. A experimental stability diagram is obtained. Measurements of the deformation performed on photographs are compared with physical orders of magnitude.IntroductionWhen a liquid metal pool of electroconductivity a is submitted to an A.C. magnetic field B = B0 cos mt, electrical currents j are induced in the liquid metal and interact with the applied magnetic field to create electromagnetic body forces F = j x B. Those Lorentz forces comprise both a mean value (time average) and an oscillating part. Those forces are widely used in many metallurgical processes to stirr a liquid metal or to control its free surface, e. g., in aluminium continuous casting or electromagnetic levitation problems (1-3). When liquid metal free surfaces are submitted to AC. magnetic fields, the shape of those interfaces may interact with the applied field and leads to a various instabilities. A review of these instabilities may be found in Fautrelle (4). That instabilities may be a problem for the control of processing as electromagnetic levitation or quasi-levitation."

Jan 1, 1999

By Peter J. Koros

The current wave of interest in this topic is the result of increased use of titaniferous ores or ilmenite in blast furnace burdens for the purpose of repairing hearth damage. The titanium compounds that promote deposition of ?patching? materials in blast furnaces are the cause of downstream problems in the steelmaking shops. Steelmakers historically have objected to significant amounts of titanium in hot metal (>0.10 % Ti) for several reasons: 1) accretions caused by the TiC.TiN needles that float out of the iron as it cools in transit and in transfers make the accompanying slag sticky and crusty, causing problems in desulfurization and increasing time and Fe yield loss at the subsequent raking, 2) defensive measures have been taken in treatment, such as use of argon for carrier gas, but without technical rationale for this approach, 3) difficulty in removal of the ladle slag by the raker, with subsequent sulfur addition to the vessel charge, and 4) transfer into the BOF and/or formation of a very corrosive TiO2 containing acid slag during the early part of the BOF blow which, in addition to causing lining damage, results in loss of sulfur removal capability by the vessel slag. Based on a conceptual analysis of the metal-slag-atmosphere interactions during transfer ladle desulfurization treatment, a mechanism is postulated for the apparent effectiveness of the use of argon in reducing the deleterious effect of titanium and an alternate technique, possibly more effective, is proposed. As probably the use of argon causes increased exposure to atmospheric oxidation of the titanium carbonitrides contained in the ladle slag, the same benefit can be obtained by use of either oxygen or an air blast to oxidize the noxious reaction compounds. Validity of the concept has been demonstrated in a pilot plant setting. These issues, and related effects on testing the hot metal, are examined in detail with reference to the literature and plant and laboratory experience.

Jan 1, 2006

By Suman Das, Justin J. Gambone, Rohan Bansal, Ranadip Acharya, Paul Cilino

"This paper focuses on generating a quantitative microstructure prediction model for Scanning Laser Epitaxy (SLE) process based on coupled flow-thermal modeling using Finite Volume method. SLE is a laser-based additive manufacturing process for the deposition of equiaxed, directionally solidified and single-crystal nickel superalloys through the melting of alloy powders onto superalloy substrates. In the current work, the detailed effects of natural and Marangoni convection on the flow field are studied and the results are analyzed in terms of the temperature gradient, vorticity parameter, melt pool dimensions and mushy region extent. The detailed property data of the processed superalloy and the laser scan path are incorporated in the model to predict the microstructure in realistic scenario. An optimization study is carried out to evaluate the critical parameter values at which the columnar-to-equiaxed and the oriented-tomisoriented transition take place. This work is sponsored by the Office of Naval Research through grant N00014-11-1-0670.IntroductionSLE is a laser-based additive manufacturing process for the creation of structures in equiaxed, directionally solidified and single-crystal nickel superalloys through the selective melting and resolidification of superalloy powders. In SLE, a tightly focused laser beam is guided by a highspeed galvanometer scanners allowing for tight control of the amount of energy being applied to the top of the powder bed, as well as the speed at which the melt pool moves across the substrate. Under the proper operating conditions and with sufficient substrate meltback, the solidification microstructure follows the morphology of the underlying substrate, allowing for directional and even SX growth.Several reports on the modeling aspects of laser cladding-based additive manufacturing approaches can be found in the literature. Approaches based on Finite Element Methods (FEM) and Finite Volume Methods (FVM) are employed for the thermal modeling of the system [1, 2]. Gaumann coupled the Columnar to Equiaxed Transition (CET) modeling with the Rosenthal solution in earlier work based on laser cladding [3]. Rappaz et. al. provided a detailed modeling of the microstructure/columnar orientation based on the solidification velocity and crystalline orientation [4]. This approach is based on the selection of the growth direction that closely follows the melt pool normal direction. Later on, substrate orientation is also taken into account [5, 6]."

Jan 1, 2013

By Mingchun Lu, Yunjin Yan

"This paper describes a new type of bell-less top installed on two relined blast furnaces at Tianjin Iron Works and another new-built at Echeng Steel Works in China. A compact installation was presented for existing furnace top innovation with the least reformation of existing top structure. A water cooling and sealing gearbox used for driving the chute discards completely the traditional idea about necessity of continuous supply of cooling gas for the gearbox. A multiring spreader and its dozens of selectable charging patterns enables an operator to achieve optimal burden distribution easily under the condition of a minimum investment of control equipment. Some useful conclusions have been made through a small-size model and a full-scale model tests. The excellent characteristics and the superiority of the new top have been fully proved at both works.IntroductionIt is known that there are some advantages with the bell-less top of a blast furnace: suitable for furnace to operate at high top pressure, capable of realizing optimal burden distribution, less investment and maintenance costs, etc. But why do most of blast furnaces in the world still remain using conventional bell top. One of the concerns is that current bell-less tops still have some shortcomings:1) The height of a current bell-less top might be lower than three or four-bell top or two-bell plus valve seal top, but still much higher than an ordinary two-bell top.2) The gearbox for driving the rotating chute is positioned onto the lip of the furnace. It is subject to attack by crude hot bf gas. Continuously pumping cooling gas (pressurized nitrogen or clean bf gas) into the gearbox is indispensable to withstand such a harsh working environment. Therefore, a plant furnished with blower8 and its ancillaries has to be built, It involves a large sum of investment and much expense in its annual running costs.3) Although the current bell-less charging device as a means of controlling burden distribution possesses a wide range of freedom, it is difficult to realize optimal burden distribution. There are some large blast furnaces realized better burden distribution, but sophisticated control means is indispensable so that the investment of control means is much higher."

Jan 1, 2000

By David J. Krichten

A method of retrofitting air-fuel burners with oxy-fuel capability overcomes the potential problems associated with oxygen combustion in aluminum melting furnaces. The retrofit burner uses the existing combustion air connection, burner housing, and burner tile and replaces the gas tube with an oxy-gas burner. Maintaining a portion of the air flow to the burner reduces the potential for localized overheating. Proper design of the burner reduces NOx emissions by moderating the flame temperature with furnace gas recirculation. Economic analysis of using oxygen shows the benefits are increased productivity and reduced overall unit cost of melting. In practice, the melt rate in rotary furnaces increases by up to 50% and by up to 35% in reverberatory furnaces. Oxygen utilization reduces total melting cost by 112-314 cents per pound of aluminum melted.

Jan 1, 1997

By Chonghun Han, Tae-Hwa Choi, Young-Hwan Chu

"A statistical optimization method is proposed to maintain stable operation in a blast furnace with stave coolers. The objective of this study is to find the operating condition which maximizes productivity as well as minimizes the heat load on the stave coolers. In this method, we first analyzed historical data and calculated the heat flux of stave coolers and the burden distribution by mathematical models. In this approach, we determined the variables to optimize and manipulated variables to adjust these response variables. Next, we collected the necessary data for the data variables after preprocessing such as removal of noise and outlier. Finally, we constructed empirical models describing the patterns of response variables in terms of manipulated variables by partial least squares regression method, and then these models were used as objective functions for entire optimization problem. By using appropriate optimization algorithm, we determined the compromised optimum operating condition considering all response variables from the past operating conditions.IntroductionBlast furnace operation which is accompanied by complex physical and chemical phenomena is an essential process for steel industry. In this process, iron ore which is charged into the blast furnace from the top goes downward. It is reduced to iron by CO gas and is melted by the heat of combustion of coke and pulverized coal. The pig iron is tapped at the bottom in liquid phase after removing the slag, which floats on the pig iron.The cooling equipment of the blast furnace wall is changed from the plate type to the stave cooler recently. In order to cool the shell uniformly and eliminate shell spray cooling, Pohang No.2 blast furnace of POSCO (Pohang Iron & Steel Company) was equipped with 11 rows of stave coolers. These staves are only 350mm-thick including the 170 mm-deep refractory on the hot face."

Jan 1, 2001

By James T. Staley

Quenching and aging are critical processing steps used to produce precipitation hardenable aluminum alloy products. This work describes personal computer programs that employ models to predict certain properties after quenching and aging and graphically display them. One of the programs allows the user to predict the attainable strength and toughness of aluminum alloy products after an arbitrary quench. Another program simulates the changes in strength and electrical conductivity occurring during second-step aging alloy 7050-T7X products as a function of thickness, furnace temperature set point, and furnace characteristics.

Jan 1, 1993