Search Documents

By M. A. Neri

A lead-free solder alloy Sn-57.5Bi-0.5Ag has been developed by mechanical alloying and foundry processes, and has great potential as a lead-free solder system, to low temperature applications. The mechanical alloying powders show a microstructure different to the microstructure obtained by the foundry process for the same alloy. Its melting point of 142°C is slightly higher than that of eutectic tin- bismuth solder. Examination of the microstructure revealed that eutectic microstructure is refined by the mechanical alloying process Ag additions. The lamellar structure of tin-bismuth gradually disappeared with the process of mechanical alloying, while intermetallic compounds AgaSn phase was formed. The Cu-Sn intermetallic compound layer formed at solder-copper interface is the Cu6Sn5 phase. Keywords: Lead-free solder, Microstructure. Mechanical alloying

Jan 1, 2003

By Moto Goto

Onahama Smelter of Onahama Smelting & Refining Co., Ltd. has two green- charge reverberatory furnaces; the old furnace was constructed in 1965 and the new one in 1973. This paper discusses the use of oxygen-oil burners in a green-charge reverberatory furnace and also compares the copper loss in slag between the two furnaces at Onahama Smelter. During the past ten years of operation, no shutdowns of the old furnace were necessary and the smelting capacity was increased by 25% by the use of two oxygen-oil burners. These burners are suitable for a green-charge reverberatory furnace to in- crease the smelting capacity without causing an increase of the exhaust gas volume and refractory erosion. After two years of operation of the old furnace, a bottom build-up in the charging zone of approximately 50 centimeters was experienced, and this build-up has stayed at this level since then. In 1973, a new additional reverberatory furnace was put into operation. Copper content in slag of the new furnace was lower by approximately 0.15% than that of the old one during the first several months after the start-up. Investigations were then made on the effect of the bottom conditions in the charging zone on the copper content in slag.

Jan 1, 1976

By Takeo Fujino, Nobuaki Sato, Junichi Hasegawa, Masato Nakazawa, Kohta Yamada

"Tantalum oxide thin films were deposited on quartz substrates by laser ablation of Ta2O5 target using Nd:YAG pulse laser. Deposition-was observed when a laser light energy higher than 200 mJ and its repetition rate higher than 3 Hz. A thin film of 0.1 µm thickness was obtained by the ablation using a laser light of 300 mJ and 6 Hz for 2 sec. The thickness of the film increased with increasing energy, repetition rate and irradiation time of laser. By the SEM observation, it was found that many island-like particles were deposited on quartz substrate forming a thin film. The obtained thin film, which was identified as ? Ta-O by X-ray diffraction, was oxidized to Ta2O5 by the heat treatment in air at I273 K for 3 h.IntroductionTransition metal oxides have a potential to show special characteristics in electrical, magnetic and/or optical properties. When such compounds are fabricated in the form of thin film, the special properties would be improved or new characters would appear in comparison with bulk materials. Tantalum penta-oxide is widely used as a capacitor since Ta2O5 shows high dielectric constants up to high temperatures. The tantalum solid capacitor has been fabricated by the electrical oxidation of sintered Ta metal cylinder followed by MnO2 film coating. However, further improvements, reduction and layered structure formation, are required for compacting the devices. The layered structure of thin films would be applicable for the above requirements. The formation ofTa2O5 film by low pressure CVD1), photo CVD2) and magnetron sputtering3l were reported. The laser ablation -method is one of the most convenient techniques for the deposition of thin films from their compounds, such as oxides. Formation of Ta2O5 film by pulse laser deposition (PLD) method using ArF excimer4), Nd:YAG (533nm)5) and TEA CO2 6 lasers was reported. In these PLD studies, ablation was carried out in relatively high oxygen pressures resulting in formation of Ta2O 5 film. In this paper, the deposition of tantalum oxide thin film by the laser ablation of Ta2O 5 using Nd:YAG pulse laser was examined at a viliety oxygen pressures ranging from 10-8 to 10 Torr. The morphology of the films was also investigated in relation with substrate temperature and oxygen pressure."

Jan 1, 2000

By Craig A. Johnson

Cyanide speciation and behavior have been examined at three active heap leach operations, three heaps undergoing rinsing, and three sites with cyanide contaminated groundwater, all in the southwestern U.S. Data from these studies demonstrate that strong cyanometallic complexes of iron and cobalt can play ?an important role in cyanide behavior throughout the lifetimes of heap leach operations. In active circuits, we find evidence that significant amounts of cyanide combine with iron and cobalt to form strong cyanometallic complexes, and that these species can be adsorbed, probably onto iron hydroxides, or precipitated as insoluble cyanometallic compounds. When spent heaps are rinsed, the release of this cyanide is likely controlled by the slow kinetics of desorption from, or dissolution of, solids that have gone largely uncharacterized. We find evidence that strong cyanometallic complexes can give rise to transient free cyanide in some settings by rapid photo dissociation where heap rinse effluent is exposed to sunlight in open channels or translucent sample bottles. Thus, these species can complicate the ,preparation of spent heaps for decommissioning, even where regulatory standards ?are based on weak acid dissociable cyanide. There is a critical need for information on the form and stability of adsorbed and precipitated cyanide in spent ore heaps, on the concentrations of strong cyanometallic complexes in mineral processing effluents -particularly the complexes of cobalt, and on the natural attenuation of iron and cobalt cyanometallic complexes in both surface and subsurface waters.

Jan 1, 1998

By Toshihiro Kuzuya

A hydro metallurgical process has been developed for the recovery of metal values such as Co, Ni and rare earths from the electrode materials of spent nickel metal-hydride(Ni-MH) secondary battery. MmNis_xCo. (Mm : Misch metal) intermetallic compound could be separated from the electrode materials mixture by sedimentation. A typical chemical composition of MmN5-xCox was approximately, in mass%, 56.0%Ni, 13.4%Ce, 10.6%La and 7.9%Co. The time dependency of leaching intermetallic compound with sulfuric acid solution was examined with processing factors such as sulfuric acid concentration, temperature and agitation intensity, The leaching of rare earth metals proceeded very rapidly, reaching completion in less than 1.8ks. On the other hand, the slow leaching of nickel was observed. The percent of nickel leached at 328K could only reach about 70%.

Jan 1, 2003

By R. Mehta, M. Misra, X. Su

"The conventional methods to assess Acid Mine Drainage (AMD) potential of the waste rocks and tailings are based on wet chemistry and leachability tests. These methods are time consuming and expensive. There is a growing interest to develop alternate techniques to establish the reactivity of acid mine tailings and stability of treated waste forms. The Electrochemical Impedance Spectroscopy (EIS) is a reliable non-invasive technique which can be used for quick estimation of reactivity of the potential acid generating tailings. In this paper the utilization of the EIS technique for the estimation of reactivity of tailings is discussed. EIS can also be used to predict the long term stability of different stabilized waste forms.IntroductionMetal contaminated mine drainage is one of the most persistent environmental problems facing the mining and mineral processing industries today. Of all the mine drainage pollutants, acid mine drainage has become a substantial concern because of the potential long-term environmental implications and the accompanying liabilities. The main source of acid mine drainage is the tailings containing sulfide-ores which are generated during the ore processing. When these sulfide minerals, particularly pyrite and pyrrhotite, are exposed to oxygen and water they begin to oxidize. The initial chemical reactions produce acid and the acid dissolves heavy metals present in the tailings. Rainfall and snow-melt flush the toxic solutions from the waste sites into the downstream environment [1-2]. In addition to mining tailings, several Department of Energy (DOE) sites contain wastes which are contaminated with radionuclides and heavy metals."

Jan 1, 1999

By William Petruk

Many gold operations lose gold during processing because some ore characteristics which affect recoveries have not been determined, and consequently the plant could not be designed to account for them. The ore characteristics can be determined with mineralogical techniques by analyzing the plant feed, final tailings and mill products. The plant feed and/or final tailings are commonly analyzed first as a separate project. Mill products are analyzed only if the process employs a minerals separation circuit to produce a concentrate (e.g. secondary flotation circuit to concentrate gold-bearing arsenopyrite), and if assays and materials balances indicate a recovery problem in the minerals separation circuit. Many ores have been evaluated at CANMET on a confidential cost-recovery basis by custom-designing a work plan which was dependent upon the problem and on the characteristics of the ore. The reasons for gold losses have been identified in most cases, and suggestions for modifying flowsheets have been proposed. The methods used in performing the analyses are described in this paper, and non-confidential results from in-house projects are provided as examples of the benefits of such analyses. The analytical methodology involves a combination of the following procedures: -producing heavy mineral concentrates and identifying the gold minerals in the concentrates; -determining quantities of invisible gold in gold-bearing sulphides, sulpharsenides, etc. by SIMS; -determining quantities and liberation characteristics of all gold minerals and gold-bearing minerals in the sample; -finding and identifying gold minerals in silicates; -extensive grinding and cyanidation to determine the ultimate amount of cyanidable gold; -determining impact of clay minerals and graphite; -performing a mineral balance for the gold in each sample; -performing a materials balance to determine the distribution of the gold minerals, gold-bearing minerals, and other minerals throughout the flowsheet, and; -interpreting the results.

Jan 1, 1995

By M. G. Basavaraj, S. Sarkar, G. S. Gupta, P. D. Patil

"Previous experimental study on raceway size hysteresis on two-dimensional cold model showed that the inter-particle and wall-particle friction had a very large effect on the raceway size. Existing literature correlations for raceway size ignore the frictional effects. It has also been shown in the present study that their applicability to the ironmaking blast furnace is questionable. To take into account the effect of friction on the raceway size a stress analysis has been done for the raceway region. Two-dimensional fluid flow equations under turbulent conditions have been developed and solved computationally in order to get the pressure forces. The frictional forces were obtained in terms of stresses. To predict the raceway size a force balance was done for the raceway zone considering the pressure force, the frictional force and the bed weight. The resulting equations from the force balance are able to describe the raceway hysteresis phenomena reasonably well along with the raceway size. A two dimensional experimental set up has been fabricated in order to validate the computer predictions. Predicted values agree well with the experimental values.IntroductionWhen a high velocity blast of air is introduced into a packed bed through a tuyere, a cavity is formed in front of the tuyere. This cavity, formed in the iron-making blast furnace, is called the raceway. Coke tumbles down and bums in this raceway, generating heat and reducing gases for the iron-making process. The raceway is responsible for producing most of the reducing gasses in the blast furnace. In addition, the size and shape of the raceway determines the movement of solids within the blast furnace, the distribution of gases and liquids (slag and metal), setting the location where the primary chemical reactions occur and the temperature profile in the lower part of the blast furnace.Due to the importance of the raceway, many investigators l - 6 have studied it and have predicted the raceway size using the empirical correlations based on experimental (hot & cold) and mathematical models. A number of correlations have been reported in the literature to predict the raceway size by various investigators3 - 6 which are different to each other. Each of the correlations shows a different dependence of raceway diameter (DR) on bed height, particle size, solid density, bed voidage and blast velocity. None of the correlations includes the effect of solid stresses on the raceway size and shape. The magnitude of these stresses will depend on the bulk solids properties (internal angle of friction, wall angle of friction) and the bed dimensions."

Jan 1, 2001

By René Bustamante

A GPSS/H simulation is beeing done for a traditional smelter of copper, which envolves a reberberatory furnace, a set of Peirce Smith converters (PSC) and a refining furnace. The objective is to try different plant layouts, being the handling of liquid material at high temperature one the mainly concern, this envolves a study of the ladles and cranes used. Some of the modifications that can be evaluated through the model is the role of oxygen potential when tonnage oxygen is used, number of cranes, PSCs in operation, etc.

Jan 1, 1992

By J. C. Yannopoulos

The quest for a continuous copper smelting and converting process, which has been going on for a long time, has not as yet reached its objective. The most recent efforts for the development of a continuous copper?making process started about two decades ago. Among the contending proposed processes, four have been piloted and three of them are currently in operation: the WORCRA process., the NORANDA process, the MITSUBISHI process, the OUTOKUMPU process. The WORCRA process, after some long pilot plant tests, failed to develop as an industrial process: The NORANDA process, as currently operating, is a smelting process and not a continuous copper?making reactor as initially conceived. The MITSUBISHI, although the only continuous process, has not been widely accepted. The OUTOKUMPU process can be applied only to a low iron concentrate feed and co?produces blister and high in copper slag. The thermodynamics of these "continuous" systems and the practical problems of their industrial application are reviewed and discussed. The achievement of efficient and inexpensive environmental control should' be the primary objective of any new process development. A review of the environmental problems of the copper industry indicates that the quest for a continuous smelting and converting furnace should be intensified.

Jan 1, 1983

The direct removal of lead ions from D2EHPA-kerosene using metallic zinc as the reducing agent was evaluated. The electrochemical process, called galvanic stripping, is a potential alternative stripping technique when standard chemical methods are not adequate. Four parameters found to be important in the rate of lead removal were studied in a factorially designed experiment. The variable evaluated included D2EHPA concentration, temperature, zinc surface area and solution agitation. Temperature and surface area were found to be the most significant, while agitation and D2EHPA concentration had less influence on the reaction. An activation energy of 22.5 Kcal/mole was calculated indicating a chemically-controlled process. The reaction was also sensitive to the concentration of oxygen in the system. The zinc required was considerably in excess of stoichiometry, possibly due to the dissolution and redeposition of lead: In general, the results were encouraging and demonstrated that lead impurities could be removed from D2EHPA using cementation type reactions.

Jan 1, 1995

By Ozgul Dere Ozdemir, Muge Sari Yilmaz, Sabriye Piskin, Deren Sibel Kasap

"Galvanic sludge is generated at the end of the waste water treatment process of metal plating system. The waste sludge is one of the main hazardous solid wastes produced by metallurgical industries. It is caused the harm of human health and damage of the environment due to containing reasonable amounts of toxic metals (e.g., nickel, zinc, copper, chromium, iron, lead, cadmium, etc). The concentration of those toxic metals in the wastewater might reach 30% (w/w, dry weight) making their removal and recovery an interesting issue.In this study, synthesized titanium dioxide is used as adsorbent to remove nickel in leachate of galvanic sludge. The adsorption experiments were carried out isothermally at four different temperatures. The effects of pH, temperature, and contact time on nickel adsorption efficiency were investigated, and the optimum parameters were determined from the experimental studies. The experimental results indicated that pH, temperature, and contact time played a significant role on the adsorption capacity of nickel.IntroductionRapid industrialization has caused increasing the heavy metal concentration in biosphere with the industrial wastes. These wastes are generated in various industrial processes such as electroplating. Galvanic sludge is a hazardous waste that generates from metal plating industry by chemical precipitation of heavy metals from acidic or alkaline solutions during the waste water treatment process. Heavy metals are tend to bioaccumulate thus they are treated the living organism [1-2].Galvanic sludge is mainly disposed on landfills for these reason it is a big problem for environment. Galvanic sludge containing nickel (II) is common because nickel (II) is used in electroplating process [3]. In drinking water, nickel may cause health problems if found in amounts greater than the health standard set (MCLG: 0.1 mg/L) by the United States Environmental Protection Agency (EPA). The higher concentration of nickel (II) in ingested water may cause severe damage to lungs, kidneys, gastrointestinal distress, e.g., nausea, vomiting, diarrhea, pulmonary fibrosis, renal edema, and skin dermatitis [ 4]. For these reasons, it must be treated before disposed to landfill."

Jan 1, 2011

By Kotaro Ogura

"Ethylene has been produced in aqueous solution from CO2 by the electrochemical reduction driven by a natural energy. This process is useful for storing a large amount of the natural energy. In the closed system, the conversion efficiency of CO2 is almost 100%, and the maximum selectivity for the formation of ethylene is more than 70%. On the other hand, the current efficiency for the competitive reduction of water is less than 10%. The electrolysis is practicable under such special conditions as three-phase interface consisting of gas, solution and metal, concentrated solution of potassium halide, low pH and copper or copper halide-confined metal electrode. These requirements are thoroughly examined, and the grounds to reply upon are revealed. A series of chemical apparatuses including an electrolytic cell in a large scale are designed for the ethylene production, which allow us continuously to supply raw CO2 and to extract the product.IntroductionIn connection with the depletion of the petroleum reserve, much attention has been paid to the utilization of natural energies such as sunlight, wind force and waves. However, these energies are always changeable, and some means of storing them are necessary for the common use. In general, natural energies are transformed to the electric energy at the time of utilization, but the electricity is not very storable. This is one of the reasons why the application of natural energy is not so expanded. On the other hand, the storing of natural energy by plants is very skilful. In the photosynthesis, solar energy is transformed to chemical energy by fixing carbon dioxide."

Jan 1, 2009

By Nicole de Jager, Michael J. Nicol

"In order to liberate gold from refractory gold ores and concentrates it is generally necessary to oxidise the surrounding sulphide minerals, typically pyrite and arsenopyrite. Traditional methods of oxidation include pressure leaching, roasting and bacterial oxidation. In recent years, bacterial and pressure oxidation have found increasing favour, although these methods are by no means completely satisfactory and each is subject to particular disadvantages.A novel process has been developed as an alternative to the traditional methods whereby electro-generated ferrate(VI) ions in alkaline solution are used to oxidise a pyrite concentrate. This process has been observed to proceed fairly rapidly and could prove to be a more economically viable process, as well as being more environmentally acceptable. As an added benefit, operating in an alkaline environment is advantageous for downstream cyanidation processes.Ferrate(VI) is a relatively unknown species, due mainly to its instability in acidic solutions. However, in alkaline solution it has been observed to be sufficiently stable for use as an oxidant when used under favourable conditions. Ferrate(VI) is most conveniently manufactured electrolytically via the dissolution of high-carbon anodes in strongly alkaline solutions. Some literature has been published on the electrolytic generation of ferrate(VI) and relatively high efficiencies have been observed by both the authors and other researchers.This study utilises both electrochemical techniques and leaching experiments to examine the kinetics of the oxidation of pyrite by ferrate(VI), which is produced electrolytically. Cyclic voltammetry, rotating disk voltammetry and potential step experiments have been used to investigate the kinetics and mechanism of the oxidation process."

Jan 1, 1997

By Chen Song

Cobalt basic carbonate particles were precipitated from 1.0mol cobalt nitrate or cobalt sulfate solution with ammonia carbonate. By controlling the zeta-potential of the particles and the ionic strength of the solution, the uniform particles with ellipsoid or rod shapes were obtained. During the precipitation process, the interface tension was diminished to the minimum and therefore the Ostwald ripening and secondary nucleation were both inhibited. The morphology and the size control by zeta-potential seem to be the result of thermodynamics rather than classical crystalline kinetics. The particle sizes were in the range of 0.4-0.6, 0.3-0.4 micrometer. After thermolysis, the spinel-type C0304 particles were produced. The morphologies of C0304 particles were similar to that of their precursors.

Jan 1, 2003

By Herbert H. Kellogg

A model of the ISF is described. which reproduces with accuracy the "normal" operation of three industrial furnaces. The model, written in Fortran, is based on detailed heat and material balances, and the concept that the ascending gases reach equilibrium with zinc oxide and with the water-gas shift reaction. "Solution loss" of carbon in the lower shaft, and partial reoxidation of zinc vapor in the upper shaft are also essential features. For prediction of furnace behavior under altered operating conditions (blast rate, temperature, moisture content, oxygen enrichment, or injection of oil or coal through the tuyeres) the model modifies the heat loss, temperature of slag and bullion, amount of reoxidation in the upper shaft and the condenser efficiency to reflect the altered operating parameters. Model predictions for such operating conditions are in reasonable agreement with plant experience.

Jan 1, 1990

By Honggang Zhong, Xin Cao, Qijie Zhai, Hongmei Song, Congsen Wu, Cheng Zhang, Jingzheng Ye

"The influence of superheat on the solidification structure and ferrite/austenite phase transformation of a novel lean duplex stainless steel (DSS) was investigated on a setup, which designed to thermally simulate the continuous casting process. The results showed that the macrostructure of the samples all exhibited chill zone, columnar zone and equiaxed zone. The distance from chill zone to position of columnar to equiaxed transition (CET) moved from 51.0 mm to 39.8 mm with an decrease of superheat from 70 °C to 10 °C, and that the grains in the chill zone tended to be finer. In equiaxed zone, the fme and uniform grains were observed when superheat higher than 40 °C; while, coarse grains were found in samples poured at low superheat. Generally, the volume fraction of ferrite increased along the dendritic growth direction, and stabilized in equiaxed zone. The high superheat decreased the volume fraction of ferrite in equiaxed zone, while it had indistinctive influence on chill zone and columnar zone.IntroductionDuplex stainless steel with approximately equal volume of ferrite and austenite, offering an attractive combination of corrosion resistance and mechanical properties. [ l]. The production of DSS, worldwide application in structural engineering[2] and petrochemical industry[3], have increase by more than 100% in the latest decade[4]. But due to the sharp prices increase of nickel and chromium, lean duplex stainless steels which have lower contents of alloy elements were developed. They perform well in both mechanical and corrosion resistance[S, 6] and even have TRlP(Transformation Induced Plasticity) effect[?]. Nonetheless , the mechanical properties of DSS was affected greatly by the solidification structure, such as columnar to equiaxed transition (CET), grain size and phase content[8]. So, the solidification behavior of stainless steel was investigated widely"

Jan 1, 2014

By Jun Deng, Daohong Wu, Zhicheng Cao, Jingkun Tang, Luxing Feng, Xun Xue

The effect of reducing temperature, H2/CO mole ratio, and reduction gas flow rate on the metallization rate of oxide pellets were investigated at laboratory scale, with ludwigite iron concentrate used as raw materials. The reducing temperature varied from 850 to 950 °C, the H2/CO mole ratio changed from 1.5 to 4.5, the range of reduction gas flow rate was from 2 to 5 L/min. The results indicate that the metallization degree of pellets increase with increase of the temperature, H2/CO mole ratio, and gas flow rate. However, after temperature rises to 850 °C, metallization degree increases slowly. The effect of H2/CO on the metallization degree is not very obviously with the ratio of H2/CO increasing from 1.5 to 4.5. When the gas flow rate was increased from 2 to 3 L/min, the metallization degree increased greatly from 72.2 to 92.1%. In the flow range from 3 to 5 L/min, the metallization degree was increased slowly. The results obtained could be useful for comprehensive utilization of ludwigite iron concentrate by gas-based direct reduction method.

Mar 1, 2017

By W. Song, C. Richards, B. Q. Li

"This paper presents a two-phase flow numerical model for spouting gas-particle flow reactors used in chemical vapor deposition processes for manufacturing heart valves and other biomedical implants. The model is developed based on the Eulerian-Eulerian formulation of gas-particle flows, with the k-e engineering model modified with the presence of particles for the description of turbulent gas flows. In parallel with the numerical model development, physical models are set up, where the particle image velocimetry is used for visualizing the particle flows and spout shapes and heights and optical probes are used to measure the particle velocities. The numerical model predictions are compared reasonably well with the experimental measurements.IntroductionVarious biomedical implant components, such as bone joints, dental components and heart valves, are coated with bio-compatible thin films by chemical vapor deposition in particle-laden chemical reactors [l-5]. In these reactors fine particles are used as packing and supporting media. During the coating operation, these packed particles are fluidized by an upward gas jet from the nozzle, reach a certain height and fall back on the top of an annulus region. These recirculating particles are mainly for levitating the implant components (usually one or two in a reactor at one time) so that every portion of them is equally exposed to the gaseous atmosphere. An equal exposure is critical for forming a uniform, mechanically strong and corrosion-resistant coating on implants. Plant experience shows that the quality of the coating is directly related to a stream of operating parameters such as temperature, particle size and loading, and gas flow rates [6]. Optimization of these operating parameters for improved reactor performance depends crucially upon our fundamental understanding of the physics governing the gas-particle flow, heat, and mass transfer phenomena taking place in these reactors."

Jan 1, 2004

By Margarete Kalin

Mine abandonment is associated with the securing of access to underground workings, shafts, raises and adits. Waste rock piles and tailings are generally contoured and revegetated. When the waste materials contain pyritic material seepages can often emerge long after the physical reclamation work has been carried out. Their extent and origin has to be delineated to facilitate remedial measures. The depth to which the seepages extended can be determined with an electromagnetic (EM) survey. This paper reports on the experience gained using a winter and a summer EM survey correlated with measurements of specific conductivity at the sediment water interface. Lake sediments and ponds which represent a homogenous background material are good media, where specific conductivity and electromagnetic conductivity can be correlated. The origin of the seepage within the recontoured mine site requires detailed site knowledge, as many anomalies in heterogenous materials such as represented by a mine site are evident.

Jan 1, 1994