Search Documents

By Peter Cain

Longwall extraction in the Phalen Scam in the Sydney Coalfield of Nova Scotia is carried out under flooded abandoned workings in the Harbour Seam 140 m above, and at depth of up to 700 m beneath the Atlantic Ocean. Careful planning of panel and pillar dimensions is necessary to prevent inflows from the overlying workings and to prevent the development of excessive subsidence strains at the seabed. This paper briefly summarises the research undertaken over the past five years by CBDC and CBCRL into the problems associated with mining under water, and then describes the development and application of a design/planning code of practice developed jointly by CBDC, CBCRL and mine regulatory agencies. The design method employed in the Code of Practise is based on empirical data from the coalfield and parameters developed from subsidence modelling and previous water inflow experience. It includes precautionary measures to be adopted during development and mining, and monitoring procedures to be followed. It is flexible enough to allow future developments in the understanding of inflow mechanisms to be incoporated without major modifications, and represents a major step forward in reducing the potential hazards associated with coal extraction in the coalfield.

Jan 1, 1996

By David Newman

Multiple seam underground coal mining is ubiquitous in Appalachia. Many coal properties have from two to ten or more economically mineable coal seams. Because of the ability to penetrate 600-feet to 1,000-feet or deeper into the mountainside leaving panels of web pillars separated by barrier pillars, highwall mining is a hybrid between surface and underground mining. As a result, many of the ground control problems commonly associated with multiple seam underground mining exist with multiple seam highwall mining. These include: i) superjacent mines, subsidence and caving propagating to overlying seams and ii) mines, pooled water and the potential for inundation resulting from a iii) breakthrough between an active highwall mine and abandoned underground mines in the same or superjacent seams, the presence of overlying or underlying mine workings where iv) pillar columnization in the active mine is not possible, and v) the question of whether to mine ?top-down? or ?bottom-up.? Case histories are presented from southeast Ohio where the Middle Kittanning No. 6 and Lower Kittanning No. 5 seams are successfully highwall mined with 20-feet to 40-feet of largely shale interburden. A highwall miner was caught in a highwall collapse in the Middle Kittanning No. 6 seam when it was overmining auger workings in the Lower Kittanning No. 5 seam. Multiple seam interaction caused by the overmining transferred overburden stress onto the Lower Kittanning No. 5 seam. The overburden concentrated through web pillars initiated auger web pillar failure, resulting in roof collapse and subsidence in the Lower Kittanning No. 5 seam that propagated up to the Middle Kittanning No. 6 seam. A second case history involves multiple seam highwall mining in southeast Kentucky. The A3 Rider, A3, B2, and C1 seams are being highwall mined around abandoned underground mines in the A3 and B2 seams and augering in the A3 Rider. Because of spoil storage constraints for the surface contour mines, the highwall miner follows the active pits in each seam so a standard sequence of ?top-down? or ?bottom-up mining does not exist. The planning and engineering design considerations associated with each case history is presented along with geotechnical information. In the case of the highwall collapse a back analysis is presented of the stability and safety factors for the auger webs, highwall miner web pillars, and barrier pillars.

Jan 1, 2009

By Richard E. Gray

Subsidence due to coal mining is poorly understood by non-specialists. This has led to numerous misconceptions and myths based on limited observations and lack of knowledge. The three most common are: 1. Mine maps are inaccurate. 2. Deep mines are not a problem. 3. If no subsidence has occurred for many years after mining, there is no risk of future subsidence. Maps are important during mining and most are carefully prepared. Future use to evaluate conditions at mine level often includes drilling to confirm what the map shows. Usually, little or no effort is made to tie the surface survey of the property to the mine survey, to conduct a well designed drilling program to confirm the mine map, or to drill test borings vertically. When a mine entry is encountered rather than a coal pillar, or vice versa, and conditions at mine level appear different than anticipated, the first reaction is the mine map is inaccurate. The idea of a safe depth from subsidence is often based on the false premise that mining results in sufficient breakup of the overlying rock strata that bulking compensates for the coal extracted. The safe depth idea first appeared in the literature about 1880 and remained prevalent well into this century. Sadly, it is still encountered. The modern understanding of fragmentation of the immediate mine roof with the overlying beds sagging down on the broken roof rock was first described in 1900. With full extraction mining, either longwall or retreat room and pillar, surface subsidence occurs regardless of the depth of the mine. Subsidence over longwall mines at depths of 2000 feet can be 90 percent of the mined seam thickness. Numerous studies of undermined sites conclude that mining occurred many years ago and since no subsidence has occurred, there is no risk of future movement. This is true if sufficient coal pillars have been left to support the overlying strata. However, every year subsidence occurs over mines that have been closed for 100 years or more. In a study of subsidence incidents over the Pittsburgh Coal, the senior authors found that 50 percent of the incidents occurred above mines that had been closed for at least 50 years and 10 percent over mines closed for at least 80 years.

Jan 1, 1996

By Peter Cain

The paper presents previously unpublished results derived from an unique interaction moitoring program conducted in the Sydney Coalfield of Nova Scotia. An abandoned, sealed longwall gateroad was re-entered and instrumented prior to extracting a longwall face 140 m below it. Instrumentation included piezometers connected to a constant head tank to monitor subsidence, and horizontally mounted extensometers to measure strains associated with subsidence. Survey levelling data was also collected. The monitoring results have allowed a number of significant conclusions to be drawn, all of which were either unanticipated or contradict current mainstream thinking. Firstly, interaction subsidence was less than anticipated. Secondly, the effects of rate of face advance on the development of the subsidence profile are evident. Thirdly, compressive strains are shown to remain in the subsided strata. Finally, strata response to undermining was almost immediate. The impact of these findings on the extraction of longwall panels beneath flooded workings in the Sydney Coalfield are discussed.

Jan 1, 1996

By Vedala Sastry

Longwall mining for coal extraction in deeper deposits is gaining momentum in India, due to the increasing stripping ratios and depletion of shallow deposits amenable for surface mining. In longwall mining, presence of multiple seams with varying interburden thickness is a major problem especially while planning for over-mining. An investigation program was taken up to analyze the effect of the presence of goaf and virgin coal blocks in already developed and extracted lower seam by bord and pillar mining, on the stress distribution in the longwall panel in upper seam. Studies revealed marginal increase in horizontal and shear stress as longwall face passes above goaf to the virgin area present in lower seam. Stress distribution over chock shields was considerably affected when the face in upper seam reached 15-25m zone above the galleries in the lower seam. A clear influence of the presence of solid coal, galleries and goaf in lower seam was found in the loading of longwall panel in upper seam.

Jan 1, 2007

By R. D. Yancich

A case study of longwall mining surface subsidence was performed at a mine in Southwestern Pennsylvania. The mine operated in the Pittsburgh coal seam which averaged 70-72 inches with 6-8 inches draw slate in the longwall location. The average overburden depth ranged from 625 8eet to 660 feet. Three adjacent longwall panels were studied and classified as Panel 1, Panel 2, and Panel 3. The following is information on each and can be seen on the General Mine Map (Fig. 1).

Jan 1, 1984

By C. Fairhurst

Most of the papers designated as being within the topic of underground storage at this Symposium are concerned with aspects of radioactive waste isolation. Although this is, unquestionably, an important international application of underground storage, and one involving a considerable number of research investigations, the subject of underground storage is indeed much broader. Several major international conferences have been devoted exclusively to it. Applications include storage, under a range of temperatures and pressures, of oil and liquefied petroleum products, compressed air, heat, foodstuffs of various kinds, hazardous and 'nuisance' industrial by-products, and a variety of special applications, both civilian and military - some in use, others proposed. Storage may be in caverns excavated specifically for the purpose, exhausted mines may be adapted for storage or, in some cases, the material to be stored may be injected under pressure into the pore spaces of porous-permeable formations at depth. A variety of rock types and geological environments are used, e.g. excavations in salted or domal salt, where long-term creep closure of the openings is a concern; massive granite, where fluid loss through fissures may be important. Cavities may have spans of several tens of meters, and there is interest in achieving still larger excavations. As would be expected, this breadth of underground storage applications introduces a similarly broad range of questions in rock mechanics and rock engineering. The report will review these questions and recent developments in rock mechanics research, computational procedures, and design applications - and will also discuss the opportunities for a still greater range of applications of underground storage to current industrial and social problems.

Jan 1, 1989

By Khamis Y. Haramy

This paper summarizes ground control studies of longwall panel entry systems in two Western U.S. coal mines. Presented are comparisons of in situ pressure change measurements and assessments of chain pillar and entry behavior under a wide range of cover. Results indicate that no one entry system design is universally applicable, and that site-specific factors need to be considered for panel entry design. Relationships between overburden depth, face advance, and magnitude and location of the forward abutment are discussed for western operations. In addition, analysis indicates that use of yield pillars may reduce or eliminate some stress-related problems that plague longwall panel entry design.

Jan 1, 1989

By Ken Mills

A program of stress change and roadway deformation monitoring was undertaken to measure the forward abutment load distribution about a retreating longwall panel at Dartbrook Mine. The results of this monitoring allow roadway conditions observed at various stages of mining to be ranked according to the estimated vertical stress they have experienced. This ranking also provides a means to predict and visualise future roadway conditions at various stages of mining. This paper presents the results of the monitoring and describes the approach developed to predict future roadway conditions. The monitoring results show the vertical stress distribution associated with the front abutment from a longwall goal decreases exponentially away from the goaf edge. The vertical stress distribution peaks at the goaf edge at 5 to 6 MPa stress increase and decreases to 1 MPa within 50 m becoming imperceptible beyond 100 m By scaling this measured distribution to reflect the loading environment, the vertical stress can be estimated for different overburden depths and different stages of mining. Photographs of roadway conditions at particular vertical stress levels provide a way to visualise roadway conditions at various stages of mining in the future

Jan 1, 2000

By G. P. Neobutov

The near surface inclined gold ore deposit is mined out at freezing temperature. The replacement of ore pillars by artificial freezing rocks during the rock pressures control in this conditions presented no difficulties. At the present, the mining operations are maintained at a depth of more than 300 meters. The exploration of mining conditions showed partial warming of rock mass and unstable ground conditions. Analytical calculations using a mathematical model of heat exchange predicted undesirable duration of freezing of artificial pillars. Practical techniques and recommendations for mining with ice pillars as an artificial support system using a new freezing method are discussed.

Jan 1, 1996

By Rob Thomas

Adequate load transfer is considered essential for optimum ground support and is increasingly important in weak roof and/or high stress environments. If adequate load transfer is achieved not only can this have a positive impact on the resulting roof behavior, but it may also allow the use of lower and hence more economic densities of roof support. A wide variety of post-groutable cable bolts are currently in use in the Australian coal mining industry, each of varying capacity, design, and grouting methodology. Though all of the cables are supplied with the appropriate steel specification, strength, and modulus data, the Australian coal mining industry does not have access to a comprehensive and comparative database on the corresponding load transfer performance, which is a critical problem. On the basis of the above, this paper describes the methodology and results of a laboratory pull testing program that aims to assess the impact of cable bolt design on load transfer, and specifically, the impact on the capacity and stiffness of the anchorage. As part of the testing program, 19 cables were tested including (1) plain-strand cables installed in holes drilled with 28 to 55 mm diameter drill bits and (2) bulbed and nutcaged cables installed in holes drilled with 42 to 64 mm diameter drill bits. Other parameters assessed included the significance of smooth and profiled wire, wire packing, and expanded geometry bulbs. The main results of the testing indicate that in comparison to plain-strand cables, if the cable is bulbed or nutcaged, the capacity of the anchor can increase by up to 400%, and the peak stiffness by between one and two orders of magnitude. The results also indicate that increasing hole diameter may have a positive impact on load transfer in the case of bulbed or nutcaged cables and a negative impact on plain-strand cables. No conclusive results were obtained with regard to the impact of grout strength on load transfer.

Jan 1, 2012

By Jon Bowler

Daw Mill Colliery, UK Coal, near Coventry in England, mines the Warwickshire Thick Seam at 800 m/2500 ft depth using longwall retreat with gateroads supported by rockbolts. Over the last eight years the mine has worked longer and wider panels with extraction heights of over 5 m. Recently the mine has experienced high deformation conditions principally from the rib sides resulting in operational issues and production delays. Investigation of rib deformation was undertaken using new inspection and measurement techniques, including systematic laser surveying, and improved rib support consumables were developed and introduced. A new rib trussing system using textile webbing has proved very successful.. A rib support management system was also developed and introduced for face retreat. This allowed rib support to be more effectively managed both for production and safety. For the current developments, new 28-mm-diameter roof and rib bolt systems have been introduced and rib bolt length has been increased to 3 m, with the aim of achieving gateroad stability over the life of the panel. Significant reductions in roof and rib deformation have been confirmed by the latest monitoring results. These ground control innovations are allowing Daw Mill?s potential to be realised. Production from 302?s face in 2008 set new UK and European records. However the support enhancement process continues and further innovations are planned.

Jan 1, 2009

By Bernard Woolley

The history of the use of calcium aluminates in mining is discussed including a review of very rapid hardening concretes, anchoring using cement capsules and pumped ground control systems. Specific reference is made to the long term performance of highly abrasion resistant orepass lining in South Africa and the use of rapid hardening materials for a range of applications in Australian coal mine where water infiltration creates difficulties or where rapid repair or return to service is required. The topics covered in detail are, high strength abrasion resistant concretes with a 20 year, 30 million ton ore pass life. Rapid reinstatement of wet and worn roadways using mineral dewatering and rapid roadway rebuild solutions, all in I maintenance shift. The different applications are illustrated using examples from operating mines.

Jan 1, 1997

By Y. L. Sun

The feasibility of using the ultrasonic wave attenuation method for measuring in-situ stress is examined theoretically and experimentally. The theoretical analyses show that for a given rock type the relation between stress and attenuation coefficient ratio can be approximated closely by second-order polynomials. Combining the elastic and statistical theories, the magnitude and direction of the existing principal stresses can be predicted by using the relations between stress and attenuation coefficient ratio obtained in the calibration of core specimens. Several experiments are conducted in the laboratory on two types of rock. The experimental study consists of two parts: the attenuation-coefficient measurements in core specimens under uniaxial stress and the attenuation coefficient measurements in boreholes drilled through blocks of sandstone and limestone subjected to uniaxial compressional stress. Compressional waves are used exclusively in the measurements.

Jan 1, 1989

By Michael Bayerl

The HILTI OneStep rockbolt was implemented for roadway development in German deep coal mines in 2004. The development by HILTI Company is based on a technical joint venture with RAG Deutsche Steinkohle AG. The technical development of a One-Step bolting system was required for weak strata conditions at the roadway development face. Standard resin bolting has reached the limit of performance when boreholes are squeezed and cannot be filled with capsules. In some cases the heading face is brittle and requires additional support for installation of the bolts and a person working immediately next to the borehole. The Hilti One-Step system allows automated and safe processing at the heading front and provides the key technique to avoid these problems.

Jan 1, 2009

By V. D. Jalevsky

A new methodology of an experimental-analytical approach has been developed. It is used in building an information geomechanic monitoring system for the modeling of geomechanic processes during coal seam working. The approach synthesizes experimental (in-situ) measurements of rock pressure manifestation in separate points, methods of numerical modeling of processes on rock boundaries with coal, and a seam analytical calculation of rock mass in a spatial strained state. One of the realizations of this approach is the developed theory and calculation method of adjoining rock surface shift (overhang) formation during underground working of sheet deposits and of rock mass geomechanic state determination. There are description algorithms of cavity configurations with broken lengths of faces during underground working of useful mineral sheet deposits. These algorithms have been used in computer modeling of formations of adjoining rock surface overhangs and abutment pressure upon rock mass in the area of coal faces with irrectilinear longwalls. Peculiarities of surfaces shifts and stress allocation are established for different face schemes. The use of theory and methods alloww working out techniques of automatic control to receive processing algorithms of RPM measurement results and calculate geomechanic situations within panels in the process of planning and development as well as during mining, i.e., to carry out long-term prediction, in-line control, and short-term prediction of rock pressure manifestations.

Jan 1, 1996

By Rudiger Baltz

The sudden failure of bodies of rock is a serious problem commonly experienced in the international mining industry. These explosive releases of energy are referred-to as ?bumps?, ?outbursts? and ?rockbursts?. Rockbursts can occur at such a rapid speed that they present a direct threat to safety in large parts of the mine workings. The build-up of excess stress within the body of rock can be attributed to different causes. In shallow workings, for example, sudden and violent failure of the roof strata can be caused by leaving insufficient pillar width when practising room-and-pillar mining. At much greater working depths, as it is the case in the German coal industry, rockbursts are generally attributable to high levels of rock pressure. This can even result in coal outbursts when driving individual roadways. More than thirty years ago the German coal industry suffered from numerous rockburst incidents which caused many deaths and serious injuries. This led directly to the establishment of the Rockburst Prevention Centre, which was created at the instigation of the mining companies and the chief mines inspectorate. The consistent logging and analysis of all rockburst incidents has led to the development of a system that is still used as a basis for preventing underground rockbursts and minimising the risk of such phenomena occurring. Working closely with the mining authorities and mining companies the accredited experts of the Rockburst Prevention Centre have played a key role in helping to develop and implement a range of methods for the early detection and prevention of rockbursts.

Jan 1, 2008

By Danell. R. E.

A drill monitoring system has been developed which measures performance characteristics of a rotary drill and relates this to the material strength and rotary specific energy. The drill monitor is computer based and is used to produce a profile of the relative in-situ material strength as a function of depth. This information has been used in determining the placement of explosive in selective loading of blastholes and estimating the amount of lump product in a particular section of an ore body.

Jan 1, 1989

By W. G. Pariseau

A crown pillar cave occurred at the Ropes Mine in December, 1987, that resulted in closure of the mine. Production was resumed soon afterwards with the formulation of a rock mechanics plan designed to address several issues of safety and stability. The plan proved to be successful and shows what can be accomplished in the realm of applied rock mechanics where a cooperative atmosphere exists.

Jan 1, 1989

By Monika Patrycja Polak - Micewicz

This paper presents an approach for estimating the fatigue life for the base of powered roof supports (shield) manufactured by the FAZOS roof support company. FAZOS?s powered roof supports are designed to operate on an inclined coal seam in full caving with a medium, strong roof strength. This shield support is utilized in conjunction with a shearer and face conveyor for a complete longwall mining system. To design shield support, it is essential for contractor to know the physical (hardness, toughness, etc.) and mechanical properties of material (tensile strength, Young?s modulus, etc.) used for the shield support as well as the geotechnical properties of the mine site. The fatigue strength of the shield support material depends on the mean stress, alternating stress, cycle frequency, transport dimensions, mine environment and other factors. In order to estimate the fatigue life for a powered roof support system, it is assumed in this paper that the support must keep the roof stable in the mine under variable load cycles. The approach selected in this study contains Goodman?s model (Goodman, 1899) for all blocks in the design housing which is subjected to sinusoidal load. On this basis, the degree of fatigue damage was calculated and compared to the results of experimental tests. It will be shown that there is a significant detrimental effect on the fatigue life of the base of the powered roof supports due to geometrical notches. The Ramberg-Osgood model and damage accumulation rule (Palmgren-Miner) (Miner M., 1945) were used and numerical analyses were conducted, utilizing ANSYS finite element software. These analyses play a very important role in longwall casing design. The proposed method allows assessment of the yield state and forecast of the structure cracking, taking plastic strains occurrence into account. The presented method is universal and can be applied for fatigue life estimation of other subassemblies of powered roof supports. The final portion of the paper presents results of variable amplitude loading simulations on the S355N and S690Q steel used to make powered roof supports. The results of the physical tests were compared with the results from finite element methods. The proposed approach to calculate fatigue life gives the best correlation between the experimental results and calculated values of fatigue life for the powered roof support base. Finally, the design process uses a simple approach to predict fatigue life in a short time, reducing design costs and providing longer service life for roof supports.

Jan 1, 2012