Search Documents

By Keith Heasley

In many practical situation where the LaModel program in used to analyze the mechanical response and failure of the mining environment, there are very few actual field measurement from the site available for deriving the appropriate input parameters. For coping with this typical lack of field data, this paper presents some recommended calibration techniques derived from on an in-depth understanding of the laminated model formulation and from many years of experience applying LaModel to practical situations. For each of the critical input parameters (rock mass stiffness, gob stiffness and coal strength) in LaModel, a specific calibration technique is recommended and presented along with the justification for the technique and some appropriate derivations/equations for assistance. It is hoped that this frank discussion of recommended calibration techniques can help novice LaModel user develop better models and can initiate a discussion among rock mechanics experts on how to improve upon the presented techniques.

Jan 1, 2008

By Dennis Dolinar

In this National Institute for Occupational Safety and Health (NIOSH) investigation, numerical modeling is used to evaluate the degree the pillar strength is increased with a rectangular pillar over a square pillar. Three-dimensional models are developed with pillar sizes and geometries typical of underground limestone mines in the United States. Physical properties for the models are based on geotechnical surveys of nearly 30 underground limestone mines. To examine the effects of pillar length on pillar strength with the modeling, a parametric study was conducted where the pillar width was held constant while the length and height were varied resulting in width-to-height ratios ranging from 0.5 to 1.5 and width to length ratios ranging from 1 to 6. There are two aspects to pillar strength and failure. At relatively low stresses, pillars can fail as a result of geologic structure. At greater depths and sufficient extraction ratios, the pillars can also fail as a result of the vertical stresses exceeding the pillar strength. The effects of increasing pillar length regarding both strength aspects are presented in this study. Equations were developed for the increase in pillar strength with both height and length based on the model results. The results from these equations were compared to those from previously developed empirical equations for rectangular pillars. For the more slender limestone pillars with a width-to-height ratio below one, there is little increase in pillar strength for length-to-width ratios above 2 and almost no increase with length for a width-to-height ratio of 0.5. Only with the more squat pillars is there a significant improvement in strength with length. The gain in pillar strength with length for the pillars is explained by the change in the ratio of the area of the pillar affected by the ends to the area of the pillar. For the squattest pillar, the change in strength is also affected by an increase in pillar confinement along the central length of the pillar as the pillar transitions from a square to a long rectangular pillar. With geologic structure, added pillar length can significantly improve the pillar strength, depending on the strike of that structure with respect to the long pillar axis.

Jan 1, 2007

By Anthony Iannacchione

A Major Hazard Risk Assessment (MHRA) was developed in Australia after a series of mine disasters in the 1990?s. A MHRA is used to help prevent major hazards, i.e. fire, explosion, wind-blast, outbursts, spontaneous combustion, roof instability and chemical and hazardous substances, from injuring miners. A MHRA is a structured process that identifies the characteristics of major hazards, assesses and ranks the risk they present, and evaluates engineering and administrative controls to mitigate them. These controls typically consists of a broad spectrum of prevention, monitoring, first response, and emergency response techniques and helps to move an operation from a reactive to a proactive approach towards safety. This paper documents a MHRA performed at an underground mine where strata instabilities and fire hazards may threaten the condition of its escapeways. The objective of this MHRA is to 1) identify what hazards could affect the egress through the mine?s escapeways, 2) determine what unwanted events pose the greatest threat for the mine, and 3) recommend a plan to prevent or recover from the potential disruption of egress through the escapeway. The plan provides information on the key existing controls that should be monitored and audited, and makes recommendation of new potential controls to further reduce related risks. By documenting the use of MHRA to this specific ground control issue, this paper provides a framework for others to judge the merits of this approach and to help design and perform these activities.

Jan 1, 2007

By Peter (Yunqing) Zhang

Longwall recovery under weak roof conditions could have considerable delay if the immediate roof is weak and deteriorates during screening. A pre-driven longwall recovery room is a feasible solution to minimize the impact of longwall move on production. In this longwall recovery project, a 16-ft recovery room was pre-driven to cover screening, and the shearer cut another 16 ft outby to reach the final recovery line. The pre-driven recovery room was carefully monitored as the face was approaching it. The longwall face operated very well as it cut into the recovery room. The recovery process took about 13 days, and considerable time was saved compared with the previous panel. The support in pre-driven recovery room was designed to handle both front abutment pressure and weak immediate roof conditions. Pumpable standing support was used to support the cantilevered roof as the fender pillar narrowed and collapsed when the face cut into the recovery room. To ensure the stability of the recovery room, 3-D computer modeling was used to evaluate the support system. Abutment pressure, critical fender pillar width, bolting system, pumpable cribs and shield support were considered in the model. The recovery room was carefully monitored during longwall recovery. Roof-to-floor convergence and crib convergence were recorded every shift as the longwall face was approaching the recovery room. Roof, floor and pillar activities and crib performance were also observed as the face cut into the recovery room. This paper presents the support design for the recovery room, evaluation of the support system through computer modeling, and details of the monitoring results.

Jan 1, 2006

By Mike Amick

As virgin coal reserves dwindle, more and more mines are being opened in areas with previous mining. As addressed in this conference before, there are solutions available for designing mines extracting coal from reserves with known underground workings above or below the target seam. Often times, however, mining begins with limited knowledge of the underground workings. Even with careful planning, the proposed design has limited success because the ?facts? as presented during planning turn out not to be as accurate as one would like. At National Coal?s Mine #14, mining the Walnut Mountain seam, after driving the main entries in some 34 crosscuts, it was found during routine mine examinations that the pillars had separated from the roof in a few areas of the mains. Immediate roof conditions proved to be sound but questions arose concerning the stability of the main roof and floor. Core tests were done to better determine the rock strengths and characteristics. The paper presents the ideology used to tackle the effects of mining over old works in an operating coal mine. This paper discusses the analysis of the symptoms observed and the steps taken to ensure that this pillar separation was caused by the underlying old workings and that the separation was expected and controllable.

Jan 1, 2009

By Karsten Zimmermann

The paper presents a study on the influence of face retreat rate in longwall coal mining on surface subsidence. It shows possibilities to influence dynamic ground movement by using a specific and controlled winning regime. For this, a dynamic stochastic prediction model used by DMT in Germany will be proved and adjusted on the specific character of geology in the Northern Appalachian coal field. Occurring ground movements such as inclination, curvature and deformation can be analyzed under static and dynamic points of view. It is theoretically shown that the face retreat rate has only a small influence on the static deformation values, but directly affects rate and acceleration of subsidence and deformation processes. The study shows that because of low mining depth and high mined thickness, static deformation values have the largest impact to surface objects. This implies that high face retreat rates don?t affect the impact on surface objects.

Jan 1, 2007

By Roland C. Walker

Traditional headed rebar has existed in the mining industry as a ground support product for many years. The head of a rebar bolt is most commonly produced by hot upset die forging. Upset die forging produces a rugged, simple head that performs well. Certain elements of the head must comply with regulatory standards, such as ASTM F432-95, which offers a standard test procedure to ensure quality of the product. The head style produced by all major manufacturers has been optimized to reduce manufacturing costs, provide greater miner safety and provide an excellent performing product. Observations were made in some mines of heads failing under in-situ loading. These observations could not be replicated according to the ASTM testing method. This paper highlights the problem and how a solution was developed. The development includes pictures of in-situ failures from the underground operations, laboratory replication tests indicating how this loading occurs, and then the use of this calibrated test method to validate the new design created.

Jan 1, 2009

By Kazem Oraee

In underground coal mining, particularly room-and-pillar methods, the coal pillars play a significant role in roof stability. If the pillar dimensions are increased, the pillar bearing capacity also increases, but more coal remains in the pillar and therefore the recovery of mining operation decreases. Therefore, determining the optimum pillar dimension based on technical, economical and performance parameters is important. In this paper, the coal pillar is designed by using the concept of ground reaction curve (GRC). For this purpose, the GRC for coal pillars is drawn and then the elastic and plastic zone of coal pillar behavior is determined. Based on elastic and plastic zone, different equations are presented to draw a pillar reaction curve and the process of coal pillar design based on GRC is explained. As a case study, this new technique is applied to study the coal pillar state in Tabas coal mine of Iran. The results show that the presented new approach is successfully used in the design of the optimum coal pillar dimensions, and also determines the elastic and plastic behavior limit, which is important especially for the logical design of yield pillars.

Jan 1, 2009

By Daniel Su

Approximately 90% of the primary roof bolts used in CONSOL?s Pittsburgh seam coal mines is 2-piece, 8-foot long, 7/8? (or ¾?), high-strength, resin assisted, mechanical shell tensioned bolt. The remaining 10% is the 2-piece, 8-foot long, 7/8? combination bolt, which employs 4 feet of fast resin to anchor the deformed rebar at the top of the hole. In either system, a 1-3/8? hole is required to accommodate the mechanical shell and the coupler. The cheaper torque-tension rebar system, which is typically fully-grouted with 2-speed resin and which typically provides low bolt tension, is not used in CONSOL?s Pittsburgh seam mines. Rather, it is used in CONSOL?s Central Appalachia mines, where the roof rocks have CMRR rating of 50 or higher. Fully-grouted headed rebars, on the other hand, are used in CONSOL?s room-and-pillar mines. The selection of tensioned versus non-tensioned, fully-grouted bolts for coal mine primary roof support has been debated for the past thirty years. Many researches have been conducted to understand the theoretical bases behind the two systems. This paper describes CONSOL?s experience of using a new fully-grouted, mechanical shell tensioned bolt in the Pittsburgh seam with the development of low insertion force resin.

Jan 1, 2007

By Vincent Scovazzo

This paper compares the two most common pillar design equations used worldwide by John T. Boyd Company; the Mark-Bieniawski Equation, an empirical approach, and the Wilson Equation, an analytical approach. The equations are compared in two ways; by their stress profiles and by the Mark-Bieniawski Equation stability factor. Contrasting the two equations based on the visual comparison of their stress profiles is straight forward but evaluating their resulting pillar designs is problematic. Complications arise due to the differences between the use and development of stability factors for empirical equations and safety factors for analytical equations. To work around these differences, comparisons are made between the two equations by first calculating pillar sizes using the Wilson Equation and then determining the Mark-Bieniawski Equation stability factor for these pillars. Pillars designed using the Wilson Equation were based on site-specific data from 23 mines located in the Americas and Australia. Comparing sizes of pillars designed by the Wilson Equation to the Mark-Bieniawski Equation; the Wilson Equation pillar sizes were smaller in 77% of the cases, similar in 3%, and larger in 20% of the cases.

Jan 1, 2008

By D. S. Choi

This paper describes an improved source location technique for microseismic events related to coal mining. A system of non- linear distance equations is solved with the use of the Newton-Raphson method. This computational method is- advantageous when the number of geophones is limited. In addition, this paper includes the results of the analysis of data from several instruments which characterize both mine seismicity and environmental noise such as vehicle traffic. Analysis of the mine seismicity has contributed to a better understanding of caving above a longwall gob and of what constitutes stable ground conditions.

Jan 1, 1990

By Stephen J. Harven

Geologic conditions in eight northern operating sections of Jane Mine, Keystone Coal Mining Complex. Armstrong County, Pennsylvania are defined by utilizing drillhole data and underground geologic mapping. Three of the eight sections are experiencing difficult mining conditions in the Shelocta "0" coal seam (formerly the Lower Freeport). The five remaining productive sections will exhaust their reserves within one year. Coordinating mine planning with future production levels is aided by indicating areas that appear favorable and lack the geologic conditions that cause difficult mining. Roof rock 1 ithologies, lithologic variations in and below the floor, jointing, overburden thickness, coal splits, paleochannels. and clay veins are the principal geologic factors believed to influence mining conditions in Jane Mine. Careful definition of each cause allows for a reasonable assessment of future mining conditions.

Jan 1, 1987

By Paul Singh

Blasting is an integral part of mining activity and is an inherently destructive process. The quality of the rock mass in which an excavation is being driven has a strong influence on the level of dynamic forces to which the rock can be subjected and sustain damage. Though each specific rock mass occurrence is unique, yet there are common rock mass features which influence the outcome of controlled blasting in a similar way. A field study was conducted which involved assessment of blast damage at several operating mines and blasting of small scale models. The effects of block size and strength, joint parameters, ground water, weathering of rocks and rock mass rating on the results of controlled blasting have been investigated and discussed in this study. The influence of number and thickness of weak layers on overbreak control has been discussed in the light of practical data. Critical particle velocity ranges for damage to rock masses with different qualities have been outlined. An approach for the judicious design of perimeter hole pattern and charge concentration has been proposed.

Jan 1, 2007

By Joe F. T. Agapito

High stresses and adverse geology in deep coal mines in the state of Utah, USA, have caused numerous bumps. The larger bumps have been associated with seismic events with Richter magnitudes of 3.6 and greater, and in some cases have filled openings for lengths of 150 m. A better understanding of the mechanisms and stress levels involved in bumping is needed to help develop improved stress control design and bump mitigation methods. The geology of the area is notoriously bump-prone. The coal has poorly developed cleating and occurs in multiple seams that are often bounded by very strong roof and floor sandstone/siltstone beds. The overburden is formed by thick, competent strata with numerous sandstone channels This geology and deep cover are the major source of high stresses, causing bumps. This paper evaluates live common stress factors responsible for bump problems: depth, sandstone channels, arching, faults, and coal thickness. It uses ease study data from longwall panels with two-entry/yield pillar systems typical of deeper Utah mines. Results illustrate the importance of analyzing stress factor experience to allow a better understanding of the problem.

Jan 1, 2000

By Michael Gauna, Christopher Mark

"For decades, pillar recovery accounted for a quarter of all roof fall fatalities in underground coal mines. Studies showed that a miner on a pillar recovery section was at least three times more likely to be killed by a roof fall than other coal miners. Since 2007, however, there has been just one fatal roof fall on a pillar line. This paper describes the process that resulted in this historic achievement. It covers both the key research findings and the ways in which those insights, beginning in the early 2000s, were implemented in mining practice.One key finding was that safe pillar recovery requires both global and local stability. Global stability is addressed primarily through proper pillar design, and became a major focus after the 2007 Crandall Canyon mine disaster. But the most significant improvements resulted from detailed studies that showed that local stability, defined as roof control in the immediate work area, could be achieved with three interventions:• Leaving an engineered final stump, rather than extracting the entire pillar;• Enhancing roof bolt support, particularly in intersections, and• Increasing the use of Mobile Roof Supports (MRS)A final component was an emphasis on better management of pillar recovery operations. This included a focus on worker positioning, as well as on the pillar and lift sequences, MRS operations, and hazard identification. As retreat mines have incorporated these elements into their Roof Control Plans, it has become clear that pillar recovery is not ""inherently unsafe.""The paper concludes with a discussion of the challenges that remain, including the problems of rib falls and coal bursts.INTRODUCTIONPillar recovery has always been an integral part of underground coal mining in the US. When room-and-pillar methods are employed, large blocks of coal in the form of pillars are initially left in place to support the weight of the overburden. Unless these pillars are subsequently recovered, the coal they contain will never be mined."

Jan 1, 2016

By John H. Perry

Strata III is a full-spectrum roof control system which provides the mine operator the ability to upgrade his roof control in place. The procedure is easily adaptable with current roof bolting techniques. To use the system, the operator starts by installing a special hollow core mechanically anchored roof belt during the roof bolting cycle. This bolt can be upgraded to a fully grouted tensioned rebar bolt by injecting StrataGee G-300, a special polyurethane grout, around the bolt through an injection port in the roof plate. This same bolt can then be used to inject RokLok binders for roof consolidation by pumping the binders through the core of the bolt. This concept in roof control was developed to provide the mine operator a flexible way to maintain roof control in areas which deteriorate over time, or must be kept open for long periods of time. Possible locations of use would be: longwall set-up rooms, recovery rooms, headgates, intersections, and belt entries.

Jan 1, 1987

By Russell Frith

For many years, underground rock mechanics and in particular, roadway/tunnel roof stability has been underpinned by the often unchallenged assumption that roof strength (as defined by the UCS) and stiffness (E) are key stability controls. This has logically led to the proliferation of laboratory testing of rock specimens and the development of indirect geophysical methods to gain estimates of these two rock parameters. Furthermore, many design methods are significantly focussed on replicating rock mass behaviour through either intact or failed constitutive models. Demonstrably the strength and stiffness of the host rock material is commonly used as one of the key indicators of excavation roof stability and it finds either direct or indirect use in just about every rock mass rating system in use today. In more recent times there has been a common move to consider and apply (even if only conceptually at the current time) structural engineering type principles (e.g. buckling) to coal mine roadway roof (and rib) stability. Similarly our knowledge of the in situ stress environment and its likely origins has improved significantly, largely through stress measurements and subsequent analysis. This paper combines knowledge in both of these fundamental areas through a deterministic model for roadway roof stability and in combination with field examples, reaches the almost certainly controversial conclusion that UCS and E are commonly irrelevant, albeit that the former may provide an indication of other relevant geotechnical parameters (e.g. bedding cohesion). As with all hypotheses or rules, there are naturally exceptions and in this case, the most obvious is the tailgate of the longwall panel (with adjacent goaf). Due to the significant change in the strata loading environment of a longwall tailgate as compared to first workings for example, the stability equation materially changes so that UCS and E become critical controls. The point of the paper is to present a different perspective on a traditional mining problem and to challenge geotechnical professionals to keep thinking ?outside of the square? in the never-ending endeavour to improve our understanding of the engineering problems we regularly face. Such an understanding impacts upon such issues as geotechnical data collection from borecore, support hardware requirements and design capabilities. Therefore making the assumption that our understanding is always fundamentally correct could in fact be limiting the development of new and improved engineering in the future.

Jan 1, 2006

By Carl Tom Blevins

Resin was first introduced to U. S. mines in 1971 and first produced in 1973. The original polyester roof bolt resin was very expensive and limited to a single cartridge size and a single slow gel time. Early resin applications were limited to very difficult ground conditions. Today approximately 80% of the over 100 million roof bolts installed in U.S. mines, tunnels, and construction projects employ polyester roof bolt resin. The industry has evolved from hand packing samples for trial testing to producing enough resin, if converted to a .9 inch (22.9mm) diameter cartridge, to encircle the world at the equator approximately three (3) times each year. Manufacturing and design improvements allow for a more consistent product with a wide range of applications at a price that is approximately 30% below our 1974 sales price. An inflation adjusted dollar buys six (6) times more resin in 2006 than in 1974. Modern gel times range from a few seconds to over 15 minutes. Viscosity is matched to bolt type and drilling machine characteristics. Multiple cartridge diameters and a wide range of cartridge lengths are offered by two operating companies. Resin manufacturers have also gone through a period of restructuring and change to meet the challenges of the mining industry. DuPont Fasloc has become Fasloc, Inc., a stand-alone company. Celtite became Fosroc then Minova, as it is known today. During this transformation, several manufacturers have either discontinued production or were absorbed. The industry led the development of the chemical grouting materials specifications contained in ASTM F432-95, Standard Specifications for Roof and Rock Bolts and Accessories. A history of the industry will be presented within a discussion of the evolution of the strength index, speed index, cartridge volume, class designation, and product marking requirements of ASTM F432-95.

Jan 1, 2006

By Greg Hendon

Various methods have been used to evaluate the effectiveness of shields in place. The most common method used is static recording of leg pressures by visually examining pressure gauges. In an effort to more closely examine the shield cycle and therefore the shield effectiveness, Jim Walter Resources has implemented a program of monitoring utilizing a polycorder system which is capable of recording convergence and pressure measurements on a continuous basis. This paper will discuss two longwall panels at Jim Walter Resources which have been monitored.

Jan 1, 1990

By Ke Yang

In Chinese coal mines, extraction of deep, highly gassy soft coal seams sandwiched between soft floor and soft roof in complicated geology is commonly encountered. How to safely and efficiently excavate such seams is a very significant and important problem. It has been a focused research area in recent years. By combining the characteristics of fully mechanized longwall mining methods such as large cutting height and mining along the dip, an integrated method and technologies for the Zhangji Coal Mine were developed. This technology includes the design of a complicated geological exploration system, optimization of mining method and working face parameters, control of rock pressure and high levels of gas, reliability model of the production system, and selection and compatibility of equipment. Engineering practice shows that the integrated technology was successful in mining these complicated seams. This study not only enriches the mining method, but also improves the coal mining practice, especially ensuring both safety and productivity under complicated geological conditions.

Jan 1, 2009