Search Documents

By A. J. Kwitowski

Remote control for mining machines ordinarily means the operator is not seated on the machine, but is located within direct view of the machine and work area Thus, remote control operators are exposed to the hazards of roof/rib falls and dust/methane explosions. The U.S. Bureau of Mines has developed a method to disassociate remote operators from these hazards. Off-board, computer-based "tele-operational" systems are utilized that station the operators one-hundred meters or more distant from the working faces. Details are provided for tele-operated systems for thin-seam extraction and haulage equipment in highwall and deep, room-and-pillar coal mines.

Jan 1, 1992

By A. S. Trimble, J. C. Hower

The petrographic composition of sized coal produced through the progressive grinding of a Central Appalachian high-volatile bituminous coal blend was analyzed for multiple sets either by removing fine, -200-mesh, coal after each test iteration or by retaining the fine coal in progressive test fractions. With prolonged grinding, coarser fractions tend to become depleted in vitrinite and vitrinite-rich microl ithotypes, leading to progressively harder-to-grind coal remaining in the oversize, +200-mesh, fractions. The latter trend is shown both by the maceral and microlithotype composition of the coal and by the increased slope and fractal dimension of size frequency distribution, implying an increase in hardness and resistance to grinding of the oversize coal.

Jan 1, 2000

By A. E. Reisenauer, R. W. Nelson, G. W. Gee

A model assessment was made to evaluate contaminant transport to ground water from clay-lined and unlined tailings pits. The input hydrologic soil characteristics were measured on materials typical of those found at the Morton Ranch uranium mill site in central Wyoming. The assessment involved combined saturated and partially saturated flow and contaminant transport models for two-dimensional cross-sections typical of the proposed Morton Ranch burial pits. Specifically obtained from the models were contaminant flow paths, the advancing contaminant flow fronts for sorbed and non-sorbed constituents, and travel times of contaminants along flow paths. Such results enable evaluation of the environmental consequences for the alternative control methods.

Jan 1, 1980

By Douglas W. Fuerstenau

This paper concern the specific adsorption of sulfate anions on nonmetallic minerals and its role in flotation. The specific surface affinity of sulfate ions in various systems has been observed in the results of electrokinetic measurements that show conditions under which sodium sulfate can reverse the sign of the zeta potential. The electrical double layer model provides a means for interpreting the results and for estimating the free energy of adsorption of sulfate ions. Because of their surface activity, sulfate ions not only can function as a depressant in the flotation of oxide minerals with physisorbed anionic collectors but also can function as an activator for flotation with physisorbed cationic collectors. Their role in depressing or enhancing the flotation of the sparingly-soluble mineral barite is also explained in terms of the double layer model.

Jan 1, 2005

By Jean-Michel Rendu

The semivariogram is one of the most important tools available to the geostatistician for the analysis of mineral deposits. To be complete, a semivariogram study must include a minimum of three parts which are highly interdependent. These are: calculation of the semivariogram, mathematical modeling, and geologic interpretation. The known factors and conditions which controlled or influenced the distribution of mineralization within the body being studied should be considered in the analysis .of the semivariogram. The presence and characteristics of successive phases of mineralization, the chemical and physical properties of the host rocks and the mineralization should all be considered. This requires close and continued communication between the geologist and the geostatistician prior to and during the semi-variogram study. Geologic stationarity is needed if meaningful semivariogram results are to be obtained. The first step is, therefore, to determine whether the mineralization can be analyzed as a whole or if different geologically homogeneous sections must be defined and evaluated separately. Different methods can be used to calculate an experimental semivariogram from known sample values. The method chosen will depend not only on the anticipated and actual statistical properties of the deposit, but also on its geologic characteristics.

Jan 1, 1982

A number of factors have resulted in the widespread use of computer simulation as a day to day tool in the mineral processing industry, as is the case in most engineering disciplines. A number of simulation packages, both steady-state and dynamic are now available commercially. The developers of such software face an enormous challenge in maintaining and improving the packages due to the complexity inherent in such systems. This problem known as the software crisis faces all developers of complex software. Object-oriented (OOP) and design is a methodology which has been developed to try and minimise this problem. The use of the OOP paradigm in the devlopment of simulation software for mineral processing systems is explored in this paper and it is found that OOP techniques have major benefits for the design and development of such software.

Jan 1, 1992

By J. F. Stenebråten, W. P. Johnson

Carbonaceous material (CM) from the Barrick Goldstrike Mines, NV, was characterized with respect to its gold sorption (preg-robbing) and gold recovery behavior. The breadth of graphite peaks measured by X-ray diffraction were used to calculate crystallite dimensions (002) of the CM. The (002) dimension was found to vary inversely with preg-robbing activity and directly with gold-recovery behavior, indicating that the degree of graphitization (maturation) experienced by the carbonaceous material is correlated with gold-loss during ore processing. The inverse correlation of preg-robbing activity was improved when percent preg-robbing was regressed against (002) crystallite size and carbon content. The (101) crystallite dimensions of all samples were calculated from laser Raman analysis, and were not found to correlate with preg-robbing behavior of the CM. BET surface area and micropore size distribution results were affected by grinding history, negating comparison of these characteristics between samples.

Jan 1, 2000

By D. S. Holmes

Biological processes for metal solubilization and ore beneficiation are in widespread use today. There are also some promising new applications of biotechnology in the areas of metal concentration and toxic metal cleanup. Recent progress in genetic engineering promises both to revolutionize the existing biological process and to expedite the adoption of the new biological applications. But before it can do so effectively, progress must be made in many areas of fundamental research and in biochemical engineering. These issues are addressed with special reference to the biotechnology of semi-enclosed containers (bioreactors), dumps, heaps, in situ and under- ground leaching, and with respect to the biotechnology of metal concentration. Finally, certain biological considerations for bacterial strain improvement are discussed.

Jan 1, 1987

By K. Hanumantha Rao, K. S. E. Forssberg, F. Su

The influence of reagents dosage, pH, temperature, and particle size on the kinetics of apatite flotation response from magnetite has been investigated. The first-order models characterizing rectangular distribution and fast and slow distributions (F-S model) of floatabilities gave an excellent fit to the results of apatite flotation when compared to other models. However, the latter model is found to be better than the former in the goodness of fit and also in the description of flotation performance. The kinetic parameters in the F-S model are estimated by using a nonlinear least squares fitting program. The ratio of fast and slow rate constants is observed to be an important parameter for identifying the optimum levels of the variables and to outline the selectivity between apatite and magnetite. The influence of collector dosage is realized from the model parameters by relating it to the fraction of slow- floating particles. An attempt has been made to describe the apatite flotation behavior with the determined model parameters.

Jan 1, 1999

The trend in the U.S. coal industry in recent years has been a continuous increase in the percentage of coal produced by surface mining methods. Though the predicted energy demands promise a good market for coal, growing legal and environmental issues make the exploitation of a coal deposit by surface methods a difficult and challenging task. Major emphasis has to be placed on the development of integrated mining and reclamation schemes which enhance the possibilities of post mining land uses. Since no major breakthroughs are foreseen in the near future in surface mining equipment, innovative applications of current equipment must be developed. Draglines have been and are expected to continue as the primary earthmovers in surface mining of coal. A dragline simulation model has been developed which has the capability to analyze various deployment schemes such as conventional side casting, advance benching, and extended benching. The mathematical aspects of the model, the input data, and the output results are discussed with reference to an application in an operating mine. The model can be used to select a suitable dragline for given geological and mining conditions and to study the effect of alternative mining layouts and spoiling plans on machine production.

Jan 1, 1979

By J. W. Shuster

Test of trolley-diesel prime power is another step in the search to exploit the unused potential of electric wheel driven haulage trucks. The output of the present engine - a 700 horsepower diesel - is not adequate to exploit fully the 1200 horsepower potential of the two electric wheel drive motors. Power was supplied to a modified 100-ton haulage truck through a double wire trolley system. The vehicle was tested with various payloads on a 7% adverse grade haul road. More significant conclusions developed are: Power - Horsepower to propel the vehicle can he more than doubled to improve truck cycle time. Productivity - Trolley power up adverse grades can improve [producivity] rates from 18 to 36%, dependent upon haul road profile.

Jan 1, 1968

By J. A. Hrabik

The feasibility of mining deep phosphate deposits by a borehole mining system was compared with mining by proven conventional techniques. An economic comparison of the borehole mining system with conventional dragline and bucket wheel excavator mining systems was completed at various mining depths and production rates. Hypothetical phosphate deposits, with various overburden thicknesses and reserve tonnages, were defined. Geologic conditions necessary for the application of the borehole system were identified. Discounted cash flow analyses based on derived capital and operating costs were used to generate rates of return and product prices. Borehole mining was found to be more economical where overburden thickness was 46 m (150 ft) or greater. However, at 15- and 30-m (50- and 100-ft) thicknesses, conventional surface mining was more economical. Overburden thickness has a great effect on the economic feasibility of the conventional mining systems but less effect on the economics of borehole mining. Economies of scale are only realized in conventional mining, since larger equipment is used to achieve greater production, whereas increased production from borehole mining is achieved using additional equipment units. A comparison of the environmental effects of borehole and conventional surface mining systems showed that borehole mining is environmentally more desirable.

Jan 1, 1987

By R. E. Johnson, J. E. Dutrizac, B. R. Palmer

Silver sulphide (acanthite) and lead sulphide (galena) dissolve relatively rapidly in FeCl3 media with the formation of elemental sulphur and soluble silver and lead chlorides. Parabolic kinetics are observed, and the leaching rates are controlled by the outward diffusion of the AgCl and PbCl2 reaction products through the constantly thickening elemental sulphur layer formed on the sulphide. Hence, both leaching rates are strongly dependent on those variables which affect the solubility of AgCl or PbCl2 at the reaction interface. The rates therefore increase with increasing temperature and total chloride ion concentration, but decrease in the presence of elevated concentrations of AgCl or PbCl2. By contrast, neither sulphide is significantly attacked by ferric sulphate media, even at high Eh values. Although the reasons for the refractory behaviour of Ag2S in sulphate media remain unknown, the low rate of PbS attack is attributable to the passivating layer of PbSO4 and elemental sulphur formed on the surface of the galena.

Jan 1, 1993

By P. James, L. J. Steiner, F. Turin

NIOSH researchers and an industry partner conducted an investigation to study the effectiveness of ergonomic interventions in mining. The study required a significant commitment of time and resources from the cooperating site, Bridger Coal Company. This paper focuses on some of the challenges faced by the researchers and their cooperator. Challenges included the need to redesign methods of identifying and prioritizing injuries, and the need to train the workforce in ergonomics while still maintaining progress and interest in the process. The authors discuss some practical interventions implemented by Bridger Coal to date, and discuss future research implications brought about by PacifiCorp’s Generation Business Unit, who monitored the project to determine whether an employee-owned ergonomic process could be implemented throughout their operations.

Jan 1, 2003

By Ronny J. Sadri

Under contract to the Department of Energy, Fluor Mining & Metals, Inc. and Bonner & Moore Associates developed a group of computer models that can be used to simulate single seam dragline operations. These models have been subsequently modified by Fluor for use in multi-seam dragline mining situations. The single seam model analyzes the digging, spoiling, and walking patterns of draglines to identify possible parameter changes to increase productivity. Parameters such as key-cutting, panel width, digout length, and bench height, etc., are analyzed in this process. The models were tested using data from four operating mines. Field demonstrations were performed to correlate computer optimization results with field data. Productivity was greatly enhanced at one mine site by a change in some of the operating parameters. The multi-seam study has as its objective the development of a broad- based mine planning tool which would be used to identify and quantify the different procedures employed in multi-seam dragline mines to increase their productivity. The major problem identified in multi-seam mining is the sequencing of the different stripping and mining operations. The multi-seam model has the same capabilities as the single seam model. In addition, it models up to four seams with three partings per seam. It allows the operation of several draglines at different levels, and analyzes the effect of ramps, rehandling, and ancillary mining equipment.

Jan 1, 1982

By W. A. Cincilla, S. C. Tadolini

INTRODUCTION Resin bolting systems continue to gain popularity in underground coal mines in the United States, and their general success under a wide range of geological and operational conditions is well documented. In 1984, 36% of all bolts used were resin-grouted systems. However, many questions dealing with basic support mechanisms and the influence of various factors on bolt effectiveness in situ remain only partially answered. The Bureau of Mines' Denver Research Center conducted a major research project to investigate the influence of installation procedures on the effectiveness of resin-grouted roof bolts. The project consisted of two main studies: the first dealing with the contribution of bearing plates to the load-carrying capability of the bolt; the second examining the relationship between installed grout column and the anchorage capacity as measured by the standard pull-out test. Additionally, a finite-element computer model and other analytical and empirical techniques were applied to aid in the basic understanding of the test procedures and to examine the load transfer mechanism in resin-grouted bolts, which to date has not been comprehensively assessed. The plate study includes field test results from two mines (Fig. 1). At these test sites two behavioral parameters were measured: the actual loads that bearing plates were subjected to when installed in conjunction with full-column resin grouted bolts, and the roof movements generated by the applied loads. Results indicate that bearing plates are subjected to varying degrees of loading, which range from conventional installation pressures of 2.2 kN (500 lb), up to a measured load of 142.4 kN (32,000 lb) when the immediate roof is shifting and deforming. These measured loads indicate that the bearing plate is an integral part of the support system. Differential sag stations, installed to monitor roof displacements in the test sites, show the highest degrees of loading occur in conjunction with the largest amounts of movement. The column-length study addresses possible reductions in anchorage capacity of "full column" bolts. These reductions could result from such factors as the loss of grout to surrounding strata, or improper mixing of catalyst and resin. Field test sites were established at eleven mines located in major coal mining districts throughout the United States (Fig. 1). Four major roof-rock types were represented in the study: shale,

Jan 1, 1986

By H. H. Murray

Abstract. World reserves of bauxite are abundant. Domestic reserves are limited and as a consequence the United States must rely on foreign suppliers for over 90 percent of its bauxite. Nationalization of many bauxite mining operations, levying of higher taxes, increased production and transportation costs, and attempts to create a uniform market price combined to place the United States in a vulnerable position. Alumina from kaolin, alunite, anorthosite, and oil shale have-been-or are being evaluated. World bauxite reserves are increasing and attempts to establish a uniform price have failed; therefore, it may be many years before domestic non-bauxite sources of alumina can compete with imported foreign bauxite.

Jan 1, 1980

By Donald A. Dahlstrom

INTRODUCTION Solid-liquid separation is an important and many times a critical step (or steps) in a mineral or coal processing plant. Some examples of typical critical separations are as follows: 1. Operating a seven to eight stage CCD thickening circuit to re¬cover almost all of the caustic and alumina trihydrate values in an alumina plant. This must be accomplished with highly scaling slurries, starting temperatures of over 100°C and operate on a closed circuit system. 2. Making a filter step operate to produce a proper moisture for the balling step so that the pellet furnace can produce a proper product. Bentonite addition must be minimized and a good quality filtrate must be maintained to prevent abrasion of the internal parts of the filter. 3. Operating a closed water system in a coal washing plant so that reclaimed water containing less than one percent suspended solids is produced for reuse to maintain beneficiation ef¬ficiency. Refuse solids must also be thickened so that they can be effectively dewatered to meet state disposal requirements. 4. Recovering phosphoric acid values from a slurry containing gypsum and other gangue solids at an elevated temperature. This must be done while minimizing wash water and maximizing P2O5 re¬covery while simultaneously minimizing scale problems. While solid-liquid separations are important to overall performance in the processing plant flowsheet, it is also a significant factor in plant costs. Capital and operating costs for all the solid-liquid separation steps (includ¬ing water reclamation for reuse) in such plants are probably between 10 and 20%. Energy consumption can also be important in these separations. For example, in the copper concentrator, it is the third largest category in energy consumption, after comminution and flotation. Obviously, solid-liquid separation steps in a plant demand proper atten¬tion in design in order to achieve both optimum performance and cost. Simultaneously, knowledge of funda¬mentals are important to improve results in existing plants.

Jan 1, 1986

By G. Baudet, M. Save

Ethoxylated phosphoric ester surfactants were evaluated as collectors for flotation of carbonates from sedimentary phosphate ores, at slightly acidic pulp pH, using sulfuric acid or sodium fluorosilicate as a phosphate depressant. With 12 to 15 carbon atoms in the hydrophobic chain, maximum collecting power was observed for 9 to 10 ethylene oxide units. Only fine carbonates, ranging in size from about 20 to 160 µm or 40 to 200 µm, were effectively removed with phosphoric ester collectors. Utilization of seawater, or water of extremely high hardness, did not detrimentally affect selectivity. Silica, silicates, and residual fine carbonates can be separated in a second flotation stage, with primary amine as a collector. Coarse carbonates are separated by direct flotation of phosphate with fluoride ion as a phosphate activator and primary amine as a collector. In a seawater pulp, fluoride ion was not required. Typical examples of laboratory and pilot- scale test results are given to illustrate capabilities of the various flotation flowsheets.

Jan 1, 1999

By I. K. Kapageridis

Environmental management and planning requires the integration of large volumes of disparate information from many sources and the analysis of this information with efficient tools for assessment and evaluation. Effective methods of communication that allow interactive participation in the planning, assessment and decision-making processes are also very important. The VULCAN software package from Maptek (Pty) Ltd comprises a large number of 3D graphical tools within an interactive 3D interface called ENVISAGE. These tools are designed and developed to help engineers and scientists to identify and solve environmental problems. The combination of VULCAN 3D Software and the I-SiTE 3D Laser Imaging system leads to powerful solutions for environmental management. This paper presents the capabilities of this integrated system and its applications for environmental management.

Jan 1, 2002