Search Documents

By Peter McKenna

Different reefs being extracted from a mine will, in all likelihood, have significantly different semi-variogram models - and these will probably vary from geozone to geozone. As errors of estimation are dependent on the semi- variogram parameters, it follows, if a mine samples all reefs in all sections using the same sampling grid pattern, that estimation errors (or limits of confidence) will not be the same throughout the mine. This may be an undesirable situation! A geostatistical study of the relative merits of alternative sampling arrangements has been carried out by considering different reefs in different sections of a South African gold mine.

Jan 1, 1989

By Y. Numata

2-Mercaptobenzothiazole (MBT) is a heterocyclic-mercaptan and belongs to a group of molecules containing nitrogen and sulfur as electron donor atoms. MBT has been employed as a collector in flotation under names of MBT, Captax, and Flotagen. It is a major constituent of reagents in the 400 series of the American Cyanamid Co. Current applications of the reagent include flotation of copper minerals, tarnished or oxidized lead, copper activated sphalerite, and nickel ores. It has been used successfully in the flotation of pyrite in acid circuits in the range of 4 to 5.

Jan 1, 1990

By M. D. Lawton

Anglo-Rouyn Mines Limited, managed by Rio Algom Mines Limited is a subsidiary of the British-based Rio Tinto-Zinc Corporation Limited. This mining operation is situated in Northern Saskatchewan, 250 miles north of Saskatoon and represents the first base-metal mine of any importance served by this relatively new mining province. The outcrop of Copper-bearing Chalcopyrite was first discovered by prospectors in 1915, but was not mined until 1965 due to the absence of any form of road into the area prior to this latter date. The mine, mill and concentrator were designed to handle 900 tons per day of comparatively hard, abrasive ore containing chalcopyrite with traces of gold and silver. The flow sheet, Figure 1, is, we believe, elementary, designed with low cost in mind and utilises much old equipment from closed¬-down mines. Due to some difficulty in attaining the designed grinding capacity, changes were made in the crusher circuit. This, unfortunately, lowered the crushing rate too much. A series of changes have taken place to re-establish the original crusher capacity of better than 100 tons per hour. In the quest for a better recovery certain modifications have been tested in the concentrator circuit. These steps are discussed in minor detail.

Jan 1, 1970

By I. Iwasaki

The effects of percent solids, mill loading and grinding time on product size distribution and ball wear were studied in a laboratory ball mill for a taconite ore. Mild steel balls and HCLA steel balls were used to examine the role that ball hardness play in grinding. Net production of minus 325 mesh - material reached maximum at 70% solids, whereas the ball wear decreased as pulp density increased. HCLA steel balls ground the taconite ore finer than mild steel balls under otherwise identical conditions. Examination of ball surfaces with a scanning electron microscope suggested that grinding with mild steel balls involved nipping rather than attrition, whereas grinding with harder HCLA balls involved both nipping and attrition.

Jan 1, 1984

By Boris J. Kochanowsky

In the mobile crushing unit system trucks are replaced by a conveyor resulting in a "continuous" almost "fully-automated" operation with all its attendant advantages. In consequence, overall operating costs are greatly reduced. Because of the new designs of large mobile crushing units that have been brought on-to the market, the use of these plants has increased significantly during the last three years. This paper describes the designs of new mobile crushing units, and emphasizes the advantages that such plants offer to the rock products and mining industries. It examines operating costs, and indicates the conditions in which the application of these plants is most profitable.

Jan 1, 1968

By Dennis K. Mortensen

The warm southwestern desert of Arizona is an ideal location for ASARCO's new Sacaton Unit. The climate of this arid region played a major role in the design considerations of the Unit's crushing and concentrating facilities. Low yearly rainfall and relatively high yearly temperatures are a combination that was taken advantage of when designing the surface facilities. The plantsite, located due west of the mine pit, is in an area originally covered with sparse desert vegetation, underlain to an average depth of 125 feet by desert alluvium. The entire plantsite area slopes gently to the southwest at approximately 1%. Ground conditions at the plantsite area were not acceptable for construction due to the collapsability of the wetted soil when under loaded conditions, Overburden from the pit area was used to form the foundation for the entire plantsite. This waste material, entirely devoid of rock, was placed and compacted to an elevation approximately 20 feet above the desert floor. Elevating the plantsite by filling with waste material not only provided an adequate construction foundation but also eliminated the possibility of flooding from run-off in the surrounding desert areas.

Jan 1, 1974

By Tsunenori Shibata, Kazunori Jimbo, Kaoru Toya, Masafumi Matsumoto, Jinya Mitsui, Toshinori Tsuji

"The Toyama Line is under construction as a natural gas pipeline with a length of 102 km from Itoigawa City to Toyama City. A 2 km-long tunnel section of the pipeline that we are reporting here is being excavated in a mountain area away from an urban area. The geology under which the tunnel is constructed is collapsible fractured breccia slate and Holocene sandy soil. Other tunnels of the Hokuriku Expressway and Hokuriku Shinkansen are in service above the tunnel route. From the starting shaft on Toyama side, conventional tunneling was adopted to facilitate excavating the base rock layer and maintain enough distance from the Hokuriku Expressway tunnel. From the starting shaft on the Itoigawa side, TBM tunneling was adopted to cope with the unconsolidated soft ground for a 200 m-long section from the shaft. We will discuss the issues and countermeasures concerning the selection of a tunnel route and excavation methods, performance of both conventional and TBM tunneling, and underground connecting of these tunnels excavated by conventional (NATM) and TBM methods under a high groundwater pressure up to 1.2 MPa. INTRODUCTION AND BACKGROUND The International Petroleum Exploration Teiseki Co., Ltd. (INPEX) is constructing a high-pressure main pipeline network in the Toyama Prefecture area to promote the use and reliable supply of natural gas as shown in Figure 1. As part of the Toyama line project that has a total length of 102 km, A-1 construction, the nearest section to the tunneling starting point in Itoigawa City, where various tunnel excavation methods have been adopted to install the high-pressure pipeline 20 inches in diameter, a 2 km tunnel in the A-1 construction section discussed here is to be excavated by conventional and TBM methods in a mountain area. Based on environmental studies such as traffic jams due to frequent traffic of heavy vehicles disposing of soil, and the effects of dust, noise and vibration during construction, we selected the route to install the gas pipeline in a mountain area as shown in Figure 2, where the impact on the surrounding environment could be minimized."

Jan 1, 2016

By M. K. Mohanty

A modified coal flotation characterization procedure, referred to as the Advanced Flotation Washability (AFW) technique, has been developed which, compared to traditional procedures, provides a more accurate prediction of the optimum separation performance achievable by a froth flotation process. The AFW procedure uses a vertically-baffled flotation column which provides enhanced selectivity among particles of varying degrees of hydrophobicity due to a plug-flow environment and an improved carrying-capacity environment. In fact, the separation performance of the traditional procedures was enhanced by increasing the possibility of operating under improved selectivity conditions. The separation performance provided by the AFW procedure was superior to that obtained from multiple cleaning stages using commercially-available flotation columns under both kinetic and carrying-capacity limiting conditions.

Jan 1, 1997

By Vas P. Srinivasa

This paper examines the role of the heavy media separator in the mineral industry. Procedures used in selecting the separating vessel, developing the process flowsheet, and designing a heavy media circuit are discussed. For comparative purposes, the capital investment and operating costs of different types of operation are included.

Jan 1, 1981

By Z. Hladysz

It is common to nine a coal seam affected by previous extraction of a coal seam below. As a result of that severe problems may occur during the extraction process. This paper presents the analysis of undermining effects based on field observations. A simplified method for the evaluation of risk in undermining operations is presented and predictions of the degree of possible damages to the undermined coal seam is given.

Jan 1, 1985

By C. L. Peng, F. F. Min, S. X. Song

"Using a parameter representing the degree of hydration of particles in a liquid called hydration index I, which we derived based on Einstein’s viscosity equation, we evaluated the degree of hydration of fine montmorillonite particles in different aqueous solutions by measuring the viscosities of the montmorillonite dispersions and plotting relative viscosity against volume fraction of dry montmorillonite particles in the dispersions. We investigated the effects on the hydration of montmorillonite in aqueous solutions of (1) the type and (2) the concentration of electrolytes in the solutions and (3) pH. For the same concentration of electrolytes, the hydration index I of montmorillonite was found to increase in the order of Na+ > K+ for monovalent cations and Mg2+ > Ca2+ for divalent cations, and to decrease with increasing valence of cations in the order of Na+ > Ca2+ > Al3+. For both Na+ and Ca2+, the hydration index I first increased with increasing concentration of electrolytes and then decreased after a certain concentration. The hydration index I increased with increasing pH. IntroductionClay minerals have the distinctive ability to adsorb water molecules and hydrated cations in aqueous solutions, resulting in hydration on their outer surfaces and in their interlayer spaces. Many investigators (Jurinak, 1963; Anderson and Tice, 1971; Costanzo et al., 1982; Israelachvili, 1992) had found evidence of ice-like structures of water on clay minerals.This phenomenon of hydration plays an important role in the dispersion and sedimentation of clay minerals in aqueous solutions. To understand clay hydration, numerous experimental and simulation studies have been carried out since 1933, including the recent ones of Hawkins and Egelstaff (1980), Skipper et al. (1995), Karaborni et al. (1996), Salles et al. (2013) and Morrow et al. (2013). Among the factors that can influence a clay mineral’s hydration characteristics are chemical composition, type and degree of isomorphous replacement in its structure, and number and nature of associated exchangeable cations."

Jan 1, 2015

By Harold Bloom

Dimethylglyoxime reacts with nickel in a buffered ammonical-citrate solution containing the detergent ?Aquet? and hyroxylamine-hydrochloride. The resulting nickelous dimethylglyoxime is extracted with xylene. Visual comparison with standards permits the estimation of from 50 to 10,000 ppm of nickel. Soil, rock, or sediment may be decomposed by digestion with (1-3) nitric acid, allowing about 70 determinations per man-day to be carried out. With minor modifications to the above procedure, sediment and soil may be semi-quantitatively analyzed for nickel at the sample site. The chemical equipment is easily portable and the analysis extremely rapid because the buffer, dime thylglyoxime and xylene are added simultaneously to the sample and no heating is required. The sensitivity varies with the "availability" of the nickel ions; under favorable conditions, one may obtain a positive test for as little as 10 micrograms in soils and sediments. This procedure is similar to one, for the field determination of heavy metals described elsewhere by the author.

Jan 1, 1958

By Lyle A. Hale

The subject area known as upper Dry Valley is located 15 miles due east of Soda Springs in Sections 14 and 23, Township 9 South, Range 44 East, Caribou County, Idaho. The railroad extending from Soda Springs to its terminus at El Paso's Maybe Canyon mine is 8z miles to the north in lower Dry Valley. Initial data derived from trench work in 1962 revealed a variety of econom¬ically significant alterations of the phosphatic beds related to the rather unique geomorphic development in the northern part of phosphate lease 1-012989. It was apparent that such conditions, while valid for near-surface beds in a strike direction, would be misleading if projected to the proposed depth limits of strip mining. Consequently, a subsurface mapping program was initiated in 1963 to determine: (1) the depth and horizontal extent of weathering and related phe¬nomena, (2) the depth, thickness, and quality of ore beds and intervening strata, and (3) structural geology as a guide for mining procedures. Successful use of a scintillometer in 1956 to detect the subcrop position of phosphate beds in the Smokey Canyon area of southeastern Idaho led to the conclusion that gamma radiation surveys of drill holes could be a useful aid in subsurface mapping. The objectives of this paper are: (1) briefly to describe geologic features characteristic of the phosphate lease area and (2) to demonstrate the practical application and theory behind gamma radiation logging as an effective tool in the economic evaluation of a phosphate lease.

Jan 1, 1969

By K. Baba

Liberation of valuable minerals from a gangue matrix during size reduction of multiphase mineral particles is an important objective in mineral separation processes. A methodology for the prediction of volumetric grade distribution from one dimensional, linear intercept image analysis is being developed using a transformation function to describe the relations hi p between the linear and volumetric grade distributions. As part of this research effort it has been found that a transformation function, derived from Monte Carlo simulations of irregularly shaped particles, mainly depends on the volumetric grade and the dispersion density, i.e., the number of nuclei (or grains) per particle. A possible mathematical form for the transformation function is described in detail.

Jan 1, 1985

By David. C. Hoffman

As you are all well aware, the minerals processing industry and process industries in general are now heavily involved in reassessing their process flowsheets. The topic of concern is the little arrow in one corner of the drawing at the end of the process flow that usually says "to waste." A really startling statement might have said "to waste disposal area," which implied that there was some concern, thought, or measures taken to deal with the waste. Since 1965, the year of the Water Quality Act, many laws have been passed and agencies formed dealing with the multi-faceted area of pollution. One of these laws, the Air Quality Control Act of 1967, was the initiating force in the development of Calcilox additive to help solve the problem of sludge disposal resulting from the scrubbing of SO2 bearing gases. The intent of this paper is to focus in with a wide-angle view on a particular type of waste stream, generally an aqueous, inorganic slurry, and present the reader with an alternate approach to their disposal via Calcilox additive stabilization. Each waste stream is unique and will require different techniques to meet the design objectives. Calcilox additive is not intended to be a panacea for every slurry disposal problem, but, rather a viable alternative that should be investigated before a final waste disposal approach is chosen. This paper will summarize the development of Calcilox additive; briefly discuss stabilization; and most importantly, discuss some applications to develop a feeling for Calcilox additive stabilization. Actual dollar costs will not be presented, for each waste stream differs and the ultimate disposal mode chosen greatly influences the costs.

Jan 1, 1976

By G. T. Lineberry

Reduced clearance is one of the most important characteristics of encumbered space in underground coal mining. Another key variable is the maximum velocity at which a piece of mobile mining equipment can operate in this limited space. Typical velocity- clearance curves for different mine transportation systems are developed and characterized. Applications of the relationships are examined, emphasizing their significance in the design and control of mine materials handling systems.

Jan 1, 1983

By J. Carr

Ring gear and pinions used as the final drive on large metallurgical grinding mills are expected to transmit their rated horsepower reliably for long periods of time. Duty is 24 hrs./ day. Life expectancy of such gear sets is of the order of 20 years; that is, each gear and pinion flank is expected to resist failure by pitting for 10 years. This means that for a dual pinion gear set having a ratio of 18.42:1.0 and a mill speed of 10 RPM, every gear tooth will see 105.12 x 106 surface contact stress cycles and every pinion tooth will see 968.15 x 106 surface contact stress cycles in a 10 year period. The allowable surface contact stress on the gear and pinion is determined by the material hardnesses. The rule being the higher the hardness, the higher the allowable surface contact stress may be.

Jan 1, 1985

By G. Reed Marchant

The control systems engineer is often faced with the problem of designing tests or experiments where the cost of obtaining information is expensive. This is true in aerospace as well as in process industries. In these situations the details of test design should be carefully evaluated before any test is executed so that the maximum amount of information is obtained for the effort expended. In recent years there has been a steady trend towards increased automation, In the process industries this has resulted in extensive review of process variables and, instrumentation techniques, development of more accurate system mathematical models, and extensive investments in complex control system as well as completely automated plants. When planning and developing these systems, where each measure of a process variable is usually expensive, it behooves the design engineer to give considerable thought to the details of test design before instrumentation is procured and installed so that the maximum amount of information can be obtained for the expense incurred.

Jan 1, 1968

By Ralph C. Flow

In Cleveland County, North Carolina, one and one-half miles south of Kings Mountain, Foote Mineral Company operates an open pit for the production of spodumene, feldspar, mica, and commercial stone. Spodumene concentrate is sent to Footers Sunbright, Virginia plant and to other customers. Exton, Pennsylvania and New Johnsonville, Tennessee plants produce lithium compounds sold to the oil industry for multipurpose lithium-base greases, to the metal industry as welding flux, to the air conditioning market, and to the glass industry. Ceramic grade spodumene, feldspar, and mica concentrates go to other processing companies from the Kings Mountain plant. Waste amphibolite is delivered to a neighboring quarry operation.

Jan 1, 1962

By Paul Soros

The Conneaut, Ohio, terminal of the Bessemer & Lake Erie Railroad was the first rail-to-ground-to-water coal terminal on the Great Lakes. Compared to the traditional method of holding coal in railroad cars at the ports for dumping their contents into vessels, it provided for: a. Immediate train turn-around independently of vessel arrivals. b. Winter storage of coal at the port, permitting year round shipment by the mines and year round operation of the railroad.

Jan 1, 1969