Search Documents

By Robert D. Talvensaari

It is indeed an honor for White Pine, as a member of the copper mining industry, to participate in this Rapid Excavation Conference. Although our presentation, as the title indicates, is not a success story, we foresee, through our experience, future application of boring machines and rapid excavation equipment in the hard rock mining industry. One might ask what a copper mining company would be doing with boring machines and why the gamble on a high-cost, capital investment for a relatively untried application. Perhaps a little background on the White Pine mine and its geology will explain our daring and speculative motives. THE WHITE PINE MINE The White Pine Copper Company, a wholly-owned subsidiary of Copper Range Company, operates a mine, mill and smelter at White Pine, Michigan in the western Upper Peninsula approximately 6 miles due south of Lake Superior. We employ approximately 3,000 people from the surrounding area and mine approximately 25,500 tons of low grade (1%) copper ore per day. The orebody is contained within several distinct sedimentary horizons that comprise the lower 20 feet of a Precambrian formation known as the Nonesuch Shale. Numerous articles and reports have described many aspects of the White Pine operation and the geology. I will brief you only on that criteria which precipitated our interest in rapid excavation equipment and techniques, specifically, boring machines. Mineralogical and optical studies have demonstrated that the siltstones, sandstone and shale beds all contain relatively barren and discrete particles of quartz (25%), feldspar and mica, bonded with

Jan 1, 1974

By Donald J. Olson, Thomas J. Lutzenberger, John Ramage

The North Shore Inline Interceptor, Phase IA tunnel is a 8,550-meter (28,000-ft) interceptor tunnel currently being constructed by Traylor Bros./Frontier-Kemper, Joint Venture, using a 9.8-meter (32-ft - 4-in) diameter Robbins tunnel boring machine (TBM). This tunnel is being driven in Silurian age dolomite approximately 91.5 m (300 ft) below ground surface. Significant water inflows were encountered when the tunnel drive penetrated the thinly-bedded Waubakee Formation. Flow increases approaching 0.75 cu m per min per 30 m of tunnel (200 gpm per 100 ft) have occurred in this formation. After driving approximately 2,285 m (7,500 ft) of tunnel (200 m full face in the Waubakee Formation), total flows exceeded 12 cu m per min (3,200 gpm) with about 5.7 cu m per min (1,500 gpm) entering the tun¬nel from the 200 m (600 ft) of exposed Waubakee Formation. Additional water control measures consisting of increased pumping capacity, increased water treatment capacity, surface grouting ahead of the tunnel, grouting ahead of the tunnel face and panning to improve the working environment for installation of tunnel support, were implemented to deal with the large water inflows. Currently (January 24, 1989), 3,400 m (11,000 ft) of tunnel has been driven, total water inflows are in the range of 11.7 cu m per min (3,100 gpm) with only 6.8 cu m per min (1,800 gpm) inflow from about 1,220 m (4,000 ft) of tunnel driven full face through the Waubakee Formation.

Jan 1, 1989

By Claude Bazin, Robert Grant, Mike Cooper

An analysis of the Pb recovery as a function of particle size was carried out for the CuPb rougher bank of a complex sulphide mineral processing plant. Results indicate that higher recovery may be achieved by optimizing the flotation feed size distribution. Simulation of the actual grinding circuit has provided guidelines to modify circuit operating conditions in order to improve product size distribution. Plant tests ar

Jan 1, 1991

By Hayati Karaman, Tevfik Güyagüler

In this paper fires due to spontaneous combustion in Middle Anatolian Lignite mine (OAL) which is the first fully mechanized underground lignite mine in Turkey, are studied. Since the installation of mechanization (1986), due to spontaneous heating, four panel fires namely, A01, A02, A03 and A04 have broken out. During these fires, the concentrations of carbon monoxide, methane and the velocity of air are measured continuously by the Micro Minos Environmental monitoring system. For each fire, the environment where fire has started is examined and the possible causes of the fire are investigated. Also the precautions taken to extinguish the fire at different stages are described and the importance of the early detection of mine fire are discussed together with the limitations of the monitoring system and the practical difficulties observed during the fire.

Jan 1, 1995

By I. C. Lemmer

A distribution-free approach is developed for estimating a bivariate distribution function for an ore deposit in terms of the experimental grade correlogram and experimental "weight functions" of the deposit. These weight functions are calculated as part of the approximation used in the mononodal cutoff concept. Use of this method obviates the need to transform to an isofactorial bivariate model. The method is illustrated for two examples, where the bivariate distributions are supposedly known : (a) the bivariate normal distribution and (b) the bivariate lognormal distribution. It is shown that the estimate of the underlying bivariate distribution is optimal when working at the mononodal cutoff, as can be anticipated theoretically. The approximation decreases in quality on either side of the mononodal cutoff, but still remains acceptable as a first estimate of the actual bivariate distribution.

Jan 1, 1986

By Joel Lenz, Warren Hood, Jackson Jenkins

Whole ore or other process streams are being transported from mines to remote processing facilities for multiple reasons, such as improved project economics, maximum utilization of capital, and minimization of environmental risk. Case studies will be presented from a variety of operations. Glenbrook Nickel processes ore from their deposit and receives ore from New Caledonia, crushes and dries the ore, and transports it inland to the smelter. The Mule Canyon and Rosebud ore bodies truck-haul their ores to the Lone Tree and Twin Creeks processing plants. Pegasus Gold hauls their Diamond Hill ore to their Montana Tunnels facilities, and Sierrita pumps solution to an existing tank house 8 miles away for electrolytic recovery.

Jan 1, 1998

By Mark J. Zdunczyk

Short Mountain Silica mines the Clinch Formation, an orthoquartzite, for silica sand. The operation is located near Mooresburg, TN, about 80 km (50 miles) northeast of Knoxville. Short Mountain is a local geographic name given to an area of resistant sandstone (Fig. 1). The area is part of the Clinch Mountain system that extends from eastern Tennessee to southwestern Virginia. The thick sandstone unit is more technically called a quartz arenite (orthoquartzite) that forms most of the mountain. In 1980, a Knoxville resident brought the Clinch Formation - Short Mountain in particular - to the attention of the large silica-sand producers as a potential silica-sand mine. Working with a local contractor who owned several hundred acres on Short Mountain, the Knoxville resident contacted interested companies. Many silica companies reviewed the property including Ottawa Silica Co., Pennsylvania Glass Sand Co. (both now US Silica Co.),Unimin Corp.,The Morie Co. and others. AFG Industries was the main market for the glass sand product from this potential mine. It had two plants, both within trucking distance from the site. All the silica sand producing companies, however, declined to develop the site. A few years later, Unimin Corp. decided to drill and evaluate the deposit. From that evaluation, Unimin leased the property but later dropped it. The relatively limited market for the Short Mountain product as well as Unimin’s recent acquisition of Carolina Silica were reportedly instrumental in the company’s decision to let go of the lease. Several other companies-unrelated to the silica sand industry - looked at the site but no one was interested in developing it. In 1986, J.D. Nicewonder, owner of coal mines in Virginia and Kentucky, was approached to investigate the site. Nicewonder began to develop the site with the intent to produce glass sand to supply AFG Industries. In May 1988, the first shipment of sand was trucked to AFG Industries.

Jan 1, 1992

By G. R. Marchant

The nonferrous industry has for many years maintained monitoring stations in agricultural areas in the vicinity of smelters to collect data concerning impact of smelter emission on agricultural crop production (Thomas and Cross, 1928). However, in 1967, the United States Congress passed the Clean Air Act which was amended in 1970 (Marchant, et al., 1977). The interpretation of this act by the Environmental Protection Agency (EPA) made it necessary for the industry to install extensive real-time ambient sulfur dioxide (SO,) monitoring systems. This was only the tip of the iceberg. Since that time as a result of additional laws and agency directives, it is now necessary to monitor concentrations of a number of substances -in both air and water. And unless there is a major change in government thinking, this trend will continue during the decade of the eighties. It is difficult to estimate the full impact of these laws. Nevertheless, the impact is large and affects every person in the United States today (Anon., 1972; Rockefeller, 1971; Nelson, Yeager, and Guptill, 1973; and Anon., 1975). It prohibits the burning of trash and paper in most areas of the country. It increases the cost of transportation and the price of motor vehicles. It increases the, cost of nearly everything that is manufactured. In industries which compete in the international market, it reduces their competitive position. In some industries the environmental impact is felt on costs of goods sold in the vicinity of 25% of the total production costs. The major portion of these costs is not due to the monitoring systems but instead is due to the increased cost of production facilities, equipment, and raw materials in industries that are required to comply with environmental regulations.

Jan 1, 1979

By Kang-Hyun Lee, In-Mo Lee, Byung-Kyu Kim, Parkm Jinho, Seoung-Won Lee

"In this study, the TBM Resistivity Prediction (TRP) system is developed for predicting the location, thickness, permittivity ratio and electrical conductivity of anomalous zones ahead of tunnel face using the measured resistivity of the ground. The applicability of the developed system was verified by performing field tests at a construction site in which an EPB-shield TBM is used for tunnelling work. In the first field test, it was found that the rock around the tunnel face had the same resistivity and permittivity with the rock ahead of the tunnel face indicating no anomaly ahead of the tunnel face. In the second test, a stronger zone 5-m thick was predicted ahead of the tunnel face based on lower permittivity than that of the rock around the tunnel face. The ground condition assessed by the newly developed TRP system matched well with that either predicted from geophysical exploration or directly obtained from drilling boreholes or from daily observed muck conditions. INTRODUCTION During tunneling work, the emergence of unpredicted zones of relatively weaker or stronger ground can lead to delays in construction work or an increase of construction cost. Predicting anomalous zones ahead of tunnel face in advance can thus prevent time and economic loss. For these reasons, various methods to predict the ground condition ahead of the tunnel face have been studied and developed. Prediction methods using various kinds of equipment include tunnel seismic prediction, ground penetrating radar, electromagnetic surveys based on electronic antennas, and electrical resistivity surveys conducted by analyzing electric currents in the ground ahead of the tunnel face (Ryu et al. 2008). However, most of the prediction methods are only applicable to conventional tunneling job sites, which feature free access to the tunnel face. In mechanized tunneling projects, accessibility to the tunnel face is very limited because the tunnel face is occupied by the TBM."

Jan 1, 2016

By S. A. Saki, J. F. Brune

"INTRODUCTION Longwall coal mining leaves large areas where the coal has been made removed and the roof rock strata collapse, forming a zone of broken rock rubble called the gob. Figure 1 shows a typical longwall gob area along with the gate roads. The ventilation pattern for progressively sealed longwall panels follows a simple “U” pattern where fresh air is coursed inby to the headgate, flows along the face and exhausts through the outby tailgate as shown in figure 1(a). An important variation of this pattern is the back return (BR) arrangement where the exhaust air from the face is drawn inby and around the nearest open cross cut before it turns in the outby direction towards the exhaust fan. Figure 1(b) illustrates the use of back return. This arrangement moves the point of low pressure from the tailgate corner up to 60 m inby and thus maintains fresh air in the tailgate region that could otherwise be contaminated with gob air.The gob area may contain remnants of unmined coal or parts of overlying coal beds that continue to release methane, eventually filling the gob area with methane in concentrations far above the explosive range of about 4.5 to 15%. Many gob areas must be equipped with gob ventilation boreholes (GVBs) to extract methane, and GVBs often exhaust methane at concentrations from 50% to 90% (Saki, 2016). Due to oxidation processes occurring in the gob, the oxygen content is reduced to a low level, with nitrogen and CO2 making up the major remaining components of the gob atmosphere. FORMATION OF EXPLOSIVE GAS ZONES IN GOBS Since the longwall face area is ventilated with fresh air below 1% methane and the face and gob areas are not separated, an explosive fringe will form where the methane content lies within the explosive range and oxygen content remains above 12%. Figure 2 shows a typical development of such an EGZ. This figure is based on a computational fluid dynamics (CFD) model developed by CSM researchers to analyze gas concentrations and flow patterns in longwall mining. Figure 2(a) shows the formation of EGZ in the gob with a U type ventilation scheme, where EGZ lies right behind the shields in the tailgate corner. Figure 2(b) shows the formation of EGZ in the gob combining U type ventilation scheme with BR, where EGZ is pushed away from the face deep into the gob. The CFD modeling parameters and boundary conditions have been verified with field data from two cooperating, active longwall mines (see Worrall 2012, Marts 2015, Gilmore 2015 and Saki 2016). Other mine geometries, methane inflow rates and gob permeability distributions can be modeled to establish representative gob atmospheric conditions. Two GVBs were operating in the model, extracting 0.165 m3/sec each. The methane in the working areas and returns was kept below 1%. Methane flowing into the model from a rider coal bed above the mined seam was at the rate of 0.55 m3/sec."

Jan 1, 2017

By E. Koufetzis

Rock mass classification systems are core elements of tunneling and empirical mine design worldwide. The Bauxite division of S&B Industrial Minerals S.A. decided to implement a rock mass classification system in order to provide mining engineers and supervisors of the underground mines, with guidelines of stability performance and with a complementary tool for the selection of the appropriate tunnel support. The back analysis system employed is based on visual observation of especially selected underground mine sites, representative of all rock types. This fact combined with the failure or success of the already existing support system, constitute the fundamental part of the work undertaken. The paper is divided into three main parts. In the first part the classification methods of Q, RMR89 and GSI are presented and the advantages and disadvantages of each method in connection with underground mining are indicated. RMR89 and GSI are conclusively selected for use, the main criteria for the selection being, the simplicity in use and the competency of the support system suggested for each rock mass category. The second part points out the methodology for measurements, the practical difficulties encountered during this process and the guiding principles followed, in order to avoid these problems. In the third part, the final conclusion of this project is demonstrated and the different rock mass categories are presented with their relative support recommendations, as they were applied and tested in all phases of the bauxite mines? exploitation. The generated methodology is being implemented by the site mining engineers, for validation and potential improvement.

Jan 1, 2008

By Shinya Ono, Tsuyoshi Katoh, Yuusaku Tominaga

In order to monitor/control airflow rate distribution in a complicated ventilation network installed many regulators, an integrated system composed of expert system, exerting programs for simulation to get macroscopic characteristics and drawing diagram, monitoring system and so on is introduced in this study. This system is made up of airflow velocity sensors and computers linked to an local area network. The main results of this study are as follows; 1) Combinations of two branches to monitor aerodynamic resistance change in a branch p in a network can be selected by comparing factor's value in a branch relation table. 2) When the combination of sensor branches for a branch p does not exist in the network at present condition, the system changes aero- dynamic resistances of appropriate branch q placed a regulator by referring branch relation table. And then the system asks other computer to get macroscopic characteristics under altered value of aerodynamic resistance of the branch q. 3) Dot pattern diagram shows airflow rate relation between an active branch and a passive branch. Three relations such as a) a straight line, b) a monotonous curve and c) extremums are displayed in different patterns for all the sets between an active branch and a passive branch at a time. 4) The ranges of airflow rate in coal faces by changing aerodynamic resistance of any one branch placed a regulator are shown in the Pareto diagram using values in the branch relation table. 5) Ventilation transfer diagram with two parameter, one shows airflow rate in a coal face and the other shows energy provided by main fans to overcome aerodynamic resistance in a net- work, is utilized to decide countermeasures for decreasing energy consumption in the network on increasing of airflow rate in the specified branch.

Jan 1, 1995

By Peter G. Sechiari

The Rio Tinto-Zinc Corporation Limited (RTZ), through it exploration company Riofinex, commenced exploration for bauxite in the Amazonia region of Brazil during 1970. Following' encouraging indications, exploration licences were taken out and an exploration programme was initiated In February 1975, a preliminary 'feasibility report indicated that a project, based on the Miltonia plateau located close to the town of Paragominas in the State of Para, was viable and that barging might offer an economic solution to getting the product to an ocean-going port. A, decision was taken in April 1975 to proceed with a full feasibility study. In the latter stages of the study, an engineering consortium of Mendes Junior and Bechtel do Brasil was employed to review, and modify if necessary, the concepts that RTZ had developed for the project's operation. With these concepts agreed, the consortium was requested to make capital and operating cost estimates, and these became available during February 1978. The deposit is being developed by a Brazilian company Mineracao Vera Cruz S.A. (MVC) in which the present share-holding is owned 64 percent by RTZ and 36 percent by Companhia Vale do Rio Doce (CVRD). RTZ is a British based international group of mining and industrial companies with interests in almost every major metal and fuel. CVRD is a Brazilian mining company, 85 percent owned by the Brazilian Government, with a major interest in iron ore and also other non-ferrous metals. It is intended, in due course, that the company will become majority owned by Brazilian interests.

Jan 1, 1979

By Zeynep Aktuna

In this study, the formation of zeolites around Kizkapan and Karlikoy villages (Sothwest Kesan) were investigated. In this region, stratigrafically, Upper Eocene Kesan Formation, i.e. sandstone and rarely shale are observed at the bottom. Early Middle-Oligocene Yenimuhacir Formation is composed of sandstone, marl and tuffs. The zeolitisation is determined in the dasitic tuffs of the Yenimuhacir Formation. In this tuffs' zone, alteration had primarily resulted in zeolites, mainly mordenite, heulandite-clinoptiIolite. Silicification and alteration to clay minerals are also common. The Miocene-Pliocene Ergene Formation and alluvium deposits are the top units in the area. In the studied area, zeolite occurences have economic importance. The results show that successively rapid and short term periods are responsible for the clinoptilolite-heuylandite formations. The homogene chemistry of the solutions may be evaluated for a possible successive zeolitisation period. Multi-periodic vocanic activity and also circulation of thermal water had resulted in a continous dissolution of volcanic glass; moreover, resulted in the formation of suitable conditions of zeolite formation. The mineral crystallization sequences and alteration products as zeolites within the wall-rock, circulated solution reaction depends on a serie of parameters such as chemical composition of both initial materials and volcanic solutions during rock¬solution interaction period. The previous researches and the chemical studies support our results and observations in the studied area. The aim of this study is to investigate the presence of zeolitisation and to explain the formation steps of zeolitisation in Kesan Area by considering the content and distribution of major and minor elements determined in zeolite bearing tuffs. The chemical structures of both zeolite bearing volcanics and zeolite minerals are compared to the results of previous studies. Two dimentional behaviours of major and minor elements were discussed in order to caracterize zeolitisation development and to postulate a probable formation type of zeolitic alteration.

Jan 1, 2005

By D. Kruse, M. Sanaei

"3D finite element models of the Segmentally Lined Shaft (SLS) structure are simulated as means of numerical analyses of the system’s structural behavior. Top-down constructed rings, comprised of precast concrete segments, create a large diameter, relatively shallow underground space that can be utilized for various applications. To further investigate the effects of soil conditions and different loadings on the shaft structure, the FE model was run under various boundary conditions. Simulations include a) effects of various soil layers on the SLS, including a circumferential boundary of modified ground, b) effects of various soil layers on the SLS without any ground modification, c) Seismic analysis of the SLS with ground modification and d) Seismic analysis of the SLS without any ground modification. Comparing the analyses outcomes emphasizes the significance of the inclusion of the ground modification boundary in the structural performance of the SLS. INTRODUCTION TO SLS Underground structures are classically built rectangular in shape, which normally requires a two-step construction process beginning with installation of temporary shoring to support earth loads during the excavation, followed by the construction of the permanent structure. Attractive and practical alternatives are circular shafts referred to as segmentally lined shafts (SLS). The structure consists of a stacked series of rings formed from an assemblage of precast concrete segments. Top-down constructed systems of large diameter, relatively shallow SLS structures provide both temporary earth support during excavation and permanent structural support for many civil and building applications. The circular shafts sustain the lateral earth pressure mainly through hoop-stress mechanism, resulting in improved stability and structural efficiency. Cylindrical shell structures with large diameter to wall thickness ratios are prone to buckling under external pressure. In typical designs of small diameter shafts and tunnel linings with small diameter to wall thickness ratios, nonlinear buckling analysis (i.e., nonlinear geometric analysis) is usually not considered, since the buckling capacities for those structures are much higher than typical pressures encountered at their design depths. With an economically viable wall thickness, buckling becomes a critical issue, which should be addressed, for circular shafts with very large diameters. In the design and construction of the SLS, the stability of the structure can be improved by modifying the soil surrounding the circumference of the shaft to a limited thickness and to about 10 ft below the finished shaft structure. This thick wall of soil mixed with cement creates a composite integrated structure while serving additional purposes such as ground control and ground water seepage cutoff."

Jan 1, 2016

By E. A. Córdova

Current methods for scratching a piece of rock to obtain or check the characteristics of its component material can sometimes be expensive and time consuming. Scratching a rock core requires an object with a point that it is capable of sliding along the surface of the rock while recording the response from the rock due to the sliding. With the idea of providing a cost efficient solution for a scratch device, a new generation turntable arm, composed of a cartridge with a diamond stylus and a USB output connection to the computer, was used to record the vibrations from the sliding of the stylus along a rock core surface. The output sound from the stylus was captured with the computer as an audio input signal. The raw sound data was recorded in a standard waveform audio format (wav) file, and post-processed using sound spectrum analyzer software (Spectra-Lab) to capture numerical data such as frequency, amplitude, and noise from the file. The results for frequency, amplitude, and noise were compared and plotted against the scanned surface of the rock core in the search for correlations that might represent specific characteristics of the surface being scratched.

Jan 1, 2010

By T. J. Batchler

"INTRODUCTION A variety of standing supports are being applied in underground coal mining operations to assist in providing stable mine entries. Standing support performance requirements depend on the nature of the ground deformation behavior, and therefore require a good understanding of the interaction between the support and ground to achieve an optimum roof support system. Mining operations often employ standing support strategies that are unique to their mine. A support system that functions successfully in one situation could fail in another situation. It is important that the design and installation of the standing support systems provide the highest probability of preventing roof falls. Considerable research and development has been conducted by support manufacturers to develop standing support technologies for the mining industry. The National Institute for Occupational Safety and Health (NIOSH) researchers, with the cooperation of various support manufacturers, have developed a testing protocol that evaluates performance characteristics of these standing support systems.. Using this protocol, each of these support systems has gone through rigorous safety performance testing under controlled loading conditions in NIOSH’s Mine Roof Simulator (MRS). It is important to understand the unique performance characteristics of each type of standing support. This information allows mine operators to determine if the support system is compatible with the conditions in the mine and to compare each support system and determine if that support will provide equivalent or improved support capability. This paper provides a comprehensive summary of support performance to facilitate this objective. SUPPORT DESIGN CRITERIA AND THE GROUND REACTION CURVE Standing roof support systems are designed to prevent unplanned roof falls. The selection of the standing support is based on the interaction of the support with the surrounding rock mass, and its function is to assist the primary support system in maintaining the integrity of the immediate roof. The standing support works to control the immediate roof structure by resisting deformation that contribute to delamination of the bedded layers and displacements that lead to separation of the bolted zone from stable roof structures above the bolted horizon (Barczak, 2005). Standing supports should be installed early enough and develop sufficient capacity to bring deformation of the ground into equilibrium before a critical deformation is reached that leads to a detached block condition, at which point the standing support will be required to carry the entire dead weight of the detached rock mass to prevent a roof fall from occurring (Mucho, 1999). The ground reaction curve (GRC) can be used to assist in determining the compatibility and design requirements for a support system. It is important to understand the significance of the ground reaction relative to the support design requirements. The ultimate objective is to match the support behavior to the ground response and create equilibrium (stability) of the rock mass. This equilibrium is accomplished when the support loading intersects the ground reaction curve (Figure 1). Essentially, the ground reaction concept implies that the convergence in the mine entry is controlled by the magnitude of the support resistance. However, as a passive support, the standing support develops its loading through convergence. As such, the support needs to maintain its load capacity through the associated deformation of the ground and resulting entry convergence until the equilibrium condition is reached. This requirement causes factors such as the support stiffness, peak capacity, yielding characteristics, and stability to be fundamental to proper support design and application. NIOSH contributes to providing this understanding through full-scale performance testing of support products in the Mine Roof Simulator."

Jan 1, 2017

By Rajive Ganguli

A control algorithm was developed previously for loading coal trains such that each car met customer specifications (Ganguli, 2001). In developing the algorithm, the effect of the variance of coal was not investigated. This paper explores the effect of the variability of coal on the algorithm using two approaches: theoretical analysis and simulation. Both approaches demonstrate that variance is not an issue when the customer quality specification is close to the mine average quality. However, when they are far apart, the performance of the algorithm improves with variance.

Jan 1, 2002

By Z. T. Bieniawski

After many significant advances in mining, including development of sophisticated methods for strata characterization and numerical modeling analyses, the engineering design process in mining strata control is as primitive as it was two decades ago. Yet, major advances in design methodologies have occurred in other branches of engineering. Is creative design in mining a myth only? Are we deluding ourselves when we talk about innovative mining design of today? Did you know that most design experts are often unaware of their own decision-making processes? This paper explores the methodology of creative engineering design as a new recognized discipline.

Jan 1, 1987

By N. Standish

Leonard and Newman (1989) describe concepts and plans of their forthcoming project designed to increase the bulk density of broken coal at various stages of its production and handling. This is an excellent idea and something that will certainly be useful to the coal mining industry worldwide. The authors seek to achieve bulk density increase by "reducing oreliminating, through chemical additives and engineering design, particle voidage and enhance particle consolidation trickling between the point of breakage (at the face) and loading (in the shuttle car) to increase coal bulk density and productivity." In the paper, they present some supporting results of bulk density versus moisture, with or without oil addition, from the steel industry research. Unfortunately, the paper contains many misconceptions and half-truths that detract from an otherwise excellent objective of the project of increasing bulk density by reducing particle voidage -"the bottom line evaluator." Correct.

Jan 1, 1990