Search Documents

By J. L. Weeks

Discussion by J.L. Weeks Discussion I wish to comment on Kissell and Sacks's paper "Inaccuracy of area sampling for measuring the dust exposure of mining machine operators in coal mines." It is well established in industrial hygiene that area sampling is not an accurate measure of personal exposure. To measure personal exposure, one must use a personal sampler. Kissell and Sacks, using data from coal mining, reached the same conclusion. This is the right answer but it is the wrong question. This issue arises because the machine-mounted respirable dust continuous monitor (MMRDCM) is being considered to monitor coal-miners' exposure to respirable dust. This device may be mounted on a continuous mining machine, and it would take a modified area sample. I refer to it as "modified" because a mining machine is not really a fixed location, as is the typical area sample. The concern with whether this machine would provide an accurate estimate of the machine-operator's exposure, however, overlooks important features of the MMRDCM. Specifically, it displays dust concentration as it occurs and at the place where it is needed, not 10 days later, as is the case with the current system. Used in this way, it allows for timely intervention to control exposure to dust and it leads to greater first-hand knowledge of specific conditions and mining practices that result in excess exposure. If one knows the dust level is excessive at the time the dust is being generated, it is possible to use known and effective methods of dust control to reduce exposure. By measuring again, one can determine whether control methods have worked. This is a generic procedure followed in any industrial process: measure, adjust and measure again. It leads to more effective and more efficient dust control and is preferred to taking a sample, waiting 10 days for the results and then trying to apply that information to a situation that no longer exists. The MMRDCM also records the dust level automatically, and it runs continuously, making it harder to tamper with. Dust monitoring in underground coal mines has been corrupted by some operators having submitted fraudulent samples (and being convicted on criminal charges because of it), weakening the credibility of the current system. The MMRDCM is, in part, a response to this corruption, and an effort to focus attention on dust levels and dust controls rather than on the perpetrators of fraud. Use of the MMRDCM is an evolutionary change from the current system. With the current system, one takes a personal sample of exposure of the "designated occupation" (DO, defined at 30 CFR 70.2 (f)), the occupation regularly exposed to the highest level of dust on a section. Typically, on sections using continuous mining machines, this is the mining-machine operator. The rationale behind DO sampling rests on some of the findings that Kissell and Sacks report. They reviewed several studies that showed that dust concentration varies with location on a mining section and that there is a concentration gradient with the highest concentration occurring closest to the face. The logic behind DO sampling strategy is that if the dust concentration at the place where it is highest is below the exposure limit, then concentration elsewhere on the section is also below the limit. In this way, one will have achieved the objective or keeping dust concentration below the exposure limit for all miners on the section by measuring the exposure of only one miner. The

Jan 1, 2003

Surface contamination of minerals during fine grinding may occur due to coating of one material on the other. This can alter the surface chemical properties and adversely affect the separation of minerals by physico-chemical processes. In dolomite-silica system, selectivity was completely lost (compared to a synthetic mixture) after wet grinding of the minerals in spite of using a dispersant. Adsorption and surface characterization studies were conducted on silica particles separated after grinding with dolomite. SEM-EDAX analysis indicated the presence of dolomite on silica particles, which could cause the loss of selectivity.

Jan 1, 1993

By X. Shi, F. -Y. Wang

Automation and robotics are the keys to new intelligent autonomous mining systems that can remove operators from hazardous and stressful mining environments and provide the tools for greater productivity. This paper presents the components necessary for an Intelligent Task Control System (ITCS) for machine control in dynamic unstructured mining environments. In particular, the design details of a controller for an automated excavator are developed. The excavator controller uses fuzzy logic to interpret forces and torques gathered from a wrist mounted force/ torque sensor during the excavation process. This approach enables the transfer of human heuristics and expert knowledge to the controller. Several excavation tests using the fuzzy logic controller are described. These experimental results represent the first step toward an integrated approach that uses force/torque, vision and other sensor data to perform generic tasks in uncertain mining environments.

Jan 1, 1995

By M. Josick Comarmond, John J. Jeffery, John W. Bennett

Oxidation rates of sulfidic mine wastes measured at a range of size scales have been collected from a number of sources. The results suggest that well-designed laboratory columns, under controlled conditions, provide comparable information on oxidation rates to that obtained from field test piles. It has been found in the cases presented that laboratory measurements of oxidation rates of a particular material type can be applied with confidence to the same materials in the field. It is recommended that a further study be undertaken to measure the time-dependence of the oxidation rate for a range of particle sizes and different materials. This study would provide measurements against which models of oxidation rate as a function of time and particle size can be tested, to give confidence in the use of models to describe dump behaviour in the longer term.

Jan 1, 2000

By A. E. Jack Swanson, Brian P. Micke

INTRODUCTION Nevada Goldfields began underground mining development at the Kingston Project in September, 1986, followed by mill start-up in March, 1987. The first gold pour in April followed three years of preparatory work in establishing a North American operational base for the production of precious metals by Golconda Minerals N.L., an Australian mining firm. GENERAL CORPORATE BACKGROUND The Golconda Group of companies was established in early 1983 in Australia. It began operations by successfully retreating tailings at several old gold mining sites throughout Australia. With the limited reserves available for tailings retreatment, Golconda began to look toward the future by conducting a gold exploration program in Australia. However, the continued high price of gold in Australia had limited the possibilities of acquiring good properties at a reasonable cost and consideration was given to looking outside Australia in addition to Golconda's domestic exploration activities. North America was favored because of the proven potential for substantial gold deposits, the established infrastructure which would allow for rapid and cost-effective development of new projects and the advantages of similar political and economic climates. In mid-1984, Golconda established an office in California and began an extensive study of over 100 prospects throughout the United States. Two prospects were identified as a result of this study whch showed merit; one was located at Empire, Colorado and the other at Aurora, Nevada. Negotiations were then successfully undertaken to acquire these two properties. Golconda's U.S. offices were moved to Reno, Nevada in early 1985 to facilitate management of its projects. To operate and manage these projects, a small Canadian company listed on the Vancouver Stock Exchange, Cannon Minerals, was acquired by Golconda and renamed Nevada Goldfields Corporation. The current structure of the company is shown below in Figure 1. A private placement of 2,575,000 shares of common stock at US54.00 per share was arranged by Jacksons Limited of Australia in association with W.I. Carr (U.K.) Limited of London. This placement resulted in US510.3 million being available in May, 1986 for the acquisition and initial development of the Aurora and Empire projects. While the financing was underway, project planning commenced on both the Aurora and Empire projects. The Aurora project was selected as the one to be initially developed because of its relatively advanced stage of development. The

Jan 1, 1987

By R. D. Hamilton, W. J. Miles

In 1987, the International Agency for Research on Cancer designated crystalline silica as a 2A probable carcinogen. As a result, crystalline silica is regulated under the Hazard Communication Standard as a probable carcinogen at a concentration of 0.1% or greater in the workplace. Crystalline silica will be listed as "reasonably anticipated to be a carcinogen" by the National Toxicological Program. This designation of crystalline silica as a probable carcinogen has created major issues for the mineral and chemical producer, including labeling, hazard communications, marketing a material with potential hazard exposure, and potential liability. The State of California also regulates crystalline silica under Proposition 65 in products as a carcinogen, based upon the IARC determination that it is a probable carcinogen. More federal and state regulations are anticipated as a result of the IARC classification of crystalline silica and its subsequent federal regulation. Respirable crystalline silica has been regulated as a hazardous dust for many years by OSHA. This regulation was initiated to prevent silicosis, another occupational disease. OSHA has established monitoring devices for determining the concentration of airborne respirable silica in order to measure exposure to this substance. The accurate determination of the crystalline silica content is critical to dealing with these health risks and regulations. In the past, crystalline silica was considered to be safe and, because of its ubiquitous nature, little effort was made to determine or quantify its presence in most materials. The Hazard Communication Standard requires that a1l products containing 0.1% or greater crystalline silica must be properly labeled for this material and its hazard. Unfortunately, the 0.1% threshold was not chosen on the basis of established analytical capabilities for crystalline silica, but results from general limits for potentially carcinogenic chemicals and substances. Numerous methods have been developed for the determination of crystalline silica in a variety of products. However, these methods are not generally applicable since they must be specific for silica in any of its crystalline states and not just for total silica content. Chemical tests for silica are not difficult and quite accurate at the 0.1% level; however, in addition to its crystalline phases, it occurs in amorphous phases and in a wide variety of crystalline and amorphous silicates. In general, there is little correlation between total silica content and crystalline silica.

Jan 1, 1991

By C. N. Bensley, S. K. Nicol

The major developments in fine coal processing in Australia are reviewed. Emphasis is placed on the approaches taken by various Australian coal producers to improve the recovery of the coarse size fractions (minus 0.5 plus 0.25mm) and upgrade the selectivity of flotation at ultrafine sizes (minus 0.075mm). The effects on fine coal preparation of flotation circuit changes, the influence of physical and chemical variables on coarse coal flotation and the impact of spiral concentrators and column flotation, are discussed. Reference is also made to the development of oil agglomeration technology for the treatment of fine coal refuse and some of the factors which have led to its current demise.

Jan 1, 1988

By Ali Nazem, Rennie Kaunda, Zoheir Khademian, Fei Wang, Raymond Henn, Alex Peretiatkol

"The field demonstration portion of the Underground Grouting and Ground Improvement (UG&GI) short course offered by the Colorado School of Mines was held on May 18, 2016 at Baski Inc.’s Yard in Denver, CO.Numerous full field scale demonstrations of grouting methods and equipment were conducted under various field conditions. As part of these field tests, permeation grouting testing and demonstrations were also conducted. Various cement grout mixes were injected into 1.5-m (60-in.) tall transparent sand columns under controlled conditions (Fig. 1). The objective of the sand column permeation grouting demonstrations in the study was to show students the effects of ordinary Portland cement versus ultrafine cement on the engineering properties of the grout, and the permeation height through various types of soil stratigraphic layers in the sand columns. Similar previous demonstrations have had a specific focus on various brands of Type I-II Portland cements and ultrafine cements with a range of water cement ratios and injection pressures. More detailed information about these previous studies can be found in published proceedings (e.g. Henn et al., 2009 -2011).Equipment and material usedThe five clear plastic sand columns were 191 mm (7.5 in.) inside diameter and 1,524 mm (60 in.) tall. Each sand column had a 19 mm (0.75 in.) diameter hole drilled at the base (bottom) of the blind flange for injection of the grout. A perforated plate and/or screen at the base of the sand columns helped to prevent sand from plugging injection port. A ChemGrout grout plant was used for the demonstration consisting of 0.36 m3 (97 gal) high shear (colloidal) tank mixer, a 0.36 m3 (97 gal) agitator tank and a progressive helical cavity pump with maximum output capacity of 77 L/min (20 gpm) at a maximum discharge pressure of 265 psi (18 bar) (Fig. 2). A simple grout header arrangement consisting of control valves, pressure gauges, flow meter, grout delivery and return line, and a short injection line was also custom built. Also used were infra-red thermometers to measure the temperatures of the grout mix batches, CRD and marsh funnels to measure viscosity, baroid mud balance to measure specific gravity, and a digital scale to measure weights. The grout materials used were Holkim Portand cement (Type I-II), Nippon Steel Sumikin superfine cement and U.S. grout ultrafine cement."

Mar 1, 2017

By Charles J. Hass

INTRODUCTION Deformation measurements are some of the simplest and most useful measurements that can be made by the mining/rock mechanics engineer in assessing the sta¬bility of openings in rock. A number of tools and tech¬niques are presently available. This chapter will de¬scribe the most common instruments, their application, and present the equations needed for data reduction. MECHANICAL STRAIN GAGE Description of Instrument A mechanical strain gage of the Whittemore type shown in Fig. I is a useful instrument for measuring deformations of pillars, sidewalls, and roofs of under¬ground mines. Measurement gage lengths typically range from 51 to 254 mm (2 to 10 in.), and the dial indicator reads to 0.0025 mm (0.0001 in.). The instru¬ment measures the deformation between precision gage points which are anchored in the rock. The anchor points are typically grouted in small holes drilled 12.5 mm (1/2 in.) or so deep into the rock. Strain a is calculated from the measured deformation AL with the equation [ ] where L is gage length. A necessary accessory for the instrument is a master bar normally made from invar steel having a low co¬efficient of thermal expansion. This bar allows one to check the instrument for changes in the mechanical zero point and to correct for temperature effects on the measuring instrument. The instrument is available from Soiltest, Inc. for a cost of approximately $340; the cost of the master bar is approximately $55; and nonreusable brass inserts which are anchored in the rock are nominally priced at $0.27 each. All prices are for 1978. Applications Two classes of applications may be considered, one where only one measurement direction is involved and the second where three measurement directions are em¬ployed. Applications where only one measurement di¬rection is necessary include: monitoring crack or frac¬ture separation or shear movement with anchor points on opposite sides of the discontinuity; measurement of vertical strain in a pillar or sidewall; and measurement of steel support deformations with anchors in the steel members. The more general application involves a strain ro¬sette consisting of three measurement directions which for convenience are oriented 1.04 rad (60°) apart to form an equilateral triangle as shown in Fig. 2. Strains in the three measurement directions [ ]

Jan 1, 1982

By J. L. Young

The McLaughlin Mill started operating in January, 1985. For the first eighteen (18) months start-up, initial operation, and circuit debottlenecking have been done. The mill was designed to recover gold from a refractory ore requiring acid autoclaving pretreatment. This paper discusses the problem associated with bringing this complex hydro-metallurgical plant to consistently achieve design tonnages. Also, briefly described are the mill flowsheet, training program, permitting, and process and project development.

Jan 1, 1987

By David Green

Outokumpu introduced Flash Flotation in the early l 980's for the recovery of floatable material from grinding circuits. The devel­opment came as a result of surveys made in the company's own concentrators, initiated to find ways of improving recoveries with increasingly complex and lower grade feeds. Hydrocyclones make a separation on the basis of particle size and mass, resulting in the "over collection" of fine grained, high S.G. particles. Minerals such as pentlandite, galena and gold are easily caught in the circulating load around the mill until they are overground and rendered more difficult to collect. In the case of downstream flotation this may simply involve a reduction in the rate coefficient due to the finer sizes or, as is commonly experienced in gold operations, the mate­rial is slimed and coated onto non-floating gangue and is eventual­ly lost to tails. At the time of Outokumpu's plant surveys, it was a relatively common practice, particularly in Pb operations, to have a flotation section fed directly from the secondaiy mill discharge. This is called unit flotation and certainly provided an improvement but very high wear rates and frequent sanding out of the cells was com­mon. The development of the SkimAir® Flash Flotation cell by Outokumpu provided a subtle but quite dramatic departure from the unit cell approach. Now it was possible to feed cyclone under­flow into a special purpose-built flotation machine and recover a final grade concentrate from the grinding circuit (see Figure I). The cell was designed to handle the coarse circulating load, per­mitting the coarsest fractions to be short-circuited back to the mill and retain the floatable sizes for a nominal time of 30 seconds to several minutes. The short retention time was possible largely due to the relatively clean content of the cyclone underflow stream. This means that the fine gangue is not present except in small quan­tities and most of the fine to mid-size paiiicles are higher S.G. and more likely represent valuable mineral. This condition provides for very high rate coefficients. Typical operations would recover 40-60% of the valuable mineral in this fashion and improvements in recovery were typically from 2-5% for sulphide minerals to the 5-20% range for gold and silver.

Jan 1, 1998

By Michael Drozd

Introduction Flotation is a recovery process that utilizes natural or chemically-introduced hydrophobicity of minerals to separate ore from gangue by attaching the ore particles to bubbles. Flotation has been known since 1906, when it was patented by E. L. Sulman, H. G. K. Pickard and John Ballot. Flotation's first documented plant use was in 1911, when it was used on gravity tailings from a zinc plant. Cyanide leaching was first patented in 1887. Most early precious metals flotation was linked to lead or copper concentrates. Most precious metal flotation is linked to sulfide recovery and utilizes such reagents as xanthates, dithiophosphates and thiocarbanilides. But the involvement of flotation in precious metals recovery does not have to be limited to active flotation of the gold and silver bearing minerals. Flotation can be used to remove interfering minerals, such as carbon, or cyanicides, such as copper, arsenic bearing minerals or other cyanide complexing minerals. Cyanide Leaching The use of cyanide to recover precious metals is the backbone of the industry. The various recovery processes that use cyanide are: 1. Leaching-Counter Current Decantation(CCD) Merrill-Crowe 2. Carbon-in-pulp (CIP) 3. Carbon-in-leach (CIL) 4. Vat leaching 5. Heap leaching These processes are selected depending on ore grade, ore leaching characteristics, reserve size and capital limitations. Ore grade is used as the first criteria to determine the type of cyanide plant required. However, the reserve size can determine whether a ground ore alternative is used. The ore leaching characteristics may indicate that the higher recovery, associated with a process that employs grinding, is the only economic recovery alternative. There are some extremely large leaching plants with grades that would be non-economic for some existing heap leach plants. Many factors, such as strip ratios, metal recovery and reserve size, determine what the ultimate plant design will be. The exact processing scheme that is used, is a multifaceted decision matrix, which gives the process metallurgist some job security. Precious Metal Recovery Using Flotation Flotation recovery can conceivably be used on any ore that has been ground. Many operations utilize gravity separation on the ore to remove native gold from the ore prior to sending it to cyanide leaching. On certain ores, where the gold is in visible nuggets or particles, this processing alternative is advantageous because the native gold cyanide recovery is

Jan 1, 1993

By S. A. Hoenig

Introduction In an earlier publication, the application of exoelectron technology to the monitoring of dry grinding in a ball mill was reported. Recently, the author has investigated the ball mill problem in more detail with the system shown in Fig.1 . Here, some of the current generated in the ore-ball-water mixture was picked up by the metal chains and served as a measure of the rate of grinding. While the mechanism of current generation has not been completely clarified, a parallel study of electrical effects associated with rock drilling indicated that the major driving force is the zeta potential*, while oxidation of the freshly fractured material provides the remainder of the current. Both of these effects are sensitive to the exposed surface area, and it might be expected that the observed currents would provide a measure of the grinding rate. This "surface area" effect allows the measurement system to be used in any type of rock or ore grinding. Some studies with sulfide copper ore indicate higher currents than those observed with silica sand, but the overall pattern of current versus grinding rate is essentially the same. Experimental Studies The experimental system was set up as shown in Fig. 1. The initial studies were done with silica sand because of its availability and for comparison with the data of reference 1. The sand was sized to an average of 425 µm (40 mesh); a typical charge consisted of 2.5 kg (5.5 lb) of sand, 0.85 L (0.22 gal) of tap water and 2.5 kg (5.5 lb) of iron grinding balls 25.5 mm (1 in.) in diameter. For a typical "run," the mill was loaded with a fresh charge of ore and operated for periods ranging from 10-60 min. During this time, the current was measured with a Keithley 417 picoammeter and a chart recorder. At the end of the grinding period, the charge was removed and sieved to recover the 425, 300, and 212 pm (40, 50, and 70 mesh) fractions which were then drained and weighed. A fresh charge was used for each test and every attempt was made to keep the draining and weighing processes uniform. *The zeta potential is the voltage developed between the surface of a solid particle and the ion solution in which it is immersed. In the case of rock/ore materials in water, the zeta potential is negative.

Jan 1, 1984

By T. W. West

A description of a coal washing spiral is presented, together with a discussion of the parameters which define the envelope within which the spiral can be successfully applied. The correct process engineering, installation, operating and maintenance parameters are addressed as well as actual results for new and retrofit installations on USA coal capital and operating costs of spiral circuits are compared to those of traditional fine coal circuitry.

Jan 1, 1988

By Jorma Miettunen

The Plant. The annual production of the Pyhasalmi mine is 900 000 tons of copper- zinc-pyrite ore containing approximately 0.7 % Cu, 2.5 % Zn and 30 % S. During 1976...1981 altered surface ore, 850 000 tons in all, was also treated at the concentrator. The surface ore was crushed and ground in a separate plant and was then fed into the copper or zinc flotation or was flotated in its own circuit, depending on the degree of alteration and the content of copper and zinc in the ore. The surface ore was exhausted in October 1981. Flotation comprises three consecutive flotation circuits; copper, zinc and pyrite circuit. The zinc circuit includes an open circuit roughing and scavenging. The scavenger concentrate and cleaner tailing are pumped to the middlings flotation. Rougher concentrates of the open circuit and the middlings flotation are pumped to cleaning which includes four stages. Figure 1 describes the flowsheet of the zinc circuit.

Jan 1, 1982

By S. P. Singh

To understand the intricate nature of blast damage and counter the associated problems, small-scale blasting experiments were performed on hydrostone blocks. Tests were then conducted during a drifting operation in a quartzite quarry. Blast damage was assessed by different techniques. On the basis of the experimental results, the effects of the energy partitioning characteristics of explosives on the damage were identified.

Jan 1, 1993

By H. H. Murray

New and improved benefication techniques are available to allow the production of clay minerals of exceptionally high purity. This is particularly true for kaolins and smectites. Wet processing techniques including particle size separation, high intensity magnetic separation, chemical leaching, flotation, and selective flocculation are described and results and applications are discussed. The blending of clay minerals with other minerals provide opportunites to make special ceramic materials such as cordierite and other minerals which have very special ceramic properties including low heat expansion, high fired strength, low absorption, and other desired qualities.

Jan 1, 1989

By S. Meng, R. Jin, W. Hu

In alkaline pulp, galena is depressed by sodium carboxymethyl cellulose (NaCMC), while Cu(II) -activated sphalerite exhibits a high floatability so that satisfactory separation can be achieved. In addition to hydrogen bonding, chemical bonding of NaCMC with galena is confirmed by infrared (IR) spectra; only hydrogen bonding is involved between NaCMC and Cu(II)-activated sphalerite. It is also found that the greater the degree of substitution and polymerimtion of NaCMC, the stronger the depressive effect of NaCMC and that lower stirring speed favors the depression.

Jan 1, 1988

By M. T. Ityokumbul

Flotation is a surfaced-based separation process that exploits the differences in the hydrophobicities of the components. In the present paper, a review of both established and emerging nonmineral applications of flotation (oil removal, paper de-inking and separation of plastics) is presented and discussed. For each application, the theory of the process is compared and contrasted with mineral flotation. It is shown that the mass-transfer approach to flotation offers a good starting point for the analysis of these separation processes.

Jan 1, 1999

By Jing G. Yen

When a solid-liquid mixture is conveyed through a pipe,' four hydrodynamic conditions may develop depending upon the properties of the transporting medium, the properties of the transported material, the properties of the pipeline and the flow characteristics. They are classified as homogeneous flow, heterogeneous flow, intermediate flow and saltation. Heterogeneous flow, which is the subject of the present analysis, occurs when solid particles are coarse, of high density, and the mean velocity of the flow is relatively low, such that the combination allows the establishment of a pronounced concentration gradient in the cross-section of the pipe. In this type of system the suspended matter does not change the rheological properties of the conveying fluid, and solid and fluid phases behave somewhat separately. In recent years much work has been directed toward gaining more insight into the hydrodynamics of heterogeneous flow (1,2,3,4,5,) However, almost all knowledge obtained is empirical in nature and limited in scope. Much effort has been extended to collect experimental information on the energy losses associated with systems of slurry flow (6-13) The work of Durand and Condolios(14,15) represents one of the most extensive experimentations in this field. Through systematic test runs, the effects of the major flow-parameters were studied one at a time. From the results, they concluded empirically that:

Jan 1, 1969