Search Documents

By J. Chai, Q. Yuan, B. Qiu

"Overburden strata deformation monitoring is one of the key problems in ground control. Using geophysical method through surface drilling to detect strata deformation is commonly used in the industry. In this paper, a geophysical method based on the distributed optical fiber sensing (DOFS) system were conducted in the laboratory, where a DOFS-based strata deformation monitoring experiment was performed with three physical models. The results show that the DOFS method precisely detects the rock mass deformation and strata structure forming with the Brillouin frequency shifts (BFS) representation. The BFS curves are divided into three phases, which reflects the horizontal three zones developed in the overburden. The BFS distribution presents a multiple stages form, the 1st stage corresponds to the caving zone and the 2nd stage corresponds to the fracture zone. Based on the multiple stages form, the evolution of the water flowing through fractured zone have been determined and the controlling effect of key strata over the water flowing fracture has been pointed out. In the end, the comparison validation proves the accuracy and reliability of this method, and it could be a new approach for the ground control research. INTRODUCTION Overburden rock strata above the work face space will propagate from slight deformation, part destruction to violent movement because of the underground coal mining. It is fundamental and an intrinsic requirement of ground control to monitor the mining-induced rock mass deformation.[1] Overburden strata have their significant mechanical behaviors and movement under damage deformation and fracture. Overburden strata deformation affect the mining ground pressure control directly, and performance in the relationship of supporting equipment and the surrounding rock, the mining-induced fracture distribution and the loss of underground water resource, the ground surface structure stability and the ecological environment.[2] From the perspective of the concept of safe and efficient scientific coal mining: the overburden strata deformation is an important part of mining method selection and reasonable supporting solutions decision which can solve the issues like the roof supporting force calculation, overburden fracture distribution and gas drainage, ground subsidence, separation of coal and rock control and top-coal recovery rate and so on. From the perspective of green and ecological mining: the overburden strata deformation is the key basis of studying the mining-induced ground subsidence and mining area ecological damage, and such engineering problem like environmental protection in mining area, ecological restoration in mining subsided land and the water conservation in fragile ecology area of mining could be solved based on it.[3-6] Therefore, the mining-induced overburden strata deformation is the key of ground control and needs to be controlled artificially."

Jan 1, 2017

By Bernard L. Cohen

INTRODUCTION The most serious occupational radiation episode in U.S. history was the exposure of uranium miners to radon daughters in the 1945-1968 time period. Although the maximum permissible dose at that time was 12 WLM (working level months) per year, average exposures were several times that figure, and ten times higher exposures were not uncommon. Starting in the early 1960s, mounting epidemiological evidence appeared for an excess incidence of lung cancer among these miners; up to 1974, there was an excess of 134 cases (159 observed vs 25 expected) among the 4000 in the group under study (NAS-1980). When this excess became apparent, the Federal Government took jurisdiction, greatly tightened enforcement, and in 1969 lowered the maximum permissible exposure to 4 WLM per year. These standards were met largely by a great improvement in ventilation. As a result of these measures, average miner exposures were reduced 5-fold from 1965 to 1968 and by another factor of 3 by 1970. In 1978, the 4 WLM/year maximum permissible exposure was exceeded by only 37 of 7500 underground miners, for only 16 wars it exceeded by more than 25%, and for only 8 was it exceeded by 502 (AIF-1980). The average exposures to the various groups are listed in Table 1. We see that the average exposure for all miners was 1.03 WLM, and for those who worked essentially full time underground it was 1.45 WLM. For purpose of later discussion, it will be convenient to choose a single value for average exposures. In view of the fact that employment situations and job categories are bound to vary over a lifetime of work, we take this to be 1.3 WLM/year. The purpose of this paper is not to dwell on history, but rather to address the question of whether or not this present situation is satisfactory. This question was considered recently by a study group under the auspices of National Institue of Occupational Safety and Health (NIOSH-1980) and it answered the question in the negative, concluding that the maximum permissible exposure should be substantially reduced. However, their arguments were incomplete and were lacking in perspective. The principal thrust of this paper is to provide some of the material overlooked. RISK TO URANIUM MINERS FROM RADON EXPOSURE In order to quantify the risk to uranium miners under present working conditions, it is first necessary to estimate the risk of lung cancer per WLM of exposure. The most straightforward way of doing this is to use the data on the group of uranium miners under study. These are listed in Table 2 for 8 exposure ranges and for the total group (NAS-1980). If all data are given equal weight, the risk is seen to be 3.5 x 10-6 per year per WLM. Much can be said in favor of using this value for the risk as dose independent; it is within one standard deviation (SD) of the observations in 5 of the 8 dose categories (as expected from the definition of SD), and within 2 SD for all 8, and for the three cases differing from the mean by more than one SD, two are above and one is below. However, the uranium miner exposures in the present situation will be far below those covered in Table 2, so it is worth considering the possibility that the risk differs from this at low doses. From the last column of Table 2 we see that the experience from all exposures below 600 WLM indicates a risk higher than the mean for the entire group by more than two standard deviations (the value 600 WLM in this comparison was deliberately chosen to maximize this deviation; for exposures below 360 WLM and 840 WLM, the excess is only 1.0 and 1.6 standard deviations respectively). In view of this tendency for the risk to be higher at lower dose, we will take the risk to be 5.0 x 10-6 per year per WLM in what we will refer to as model A. This risk estimate is based entirely on exposures much [higher] than those that will be experienced by

Jan 1, 1981

By R. Xiong, A. K. Fallaw, G. Wang, L. R. Moore, S. Dobson, J. Gu

"INTRODUCTION The Central District of the Florida phosphate industry is located in southwest Polk and southeast Hillsborough Counties, with the Southern Extension lying in western Hardee, eastern Manatee and northwest De Soto Counties. (Lawver, 1983) Figure 1 shows the major phosphate formations in Florida. Almost all Florida phosphate production has been in the Central district with additional production from a mine in the Northern District. The Central District is comprised of the Bone Valley Deposit, a relatively thin layer of high grade ore which has been the main source of phosphate mining for decades, and the Hawthorn formation, a thick but low grade formation which covers most of peninsular Florida. (Lawver, 1983) Florida phosphate producers use the Crago process where calcium phosphate is floated with anionic, fatty acid type collectors followed by cationic reverse flotation of silica with amine type collectors. The phosphate matrix is put through various size separation techniques to obtain a typical -28 Mesh (< 700 µm) particle size for fine flotation and a -16 mesh (< 1190 µm) to +28 mesh (> 700 µm) particle size for coarse flotation. In some cases this coarse fraction can be sent to shipping as an intermediate product. The +16 mesh (>1190 µm) to – ¾“ (19 mm) fraction is sent to shipping as a final product called pebble. Figure 2 demonstrates a simplified diagram of the mining and processing of calcium phosphate (matrix) through a Central Florida mine. Particle size and mineralogy are important considerations in the Crago process for two main reasons, the mass of the particle and the particle surface area. Both of which are dependent on the coordination of the anionic collector to available Ca2+ sites on the minerals’ surface. The increased surface area, and available Ca2+, of the smaller apatite particles will allow for more fatty acid molecules to coordinate than the larger particles, with a lower availability of Ca2+. So, the larger particle would require more collector to be introduced in the system to sufficiently cover the apatite particles to produce a surface sufficiently hydrophobic to attach to air bubbles allowing flotation to occur. (Guan, 2009) The Bone Valley deposit has very favorable flotation characteristics when compared to other mining ores around the world. The matrix of the Bone Valley is relatively high grade, BPL (Bone Phosphate in Lime) values typically range from 6-18%, BPL recoveries, from such a matrix, can often be achieved above 85+% with fatty acid based collectors dosed below 1 #/ton. As mentioned, the sizing is an important step as there is also high grade apatite in the +16 mesh (1mm) that is screened to a final product grade, 60-65% BPL. The lack of quartz in the larger size fraction has allowed the Central District to produce high quality, low cost phosphate product, called pebble, through effective screening with no further beneficiation. (Guan, 2009)"

Jan 1, 2015

By Don Suttie, Frank Roybal, John Wright

The Roybal Raise incorporates the simplicity and low cost of a short bald-headed raise while overcoming the usual impediments to driving a high baldheaded raise. The concept provides for speedy excavation and maximizing the use of the excavated opening, using the rock for structural support. The design is simple: two baldheaded raises are driven parallel to one another, interconnected by dogholes about 8 m (25 ft) apart. In this fashion, the raise can be driven safely and efficiently to 60 m (200 ft) or more. When the raise is complete, the excavation requires no timber for support or partitioning. Rather, the rock itself supports the construction. As a test, a two-compartment Roybal Raise was attempted at the Independence mine in the Willow Creek District of Alaska. One side was driven 2 x 2 m (6 x 6 ft), intended for a manway and equipment skip. The other was driven 1.5 x 1.5 m (5 x 5 ft) for a muck compartment. Both sides were driven at a 65° angle from horizontal and 1 x 1 m (4 x 4 ft) dogholes spanned the 4.6-m (15-ft) pillar between the two compartments. After topping out at 50 m (160 ft), the raise was found to meet all expectations of efficiency, low cost, and practical simplicity. Technique Preparing the Roybal Raise for driving involves no elaborate or costly site prep except assembling materials and providing for muck removal. Normally, the raise muck falls directly onto the sill or track and is picked up either by an overshot mucker or a front-end loader. Raise mining proceeds initially by taking up both compartments simultaneously to the first doghole. It progresses by alternating one side as a clear manway for access with the other side, the active side, as a muck compartment (Fig. 1A). This stage proceeds quickly for no mucking or staging is required to cycle the first three rounds. On the fifth round, in addition to the normal raise round, rib holes are winged out toward the adjacent raise, thus starting the dogholes. Finally, as the sixth raise rounds are drilled and shot, the first doghole is also completed from both sides. The second stage commences by establishing one side as a clear manway for access while the other side, used as a muck compartment, is prepared for active mining. Figure 1B illustrates this step in the succession of raising with the active side advancing to the second doghole level. During this stage, services are maintained through the manway side and equipment is stowed in the doghole during blasting. As the active side advances, muck may be allowed to fill the bottom portion of that side since it is unnecessary to clear it for access. The next stage of raising involves cleaning out the former muck compartment and preparing it for use as a manway. At the same time, the former manway is prepared for advance and use as a muck compartment (Fig. 1C). As in the previous step, the same doghole is used for access and equipment storage. The active side advances until the second doghole is completed, at which point equipment and access are moved to the new doghole. From there, the active side is driven past the second doghole 8 m (25 ft) more to the third doghole level. Again, half of the doghole and the next raise round are mined. The fourth stage involves switch ing back the manway side for the muck side (Fig. ID). The new muck side is driven to the third doghole where equipment storage and access are reestablished. From there, the active side is advanced to the fourth doghole. In the same fashion, the raise is advanced to the top, alternating the manway side with the active side, maintaining access through the inactive manway, and storing equipment in the uppermost doghole. The cycle time for driving each compartment, regardless of the raise height, is greatly improved over that for normal bald-headed raises of comparable height. By storing equipment in the upper-

Jan 1, 1984

By Bob Snashall

"We could blow that damned fort out of existence if we could run a mine shaft under it!," claimed one Union soldier eyeing Bobby Lee&apos;s Petersburg defense line protecting Richmond and Jeff Davis. Puncture the line, take the hill behind, and the Confederate capital would celebrate Yankee jubilee, 1864. That was June. At 4:15 am, July 30, mine boss Henry Reese, sergeant, 48th Regiment, Pennsylvania Volunteers, gingerly entered the mine, dark and muddy. Something had gone wrong. The mine, set to go off at 3:30, hadn&apos;t exploded. It had to be checked. The main mine gallery, 1.5 m high x 1.4 m wide (5 x 4 ft) narrowing at the top to 0.6 m (2 ft), forced Reese into a tuck run. Some¬where up there in that 155 m (511 ft) stretch running 6 m (20 ft) under the rebel works, moisture may have doused the charge. Or maybe a fuse splice went awry. Or maybe there was live fire steaming like a locomo¬tive towards 3.6 t (4 st) of black powder. Perhaps now Reese wished this sprint was shorter. For the mine boasted a record break¬ing distance in military annals. Lieut. Col. Henry Pleasants Credit goes to Lieut. Col. Henry Pleas¬ants, commander of the 48th, who overheard the soldier&apos;s claim for what a mine could do. In peacetime, Pleasants had been a railroad engineer working on the Sand Patch Tunnel. He later switched to mining, working for the Philadelphia & Reading Coal & Iron Co. He even married the daughter of the editor of The Miners Journal. Grieving over his wife&apos;s early death, Pleasants plunged into the ven¬ture of war. This Union officer took the mine idea to the brass. Headquarters was less than enthu¬siastic. "The chief engineer of the Army and the rest of the regular Army wiseacres said it was not feasible," Pleasants wrote to his uncle. The pros scoffed, ticking off a list of horribles: No mine has ever gone that far, men will suffocate and be crushed, the rebs will countermine, the men will be trapped. Still, Pleasants eked out a signal to proceed. In the meantime, the miners of the 48th had commenced to dig anyway. It was like the 48th to proceed against the odds. The 48th Pennsylvania Volunteers The 48th had been recruited from Penn¬sylvania&apos;s Schuylkill County, anthracite coal mining country. The mines had been torn with strife over wages. Strikes and rioting were prevalent. Murder was not unknown. This "Buckshot" resistance centered in Pottsville, PA. It forced the governor to call in troops. Coal was in high demand to run the war machine. Pennsylvania operators worried that a military draft would stir up violence, closing the mines altogether and further shift¬ing business to emerging Illinois mines. Men lit out for the western gold fields in the tens of thousands. Secret societies bred in the mining camps invited draft agents to dance at the end of a rope. Jobs threatened by cheap, victorious South¬ern labor were one warning intended to get immigrant miners interested in the war. Operators gave miners time off to help de¬fend Philadelphia during Lee&apos;s thrust to Gettysburg. Even so, the draft spawned new violence and troop intercession. Soldiers were not welcome. The dust had barely settled when into this Pennsylvania "minefield" marched the 48th on a recruitment drive. The 48th had been in Lexington, KY on guard duty. When it came time for the regiment to pull out, the townspeople had prevailed upon authorities to extend the regiment&apos;s stay. Finally ordered to move out, the 48th was feted by a hanky-waving, tear-dropping send-off to the lyrical lament Auld Lang Syne. And Kentucky fancied itself to be rebel. Striding smartly into the Pennsylvania coalfields, the 48th attracted 400 recruits and marched off under regimental colors specially made by the proud citizens of none other than Pottsville, PA.

Jan 1, 1989

By Luis Tavares Ribeiro

Dynamic programming is based on the-, application of a simple property formulated by Bellman in his principle of optimality (Bellman, 1957): "An optimal policy has the property that whatever the initial state and initial decision are, the-remaining decisions must constitute an optimal policy with regard to the state resulting from the first decision". The method is charaterised by: (Dowd, 1979) a) A function defining the total value at each decision time of the system. b) The set of permissible decisions. c) The present state of the system. d) The number of steps remaining before the procedure is terminated.

Jan 1, 1982

By T. W. Camm

In this US Bureau of Mines report, mine and mill cost models are presented to make estimates of the cost to develop mineral deposits in the desert region of the southwest United States. Regression analysis was used to generate capital and operating cost equations for each model based on daily production capacity. These models are used for Potential Supply Analysis (PSA) studies by the Bureau, which analyzes the economic benefits of minerals in a region.

Jan 1, 1995

By JIAQI JIN, Joe Milbourne, Maoming Fan

Gold is very important to support the financial system, and to be used in industries of the jewelry, high-tech fields such as electronics and aerospace, etc. Gold is mainly extracted from three types of ores: primary ore (vein gold), placer (alluvial gold) and associated ore. Cyanide was widely used in gold ore flotation to depress gangue minerals and leaching/cyanidation. The process of extracting gold from gold ore, its separation and flotation concentrate, specifically through a technique called cyanidation or cyanide leaching. This method, which has been dominant since the 1970s, utilizes a dilute solution of cyanide to dissolve gold from the ore. While effective, the use of cyanide raises environmental and safety concerns due to its high toxicity. Cyanide spills can have severe environmental consequences. This has led to the exploration of alternative, environmentally friendly reagents. This paper discusses processing results using the alternative flotation depressants such as sodium sulfite (Na2SO3), etc. to produce a goldrich flotation concentrate for sale to a smelter or as feed to an alternative leaching agent. and methods to extract gold from ore without relying on cyanide.

Feb 22, 2026

By M. D. McInnis

The Jualin Gold Prospect is centered on Johnson Creek, approximately 40 air miles north-west of Juneau, Alaska. The property is on the southern end of the Kakuhan Range with Berners Bay immediately to the south and Lynn Canal to the west. The property is accessible directly by helicopter from Juneau or by float plane to the head of a 5.5 mile gravel road that begins on the north side of Berners Bay and terminates at the old workings of the Jualin Mine near the center of the property.

Jan 1, 1989

By David D. Gallagher

Customer demand for greater efficiency and reduced operational costs on modern overland conveyors has focused attention on the conveyor belt&apos;s rolling resistance properties. Studies have indicated as much as 60% of the power losses on a long horizontal conveyor can be attributed to the indentation of the pulley cover rubber as it passes over idlers. This paper will compare tan delta values of different compounds with large scale rolling resistance test data from the University of Hannover. Results will then be compared to actual power consumption data gathered on several long overland conveyors using identical belt construction except with different pulley cover compounds. Concluding comments will be made indicating substantial operating cost differences based on the rolling resistance of the cover compound.

Jan 1, 2000

By C. W. Newcom

The mining industry continues to be under expanded scrutiny in the health and safety arena, both from federal regulators and the media. While this paper will briefly discuss how enforcement activity, both with citations issued and the size of penalties proposed, the primary focus will be practical suggestions to deal with some key, high-risk areas for a mine operator which could have substantial impact, both in terms of liability and mine operations. It goes without saying that all mine operators need to continue compliance programs they have in place with careful ongoing evaluation of those plans for areas of improvement. The focus here will not be compliance as such, but rather steps to take and procedures to have in place to try to minimize risks in the face of the potential for more significant liability. Thus, our focus will be procedures to respond to unwarrantable failure citations, immediately reportable accidents, and to deal with potential pattern of violation issues.1

Jan 1, 2011

By J. O. Marsden

This paper presents an overview of the innovative methods for gold and silver extraction that have been put into actual practice in North America since 1987. It is an update of a paper of the same title which was presented by Sass and Mansanti at the AMC conference in San Francisco in 1987. New practices, new equipment and variations of older practices that have been introduced in the last five years are discussed in each of the following categories: process selection trends, comminution, gravity concentration, flotation, oxidation, agitated and vat leaching, heap leaching, solution concentration and purification, zinc precipitation, electrowinning, tailings disposal detoxification, and reclamation.

Jan 1, 1993

By Harold E. Goetzman, Blair R. Benner

The U.S. iron ore industry is located primarily in Northern Minnesota and Michigan&apos;s Upper Peninsula with one additional small plant in Missouri. There are currently some 10 plants operating that produce about 48 million tons per year of pellets. The major reagent use occurs in the three general areas of: flocculation, flotation and pellet additives. Minor areas of usage are for corrosion inhibition and dust suppression. Current practice as to types of reagents, consumption, and method of application are reviewed. The interaction of reagents with other parts of the process are discussed. Also included is a discussion of future reagent needs.

Jan 1, 1994

By Leonard Harris

Mining is a business and, therefore, is expected to make profit for its investors, like any other business. It is a risky business which requires the expertise of professionals from several disciplines to make it successful in the finding, evaluation and development of a new mining venture. Many of the same disciplines, as well as experts in some other fields are required to operate the facilities once they are built. To manage all this, wide-ranging, versatile and sharp managerial skills are required. On the U.S. domestic front, the most important management issues requiring attention today and tomorrow are the increasing unwarranted attacks by anti-mining groups and legislators on the industry and aided by an unchallenged, but widespread, public view that mining is not necessary and damages the environment. Higher costs to mine and process deeper and more refractory ores are also of great concern. More and more attention is being focused, therefore, on overseas projects under the belief that undeveloped countries will recognize the economic value of mineral production and that lower costs can be achieved.

Jan 1, 1993

By N. T. Mirafuente

The device called "Dynastat" which is described in this paper provides in situ borehole measurements of dynamic and static parameters for use in a wide range of design applications. In the dynamic mode, the Oynastat allows measurement of shear and compressional wave velocities. From these velocities in situ dynamic Young&apos;s modulus and other dynamic elastic parameters can be calculated. In the static mode, the device allows measurement of load versus deformation from which in situ static Young&apos;s modulus can be determined. Information on in situ horizontal stress fields can also be estimated from the load deformation curves. In both mining and civil engineering applications, in situ measurements of material properties are indispensable for accurate evaluation of design problems. Laboratory dynamic and static test measurements in comparison to in situ measurements are often misleading due to difficulties in obtaining undisturbed samples and in accounting for effects of discontinuities, etc., for mass properties. The authors contend that among in situ borehole measurements, the method employed with the Dynastat is the most accurate and detailed technique of measurement. The Dynastat employs the crosshole method of shear and compressional wave velocity measurements and also performs as a borehole jack to obtain load-deformation relationships of materials at exactly the same location at depth in boreholes.

Jan 1, 1976

By Milan Yekich, Emanuele Cauda, Justin Patts, Cody Wolfe

A worker’s personal exposure to respirable dust in occupational environments has traditionally been monitored using established methodologies which entail the collection of an 8-hour representative sample that is sent away for laboratory analysis. While these methods are very accurate, they only provide information on the average exposure during a specific time period, generally a worker’s shift. The availability of relatively inexpensive aerosol sensors can allow researchers and practitioners to generate real-time data with unprecedented spatial and temporal granularity. Low-cost dust monitors (LCDM) were developed and marketed for air pollution monitoring and are mostly being used to help communities understand their local and even hyper-local air quality. Most of these integrated sensing packages cost less than $300 per unit, in contrast to wearable or area dust monitors specifically built for mining applications which have been around for decades but still average around $5,000 each. At the National Institute for Occupational Safety and Health (NIOSH), we are leveraging the power of high-volume data collection from networks of LCDM to establish baseline respirable hazard levels and to monitor for changes on a seasonal basis as well as following any application of control technologies. We have seen the effective use and advantages of monitoring live data before, during, and after events like shift changes, operational changes, ventilation upgrades, adverse weather events, and machine maintenance. However, many factors have prevented a systematic adoption of LCDMs for exposure monitoring: concern for their analytical performance, the complexity of use, and lack of understanding of their value are some factors. This contribution outlines a one-year case study at a mine in Wisconsin USA, covering the installation, maintenance, data visualizations, and collaboration between NIOSH researchers and the industrial hygiene professionals at the mine.

Feb 1, 2024

By I. Iwasaki, T. Fujuita

The removal of phosphorus from steelmaking slags is essential for recycling such slags to blast furnaces for recovery of their manganese, iron, and lime contents. Phosphorus is mainly concentrated in the dicalcium silicate phase of the slags (Fujita and Iwasaki, 1988, 1989; Suito, et al., 1977). Slow-cooling of steelmaking slags in an air atmosphere increased the grain sizes of constituent minerals; however satisfactory magnetic separation results could not be attained because of the close association of a strongly magnetic ferrite phase with dicalcium silicate (Fujita and Iwasaki, 1988). Curie point of the strongly magnetic ferrite phase in the slow- cooled steelmaking slags was investigated and an attempt was made to separate the phosphorus-bearing dicalcium silicate phase in ground slag pulps heated to a temperature exceeding the Curie point. Materials and methods Slag samples, heated to its fusion temperature of 1370°C and slow-cooled in an air atmosphere, were ground dry to -90 µm (about 170mesh) in a ring grinder. The ground sample was pulped to 1% solids in distilled water using 1 kg/t sodium hexametaphosphate as a dispersant and separated in a Sala high gradient magnetic separator, Laboratory Model 10-15- 20B, using a 100-mesh expanded metal matrix and 300 m/h flow rate.

Jan 1, 1990

By Ralph W. Barbaro

In the mineral industry, the objective of a mining venture is to extract, process, and market a mineral commodity in such a manner that the profit of the venture is maximized. In a mining venture, a company normally has control over mine production scheduling, the selection and location of processing facilities (mineral beneficiation plants, smelting plants, refineries, or blending facilities), processed ore blending, and the selection of markets. The flexibility of the above factors provides many alternatives to satisfy the needs of each market with regard to quantity and quality of ore. The purpose of this paper is to present a mathematical model for determining the alternative that yields the maximum profit. Production planning is generally concerned with the best utilization of fixed resources, more specifically, with the determination of production and inventory levels to meet fluctuating demand requirements. A mine can be any source of ore such as an entire mine, a production unit within a mine, or an independent supplier. The objective of production scheduling is to determine the times at which each mine will be used and to allocate a required level of production. Production planning and scheduling problems are intimately associated with the location of new and existing mines and processing facilities. Although the location of the mines is usually fixed, there can be considerable flexibility in locating new processing facilities, in the selection of the processing plant, and in blending the ore before and after processing.

Jan 1, 1983

By K. Terhaar, K. Prisbrey

The objective was to determine operating protocols for a lead and silver column flotation cleaner being considered for installation at Sunshine Precious Metals Inc. &apos;s Kellogg mill in Northern Idaho. In this column, tetrahedrite and galena were floated, and pyrite and other gangue minerals, including siderite and silica, were depressed. The procedure was to develop a dynamic simulation using a linear transfer function approach. The transfer function related cause-and-effect variables such as the influence of collector and depressant dosages on recovery and grades. Bench-scale flotation tests followed by pilot column testing provided the data used to develop a linear transfer function. The transfer function was derived using a spreadsheet. This model was applied to simulate how the flotation column could be made to respond to disturbances in feed grade. The results were that xanthate, zinc sulfate and sodium cyanide were found to be suitable controls for grade and recovery. Simulations showed the best sequence of manipulations of these reagents, and these sequences are useful for future operator training. The conclusion was that linear transfer functions were able to simulate lead and silver recovery, develop scenarios for operator training and provide a foundation for future on-line control.

Jan 1, 2002

By J. E. Hoffman, Massimo Maccagni, T. J. Keefe, Marco Olper, O&apos

The problem relating to the use of insoluble anodes in acidic and highly aggressive environments has still not been definitely solved, and it is therefore a recurring subject of discussion. The fields of application in which insoluble anodes play a fundamental role are mainly in the electrolytic extraction of metals, in cathodic protection with impressed current, and in the production of oxidized halogenated salts. Based on the foregoing, B.U.S Engitec Servizi Ambientali (BESA) developed an electrode suitable for the use in the above-mentioned system. The basic component of the BESA anode is a bimetallic wire made of a copper rod (core) covered by a thin layer of valve metal, to be chosen between tantalum (Ta) and niobium (Nb). The wires, coated with suitable catalyst (PbO2, Pt or others) are inserted in a plastic frame and fixed to a current feeder by means of a screw, ensuring an optimal contact. Experimental data on the operating conditions, such as kind of electrolyte, current density, electrode potential, corrosion tests and fields of possible application, are described.

Jan 1, 1993