Search Documents

By R. C. Berry

The Environmental Impact Statement (EIS) has become a routine requirement for mining operations on federal lands. A similar document is being required in developing countries. Baseline studies are needed prior to writing an EIS and these studies involve surface water, groundwater, air quality, and wildlife/ native plant evaluations. The required baseline hydrology and geochemical studies are often the most expensive and lengthy evaluations. This paper summarizes the hydrology and geochemical baseline studies required for .An EIS and presents suggested methods to expedite these studies and to shorten the time and the cost to complete the studies and the EIS.

Jan 1, 1999

By A. Tarigan

The integration of the ESZ orebody and DOZ orebody resulted in a much larger footprint than the original DOZ Mine shape. The significant change in footprint geometry presented new cave front management challenges, specifically: longer undercut drifts. Using a constant blasting rate, more time is required to complete caving in each drift which ultimately influences the number of active faces at any point in time. The number of manageable active drifts is controlled by the planned square-meters of undercut blasting, lead/lag restrictions and other specific conditions such as the need to blast pre-charged explosives. In early 2008, an evaluation of the existing plan showed that significantly more active undercut drifts and longer cave fronts would occur in the next five years. Difficulties associated with the long cave fronts led to a decision to redesign the caving sequence. Several different boundary options based on operational, geotechnical and ore grade parameters were investigated. This paper describes the issues faced with long cave fronts, the constraints and requirements to effectively manage the caving sequence and the options considered to mitigate this situation.

Jan 1, 2010

By Kai Koosmen, Mehdi Serati, Tengzhou Wang

Spalling and rockburst are unwanted brittle failures at the boundaries of underground excavations that are commonly observed in hard rock and high-stress environments at significant depths, although, spalling has also been observed in comparatively shallow soft rocks. The crack initiation (CI) stress threshold (representing the stress level at which new micro cracks begin to form in an intact rock) is widely used to establish the in-situ spalling strength, and is generally regarded as the lower limit of the long-term rock strength. This study analyses the evolution of CI and other mechanical properties for a high-porosity sandstone with an average UCS of 38 MPa under unconfined cyclic compressive loading. The results indicate that rock properties are variably affected by cyclic loading with; no significant effect on Youngs Modulus; a moderate increase in Poisson’s ratio and fracture angle; a moderate decrease in UCS; and a major reduction in the CI stress threshold. All of these changes were generally amplified by cyclic loading at higher stresses. From the results, it is concluded that rockburst and spalling limit in underground structures may reduce over time if the rock is subject to repetitive cyclic loading, and that the reductions will be greater for higher cyclic stresses. This may be a significant factor in the design and operation of some deep underground structures.

Apr 26, 2022

By Samuel S. Adams

Economic concentrations of potassium are essentially limited to thick, stratigraphic sections of marine evaporites. These deposits were precipitated through the evaporation of sea water in restricted epicontinental seas or in grabens related to continental margin rift systems. Following deposition the deposits were subjected to diagenesis and varying degrees of metasomatism and structural deformation. The origin and characteristics of potash deposits are easier to study and interpret than those of most ore deposits because the phase chemistry of the salt systems is known and the approximate composition of the ore-forming fluid (sea water) can be inferred with confidence. It is particularly helpful that the temperature and pressure of deposition approximated that of present earth surface conditions and the pertinent mineral assemblages can readily be duplicated in the laboratory. The study of these comparatively simple salt deposits provides examples of the practical advantages of understanding the genesis of an ore deposit. These observations, in turn, illustrate the importance of pursuing research on the more complicated magmatic, hydrothermal, and ground-water systems as a means to the more successful exploration for and exploitation of the deposits they have produced. It is the purpose of this paper, therefore, to discuss certain aspects of salt deposit geology as they contribute to exploration and mining through some understanding of ore formation. References to field examples and chemical relations in the salt systems are brief. All examples are more fully discussed, however, in the references cited.

Jan 1, 1970

By Donald E. Steif

The Tower Mill is a vertical stirred mill using steel balls or pebble grinding media. This device is designed for fine grinding at significant power savings when compared to conventional tumbling mills. This paper describes the machine, its operation, application, and performance for wet grinding.

Jan 1, 1984

By Edward F. Oxford

The area described in this paper lies along the inner margin of the Coastal' Plain in Twiggs County, near the exact center of the State of Georgia. Twiggs is one of four counties which produces approximately 75 per cent of the nationals output of kaolin used in the paper trade. In this vicinity the land surface is characterized by coastal plain hills with elevations ranging from about 250 feet, above mean sea level in the flood plain of: the Ocmulgee River to about 550 feet above mean sea level on the hill tops. Surface drainage in the area is southwestward to the Ocmulgee River, the tributaries of which have dissected the land surface exposing thick sections of the upper parts of the hills of Eocene (Ocala Limestone and Barnwell formation) limestone, sand, marl and clay, and in the lower parts of the hills Cretaceous (Tuscaloosa Formation) kaolin, kaolinitic clay, sandy clay, sand and, gravel. The contact between these two principal groups of geologic units is rather easil distinguished as the top of the kaolinitic beds. It is described in detail and mapped in published geologic reports for the area (LaMoreaux, 1946).

Jan 1, 1968

By W. Zhang

"Western China has many shallow coal seams. Mining of these shallow seams contributes to environmental deterioration in part due to disruption of groundwater sources. The lowering of the phreatic surface is attributed to the instability of the impermeable rock groups as a result of mining leading to an increase in permeability and drop in phreatic surface. Underground mining with partial backfilling is one of the fundamental methods of controlling the lowering of the water table in sensitive cases. At present, although significant research has been done in shallow seam mining, there has been no research on the laws governing the movement of impermeable rock groups in partial backfill mining using backfill materials of lower strength. this research, conducted in the Yu Shen-fu region of Western China, developed similar material of sand-based paste filling materials, tested the mechanical parameters of similar material of sand-based paste filling materials, researched on long wall partial backfill mining through similar simulation experiments, obtained the development of “upward fractures” and “downward fracture” under different gap-filling widths and body-filling widths and the movement law of impermeable rock groups under different gap-filling widths and body-filling widths. INTRODUCTION Jurassic coalfield is in the North of Shaanxi province in China, located in border areas of the Maowusu Desert and the Loess Plateau, water resources of Jurassic coalfield in the North of Shaanxi province is meager, ecological environment is fragile (Wang, 2010). With the large-scale development of the mining area, permeable fracture zone will directly affect and spread to the aquifer, causing direct damage to water sources, and lead to the dried up of reservoir, river, wellspring which is recharged by the aquifer(Qian, 2003). There are many researches on aquiclude or impermeable rock groups of shallow coal seam in china, but researches are mainly based on the key strata theory characterized by hard rock as skeleton, without considering the flexibility of impermeable rock groups which is important to reduce the cost of control (Huang, 2010). There are some researches on the stability of impermeable rock groups, but the researches are mainly on permeable fracture zone, which is also called the ""upward crack"" (Wang, 2010), ignoring the influence of the ""downward crack"" on the edge of subsidence basin of impermeable rock groups (Huang, 2010). Previous researches showed that pillar-and-room mining can control the rock crack and surface subsidence (Qiu, 2013), but with the loss of coal resources, and existing disaster a threat of a large scale roof falling. Partial backfill mining mainly by eolian sand bring hope to water-preserved-mining (Fan, 2000), successful practice of paste material backfill mining under buildings and water(Song, 2010)showed its feasibility. Through useing the filling materials with low strength, flexibility and small ratio of height to width, eliminated the threat of a large scale of roof falling, the quantity of partial backfill materials relative to full backfilling are little, the price of sand paste backfilling material is low(Huang, 2011), through designing rational parameters of partial backfill mining, we can achieve the purpose of protecting the phreatic. In this paper, based on the similar simulation experiments, researched on development of the ""upward crack"" , ""downward crack"" and subsidence of impermeable rock groups, researching results can provides the rational parameters to partial backfill mining, and can reduce the cost of filling mining."

Jan 1, 2015

By Rodger C. Smith

The topic chat has been assigned to me ?Economic and Political Climate of the Potash Industry? is a function of two basic facts: 1. Potassium is absolutely essential to plant and animal growth. Along with nitrogen and phosphorus it is one of three major plant nutrients, the three nutrients required in largest quantities for plant growth. 2. United States is unequivocally an "have not" nation with regard to potassium. Quantity of potassium ores is limited and, more disturbing, the cost of production at all U.S. potash mines is marginal in comparison with the major producing countries, i.e. Canada and U.S.S.R.

Jan 1, 1983

By Valerio Violo, Antonio Raschillà, Livia Cicinelli

"The Cityringen project foresees the construction of a new circular metro line in and around the city center of Copenhagen. Both drives, the north and the south one, required the TBMs to be equipped in order to cope with contaminated water table and soil. The north drive mined in water contaminated with chlorinated compounds, including chloroform and vinyl chloride, while the south TBMs excavated in a highly benzene contaminated area, becoming the first TBMs to complete such a challenge. Despite the pollution and the stricter operative procedures, the production has been extremely successful with record up to 520 m in one month and 32 m in one day. 1 INTRODUCTION The Cityringen is an extension of the existing metro line. The 15 km long twin tunnels will form a new circular line with 21 new stations (17 + 4 crossovers). When finished it will interchange with the existing metro, rail and bus infrastructure at key locations around town, taking 90% of Copenhagen citizen at less the 600m from a metro station (Figure 1). The Contract has been awarded in April 2011 to the Copenhagen Metro Team (CMT), a joint venture between the Italian companies Salini Impregilo, Tecnimont and Seli SpA. Tunnels are being excavated with 4 Seli-Kawasaki EPB TBMs, two of which manufactured in Denmark by Seli Tunneling Denmark ApS, which is also operating them. At the moment this article is written 50% of the tunnels have been completed and over 40% handed over for the electromechanical works. Seli Tunnelling Denmark is a Danish company constituted in 2012 as a subsidiary of Seli SpA for this project and subsequently acquired by the Salini Impregilo Group in 2015."

Jan 1, 2016

By P. Roghanchi

The difficulties associated with performing direct tensile strength test lead to development of indirect test methods, which are simple, less expensive, and less time consuming. Splitting tensile strength test (Brazilian test) is performed by applying two opposite concentrated compression load across the diameter of a disk specimen until the failure occurs along the loaded diameter. Theoretically, the load is applied over a small width as a line load, however, by increasing the load, the contact width between the loading jaw and the specimen increases as the specimen deforms. The main aim of this study is to investigate the stress distribution in (1) regular Brazilian specimen in traditional tests with loading jaws and (2) flattened Brazilian specimen with flat platens. A series of the splitting tensile strength tests and uniaxial compression strength tests are performed on three rock types: rhyolite, basalt, and limestone. Further, Numerical modeling studies are performed to investigate the effect of the contact between jaw and Brazilian specimen on stress distribution in the disc specimen based on the results from the experimentation. Finally, the stress distribution in the traditional Brazilian test specimen and the flattened end Brazilian test specimen were compared.

Feb 23, 2014

By H. Soto

As a follow-up to a laboratory study, a pilot scale column for the flotation of coarse particles was designed and then tested in two different applications. In the first test, the concentration of a coarse phosphate ore (normally beneficiated by skin flotation in spirals) was carried out in a flotation plant in Florida. In the second pilot test, the column was used as a scavenger cell in the coarse flotation section of a potash beneficiation plant in Saskatchewan, Canada. Particle size of the phosphate feed was of the order of 0.6-1.0 mm and the potash feed 1-3 mm. The column was 1 feet diameter and was fed at rates between 0.5 to 1.4 tph. The effect of operating variables such as air and water flow rates, bubble size, frother concentration, residence time, sparger, etc were evaluated. The most important factors in column performance were found to be bubble size, air flow rate and the thickness of the froth bed. Best results were obtained in the absence of a froth bed, with low air flow rates and with small bubbles. The paper presents comparative performance and discusses details of the column design. Phosphate recoveries in the column were better than 90% whereas the conventional skin flotation circuit normally yields about 60% recovery for a comparable concentrate grade. Potash recovery from the tailings of the conventional flotation circuit was as high as 42% recovery. Particle size distribution of the potash concentrate was coarse enough to meet requirements for potash fertilizer.

Jan 1, 1993

By S. J. Taylor

The siting, grading and fill usage for leach pads are important aspects of leach pad design. A method is presented that optimizes the cut and fill quantities (i.e. minimizes the cost) required to grade a leach pad with parallel cells; given the desired pad characteristics of maximum and minimum pad slopes, maximum cut and fill depths, etc. and the cut and fill costs. The method allows the variation of the cut and fill costs with depth, which allows the accurate modeling of the cost savings practice of using cheaper fill towards the bottom of a thick fill. This optimization could be incorporated into a CAD package, enabling a designer to simply draw a desired pad shape on a site plan, input the pad and heap characteristics (required heap volume, heap height, heap sideslopes, etc.) and then have the computer report both the adequacy of the pad area and the optimum grading for the particular pad shape. Using this, a designer could quickly and accurately assess the optimum, or cheapest, grading of many shapes and positions for a leach pad. This would be especially useful for large pads that need to be sited on rough terrain.

Jan 1, 1996

By Rustu S. Kalyoncu

Rainbow colors of roofing granules, adorning the roofs of buildings from single family units to largest office buildings, have their origin in the roofing shingles as burlap soaked with tar appearing as early as the 1700s. Dusting of talc and mica on the coated surfaces, to keep roofing from sticking to itself in storage, represents an early improvement to the original construction product. Sometimes, colored, natural mineral dusts were added as color pigments within the dusting material, for initial color. Prolonged exposure to sun caused the asphalt to become brittle, and it eventually cracked and leaked. Search for solutions to cracking and subsequent leaking problems eventually led to the use of crushed mineral granules on asphalt coated shingles. This provided the impetus for further growth in the asphalt roofing industry. Application of a layer of crushed mineral on the asphalt coating minimized the coating deterioration from exposure to ultraviolet light, thus significantly improving the shingle life. In the 1900s, screened waste from slate quarries was the most commonly used granule in asphalt roofing products. Records indicate the use of coarse slate screenings for asphalt roofing as early as 1906. As the asphalt roofing industry further developed, other naturally colored minerals, such as silica sand, quartz, mica, feldspar, talc, slag, granite, rhyolite, and oyster shells were used on roofing surfaces. Later on, a number of manufactured granular materials, such as crushed brick and tile, fire clay, and white porcelain were used. The first artificially colored roofing granule was produced in 1914 by running molten slag into a solution of alkaline metal silicate, which was absorbed by the porous slag. Various colors were obtained by adding pigments to the silicate coating and by subsequently heat treating the granules. In 1922, another technique was developed in which green slate granules were saturated with copper sulfate solution and heated to 760°C to form copper oxide. Since then, many other granule coloring processes have been patented, one of the most significant being the sodium silicate coatings introduced around 1975. Granules as used in construction (specifically roofing materials) are defined as natural or synthetic-mineral grains smaller than gravel and larger than sand in particle size. They are used primarily for protective and decorative purposes on the weather- exposed surface of asphalt composition roofing. Development of artificial coloring techniques has made it possible for the roofing industry to provide asphalt roofing shingles in a wide variety of colors complementing the color and style of buildings. Roofing granules, as we see today, are the products of long technological evolution.

Jan 1, 1994

By William H. Moore

Many of the gravel deposits in Mississippi which range in age from Mississippian to Recent are being exhausted. Particularly in southern Mississippi the supplies will become very short in the near future and some use of sand will have to suffice. All methods of exploration for sand and gravel are presently being used in the State and this will be of some assistance in finding other deposits. A good supply of material for expanded clay aggregates is present in the State and will be sufficient to supply the needs of this segment of the construction industry for years to come. Crushed stone has been a minor contributor in years past and will probably become no more important in the future.

Jan 1, 1979

Machine breakdowns and maintenance delays are large contributors to lost production and increased operating costs in the mining industry. The US Bureau of Mines is investigating the applications of expert system technology to diagnostic and predictive maintenance for mining equipment. This will help increase mining productivity and decrease operating costs by reducing the frequency of equipment failures and repair times. The Bureau has begun this effort by applying expert system techniques to the diagnosis of hydraulic system problems on a continuous mining machine. This paper discusses the development of the hydraulic diagnostic expert system.

Jan 1, 1992

By R. B. Lantz

Low Froude Number (Fr) theory* predicts that stably-stratified fl& around a terrain obstacle will divide into a lower layer passing essentially horizontally around the obstacle and an upper layer passing essentially over the obstacle. The prediction was formulated by Sheppard (1956) and Drazin (1961) and confirmed experimentally in the towing tank model d experiments of Hunt et a1 (1978) and the atmospheric full scale experiments of the US EPA Complex Terrain Model Development Program (1982- 1985). The US EPA Complex Terrain Dispersion Model, currently under development, employs the layering principle with the flow in each layer calculated independently by potential flow (PF) theory after the layer thicknesses are established according to a simple function of Fr, i.e., Hc /H = 1 - Fr where Hc is the dividing streamline freight and E is the obstacle height. Use of PF theory in the CTDM is attractive because numerical solutions can be obtained simply and economically, as compared to lengthy Navier-Stokes (N-S) solutions, but realism is sacrificed in creating a surface of discontinuity between the tm layers and eliminating the effects of shear and gravity in each layer.

Jan 1, 1986

By S. V. Krishnan

In the upgrading of finely-disseminated iron ores, selective desliming is the critical step which must be controlled in order to achieve efficient flotation. A prerequisite for selective desliming is a properly-dispersed pulp; sodium silicate is commonly used as a dispersant. The mechanism by which sodium silicate acts as a dispersant in the presence of calcium ions was examined by streaming potential measurements, settling tests, abstraction density determinations, selective flocculation tests and scanning electron microscope observations. The study established that calcium silicate precipitates on the mineral surfaces dispersed the pulp. Although sodium silicate was a nonselective dispersant, the addition of corn starch aided the flocculation of goethite over quartz at low silicate additions, but became ineffective at higher silicate levels. A model is presented to explain the dispersant mechanism of sodium silicate in the presence of calcium ion for selective flocculation of iron ores.

Jan 1, 1982

By J. S. Jaspal

Mining of thin coal seams is both difficult and uneconomical. As a result, most of thin-seam coal reserves in the U. S. are not being mined. It is estimated that nearly 910 Gt (K. Unrug, 1985) of coal reserves exist in 355 to 710 mm thick seams. The Bureau is attempting to develop new techniques for mining 150 to 1065 mm thick coal seams. This paper summarizes the research work on existing thin-seam mining techniques, testing on small and full scale physical models of the Bureau slot mining concept, and computer modeling of the full-scale process.

Jan 1, 1992

Mill #4 processes mildly refractory ore from Carlin Trend deposits. Diagnostic analysis of plant operating data was used to generate a mathematical model containing the key parameters influencing the gold recovery. The model was used to direct modifications to plant operating practice. The cyanide dosing strategy was changed to reduce preg-rob gold losses and cut reagent consumption A finer grind was achieved without capital investment. The density in CIL was lowered, and tighter control was exercised over plant throughput. These changes resulted in a recovery increase of at least 2%, worth $111,000/month at $300/oz, and concomitant reagent cost savings of $55,000/month.

Jan 1, 1999

By A. E. Stewart

Slope design in an open pit mine includes determining bench height, bench face angle and berm width. Case histories are presented of two highwall slopes (160 and 220 m or 525 and 720 ft high) excavated in dipping strata in an op¬erating coal mine. These examples illustrate the influence that bench face angle can have on the stability of an entire slope. The two highwall slopes, the lower of which experienced significant instability, were excavated in approximately the same lithologic and structural environment. The main differences between the slopes were the angle at which the bench faces were excavated and the excavating methods that were used. Relevent aspects are also described of the engineering geology, slope design and excavation procedures.

Jan 1, 1998