Search Documents

By Dr. George W. Annadale, Dr. Adrian G. Chantler

Materials which are likely to produce Acid Rock Drainage (ARV) can be identified with a reasonable degree of certainty. However, it is not currently possible to predict the concentrations of future contaminant discharges with similar confidence. One way of overcoming this problem is to model the uncertainty in knowledge related to estimates of future contaminant concentrations, and utilize this information in a decision model to decide on acceptable levels of expenditure on ARV control measures. The paper presents a risk modeling approach and proposes a decision model.

Jan 1, 1992

By L. B. Rothfeld

This paper presents preliminary results of a Bureau of Mines study of potential costs of compliance with the federal Resource Conservation and Recovery Act for copper heap and dump leaching. Specifically, estimates are given for the cost of compliance with possible technology standards that would require the use of liners and closure caps regardless of terrain and underlying geology and hydrology. This cost is compared to the co lit of compliance with present state requirements for terrain a typical of those found at existing copper leach sites in the Southwestern U.S.A. Incremental compliance costs are found to widely exceed screening criteria used by the Environmental Protection Agency to denote significant economic impact.

Jan 1, 1993

By Yuexin Han

The characteristics of comminuted hematite products using a high pressure grinding roller (HPGR) and conventional jaw crusher (JC) were comparatively studied by screening, optical microscope, scanning electron microscope (SEM) and Brunauer, Emmett and Teller (BET) techniques. Major properties investigated included product size distribution, particle cracks, specific surface areas and pore volumes. Results showed that in a closed-circuit operation with a screen opening of 3.2 mm, the HPGR and JC gave a similar P80, but the HPGR achieved a more uniform size distribution, more fines and a higher crushing efficiency. Three modes of cracks were identified, namely transgranular cracks, innergranular microcracks and intergranular microcracks. Transgranular cracks originated from shearing breakage. Innergranular and intergranular microcracks were generated by HPGR via the two main nonrandom breakage forms, preferential breakage and interfacial breakage, depending on their respective ability to endure stresses when mineral phases (particles) were loaded against each other. The BET values for the same-size fractions showed that HPGR products gave higher specific surface areas and more pore volumes than JC products. This indicates that HPGR-crushed products are easier to grind because of their high porosity and extra cracks.

May 1, 2012

By Swan. J. D.

Repairing and replacing equipment damaged by corrosion and abrasion is a major cost throughout industry, especially in the coal mining industry. Careful study of corrosion and abrasion, and their causes and effects, often leads to the selection of alternative materials which can provide economies. What, actually, are corrosion and abrasion and how do they contribute to the cost of operating a coal-preparation plant? Furthermore, what can be done to alleviate corrosion and abrasion problems and thereby reduce operating costs? These questions will be answered in the following discussion, which will describe the destructive action of corrosion and abrasion and give several methods for controlling corrosion and abrasion losses, These methods include the substitution of stainless steel for carbon steel, the use of corrosion inhibitors, and the use of design to eliminate corrosion and abrasion. Examples will be given illustrating the benefits that have resulted in plant tests when these methods of controlling corrosion and abrasion were used.

Jan 1, 1970

By Joern Katzer

It is vitally important to any tunnel project to have an accurate and reliable survey control network inside the tunnel for layouts, as-built surveys, and to provide guidance to the tunnel boring machine (TBM). However, the concepts and methodology to provide such a survey network are sometimes not well understood. For example, the first anticipated survey task that takes place during the bidding process is often ignored, which is to provide a comprehensive survey network preanalysis for the surface network and tunnel traverse based on survey statistics that will be used to make informed decisions on the survey requirements and methodology. Instead, these steps are often only vaguely based on previous results and prior tunneling experience. But each tunnel is different, and a solution that worked for one tunnel project might be unsuitable for another. The purpose of this paper is to provide tunnel project engineers, managers and surveyors with the general concepts for tunnel survey methodologies and examines several statistical tools for a basic horizontal and vertical tunnel survey preanalysis. These survey statistics tools provide useful estimates of the expected lateral and vertical tunnel traverse accuracies, but are not a replacement for a comprehensive tunnel network preanalysis. The proposed formulas do not take centering errors into account, are using average distances for each traverse leg, and assume that the survey data is free of outliers in the measurements. It is very important that the estimated instrument accuracy is based on true values that are reflective of measurement precisions that are actually achievable inside the tunnel to provide accurate results.

Dec 1, 2022

By M. Moats

Copper electrowinning operations have dramatically improved their ability to produce high quality copper at low costs over the past several decades. Even so, some fundamental knowledge is still lacking that could allow operations to run even more efficiently. For example, a rule of thumb exists that estimates a current efficiency loss of 2-3% per gram per liter of iron in the electrolyte. While several laboratory studies have been performed that demonstrate this rule of thumb is likely true, no definitive relationship exists. In this paper, the first steps in developing a definitive relationship are presented. The effective diffusivity of ferric ions in synthetic copper electrowinning solutions was measured using chronoamperometry and the Cottrell equation. The effective diffusivity of ferric ion was determined as a function of electrolyte concentration and temperature. Synthetic electrolytes were then used in laboratory-scaled copper electrowinning experiments, where relationships between current efficiency and solution composition were found to exist under stagnant conditions. Key words: Copper electrowinning, Current efficiency, Chronoamperometry, Ferric ions

Jan 1, 2009

The Gosowong epithermal quartz-adularia vein, in the Halmahera magmatic arc, is a new discovery in an area of primary tropical rain forest with no history of gold mining or mineralization. The newly recognized mineral district also contains a number of other epithermal vein systems, two centres of porphyry Cu-Au mineralization, and a number of argillic and advanced argillic alteration zones that may be related to underlying mineralization. Gosowong was discovered and tested through the application of basic exploration techniques including drainage sampling, soil sampling, trenching, magnetics, IP, and diamond drilling. Lapse time from the initial reconnaissance discovery of a stream sediment anomaly to the release of inferred resource estimates of approximately 1.0m ounces was just over 3 years.

Jan 1, 1997

By A. F. Peterson

There is no single mining problem at Benson that does not exist at some other mine. There are four, however, that require special attention primarily because they occur together and have an influence on each other. These are the nature of the mineral occurrence, the shape of the ore body, the operating schedule, and the climate. It is the purpose of this paper to describe mining practices in relation to these four factors. Iron ore was first noticed in the Star Lake area early in the nineteenth century. Prior to Jones and Laughlin leasing the facilities built by the Defence Plant Corporation, several companies tried to mine the ore body but gave it up as uneconomical. While there is a little high grade (40%) magnetite, most of the ore contains 20 to 25% iron and not enough was known prior to World War II to design a profitable operation. By 1943, and certainly in the years that followed, technological developments in ore dressing and mining not only put the magnetite into the category of a commercial ore, but made possible the concentration of the non-magnetic iron mineral, martite. This last development nearly doubled the ore reserve. Jones and Laughlin bought the DPC holdings in 1946 and has since expanded the plant to its present capacity of 4,400 gross tons of concentrates daily or 1,600,000 gross tons per year. Magnetite makes up 62% of this production at the present time, but it will be necessary before long to bring martite production up to about 45% of the total because of the ratio of the two ores in the reserves. To keep the plant supplied, 14,000 to 15,000 tons must be mined and crushed daily, with a ratio of concentration that varies from 2.8 to 3.4. The ore body is 12,000 feet long and varies in width from 600 to 1,500 feet. The waste rock is, for the most part, a granite gneiss, and the overburden, of which little is left, is a glacial drift sand. For the entire reserve, there is a half ton of rock for every ton of concentrate, but the stripping ratio is more than one to one at present because of the existence of more rock in the upper mining levels in relation to the ore. The dirt stripping or development work that cannot be handled by company facilities is contracted to an outside firm. The need for this diminishes every year and will soon disappear. The deposit looks like a "J" in plan, with the long leg running approximately north and south and the short leg to the west. The primary crushing plant, consisting of a 54" gyratory followed by two 18" gyratories and a 1,500 foot conveyor belt to the fine crushers, is located on the third level where the long and short leg of the mine meet. The widest part of the pit lies just the north of the crusher. The mine is operated on a lease that expires in 199l0 There are two fee owners, the Benson Iron Company, which owns slightly overhlf of the reserves, and the Newton Falls Paper Company, which owns the balance. There is no appreciable difference in the mining on the two fees, so the ore is removed in strict proportion to calculated reserves during each year. Basic mining equipment consists of eight 45 yard electric shovels, a fleet of twenty-five 22 ton end dump trucks, eleven churn drills for nine inch blast holes, and two small percussion drills for four to five inch holes, There are the normal auxiliary items, such as dozers, graders, wagon drills, and two drop-ball cranes. Power is purchased and, where practical, is used at 4100 volts. Pit drainage pumps can handle a maximum of 11,500 GPM from the several sumps, but water is a problem only during the spring or when a sudden thaw follows a heavy snowfall.

Jan 1, 1958

By Yoginder P. Chugh, K. V. K. Prasad, R. Missavage

This paper presents results of field monitoring and finite element studies to analyze and improve a room-and-pillar retreat mining system. Fie1 d instrumentation was utilized to monitor pi11ar load changes, roof to floor convergence and differential roof strata movement as retreat mining progressed and to determine in-situ horizontal stresses. A two-dimensional finite element model depicting strata behavior at this mine was developed and used to analyze existing and alternate improved mining geometries. The results showed excellent correlation between fie1 d observed and model predicted behavior. Some of the recommended changes in mining geometry based on the study were incorporated in the mining system.

Jan 1, 1986

By A. R. Zambrano

Equations for power draft, capacity and work input for predicting the performance of industrial grinding mills are derived based on torque measurements using a laboratory instrumented mill. These derivations are based on mechanical principles and on the first-order kinetics of the grinding process. Rittinger's, Kick's and Bond's laws express work input as work index (Wi) times a particle size function. It is proposed that these laws are only particular cases of more general expressions having the particle size function raised to an exponent, i.e., the work exponent (We). Case studies illustrate the excellent prediction of the Wi - We models compared to the three mentioned laws, and, from the data, the corresponding general mill-sizing equation is derived. Key words: Grinding mills, Comminution, Work index, Mill sizing

Jan 1, 2003

By Toyohisa Fujita, Mitsuo Mamiya, W. Tai Yen, Hiroki Kogita

Green algae taken from an acidic mine drainage and blue-green algae taken from an alkaline hot spring stream were collected and tested for their ability to recover or remove dilute metal ions. Experimental results demonstrated that unwashed blue-green algae and washed green algae effectively adsorbed base metals ions and eluted them at pH 1. It was also found that washed and dried algae adsorbed precious metal ions more effectively than unwashed algae. For example, the washed and dried blue-green algae was capable of adsorbing 0.31 kg of gold per kg of algae. The gold from tetrachloroaurate solution which was adsorbed on washed blue- green algae was found to change to a metallic state following initial metal binding. In the case of a dilute gold complex solution leached with thiourea, only a small amount of gold could be captured by algae. Further experiments were conducted on components of the algae, such as alginic acid, agar, cellulose and chitin and mixtures of these components, in order to determine their contribution to metal adsorption characteristics. However, a mixture of these two components demonstrated both good adsorption and desorption characteristics indicating an interaction between the individual components.

Jan 1, 1995

By John A. Herbst, William T. Pate, Ruben Tello Flores, Humberto Arreola Zarate

Plantwide control is the networking and coordination of individual control systems throughout the plant to enhance plant performance. The high level decision making involved in this coordination is used to achieve overall plant optimization. Decisions must be based on knowledge and information moving between control systems in both downstream and upstream directions and on management information systems containing financial data on the impact of coordinating actions. For example, certain quantitative descriptors of upstream operations are passed to the downstream control systems to prepare those operations for the feed material they will receive. Likewise, other quantitative descriptors of downstream operations are passed to upstream control systems to modify their output. In this case, setpoints are determined throughout the plant which maximize profitability, given current ore conditions and plant operating constraints. Due to the wide area coverage of this coordinator, it is forced to draw on several diverse information and knowledge bases. Such a coordinator, then, must rely on a combination of heuristic logic, model-based control and neural networks to unify the knowledge bases as well as to take advantage of their strengths and to compensate for deficiencies. A description is given of control systems for primary and secondary grinding and flotation at a large copper concentrator and how they are being integrated to achieve plantwide control. Financial implications are discussed.

Jan 1, 1995

By A. P. Massmann

Design for economical operation, minimum operating labor and minimum maintenance for labor and supplies are virtually inseparable. Each consideration has a vital bearing on the other. Let us assume that we have the design complete for the most economical operation with a minimum of operating personnel. This means, in addition, that we have the fewest number of operating units consistent with the product requirements for a team or metallurgical coal which we are called on to produce. The number of units will vary greatly, being influenced by design, washability characteristics, tonnage and degree of quality control necessary by reason of producing a product for metallurgical, steam or domestic use. The units involved most ordinarily for any type coal preparation plant will number as a minimum the following: 1. Hoppering R.O.M. Coal 2. Feeding

Jan 1, 1959

By Ernest M. Spokes

Maximum fan efficiency can only be obtained when the fan has the correct combination of size, speed, and blade setting to provide the required flow of air against the mine resistance. As the mine grows older, resistance decreases unless old workings flow is restricted, and new combinations of speed and blade setting or different fan sizes may provide greater economy.

Jan 1, 1977

By F. H. Mertens

The costs of an open-pit operation can be classified according to the following hierarchy : -overall cost of production (per ton of ore) -costs of basic operations and functions -costs of auxiliary operations -costs of machines and equipment -maintenance costs. Production cost is a measure of the open-pit mine performance and should be the final target of the management control. It is also a measure of the share of the mine in the processing stages.

Jan 1, 1990

By D. W. Park

Longwall mining is considered the most efficient underground coal mining technique in terms of coal extraction ratio, production rate, and safety standards. Due to the increasing demand for higher coal production, wider panel and faster face movement have become the recent trends. Thus, longwall mining can create unexpected threats such as roof falls, excessive face convergence, shield damage and numerous maintenance problems causing sudden interruption of coal production and serious safety hazards. A recent study at the University of Alabama is dedicated to develop LoSCoMS (Longwall Strata Control and Maintenance System) which integrates real-time shield monitoring, data presentation, analysis, forecasting, and warning modules. The main objectives of this system is to provide the stability and maintenance information, at every minute, such as high load, low setting pressure, leg leakage, etc., analysis of various mining and geological parameters to determine past and present roof characteristics and forecasting of loading patterns for the following mining cycles, next periodic weighting, etc. Using this unique system, mine operating personnel are well aware of past, present and future roof loading patterns at the longwall face, and thus, proper safety measures can be taken ahead of time.

Jan 1, 1997

By W. J. Garmoe

The Carr Fork mine is located approximately 50 kilometers southwest of Salt Lake City, Utah, in the Bingham or West Mountain District, adjacent to the Bingham open pit copper mine. Applied geology at Carr Fork, by Anaconda Minerals Company personnel, includes detailed geologic mapping and sampling of underground workings, logging and sampling of drill core and cuttings, and the preparation and posting of geologic maps and cross sections for geologic interpretation, ore reserve calculation, mine operations, and long range planning. Accurate and easily understood graphic recording of Carr Fork geology is essential for optimum use by operating and engineering personnel. The design and implementation of exploration, development and definition drilling programs, research into geological spatial relationships, and analysis of structural complexities of the Carr Fork deposit are also integral parts of the applied geology program.

Jan 1, 1992

By Uday Kumar

This paper presents details of an availability study for a fleet of diesel engine operated load-haul-dump (LHD) machines used in a Swedish mine. For the purpose of this study, the LHD machines have been considered as a system comprised of many subsystems like engine, brake, transmission, etc., in series. As availability is dependent on both the reliability and maintainability characteristics of the system, together with reliability, the concepts of maintainability are also discussed. The need for exploring the data for the presence of any structure, which is very common in repairable system data sets, is emphasized with suitable examples. Simple graphical techniques are used for verifying the independent and identically distributed (IID) assumption for the data set. The error introduced due to the use of the exponential distribution in place of more appropriate distributions in estimation of availability and reliability characteristics is analysed.

Jan 1, 1989

By J. K. Wolski

This paper addresses the effects of using jet fans as booster fans in mine ventilation networks. A method was developed to determine the pressure generated by jet fans using the momentum theory. The influence of a reduction cone and other ventilation parameters on the jet fan pressure was analyzed. Verification experiments conducted in the Waldo Mine are described. Examples are given to demonstrate the conditions for the effective use of jet fans.

Jan 1, 1998

By T. M. Yegulalp

A short review of the current practice and recent developments is followed by a description of a newly developed approach for the solution of the optimum ultimate pit limit problem. The new approach utilizes the network modeling of the problem for solution by maximum flow algorithm. The latest developments in the implementation of maximum flow algorithm present significant time and memory savings as compared to initial development due to Ford and Fulkerson. Results of a series of computational tests are presented to demonstrate how this approach performs as compared to the well-known Lerchs Grossman algorithm. It is also shown that the solution by the new method will automatically include several optimal solutions based on predetermined number of benches to be included in the analysis.

Jan 1, 1993