Search Documents

By K. Bunney

A high-pressure laboratory elution rig was commissioned to simulate industrial Zadra and AARL elution conditions for the stripping of gold, silver and mercury from loaded activated carbon. It was found that cyanide was essential for the efficient elution of both mercury and silver, while gold was found to elute most effectively in hot, low-ionic strength solutions. Therefore, the standard AARL-type elution, which implements a cyanide soak and water elution, results in a lower recovery of mercury and silver from the carbon. No single set of conditions was found whereby gold, silver and mercury can all be effectively eluted in a single step. However, sequential elution conditions can efficiently recover all metals and provide a potential approach for separating these metals.

Jan 1, 2010

By Gabino Preciado, Louis Sandbak

Corrosion has long been identified as a potential risk to the long-term ground support stability due to degradation of internal ground support elements such as rock bolts but also to surface support from mesh, straps, bolt plates, and ancillary support of utilities such as hangers. The emphasis is to understand the corrosion mechanisms on the primary ground support elements and any supplemental steel or arch sets. The water and chemical processes from oxidation(rust), stress corrosion cracking, and even the electrical charge created during these reactions contribute to the corrosion of the steel support elements. The main goals are to mitigate the effects of corrosion and to be able to predict those areas of high water or high sulphide for potential rehab maps. It is also essential to identify and classify the visible corrosion as part of damage mapping and provide bolt testing to those areas of suspected internal damage from corrosion. This is important to get an estimate of the support longevity or expected life before rehab to minimize the overall cost of the operation.

Feb 1, 2024

By Richard J. Fantel

This paper addresses the impact of declining world rutile resources upon the production of titanium products and their asso¬ciated costs. Titanium is used primarily for the production of pigments; in its metal form it is considered a strategic and critical material to the U.S. defense and aerospace industries. There are two major mineral sources for titanium: ilmenite and rutile. Both these mineral types can be used to produce titanium pigments. Only high grade titanium concentrates, such as rutile, high-grade ilmenite, and synthetic rutile (which is produced through further processing of ilmenite), can be used in the production of titanium metal. This paper draws upon the data and analyses of a recent Bureau of Mines Minerals Availability Program appraisal that evaluated the international availability of titanium from market economy countries. The paper will show that production from economic rutile mines will decline sometime after the turn of the century and that rutile shortages could be alleviated by production from other high-grade titanium resources such as higher cost rutile deposits and anatase deposits, or through an increase in world synthetic rutile capacity.

Jan 1, 1984

By David J. Kruse

The proper modeling of granular flow using discontinuum mechanics has the potential to be one of the most significant scientific advancements in the mining industry today. This paper will examine the status of discrete element technology, specifically focusing on current and future applications. The fundamentals of the Discrete Element Method (DEM) will be briefly introduced, as well as relevant design parameters. Various types of granular flow problems currently being solved using the DEM methodology will be presented. The results and potential benefits of these cases will also be discussed. All simulation results and figures used throughout this paper are from studies and designs preformed by the DEM group at Conveyor Dynamics, Inc. (CDI).

Jan 1, 2000

By Colin Lawrence

The Port of New York and New Jersey is one of the most heavily used transportation arteries in the world, handling nearly 40 per-cent of the North Atlantic shipping trade and directly providing nearly 230,000 jobs to the local economy. In 2004, $100 billion worth of consumer goods moved through the port. To accommodate future cargo volumes in the port, which are expected to double over the next decade and possibly quadruple in 40 years, deeper shipping channels are needed to provide access for a new generation of cargo mega-ships with drafts exceeding 13.7-m (45-ft) when loaded. Current channels within the harbor range in depths up to 13.7-m (45-ft), thus preventing carriers from using these larger ships, or requiring significant reductions in cargo to achieve lesser drafts to operate safely within the harbor. As part of the Harbor Deepening Project, the Anchor-age Channel would be deepened to 15.2 m (50 ft) below mean low water (MLW), for a length of 5,790 m (19,000 ft). The New York City Department of Environmental Protection (NYCDEP) owns, operates and maintains two existing water siphons in the harbor. Due to their shallow depth, both existing siphons must be relocated before dredging of the Anchorage Channel can be completed. Tom Costanzo, manager of capital programs for the Port Authority of New York and New Jersey (PANYNJ), says that ?While the re-location of the existing siphons under the Anchorage Channel is vital to the success of the deepening program, it is also a story of cooperation among key agencies at different levels of government resulting in improvements that will benefit the people of this region greatly.?

Jun 1, 2010

By W. Hu

Gravity concentration has been the main method for tin ore beneficiation, based on the significant difference of density between cassiterite and gangue in the tin ore. However, with the exhaustion of rich and coarse reserves, the proportion of tin distribution in slime be-comes as high as 50 to 70% and has a size range of -19 urn. In some sulfide tin ore, most of the tin is of the minus 10-urn size fraction, and thus slime processing has gained importance in tin ore processing. Some innovations are being developed, such as the centrifugal cone separator, belt concentrator, slime table, B-M separator, and slime flotation. Direct flotation with tolyl arsonic acid has been practiced with success.

Jan 1, 1989

By Rolph Linder

It is generally known and accepted that the efficiency of the blast furnace process, expressed by the symbols specific production and coke consumption, is influenced by a large number of variables connected to the type of burden, the alloy contents of the produced iron and the conditions of production as composition and preheating of the blast, the furnace heat losses and the possible use of fuels added on the tuyere level. It is furthermore obvious, that the coke consumption of the process will be influenced by specific production which could be said to be the result of two counter-acting influences. With high production, realized through intensive blowing, the passage time of the ore through the furnace is shortened leading to a decrease of the indirect reduction taking place in the upper part of the shaft within the temperature range of 300 to 1000°C. Simultaneously the external heat losses (constant in time) will be smaller calculated on each ton of iron and the resulting change in coke consumption will be the effect of both those influences. It is certainly of interest to be able to predetermine the effect of those variables before a change in the production practice is carried out.

Jan 1, 1964

By Sam S. Arentz

Storm King Mines began with the concept that the resource potential of thick and steeply pitching seams of the Grand Hogback region of Colorado could be mined profitably. Two large tracts of private land (fee coal) were acquired; approximately 23.8 km2 near Glenwood and 16.2 km2 near Meeker. Figure 1. Although both properties have substantial coal reserves, one has several distinct advantages in developing a competitive mining operation. Table 1 illustrates these advantages. Among the most important considerations from an economical point of view are proximity to railroad, highway, labor force, quality of coal, seam thickness, and source of water. As can be seen, Storm King Mines' property is adjacent to the main line of the D & RGW Railroad, 1-70, and the Colorado River. The cities of New Castle, Glenwood Springs, Silt, Rifle, Carbondale, and Parachute are within short commuting distances and have available skilled labor.

Jan 1, 1983

By Cheng Zhengbing, Sun Baoqi

This paper summarizes several chemical purification methods used for producing high-pure industrial minerals These methods, mainly including alkali melting, acid leaching, oxidation-reduction bleaching, are respectively used to eliminate the impurities such as silicates in graphite and diamond, ferric oxides in quartz sand or other valuable silicate minerals, colouring impurities in kaoline, barite and other minerals which are required to have a high-whiteness. The fundamentals of the chemical purification methods and some practical examples in China are introduced in the paper.

Jan 1, 1995

By W. J. D. Stone

In 1960, Magnetics International Ltd. undertook the development of the Jones High Intensity Wet Magnetic Separator in the Americas. Magnetics International had a number of possible applications in its own projects plus the intention of developing the equipment for sale to others. It was soon recognized that no matter how innovative a piece of mineral separation equipment may be, it takes many years and much finance before it is finally accepted for large scale use. For this reason, many good ideas die in their infancy. One of the chief reasons for such a time lag between conception and large scale implementation is the usual lack of finance to construct and put into operation a large demonstration unit. Even with a large unit for demonstration, the first major user usually requires a guarantee that is not normal in accepted separation equipment. Such problems are also normally accompanied by major design changes from the first conception.

Jan 1, 1971

By Richard Chojnacki

The western united States is not usually noted for the production of fluorspar; however, many significant fluorspar districts do occur in the Rocky Mountain region and constitute a resource of sizable dimension and major potential. This is particularly true within the area of the West served by the rail lines of the Union Pacific Railroad (see Figure 1). Fluorspar deposits near the Union Pacific have produced over 1.3 million tons of finished fluorspar products from 2.3 million tons of ore. Approximately 80% of this production was of acid-grade and 20% of metallurgical-grade fluorspar. Production of ceramic-grade was negligible. Through the years substantial production has come from eight mining districts. Five of these have produced metallurgical-grade and three acid-grade. The best-known fluorspar producing area in the West is the Jamestown Mining District. It was one of the first producers of fluorspar in the western United States and is estimated to have produced over 500,000 tons of finished fluorspar from over a million tons of ore. The district encompasses approximately 36 square miles in central Boulder County, Colorado, about 9 miles northwest of the City of Boulder. Although small shipments were made from the district as early as 1873 or 1874, significant sustained production was not achieved until 1940 when the General Chemical Company, now a division of the Allied Chemical company, acquired the Alice, Burlington, Chancellor,

Jan 1, 1971

Considerable attention has been given to the restoration of low-level radioactive (<1000 pCl/g) sites contaminated during the early years of the atomic energy program. Current clean-up activities which involve the relocation of contaminated soils to licensed disposal sites have been shown to be very costly due to the large volumes of soils which must be excavated, transported and stored. Recent characterization studies conducted at Virginia Tech suggest that the volume of soil requiring disposal can be greatly reduced using mineral processing techniques such as classification, density separation and froth flotation. This article discusses the application of these technologies for soil remediation and describes a conceptual flowsheet for treating soil samples from two contaminated sites.

Jan 1, 1997

By Douglas G. Hubert

To put coal in its proper perspective as a source of energy for electric power production, we must first compare it to other energy sources. A report of the Atomic Industrial Forum dated February 1958 records a number of authoritative though widely varying predictions. The most optimistic of these states that by 1968 there will be a total U.S. capacity of about 6000 megawatts of nuclear power, if growth continues at the present rate. Other sources indicate over 200,000 megawatts of total electrical capacity in utility plants by 1968. This is only 3% nuclear. Therefore, 97% of our total power production will be from non-nuclear energy. Fig. 1 shows the distribution of energy sources of electric utility product- ion in the U.S. as reported by the Federal Power Commission in 1954. Note that less than one quarter of the total is hydro and about one half of the total is coal. For 1957, the Edison Electric Institute reports that of the total steam- electric generation in the U. S., 68.6% was by coal, 7.9% was by oil and 23.5% was by gas. This is an increase for coal and a decrease for oil and gas in those three years. Thus we can conclude that two-thirds of the steam-electric power in the U. S. is now generated by coal. Fig. 2 shows the major markets for coal for 1947 vs 1957. The greatest in- crease has been in the electric utility market, where it has more than doubled in the ten years. One-third of the total coal produced goes to the utilities which now represent coal?s major market. Utilities used 160 million tons of coal in 1957, and the estimated quantity for 1967 is 275 million tons, and for 1977 is 525 million tons. It is predicted that 85% of steam-electric power will be generated by coal in 1975.

Jan 1, 1959

By Jacques B. Wertz

Recurring movements remotely connected with the Murray fracture zone and the San Andreas fault complex, together with the slow northwestward drift affecting the Baja California peninsula, could progressively have accentuated the tensional situation already connected with the anticlinorium in southern Arizona. From the fragmentary data gathered on the Texas lineament, it appears that a very mild curvature, concave to the northeast, may be present along this belt throughout Arizona. Those localities where the successive changes in direc¬tion of the strands of the lineament belt seem to occur do generally coincide with intersections of both north-northwestern and northeastern breaks. It is along the outward, southern fringe of the belt (at such structural centers like Bisbee, Baboquivari, Ajo) that the greatest impact of regional movements could be expected to have occurred through tangential-torsional stresses. Although it si accepted that the north-northwestern and more particu¬larly the northeastern fractures in Southeast Arizona are propitious to or partially responsible for mineralization, it seems undeniable that the Texas lineament belt must have greatly increased the potentialities for ore throughout the Arizona copper province. While intrusive bodies occur near major intersections, with the Texas lineament belt as a common denominator, it seems, the ore deposits are to be found close to one of the intrusive stocks, varying in distance from contiguity (Bisbee) to one or two miles away (Silver Bell orebodies).

Jan 1, 1970

By D. P. Patil, B. K. Parekh

Water is the mainstay for beneficiation of fine size coal and minerals; however, it is also the least desirable constituent in the final product. The basic concept of the novel process described in this paper is based on the differential surface heat absorption capacity of individual particles, which differs for different species of mineral. When a mixture of fine material is exposed to a radiant energy source, the various solids components present in the mixture will absorb heat energy depending on their composition and there will be difference in the surface temperature of the particles. When this differentially heated solid mixture is placed on a moving belt, which is coated with low temperature melting resin, the hotter component of the mixture will stick to the belt and relatively cooler will stay free on the belt and fall off at the end of the belt run. Experiments were conducted with pyrite, coal and quartz of 6 x18 mesh particle size. The goal of the test program was to find the optimum conditions at which there exists a required temperature difference between minerals and coal particles by controlling the operating and system variables. Preliminary tests results showed that there is a potential for separating mineral matter from coal using the thermo-adhesive separation technique.

Mar 2, 2022

By N. Finkelstein, C. G. Palagi, S. S. Stillar

The C. E. Weed concentrator treats 51,000 tons per day of 0.5% to 0.7% copper ore received from the Berkeley Pit, the Continental East Pit and the Butte underground mines. Improved operating techniques and conversion from semi-autogenous secondary grinding to ball milling have increased tonnage from an original design of 42,000 tpd. Separate treatment of sands and slimes, with recovery of soluble cop- per from the slimes, has increased total copper recovery. Concentrator tailings are pumped 600 vertical feet and 20,000 horizontal feet for disposal.

Jan 1, 1976

By A. B. Cecala

The US Bureau of Mines performed a study to determine optimal locations for longwall face methane monitoring equipment. Longwall face ignitions continue to be a concern to the US coal mining industry. Gains in ignition control technology have been somewhat negated by advances in longwall productivity. More reliable, heavy duty longwall face systems generate higher production rates and increase methane liberation rates. These rates will likely continue to rise as further coal production increases occur. Efforts will continue in the areas of methane drainage, methane containment and methane dilution. In addition, more effective face methane monitoring is needed. As technology continues toward automated longwall panels, the importance of monitoring for methane at the shearer becomes even more significant. Since the primary face ignition source is the shearer mining machine, the Bureau ran tests to determine the best location to take methane readings on the shearer. This information, in conjunction with data obtained from field studies, provides a knowledge base for selecting optimum face methane monitoring locations.

Jan 1, 1995

By T. A. Doyle

Column and batch test methods are used to simulate and model the leaching of various mining by-products. Batch tests are simpler, while column tests more intuitively represent the field conditions to be simulated. Projects that have included different types of leaching tests illustrate the strengths, limitations, and associated uncertainties of each. Column and batch tests have been used to evaluate arsenic solubility in leachate from treated copper smelter flue dust, to simulate the leaching of pit wall rock from a proposed gold mine, and to simulate the release of uranium from aquifer materials.

Jan 1, 1998

By M. D. Bath

Minproc Engineers Inc. (Minproc) recently completed the construction and start-up of a process facility to treat 14,000 t/d of gold-silver ore at Kori Kollo, Bolivia. The comminution circuit consists of crushing and SAG-ball mill grinding. Breakage characteristics of the ore were determined and a circuit model developed. This enabled variations of the circuit to be simulated, and evaluated in terms of predicted performance to provide the criteria for final engineering design. Subsequently, analysis of the operating circuit provided data for circuit model-fitting. The validity of the original model and circuit performance predictions are discussed.

Jan 1, 1994

By Laurindo De Salles Leal Filho

Microflotation tests with sodium oleate, in alkaline pH, were performed with apatite and some silicates (phlogopite, quartz, and chlorite) that commonly occur in Brazilian phosphate ores. Further flotation tests were carried out with selected ores containing the same silicates as important gangue minerals. The results showed that apatite recovery is highly affected by competition with silicate minerals, probably activated by calcium ions dissolved in flotation pulp. Inorganic chemical species (sodium tripolyphosphate, sodium carbonate/ bicarbonate, and carbon dioxide) that could act as water softeners were used as modifier agents. They proved to be capable of improving flotation recovery and selectivity.

Jan 1, 1999