Search Documents

By H. W. Judges

A 16.5-kt/day underground molybdenum mine is being developed at Questa in Northern New Mexico by Molycorp, Inc., a wholly-owned subsidiary of Union Oil Company of California. Construction of the underground mine began in 1979, and first production is scheduled for early 1983. A gravity block caving method has been selected for mining the ore. Access to the mine will be through a service shaft, development shaft, and a conveyor decline. The shafts are being sunk under contract and the conveyor decline is being driven by Molycorp. The driving of the decline began in February, 1979 with a 10-man mining class. By the first of May, enough men had been trained to begin a continuous operation and by March 1, 1980 the face had reached the 1500 m mark. The heading is being driven with trackless rubber-tired equipment using a three-boom drill jumbo, 2.7 m3 LHD units and 7.3 m3 trucks. Ground support has been by rock bolts and wire mesh, followed by Fibercrete. A 16.5-kt/d underground molybdenum mine is being developed at Questa in northern New Mexico by Molycorp, Inc., a wholly-owned subsidiary of Union Oil Company of California. The new $200-million underground project will revitalize mining and milling activity at Questa, where small scale underground mining first began in 1920. Large scale open-pit mining was initiated in 1965 but now, because of the high stripping ratio, surface mining is being phased out. Construction of the underground mine began in 1979, and first production is scheduled for early 1983. The company expects full capacity - 9 Gg of molybdenum per year - to be reached in 1984.

Jan 1, 1980

The role of ZnSO4 in activation of sphalerite (ZnS) and deactivation of lead-activated sphalerite has been investigated. Adsorption of metallic ions at the solid-solution interface, electrokinetic results for sphalerite under different chemical conditions, and thermodynamic calculations were used to elucidate the mechanisms involved. It is shown that flotation response of sphalerite in absence of activators is rather weak and that adsorption of ethyl xanthate on the mineral mainly electrostatic in nature. Zinc sulfate is found to activate the mineral but only in a narrow acidic pH range. This is attributed to the increase of zeta potential as well as the possible increase in amount of negatively charged bulk precipitated zinc xanthate. Lead ions activate sphalerite in a wide pH range and the lead activated mineral assumes a flotation behavior similar to that of galena (PbS). However, addition of ZnSO4 depresses the lead-activated sphalerite by replacing lead ions at the mineral/solution interface.

Jan 1, 1999

By S. S. Peng

In this paper, the precise definitions for a number of commonly used subsidence parameters are given. The subsidence parameters have been determined using an integrated approach for 110 subsidence cases collected in the major US coal fields. Attempts have been made to establish empirical formulae for the parameters. The results of this study indicate that some traditionally-held concepts should be changed.

Jan 1, 1995

By S. K. Nandy, K. F. Unrug

The behavior of the immediate shaly roof within a drift mine in eastern Kentucky, operating in the Coalburg seam, was monitored with roof bolt dynamometers. The dynamometers used were capable of providing readings up to a maximum load of 66.72 kN (15,000 lbs), + 0.022 kN (5 lbs). To observe the influence of moisture on the rate and extent of roof deterioration, 57dynamometers were installed on roof bolts anchored in intake and neutral airways. Monitoring was conducted during the period January 1985 through January 1986, in order to cover a full cycle of dry and wet mine conditions associated with seasonal changes. Analysis of the data showed a trend of roof deterioration induced by condensation and eventual penetration of moisture within the immediate roof bedding planes, leading to rapid disintegration of the mine roof.

Jan 1, 1987

By S. O. Yuan, R. L. Grayson

As a followup to a USBM-sponsored research project, the authors utilized the knowledge-base structure and system concepts from a Sun Sparcstation-based worker-scheduling system of the mine-management support system to develop a PC-based application. The new software adopts the nested-window concept to facilitate data collection and modification on personnel, including their availability and work priorities during a shift. The system can optimally allocate manpower on a work shift and can delineate supervisory training responsibilities. The various components of the software, including enhancements made to the original system, are described in detail.

Jan 1, 1998

By M. Rosenshine, R. W. Barbaro

This paper presents a cyclic queueing model that evaluates the productivity of a shovel-truck materials haulage system. For a cyclic queueing problem with exponentially distributed service times, a cyclic queueing model provides exact solutions in a fraction of the time that simulation takes to produce an approximate solution. The model is applied to an example problem, and the results are validated with simulation. Simulation is used to show that the assumption of exponentially distributed service times and steady state are not serious problems. A cyclic queueing model can be used to quickly obtain an accurate assessment of the productivity of a shovel-truck system.

Jan 1, 1988

By Yohan Cha, Eun-soo Hong, Gye-Chun Cho

"Rapid population growth and scarcity of space have led many developed cities to bury supply facilities. In line with this, utility tunnels have been employed in Korea since the 1970s. However, approximately 70% of structures were installed more than 20 years ago, in response to the issue of ageing, tunnel enlargement has been proposed. The aim of this study is to investigate geo-mechanical behavior due to tunnel enlargement. Tunnel enlargement methods have been researched to suggest a optimal method. A finite element analysis is conducted to evaluate ground behavior by the expansion of internal space. Vertical displacement and settlement trough width are investigated according to ground stiffness and different enlargement size. It was determined that displacement is affected by the enlargement size and ground stiffness. Based on the deformation results obtained from the numerical analysis, it is possible to predict ground behavior and stability upon tunnel enlargement. INTRODUCTION Various infrastructures such as electric lines, communication lines, gas pipes, and water pipes are jointly accommodated by utility tunnels. These utility tunnels improve the aesthetics of urban areas and help ensure stable supply. The first utility tunnel in Korea was adopted in 1978 and new tunnels are still being installed with the development of new suburb cities. Nevertheless, about 70% of the utility tunnels were installed over 20 years ago and they are still being used through ongoing repair. Moreover, 90% of utility tunnels were installed before 1995. With aging of the nation’s utility tunnels various problems such as concrete deterioration and scarcity of capacity have arisen. As solution, reconstruction has been considered. Reconstruction can enlarge space and improve the performance by replacing existing structures. For reconstruction, two routes have been proposed: underground excavation and cut and cover. In order to avoid traffic problems caused by road occupation and civil appeals during construction projects, underground excavation is the more attractive option. Tunnel enlargement methods have been classified (Seo et al., 2008; An et al 2013) and major considerations during tunnel enlargement have been outlined (Beak et al., 2007). Enlargement construction cases on road tunnels around the world were introduced (Kim et al., 2012) and the deformation curve during tunnel expansion was proposed to investigate the range of protection that should be offered (Kim et al., 2008; Beak et al., 2011). However, tunnel enlargement technology is limited to road tunnels and railway tunnels. Hence, a study on shallow box tunnel enlargement is required for practical application."

Jan 1, 2016

By R. L. Grayson

Productivity achievements in underground coal mining over the past ten years highlight the improvement of management practices as well as the adoption of new technology. Research findings and results from operational studies characterize the aspects of good management that translate into high productivity. In concert with these findings, the Mine Management Support System (MMSS) is being developed, under co-sponsorship of the U.S. Bureau of Mines and the West Virginia University Energy and Water Research Center, as a knowledge-based system to enhance more efficient management of underground coal mines. Concentrating on capturing the intricate knowledge needed to manage a mine effectively, MMSS will encompass information and rules on work scheduling, desired work practices, regulations impinging on operations and planning, responses to operating problems, and the labor-management work agreement.

Jan 1, 1990

By H. A. Kortmann

For the commercial production of iron ore pellets from hematite ores, as it is practiced in various pellet plants, the addition of lime has shown to be an efficient means with a view to improving cold compression and abrasive strength of the indurated pellets considerably. Unfortunately, it has also been shown at the same time, that the metallurgical properties as, for instance, swelling behavior, softening during reduction under load and disintegration of the grain, can be adversely affected to a high degree. In the course of smelting tests carried out by renowned steelworks, blast furnace operation was heavily disturbed by the swelling and early softening of the pellets, also by their disintegration in the low-temperature range, which altogether led to a considerable lowering of the smelting rate (1, 2, 3).

Jan 1, 1972

By George Schmitt, Ted Dowey, Grant Millener, Sean McAndrew, Eric Jordan

The Rondout-West Branch Bypass Tunnel is being built to bypass a substantial leak in New York City’s primary water supply tunnel. The 13,500 foot long tunnel travels 600 feet under the Hudson River through the same troubled geology and high pressure water inflows that the original tunnel did in the 1940s. A Robbins TBM traversed this geology and built gasketed segments. Nine thousand two hundred feet of 16 foot diameter interliner was installed and backfilled within the segments. Finally, reinforced cast in place lining was placed. This paper addresses the challenges and the multi-tasking approach the contractor utilized.

Jun 13, 2021

By D. D. Misra

The paper presents a computer simulation package developed for the size¬-reduction circuits of Indian hematitic iron ores. The package is developed by linking independent procedures describing different unit operations like crushing, screening, recycling, etc. Mathematical models are used to quantify the unit operations involved. The models are selected after thorough analytical studies of the samples and data collected from four operating plants. The package developed gives a fairly accurate result with respect to, size and chemical composition of the flow stream and products. The program written in PASCAL can be used to try the flowsheet with various raw ores, as well as different flowsheets with the same raw ore.

Jan 1, 1989

By A. E. Petersen

The United States Bureau of Mines conducted research on high-intensity magnetic separation methods for upgrading tantalum concentrates from Alabama. Process flow sheets were studied to maximize tin removal and minimize tantalum loss. Using laboratory-scale equipment, concentrates were produced which contained over 65% combined Ta2O5-Nb2O5. Up to 78% of the tin was recovered as a byproduct, containing about 70% SnO2. Only 1 to 5% of the tantalum reported with the tin byproduct. The producer subsequently incorporated high-intensity magnetic separation into its process flow sheet to provide concentrates for the National Defense Stockpile.

Jan 1, 1993

By D. R. Spears

The Bureau of Mines has investigated the fundamental aspects of shear-flocculation using a rapid, in-situ particle size analyzer. Silica was stirred in the presence of an aliphatic amine to determine the effects of collector coverage, stirring speed, and solids concentration on the kinetics of shear-flocculation. The results showed that shear-flocculation is a two-stage process. In the first stage, mean particle size increased rapidly in the first 1-2 min of reaction; in the second stage, an equilibrium was set up between the rate of floc growth and floc decay. Collector dosage affected the position of the equilibrium by altering the number of surface sites for particle-particle attachment. A minimum stirring speed was necessary for shear-flocculation to occur and was dependent on solids concentration and collector dosage. This speed was the minimum necessary for particles to overcome the electrostatic energy barrier which kept conditioned particles dispersed. Larger particles flocculated more rapidly. At very high stirring speeds, large flocs became unstable, resulting in a narrowed particle size distribution in the slurry.

Jan 1, 1993

By Y. J. Wang

The Hardy Cross iterative method is the most popular technique for solving a ventilation network problem with natural air splitting. This method traditionally solves each mesh equation by an approximation during each iteration. Thus, it is interesting from both a theoretical and a computational viewpoint to be able to solve for an exact solution to the mesh equation. Presented in this paper is an algorithm for computing the exact solution to the mesh equation with a variable fan pressure. The algorithm uses signum functions for air quantities to generate an alternative mesh equation in the form of a quadratic equation that has two solutions defined by the well-known quadratic formula. The condition that the derivatives of the alternative and the original equations must be the same provides a basis for the correct choice between the solutions.

Jan 1, 1998

By Y. K. Yen

The most serious problem for on-line coarse particle size measurement from a conveyor belt by image analysis is the overlap phenomenon that occurs between adjacent particles. A methodology is developed and described in this paper to estimate the sieve size distribution from the overlapped projected particle images as might be obtained from a conveyor belt. Two aspects of the overlap problem have been taken into consideration. First, several image processing algorithms were studied to find the most suitable technique to separate the projected overlapped particle images for narrow sized particles. These image segmentation algorithms include two-dimensional thresholding, edge detection and Watershed discrimination techniques. The other aspect of the overlap problem is related to the determination of the general kernel function for the partial particle images obtained from the projection of the overlapped particle bed. In this regard, a computer simulation technique was applied to mimic the overlapped particle bed for narrow sized particles, then the general kernel functions of the partial particle images were determined.

Jan 1, 1994

By D. L. Shenck

The Navajo Mine is exclusively a multiple seam surface coal mine located in the northwest corner of New Mexico, and entirely on the Navajo Indian Reservation (Figure 1). It is owned and operated by the Broken Hill Propriety Co., Ltd. of Melbourne, Australia. The mine began production in January 1963 with a long term fuel supply agreement with the Four Corners Power Plant. The 2175 MW nominal generating capacity of the Four Corners Power Plant consumes 8-8.5 mm tons of coal annually. With estimated reserves totaling 1.1 billion tons of strippable coal, only one third is presently committed to the generating station. As development has continued over the years, mining operations have advanced into more complex geologic areas to satisfy the utilities demand for coal.

Jan 1, 1990

By R. M. Powers

The Florida Institute of Phosphate Research (FIPR) has funded a four-year research project to develop a computer model 'which will predict the hydrologic impacts of phosphate mining on surface and groundwater systems. The core of the model is an analytical geographic information system (SPANS) which integrates EPA's Hydrology Simulation Program Fortran (HSPF) surface water model with the McDonald-Harbaugh groundwater model (MODFLOW). The hydrologic model conducts both event and continuous annual Simulations driven by variable precipitation and temperature data. The model is currently being calibrated and will be ready for distribution to the user community in mid-1991.

Jan 1, 1990

By A. B. Cecala

The Bureau of Mines has been performing research to lower the dust exposure of workers at mineral processing operations for a number of years. This research has mainly been directed at source control techniques in an effort to lower a worker's dust exposure at a particular job function. In some cases, this control technology provided a carryover effect in lowering the exposure of workers at other locations, but for the most part had very little effect in lowering dust levels throughout an entire mill building. Recently, the Bureau became aware of several mineral processing operations having problems with high over-all mill dust levels. These operations were all using baghouse-type collectors to address their most serious dust contamination areas. Although these major dust sources were being controlled, there were numerous minor dust sources that were not. These minor dust sources were causing dust levels in these operations to gradually increase as the day or shift progressed. The intent of this work was to determine general guidelines and design criteria for operations that may be interested in implementing a total mill ventilation system. Most mill buildings can be considered a closed system and thus any dust that is not being controlled within the structure, will cause dust levels to gradually increase over the shift. A total mill ventilation system should be designed to draw clean make-up air in near the base of the mill. This air provides general purging and may clear some dust laden areas throughout the mill structure. This air should be discharged at or near the top of the structure, where it is not a contaminant to plant personnel working outside. Without this exhaust system, dust can exit the building through open doors, windows, etc., and contaminate outside plant workers. This dust can also be recirculated back into the mill building causing additional contamination problems. A total mill ventilation system is not a stand-alone technique, but is a supplemental technique to assist other localized dust control systems.

Jan 1, 1994

By Fredrick C. Kruger

We can confidently predict such obvious long-term trends affecting the minerals industry as - increasing consumption, exhaustion of easily discovered near-surface ores, and sharp limitations upon open pit mining by environmental considerations. There- fore, we must intensify the exploration for, and the development and exploitation of, deep bodies of potash and other ores. This paper examines the state of the art of the search for, and the evaluation of, potash from both a geological bias and a mining practicability. The use of indirect geological methods and geophysical techniques, followed by expensive deep drilling, are the conventional approach to evaluation and development of mining plans. The geologist and the geophysicist will have to find ways to perform both of these tasks better and cheaper.

Jan 1, 1973

By Ivan V. Klumpar

If components of a gas-liquid stream react with each other and with stationary solids, involving parallel and sequential, reversible and irreversible, and slow and instantaneous reactions, the process can be defined by a set of simultaneous differential rate equations and simulated as multistage semibatch re¬actors. Each stage is divided into finite time increments. Within each increment, even the simultaneous reactions are treated as sequential. The proposed method follows process evolution from non-steady state startup to normal operating conditions. It allows computing byproduct buildup in recycles, tracer response curves and, in case of underground processes, expansion to adjacent parts of the deposit.

Jan 1, 1979