Search Documents

By J. J. Harrington

The pH control system at Kennecott Copper Corporation's Nevada Mines Division concentrator consists of two independent systems, lime dilution and lime addition. Lime dilution is accomplished in a mixing tank where slaked lime and water are introduced proportionately. The desired dilution of the milk of lime is determined by the electrical inputs provided by eight pH probes, one per grinding section. The inputs are averaged and applied to a time base generator. The summation output of the time base generator determines the proportion of lime and water that are to be mixed and applies this input to a voltage sensitive switching device. The switching device provides a signal to one of two relays which will add either slaked lime or water, dependent upon the summation output. The entire cycle is based on a two-minute repetition rate to allow for sufficient mix time. Responsivity is controlled by maintaining a limited maxi- mum solution level in the mix tank. Lime addition is controlled independently within each grinding section. The electrical input from the pH probe in a given section controls the solenoid valves which provide lime to each of the ball mills. The valves remain open within a time range capable of maintaining the pH of flotation feed at a given set point.

Jan 1, 1975

By R. R. Dorfler

The existing regrind circuit at the Climax Operations uses sodium cyanide and Nokes reagent to reject pyrite, copper, and lead minerals. Laboratory flotation studies were performed using feed to flotation following first-stage regrinding. The effects of conditioning time, pH, and the concentration of depressants such as Nokes reagent and sodium cyanide on the rejection of pyrite, lead, and copper minerals were investigated. The metallurgical results indicate that, in the presence of depressants, the rejection of copper is strongly dependent on the pH. Preliminary mill testing confirmed the finding. The rejection of impurities is also dependent on conditioning time. The recovery of molybdenite is independent of the variables investigated.

Jan 1, 1981

By M. Spangler

FirstMiss Gold installed a supervisory control system based on Pavilion Technology's Process Insights neural network software and Oil System's PI data historian. The primary goal of the system was to control the acid preconditioning circuit. However, our first successful control loop was on the limestone feed rate to the neutralization circuit. The information gained by modeling these circuits and the better control provided by the system has resulted in reagent savings of over $80,000 per month.

Jan 1, 1995

By Terry O. Arney

Ore Reserve Models are well established evaluation and mine planning tools. BY definition, these models are made up of regularly sized blocks, arranged in a three dimensional matrix. Two dimensions correspond to north and east directions, and the third, to the depth or elevation. The dimensions of the blocks need not be equal, but generally at least two of the dimensions are equal. The blocks are located in space by coordinates which are generally translated into index values for computer applications. Each block will have quantitative attributes, such as grades, densities, rock characteristics, etc. assigned to it. The process of assigning values to each block in the three dimensional matrix is the process of ore reserve model development. One of several interpolation procedures may be employed to predict the value of a block, based on surrounding data. Block value models have several uses. The utilization of block models in ore reserve computations is quite common. Here, ore reserves may be calculated by level or by cross-section for the entire deposit. For each ore reserve calculation, multiple cut-off grades may be analyzed to determine the ore reserves under different cut-off conditions. The other major use of block value models is in mine simulation. Through simulation, profitable studies that analyze the effect of alternate ore removal sequences can be undertaken to determine economic optimality. Other studies that are undertaken in mine simulation problems include the evaluation of mine layout, pit slope effects, and the impact of varying cut-off grades.

Jan 1, 1974

By Ross W. Whipple

Applying geophysical techniques in potential geothermal areas has received: little attention in the United States, though it is widely used and accepted in New Zealand and Italy. In those countries it has been demonstrated that geophysical surveys can be useful in locating new geothermal areas and in directing test drilling programs. Geophysical studies in a thermal region can provide structural information and, if conditions are right directly; locate subsurface hot waters. They can give indications of sub-alluvial rock types and of the thickness of alluvial cover. In certain cases they can be used to estimate the power potential of a hydrothermal system.

Jan 1, 1963

By P. Brumit, L. Grady, R. Mitts, V. Holm

The Mesquite mine is a large, open pit, heap leach gold mine owned and operated by Gold Fields Operating Co.-Mesquite. The mine uses a fully integrated mine planning and reserve modeling software system developed at the mine. This system has recently been extended to include short-term mine planning, grade control, and daily production reporting. The grade control portion of the program uses a multiple indicator kriging (MIK) approach using the blast-hole spacing and exploration assays. The program permits ore control geologists and mine planning engineers to have immediate access to all the information.

Jan 1, 1991

By D. Veigel, J. D. McKay

Model enhanced Expert control has been implemented at the Newmont Lone Tree mill grinding plant as well as rule based Expert control for flotation and thickening circuits. The project has been successful in producing benefits but more importantly has contributed to an ongoing effort for continuous process improvement. This paper discusses how the control at Lone Tree has evolved and the part that Expert control has played in the overall improvements made. Specific examples of how the advanced control has integrated with instrumentation and stabilizing control are given and illustrations of how it has been effective in defining limitations and bottlenecks in the process or process control areas are provided.

Jan 1, 2002

By John E. Young

United States Steel Corporation's Winifrede Mine is operated by Lynch District in the mountainous region of Eastern Kentucky. This region is characterized by narrow mountain ridges and precipitous slows which present both an opportunity and challenge in the design and selection of coal handling facilities for the movement of coal from the section belts to the railroad cars. The narrow finger ridges precluded use of underground haulage and, thereby, presented the opportunity to use high capacity equipment on the outside bench. The precipitous mountain slopes, steepest at the Winifrede seam horizon, presented a challenge to select a solution for lowering the coal approximately 1000 feet from the seam level to the valley floor railroad load-out point. It was evident from the start of planning that these two factors predominated; namely, rail haulage and coal lowering, and solutions to these would determine the final design of the Winifrede Mine coal handling facilities.

Jan 1, 1970

By J. O. Guthrie

Newmont has delineated a 600,000+ ounce gold reserve in the Cargo Muchacho Mountains. This is a desert range underlain by Proterozoic(?) Tumco Formation (gneiss) intruded by Jurassic granitic plutons, and cut by low angle shears of the late Cretaceous Chocolate Mountain Thrust event. Gold, associated with pyrite, quartz veinlets, and propylitic alteration, is emplaced along low angle shears. The mineralizing system, enriched in tungsten, copper, zinc and arsenic, was active during Eocene time. Gold reserves are found in eleven areas as moderate to high tenor deposits that may be mined by open pit and underground techniques. Eastmaque Gold Mines Ltd. is developing the deposit.

Jan 1, 1987

By P. Somasundaran

The use of chemical additives in ultrafine grinding will be reviewed in this paper for the case of grinding of quartz in solutions of surfactants and inorganic electrolytes including some dispersants under different conditions of pH and ionic strength. Mechanisms are examined by correlating the grinding effects with those obtained for the influence of these chemicals on zeta potential, pulp fluidity and flocculation/dispersion characteristics. The analysis suggests grinding depends mainly on the state of aggregation of the ground products in- side the mill and the pulp fluidity. Implications of the observed effects on ultrafine grinding in general are discussed.

Jan 1, 1983

By Gregory E. Klosterman

American Aggregates Corporation is one of the leading producers of mineral aggregates in the nation. Production is from deposits of glacial sand and gravel and limestone and dolomite bedrock. Annual production from 33 plants is 25,000,000 tons. Land consumption is at the rate of 300 to 400 acres annually. This annual rate of consumption presents a continuing challenge to the exploration and mining personnel to meet the requirements of reserve replacement, mining and land rehabilitation.

Jan 1, 1974

By M. M. Rajkovich

Just prior to the close of the century, the Mine Safety and Health Review Commission issued its long-awaited decision in Berwind Natural Resources et al. vs. Secretary of Labor[1] to usher in the new millennium. The case arose as a result of a mine explosion in Eastern Kentucky resulting in the US Mine Safety and Health Administration's (MSHA) issuance of 225 citations, not only to the contractor but to four affiliated entities of Berwind Corp. While an Administrative Law Judge dismissed citations to three of the four Berwind entities, MSHA and the remaining Berwind entity appealed the case to the commission. Although the commission effectively left intact the administrative law judge's decision, it announced a new theory of liability that would apparently be applied in the future, namely the unitary operator theory.

Jan 1, 2003

By Arnold E. Lamm

The degree of economic, progress of a nation is measured by its possession and use of energy, sources. The future of coal in the West hinges on its ability to participate and grow in the energy market. A source of energy is, in the long run, only as good as the ability of the industry to develop its reserves economically. The economic development of the tremendous coal reserves, literally hundreds of billions of tons of coal in the States of Colorado, Utah, Wyoming, Montana, New Mexico, and Arizona, poses a very real question in the light of the known mining technology of our day. Basically in America today, coal is mined from the earth either by the strip mine or underground mine method; in the West, the large long-term, contracts now in force with utilities are mostly from coal mines utilizing the strip mine method. However, the preponderance of the known coal reserves of the West are located deep underground and will have to be mined by the various; underground mining processes. The problems encountered in the West with regard to underground mining vary from state to state but, on the whole, do not present what might be considered a miner's bonanza. I do not mean to' infer that the underground coal of the West is unmineable, but I do want to emphasize that the tremendous reserve figures do not present a true picture in the light of present day technology.

Jan 1, 1965

By Robert Stefanko

The importance of underground stress instrumentation cannot be minimized. It was Lord Kelvin who said that unless you can assign a number to a quantity,, you know very little about it. Most engineers will agree although this kind of statement is resented by our friends in non-technical fields. Mining is undergoing a revolution from art to science. But how can mining methods be optimized if there is no way of measuring the effectiveness of a given mining method? Do we know how effective a' support is unless we can determine its reaction to the mine structure? How do we assess the need for modifications to existing systems and supports, and how do we measure the effectiveness of such changes? Cut and try techniques are too wasteful of time and energy, and rarely provide solutions to a given problem. The purpose of underground stress instrumentation is to provide answers to some of the above questions -- answers that cannot be obtained otherwise This does not mean that laboratory studies are not valuable -on the contrary. Laboratory and underground studies supplement one another. Rock mechanics had its conception with the study of stresses in homogeneous, isotropic, and elastic models subjected to various force systems. These analyses were valuable inasmuch as they pinpointed possible sources of trouble due to stress concentrations. If the results observed underground did not always agree with the experimental analysis, it was not an indictment of the latter. More probably, the discrepancy could be attributed to the lack of similitude between model and prototype. The more nearly one can simulate underground conditions in a model, the more apt one is to produce results which correlate well-with underground observations. It is impossible to completely simulate underground conditions because all of the significant design parameters have not been recognized and evaluated. What better way can one evaluate these parameters than by underground stress instrumentation?

Jan 1, 1963

Silver bearing bulk sulfide concentrates from several Peruvian mines were autoclaved in a 19 liter (five gallon) laboratory autoclave in Lima, Peru. Cyanidation of autoclaved concentrates following a hot lime jarosite destruction step extracted over 98 percent of the silver and over 95 percent of the gold. Autoclave operating parameters such as time, temperature, pulp density and autoclaved solids recycle were investigated and reaction rates determined. The problems of excessive heat generation, silver solubility during autoclaving, and formation of pellets containing unreacted sulfides were addressed. The data presented will be used to design a continuous autoclave pilot plant to pro-vide reliable scale up data for a 50 -100 ton per day facility.

Jan 1, 1992

By R. C. Ford, J. Kelsey, S. A. Pierce, M. D. Ankeny

Evaluation of acid drainage risk from spent (leached) ore in arid climatic zones consists of two components: (1) whether residual and secondary minerals will release acid and metals when exposed to rainfall, and (2) whether ambient rainfall is likely to infiltrate, and eventually impact surface or ground water resources. The risk of acid drainage from spent ore at the El Abra on-off copper leach pad operation was evaluated using conventional geochemical methods and unsaturated flow models. Although geochemical testing indicated poor quality water would result from any seepage, unsaturated flow modeling demonstrated that infiltration and seepage were unlikely given the arid climatic conditions. Modeling further demonstrated that the residual moisture content of the spent ore when it is removed from the leach pad controls the risk of seepage. To further reduce the risk of seepage, operational controls were developed and implemented at the El Abra site.

Jan 1, 2000

By R. Larry Grayson

A survey of 1250 surface and underground coal mines across the United States was made according to a stratified sampling technique based on national coal districts. A total of 171 responses (13.7% response rate) have been returned and summarized, giving a picture of computer usage in the coal industry. Overall, 63.5% of the respondents use computers, but the percent varied from 100% for large mines to only 44.1% for small mines. As expected, a proliferation of microcomputers has pervaded the industry. Importantly, in spite of the high usage of computers in the industry, sophisticated engineering applications have not yet burgeoned.

Jan 1, 1989

By F. Sill

The disposal of residual material from processing and combustion of coal, from incineration of domestic refuse and sewage sludges kind to the environment is a prior task for the future. Deutsche Montan Technologie (DMT) has developed a new technique which makes possible to fill-up goaf cavities behind running caving systems in coalmining. In a mixing and pumping station on the surface high concentrated suspensions are produced from the above mentioned materials. The paste is pumped through pipes to the coalfaces and via trailing discharge pipes stretched to the fracture zone in the caved-in goaf. Since three years a special designed plant is working successfully on a coal mine of Ruhrkohie AG.

Jan 1, 1994

By B. R. Waples

Sometimes a project is born easy, sometimes a project has a hard time being born. Probably every project can say we had tremendous problems to overcome and they would all be right. This project had all things happen to it. Born easy, a hard time after being born, there were tremendous problems to overcome but here it is, a major copper project, a major operation, and a new source of copper for Mexico and the world market. La caridad is an ore body located in the state of Sonora in northwestern Mexico. It is at an elevation of 1,200 meters above sea level and the nearest major city is Hermosillo, the capital city of Sonora. Hermosillo is located approximately 270 kms (about 168 miles) to the southwest of la caridad. North of la caridad, 130 kms (about 81 miles), is the U.S. border town of Douglas, Arizona, which has a sister city on the Mexican side of the border -Agua Prieta.

Jan 1, 1979

By B. K. Parekh

Silicon carbide (SiC) can be produced by heating rice hulls to elevated temperature, The product is a mixture of beta crystalline silicon carbide whiskers, particles and unreacted carbon. The silicon carbide whiskers are 0.5 micron in diameter and 50 to 100 micron in length and have been found useful for reinforcing metal and other composite materials. The carbon can be removed by combustion, but this makes separation of the silicon carbide whiskers from particles difficult and a high grade whisker product cannot be made. However, a clean high grade Sic whiskers product can be obtained from the pre-burned converted rice hulls using physical separation processes that are based on differential wetting. Recovery of Sic whiskers from the pre-burned material was found to exceed 90 percent. A modification of the froth flotation process developed during this study is now being used commercially to separate silicon carbide whiskers and particles and to recover a high grade whisker product.

Jan 1, 1985