Search Documents

By Thomas W. Turk

The water treatment industry has historically been involved with reducing or inhibiting the inherant scale forming or fouling tendencies of natural waters associated with large industrial cooling water systems. Fouling is an extremely complex phenomenon. From a fundamental point of view, it may be characterized as a combined momentum, heat, and mass transfer problem. Chemical reaction kinetics is involved, as well as the solubility characteristics of salts in water and corrosion technology. It is a routine practice to over size pumps, piping and heat exchangers to compensate for fouling.

Jan 1, 1983

By D. Yadon, P. Lee, W. Kelly, C. Stilwell

Rico is a small town in an old zinc mining district in a mountain valley of southeastern Colorado. Mine waste rock and mill “tailings” remained after over 100 years of mining in the area, leaving associated surface water and groundwater impacts. Atlantic Richfield Company is proposing an innovative approach, which uses lime precipitation and wetland ponds (semi-natural system, also called treatment lagoon in a wetland setting) to treat adit water in the Rico area. Besides using a non-conventional treatment approach, a non-conventional (non-Superfund) regulatory/administrative approach is being proposed. This paper will focus on the water treatment issues and solutions, as well as describing the innovative “watershed” regulatory process.

Jan 1, 2004

By Zhang You-di

A comprehensive model has been set up for surface mine long range planning. It is a system simulation model based on the oriented graph theory. Via this model, a series of mining results such as mineral and waste volume, mineral quality, mining intensity, material haulage distances, dumping area parameters and mining coat for different mining alternatives, can be derived and optimized. This model has been applied to 37 mining alternatives in several surface coal mines and proved mathematically correct and results reliable.

Jan 1, 1986

By P. Riveros, A. Pratt, G. Deschênes

The effect of pyrite, pyrrhotite, chalcopyrite, realgar and arsenopyrite on gold dissolution in cyanide media was investigated. The cyanidation of synthetic gold ores, in the presence of various concentrations of sulphides, was studied under constant experimental conditions. A mineralogical analysis of the minerals was performed. The leaching kinetics were determined. The negative effect of sulphides on the gold dissolution rate varies with the sulphide mineral, and decreases according to the following order: realgar > pyrrhotite > chalcopyrite > pyrite > arsenopyrite. The chemical characterization of gold and sulphide minerals surfaces using X-ray photoelectron spectroscopy (XPS) was undertaken to identify the mechanisms involved. XPS analysis showed that a passivation layer of sulphides, arsenic or iron compounds may form on the gold surface as a result of the dissolution of the sulphide minerals.

Jan 1, 2002

By R. E. Hucko

The goal of the U.S. Department of Energy (DOE) coal preparation R&D program is to develop technology to reduce the ash and sulfur contents of United States coals to levels such that the resultant product can be formulated into a high- quality solid or slurry fuel that could replace oil or natural gas in both new and retrofit applications. The Coal Preparation program is implemented by the Pittsburgh Energy Technology Center (PETC) and is conducted both in-house and by a cross section of industrial organizations, universities, and national laboratories.

Jan 1, 1986

By Howard N. Egan

EASTERN COAL CORPORATION is located in the heart of the Appalachian Mountain area of extreme Eastern Kentucky, The mountains are of sedimentary origin, and have been deeply eroded by streams as the area has been thrust up during geologic time. There are many seams of coal interspersed between beds of shale and sandstone. While some of the seams are thin, there are a number that can be economically mined. We are mining the Pond Creek, or No. 2 Gas Seam, at a rate in excess of 6,000 tons per day. Our central preparation plant utilizes tromp baths for the plus 3/8" size and Rheolaveur for the minus 3/8" portion. No provision was made to recover the fine coal, which was included with the plant effluent pumped to a 12 acre refuse pond. The pond is impounded behind the coarse refuse dump. This pond rose 15 feet last year. Obviously, no pond could stand many years at this rate. Limited pond space in this rugged area of steep hills and narrow valleys dictated a revised disposal method. Our first thought was that it would be necessary to dry the fine refuse sufficiently to permit inclusion with the coarse refuse, which is hauled uphill by monitor and then trucked to final disposal.

Jan 1, 1967

By Allan M. Johnson

Dewatering is a major operational cost at sane mines. Under certain conditions, costs associated with water disposal may continue beyond the productive life of the mine. For mines with mineralized waters, this is of special concern. Since 1974 experience has been gained from the examination of a number of closed underground metal mines that exhibited drainage problems. It was observed in certain cases, that had appropriate steps been taken prior to closure, that the resulting drainage problems could have been largely avoided. The pre-closure steps would have involved alteration to the "plumbing system" of the mines: i.e., the drifts and crosscuts interconnecting the workings of the mine. This could have best been accomplished by the placement of bulkheads and/or selective drifting. In addition to reconfirming that hindsight is 20-20, a lesson learned from these case studies shows that a relatively simple hydrologic evaluation prior to mine closure may avoid a troublesome and costly drainage problem.

Jan 1, 1983

By Robert D. Gibson, E. Donald McKay, Paul B. DuMontelle

Subsidence of the land surface in some parts of Illinois is caused by underground coal mining. The U.S. Bureau of Mines is backfilling abandoned mines at selected sites in southwestern Illinois in an attempt to support failing mine openings. The Illinois State Geological Survey assists the Bureau by developing geologic and engineering information. As part of this investigation, television probes of fifteen injection borings in Belleville augmented conventional methods of study. The television probes of uncased sections of borings revealed several phenomena. Water erosion caused shale beds to slough, which partially filled some borings. Fractures caused by subsidence were identified, and excellent views of underground mine workings provided documentation of the mining method. The condition of mine timber was evaluated. Pack walls supported some openings. Both floor heave and roof fall were observed to be causes of failure in the mines.

Jan 1, 1982

By Ned M. Smith

The Mississippian Salem Limestone, from which dimension stone is quarried in Indiana, is principally a calcarenitic rock formed of fossil bryozoans, echinoderms, and specimens of Endothyra. Numerical associations of the fossils, binding materials, oölitically coated fossils, and voids were determined by counting points on the surfaces of 278 thin sections of the limestone. Median sizes, coefficients of sorting, and skewness numbers were computed from measurements made of constituents in these thin sections. Many other samples and numerous exposures of the Salem and contiguous parts of adjacent formations also were studied. The organisms that furnished the skeletal material for formation of the Salem Limestone were chiefly gregarious and communal. Salem rocks are formed of nearly whole skeletons, of dismembered or slightly damaged skeletons, and of skeletons thoroughly ground up, because currents in the Salem sea varied in their ability to move and damage these materials. Locally the sediments are of uniform grain size because of sorting by currents and because related organisms grew to similar sizes. Rocks of the formation contain different proportions of the fauna both because the animals lived in these proportions and because their skeletons were mixed together by currents. The proportional relationships between members of the fauna were constant locally and for short periods of time. Study and mapping of the faunal associations, numbers of oölitically coated fossils, bedding structures, and size parameters enables geologists to suggest sedimentologic histories and sequences in areas of various sizes. Interpretations based upon such areal studies are necessary for evaluation of the dimension-stone potential within the Salem Limestone.

Jan 1, 1966

By D. A. Saint Don, M. Prueher, S. Barnwell

With the current changes in technology, multiple methods are now available for aggregate resource identification. From Sonic to Coring, Reverse Circulation to Percussive, there are many choices to make regarding drilling technology. The discussion will outline the methods above with focus on aggregate investigation and highlight the new technologies that will make a difference in your search.

Jan 1, 2004

By J. Hanna

The University of Alabama Mineral Resources Institute (MRI) has developed a unique process for selective fatty acid flotation of carbonate gangue from sedimentary apatites (francolite) in the pH range of 4-6 without collector conditioning of the pulp. The process, which does not require an apatite depressant, was modified to benepciate a high- MgO siliceous phosphate matrix from south Florida. The modified process includes two flotation stages, one for car- bonate removal and the other for phosphate recovery from the siliceous gangue. The selective flotation separation of the carbonate and phosphate from siliceous constituents of the matrix at various pH levels and collector dosages are discussed. In the carbonate flotation stage, about 70% of the MgO was rejected in the froth. The phosphate flotation stage produced concentrates analyzing about 31% P2O5 0.7% ? 5 MgO, and 4% insol. The overall P2O5 recovery In the two stages was about 85%

Jan 1, 1991

By Mostafa Benzaazoua, Bruno Bussière, Mukendi Kongolo

The desulphurization process has been proposed over the last few years for acid mine drainage control at certain mines, which generate low to medium grade sulphidic tailings (-3 to +25 wt% S). The environmental sulphur recovery, which means the sulphur to be floated to produce a non-acid generating final tailings, depends mainly on the intrinsic neutralizing potential of the tailings. However, in some cases the sulphur cleaning is complicated by other parameters which affect the flotation probability of the sulphide particles. In this study, a number of tests were conducted with a Hallimond tube and Denver Cell on both pure mineral and mine tailings. To develop a better understanding of the mechanisms of non-selective sulphide flotation, three types of approach were investigated in this work: (i) pure pyrite at progressive milling degrees, (ii) artificial mix of pyrite and quartz at different calibrated granulometry and (iii) same composition tailings with 26 % wt sulphur at progressive milling degrees. The effect of the granulometry on the sulphide flotation was demonstrated both. The results allow us to define a granulometry model, which can then be considered in the whole desulphurization modeling.

Jan 1, 2000

By Carl Hansen

Sonora Mining Corporation (SMC) operates the 6,000 tonne per day Jamestown open pit gold mine in the Mother Lode district of California. The mine has been in operation since January, 1987, and has produced approximately 7,800 kilograms of gold since start-up. The property consists of five ore bodies lying along a five kilometer stretch of the famous Mother Lode vein system. At present, only the Harvard ore body is being mined. The Harvard pit is centered around a historic underground mine of the same name that was operated from 1896 to 1916. The present ore body averages 2.5 grams gold per tonne as free milling gold and auriferous pyrite. The project consists of the open pit mine and concentrator complex in Tuolumne County, California, and a carbon-in-pulp leach plant located near Yerington, Nevada.

Jan 1, 1990

By Johannes Jäger

"A composite shell lining typically consists of an outer permanent sprayed concrete shell, a water proofing layer and an inner sprayed or cast concrete shell. Composite shell linings become more and more popular and have been built recently on large scale infrastructure projects. Surprisingly there is very little published literature on the actual structural design of composite linings. As a consequence there is a lack of common understanding on how to design a composite lining structure. Composite action of the outer shell (primary lining) initially carrying short term ground loads and the “unloaded” inner shell (secondary lining) require nonlinear concrete modelling to be able to assess the bearing capacity of the composite lining structure adequately. The composite action of the waterproofing membrane and the inner and outer shells can be considered either by simplified closed form solutions or by numerical models. Strength and stiffness parameters of membrane and concrete govern interaction of inner and outer shell. This paper should contribute to understanding composite lining behaviour with focus on the bearing capacity at limit state by taking into account the actual loading history. Possible ways and concepts on how to deal with these topics are presented, however a broader discussion on limit states of the composite lining materials – also in the long term will be required to come to an agreement on composite lining design methodology. INTRODUCTION Composite Lining Technology Traditionally the construction of shotcrete lined tunnels incorporates primary and secondary linings, separated by a sheet or a sprayable waterproofing membrane. The primary lining shotcrete is considered to be structurally temporary and the secondary lining to be permanent, leading to designs which ignore the bearing capacity of the primary lining in permanent condition. There was general perception that the shotcrete lining installed immediately at the tunnel face, experiencing strains up to 1% and even cracking in the early age, combined with mesh reinforcement additional support measures like lattice girder, spiles and bolts cannot be considered as a permanent structure. But also former shotcrete mixes showed significant weakness with respect to durability suggesting a more temporary nature of primary lining shotcrete. On the other hand it was clear that primary lining shotcrete does not disappear, it may lose probably a certain percentage of its bearing capacity, but discounting any contribution from the primary lining at all was considered inherently conservative. There were different strategies to account for the risk of reduced durability and bearing capacity of the primary lining, either by selecting moderate ground loads for the secondary lining design, by assuming that some residual load will be carried by the primary lining. This approach is very much based on experience. Another more rational possibility is to assume that the primary lining degrades into a rocklike material, which is weaker than the primary lining shotcrete but still imparts some strength to the ground around the secondary lining, but does not need to comply with any concrete design codes any more."

Jan 1, 2016

By Roger E. Melley

Since startup of the Syncrude Canada Ltd. (SCL) oil sands facility in northern Alberta 15 years ago, numerous improvements have been made in the ore conveying system and equipment. The unique nature of the material conveyed coupled with the wide range of environmental conditions encountered results in a number of unparalleled challenges. Most of the improvements have been brought about through the use of detailed field evaluation. Numerous publications are available that detail the various aspects of conveyor technology, and a significant list of papers are presented each year adding to the knowledge in this field. In the area of power formulae in the mid- 1970s, there were two major sources for use in the design of the SCL conveyors: the Conveyor Equipment Manufactures Association Handbook, 1988, and DIN Specifications 22101: Belt Conveyors for Bulk Materials, 1982. These sources were supplemented by the knowledge of the belt and conveyor equipment vendors and from the general literature. The SCL design was based on the CEMA formula. However, it was accepted that this empirical approach had been developed for use with more conventional materials in more reasonable climates. To accommodate

Jan 1, 1993

By Richard Gallagher, Russell K. McFarland

INTRODUCTION The Southern California Rapid Transit District has commenced Preliminary Engineering for an 18 mile Metro Rail Project. This initial line will consist of approximate 36 miles of single track tunnel and 16 subsurface stations. The estimated cost of $1.2 Billion in 1978 dollars, places it in the category of a major public works project. During the planning phase of this project, particular attention was paid to the National Academy of Science Reports, "Better Contracting for Underground Construction" (1974), "Better Management of Major Underground Construction Projects" (1978), and "Management of Urban Construction Programs" (1980). The improved transportation service that this project will furnish the Los Angeles Metropolitan Area will result in significant benefits that will add immensely to the economic well being of the community-which is one of Webster's definitions of improved productivity. RAPID TRANSIT PROJECT BACKGROUND Rapid Transit studies have been going c in the. Las Angeles area since 1925. In 1969 and 1974, sales tax ballot issues were not adopted by the electorate of the county mainly because the pre-ponderous of County voters are outside the City of Los Angeles.

Jan 1, 1981

By Leonidio Stegmiller

Since the petroleum crisis in 1973, charcoal1 is being considered one of the most important fuel for the Brazilian consumers, mainly for pellet's producers. In replacing fuel by charcoal mixed up with ore, obviously one of the first thing to be investigated is its influence in the product's quality. Special attention has been given to the metallurgical characteristics. This paper infocus the effect of increasing dosings of charcoal to the pellet's porosity and how other physical and metallurgical characteristics will be affected accordingly. This work was carried out using two different finesses of charcoal and dosing varied from 0.5 to 2.0%.

Jan 1, 1982

By C. E. Capes

The continuous balling? operation whereby a moist particulate mass is tumbled in a horizontal revolving drum with recirculation of the undersize product can be extremely unstable. Product and recycle rates are subject to wide fluctuations. Although the problem seems to be well-recognized, there is little published information or quantitative data readily available, especially in relation to industrial-scale circuits. Probably the best available published results are in the Russian literature, an illustration of which is given in Figure 1. These data, taken from a study') of some of the factors which influence the stabilization of the pelletizing process, illustrate the wide variations in circulating load and circuit productivity which may be encountered over a period of operation. The problems of balling circuit stability may be traced to random seed or nuclei generation and uncontrolled agglomerate growth. The situation is analogous to that in crystallization processes where (4 considerable attention is given to nucleation control. Traditionally attempts have been made to optimize system and operating variables to stabilize the balling process. A supplemental approach which is taken here is to build on the considerable

Jan 1, 1975

By J. Fuller, L. Marsden

Windborne dust from alkaline salt flats and mining-related tailings ponds is especially prone to threaten applicable ambient air quality standards. Sodium carbonate crystals, typically present, weather to an exceedingly fine, non-cohesive dust, causing air quality problems for miles downwind. Recently developed specialized polymers react with alkaline dust to form sturdy, wind-resistant crusts with good longevity. An on-going demonstration project at a major trona facility has developed techniques for cost-effective application of these polymers over large areas of soft tailings or sediments in a wide variety of situations. Recently treated areas on the order of 80 acres show effective suppression of dust.

Jan 1, 2004

By F. A. Gates, Bengt Samuelson, James E. Edmunds, S. McCune, Neil Hario, Norman L. Weiss, J. M. Bertram, A. M. Cavaliere, F. M. Jr. Stephens, D. D. Chiang

DESIGN BASIS Size of Project The size of the project generally is expressed in tons of ore milled per day, but company policies differ widely in this respect with a few adhering to this set figure but many expecting the design capacity to be liberal. To some companies that follow the latter practice a 25,000-tpd milling plant that cannot reach 30,000 or 35,000 tpd with¬out major additions is a disappointment. The engineers responsible for planning the operation must know what is intended. Other projects are sized according to the tonnage of product rather than of mine ore; examples are iron ore mills that express size in terms of tons per year of pellets or high-grade concentrates, heavy minerals plants in tons per year of rutile or ilmenite, cement plants in barrels per year, potash in tons per year of muriate, phosphate in tons per year of washer rock and flotation concentrate, and others. However, tons per day milling rate is also the common denominator in most of those instances because the major equipment has to be selected on that criterion. Equally important are operating schedules, particularly the number of operating days per week and shifts per day for ore delivery, crushing, grinding, and processing. Hours per shift also are an impor¬tant factor in design, particularly in the case of ore delivery, and the lost time expected for maintenance, cleanup, inspection, preventive maintenance shutdowns, and many others, has to be taken into ac¬count. Frequently, the ore deposit will vary in hardness and grade to such a degree that the capacity of the mill will vary widely from year to year and cannot be expressed as a fixed figure, but rather as an average over a calculable period, such as ten years, or as a specific daily capacity over the first two years, next four years, etc., or some similar projection. A good example of this kind of situation is Asarco's Mission operation 15 miles southwest of Tucson, Ariz., described by Weiss and Vincent,1 where the major rock types differed widely in hardness, so that a change in the proportion of these types in the mill feed could have imposed difficult design problems if a constant tonnage rate had been expected. Expected Life The life of a mining operation depends upon the size of the deposit and the rate of mining. The latter is a policy decision based on an economic analysis2 which, in turn, is based on many factors. From the point of view of mill planning, the estimated life of the operation determines many criteria and affects many decisions on strength of structures and degree of protection of men and materials, the quality of the materials-handling and process machinery, the type of delivery systems for ore to the mill and concentrates to the smelter or market, environmental considerations, and many others. Costly installations that may be excellent investments for a 20-year project may be waste¬ful for a 5-year operation. An example is the comparison of different methods of crushing or grinding. Take single- vs. multiple-stage grind¬ing-the former may be found more economical for a 5-year operation, and the other, more costly method more economical for a 15- to 20-year life. Mining and Ore Transportation The mining method and the means of transportation of the ore to the first crushing stage have far-reaching effects upon mill design, particularly the crushing sections, and upon site selection (see Chapter 2, Situation of Mill). Consequently, mill design cannot advance until the mine planning has reached at least tentative decisions concerning these important matters, or reach the final stages until much is known about the ore that may be expected month by month and year by year for a reasonable period. Methods of ore transportation used in over 90 underground and open-pit mines are listed briefly in Section 32 (Table 1), and more detail is found later in this section and in Section 10, Storage and Transport. These methods include surface railroad, trucks, conveyors, surface skips, underground skips, and tramming from hoist or tunnel. In surface mining, transportation of the uncrushed ore by rail or truck to the primary crushing plant-conveniently located for lowest overall cost-is most common. Rail transportation provides low perton-mile costs. Truck transportation, though in some cases less eco¬nomical, is more flexible and more adaptable to mountainous terrain; furthermore, recent improvements have reduced the operating costs to keep trucks competitive on low-grade ores. The design of the primary crushing plant will be essentially the same whether delivery is by truck or rail, but the location of the plant is subject to more rigid restrictions in the latter case because of grade limitations, and these in turn may adversely affect the selec¬tion of the mill site as well. The influence of truck haulage in reducing the stripping ratio in open-pit mines is an added reason for predicting a minor role for rail transportation in the future. The use of conveyors to transport ore from the pit to the milling plant involves (in most cases) crushing the ore to a reasonable size (10 to 20 in. maximum with today's crushers) before conveying. The Twin Buttes system3 which went into operation in late 1969, utilizes primary crushers (two) and conveyors to receive rock waste, ore, and low-grade stockpile material from trucks, then transport them to the appropriate destination. Flexibility is dependent upon the porta¬bility of the primary crushers. In the face of this development, inclined skip hoists are no longer important to the mill designers. Underground mines generally pose fewer problems of design; these will be discussed in Chapter 2. Character of Deposit The degree of homogeneity of the ore in various parts of the mine is an important factor. The characteristics that concern the millman (approximately in order of importance) are: hardness, assay, metallurgical response, size distribution,4 and moisture content. Under metallurgical response may be included degree of oxidation, mineral¬ogy, clay content, and reagent consumption, as well as process re¬sponse in general. Short-term variations-hour-to-hour, day-to-day, or even week-to-week-make operation of the plant more difficult, require greater flexibility of process design and, perhaps, also require more instrumentation and manpower. Uniformity of the ore in the characteristics noted previously and

Jan 1, 1985