Search Documents

By M. D. Flavel

Testing methods are described to help in decisions of selecting the most viable comminution circuits. The authors present a comparison evaluation based on numerous studies to help make initial choices for feasibility evaluations. An update summary of completed Bond grindability and Abrasion Index testwork at Allis-Chalmers Process Research Test Center for all materials is included. "What is the best circuit to comminute primary crusher product to make beneficiation feed?" This frequently asked question has the implication that there is one circuit which is universally the right circuit. The answer has been sought ever since it has been necessary to break rock to liberate entrapped mineral values. With every new contribution to the art and the science of comminution, the scope of the discussions broaden. It is not even possible to define what the abstract term best means.

Jan 1, 1981

By Hamid Maleki

Mine seismicity is influenced by the mechanical properties of both near-seam strata and overburden/underburden and the prudent selection of mining methods and mine layout designs, utilizing sitespecific structural setting of the mines. The importance of adequate data collection, monitoring, and prudent structural designs has long been recognized and utilized in many U.S. operations with adequate engineering resources. In this paper, two case studies of historic seismic events and contributing factors, in deep coal and trona mines with overburden thickness exceeding 1,500 ft, are reviewed using observations and analysis. By back analyzing the overburden response in a historic room-and-pillar coal mine, the overburden collapse mechanism associated with a 3.3 magnitude seismic event is reviewed as well as the need for improvements in designs including panel and barrier pillar widths. Similar high-order seismic events were also experienced in trona mines of the Green River Basin during 1990s, interrupting room-and-pillar mining and creating ground control concerns. Efforts to improve structural mine designs are described in this paper leading to stable and productive operations for decades following the high-order seismic events in both coal and trona case studies. These efforts included improving room-and-pillar extraction layouts and utilizing properly designed longwall mining techniques that were verified using long-term geotechnical instrumentation. The study mines are located on the Wasatch Plateau (WP), Utah and in the Green River Basin (GRB), Wyoming. More recently, in Utah’s East Mountain alone, Energy West Mining Company (EWMC) has extracted some 165 million tons of coal without any significant incidents. Overall, favorable geologic conditions and prudent mine layout designs are key elements to this successful experience in both single- and two-seam layouts. Utilization of conservatively designed longwall mining technique in the GRB has been geotechnically stable, using reported experience in 15 panels and monitoring results in the Northwest (NW) District with measurable longwallinduced seismicity being rare. These studies demonstrate a considerable amount of progress that has been made within the last four decades in the application of longwall mining technique, integrated monitoring, and analyses for the verification of structural designs in mines in the United States.

Jul 1, 2023

By Michael M. Maier

The manuscript of this paper was not available for publication when the Proceedings went to press. Should the author elect, he may distribute copies at the time of the Symposium.

Jan 1, 1986

By M. Jaramillo

The expanded west pit of the 15 Mta (13.6 stpy) El Cerrejon mine will eventually reach a maximum depth of 270 m (890 ft). Slope-stability evaluations indicated that this depth, combined with structural complexities, would create a serious risk of footwall instability. Stabilization calls for anchoring the footwall by the installation of 9- to 33-m- (30- to 108 ft-) long multistrand steel cable bolts. For each of the 15-m- (50-ft-) high mining benches, a row of bolts is installed with variable horizontal spacing, depending on the dip magnitude. Cable bolting is now standard operating practice, and an estimated 11,800 bolts will be installed during the life of the mine. Results to date have been satisfactory in terms of the stability condition of the bolted slopes.

Jan 1, 1997

By J. E. Murphy, Y. Topkaya, R. E. Johnson, B. R. Palmer, D. K. Dysinger, R. B. Bhappu, A. E. Clark

The U.S. Bureau of Mines utilized a central composite experimental design to investigate leaching kinetics of pure chalcopyrite in the sulfuric acid-oxygen system. The six factors studied were oxygen pressures of 150, 300 and 450 PSI, leach temperatures of 35O, 65O, and 95O C, oxygen-to-chalcopyrite mass ratios of 0.5, 1.0 and 1.5, leach times of 8, 16 and 24 hours, initial acid strengths of 0.6, 1.2 and 1.8 g H,SO,/g chalcopyrite and pyrite to chalcopyrite mass ratios of 0, 1, and 2. Chemical analysis and oxygen consumption measurements indicatedthat leaching occurs through three consecutive reactions. Temperature was the primary determinant of leach rate and solution acidity was the primary determinant of oxygen consumption, sulfur oxidation, and activation energy.

Jan 1, 1993

By J. C. Rhodes

The demand for good white minerals for many industries including paint and plastics have made it necessary to import high grade industrial minerals from various parts of the world. Some of the calcium carbonate, barite and talc minerals are from China, Mexico, Jamaica and Haiti. These materials can be processed by custom processors. The custom processor can provide a service to the Industrial Mineral owner. The imported materials can arrive in various feed sizes from lumps (3"-6") down to 325 mesh. The materials can also be in various size shipments or container loads. The economics for importing should be investigated thoroughly. The two factors just mentioned can influence the quantity of material to be processed. These two factors can also influence the total cost for each end product.

Jan 1, 1989

By Michael Jatczak, Brett Robinson

The South Bay Ocean Outfall tunnel is located at the U.S./Mexico Border and is one link in a system designed to treat and dispose of raw sewage entering the Tijuana River Valley from Mexico. The 11 finished diameter tunnel extends 19,000’west from the bottom of a 200 deep, 36 diameter drop shaft. At the western terminus of the tunnel, a Riser shaft connects the tunnel to conveyance and diffuser pipes on the seabed. The tunnel runs through the San Diego Formation, consisting of clay, silt, sand, gravels, cobbles, and boulders. A Mitsubishi Earth Pressure Balance (EPB) Tunnel Boring Machine equipped with a large variety of monitoring and control devices was used. This paper will provide an overview of the Project’s construction, with special emphasis on the value of the electronic data acquisition system.

Jan 1, 1999

By Osvaldo A. Bascur, J. P. Kennedy

Companies have installed powerful desktops for their personnel and instrumentation and control systems in their plants. These desktops are, in many cases, connected to a company intranet. Still, process engineers have to obtain their data manually. Engineers use process calculations from manually calculated averages from the plant; field operators collect equipment data on log sheets; and maintenance engineers collect critical information on log sheets. All of this information resides in individual machines. What are the strategic tools that will enable collaboration between them? How can operators, engineers, and managers access plant information to proactively increase their effectiveness in process troubleshooting, plant debottleneclung, aligning with business strategic and customer demand, satisfying environmental and safety regulations, developing capital projects, and implementing control strategies? A nonintrusive environment at the desktop is required to provide the process information to these workers. How can value be added to MS Windows technologies with the legacy systems at a minimum cost? There is no straight answer; however, there is a proven framework to leverage the large investments in new technologies. Objects and components are changing the way everyone relates to their computer and networks. Three examples will be described to demonstrate paradigm change. Today, process engineers can access data at the required level of detail for analysis of critical process variables at their desk or remotely. 1. Process Troubleshooting and Analysis: The engineer can develop an inferential calculation, trigger a process advisor to deter- mine the behavior of the units for the last day, and get the population of a set of batches (heats, blocks, rolls, sheets, etc). 2. Process Control and Optimization: The engineer can connect to a process simulator at steady state or a dynamic simulator of the process to evaluate new control strategies or process unit line-ups and use the process simulator as a process observer for fault diagnosis. 3. Collaboration with Accounting and Maintenance: The engineer can review reconciled data and the process mass balances, suggest maintenance cleaning or recalibration of flowmeters, and evaluate key control performance of all advanced controls.

Jan 1, 1999

By A. G. Royle

Although these exhibit similar structures overall, there are more acute valuation problems in alluvials. Most of this description will therefore be about alluvials with comments on bedded vis-a- vis alluvial deposits where necessary. Although geological comments refer mainly to lateritic deposits the method of valuation described applies to all bedded deposits, e. g. coal, limestone, phosphate. In general, the more a deposit suffers alteration during or after its formation and the more the sampling process disturbs its material, the greater the difficulties of valuation. Emphasis is laid on structure, as in any kind of deposit valuation cannot proceed until its structures are understood. Not all the structures found in alluvials will occur in bedded deposits, of course.

Jan 1, 1982

By M. S. Celik, G. Onal, S. Atak, A. A. Abramov

An oolitic phosphate ore composed of phosphate (mainly francolite) and carbonates as gangue has been tested for the suitability of the reverse flotation process. The samples were first ground autogeneously followed by the reverse flotation process. While the carbonates were floated by sodium oleate the phosphate was depressed by phosphoric acid. The effect of particle size, reagents type and concentration on flotation recoveries have been investigated to determine the optimum conditions. By this process, a run-of-mine ore containing 16.72 % P205 was upgraded to 28.00% P205 with a recovery of 77.0% The mechanism of optimum flotation with phosphoric acid observed at pH 6.3 is explained based on a relationship involving surface potentials and the ratio of required collector concentrations for the respective minerals.

Jan 1, 1993

By Joseph Cervik, Fred Garcia

Gob holes are routinely used by the mining industry to vent methane from gobs and to prevent it from entering the mine ventilation system. In some cases, flows from gob holes are measured by centering an anemometer on the end of the discharge pipe. These measurements are erroneous and tend to be high by as much as 30%. The Bureau of Mines determined correction factors (method factors) for anemometer measurements taken in this manner. Method factors for 10.2, 15.2, and 20.3 cm (4, 6, and 8 in) ID pipe are 0.68, 0.71, and 0.78, respectively. Comparisons between horizontal and vertical flows indicated no significant change in method factors. Consequently, the method factors for horizontal pipe flows can be applied to vertical upward flows.

Jan 1, 1987

By Anthony W. Wakefield

The paper is intended merely as an introduction to methane hydrates, what they are and why they are important. It does not claim to be a cutting-edge research report, but may be useful for those to whom the subject is unfamiliar.

Jan 1, 2008

By Kenneth P. Katen

Though the use of continuous mining machines consolidated the operations of cutting, drilling, blasting, and loading in one machine that would theoretically provide uninterrupted production, it was soon realized that the face haulage and roof support operations remained as major impediments to continuous production. The ability to provide not only continuous cutting and loading, but also continuous haulage and roof support (see Fig. I), was the basis for the introduction of mechanized longwall systems in this country from Europe in 1951. The early systems employed friction props for roof support, but were to become obsolete shortly after introduction of the first hydraulically powered, self-advancing supports in 1960. Since then, use of the longwall technique has grown to the point where it is currently providing more than 5% of the annual output of underground coal mines in the United States. The shortwall system had its origin in Australia, but was first introduced into this country in 1962 following the development of powered roof supports. It, too, provides for continuous cutting, loading, and roof support (see Fig. 2), but has not experienced the widespread popularity of longwall due to its inherent inability to easily provide for continuous haulage. While there are in the neighborhood of 100 longwall systems currently in operation in this country, there are only a handful of short- wall operations providing production of slightly more than 907 184.7 t/a (1,000,000 stpy) Both of these systems provide uninterrupted roof support for face operations by means of hydraulically powered steel roof supports. In each case, the coal removal consists of open-end cuts made from the narrow end of a large rectangular pillar (panel) which has been blocked out by continuous miners developing entries around its perimeter. However, this is the extent of the similarities between the two systems. It is hoped [ ] that the information presented in this chapter will enable the reader to better understand the two mechanical systems and the mining concepts involved in their employment.

Jan 1, 1981

By H. Köse, C. Tatar, C. Helvaci, F. Simsir

The Çayirhan coal basin is located 124 km (77 miles) west of Ankara,Turkey. With approximately 520 Mt (570 million st) of lignite reserves, the Neogene Çayirhan basin is one of the important coal districts of the central Anatolia region. The Çoraklar formation consists of crossbedded sandstone, channel fill conglomerates, mudstones, carbonaceous shales and volcanoclastic pebblestones, which are fluvial in origin. The lower and upper lignite seams occur, respectively, in the lower and the uppermost parts of the Çoraklar formation. The lignite deposits are in the Çayirhan and Koyunagili portions of the Beypazari Neogene basin. The Çayirhan coalfield consists of lower and upper lignite seams. The lower lignite seam does not outcrop at the surface. Its lateral discontinuity and relatively low sulfur content, plus sedimentologic and stratigraphic features of the associated sediments, indicate a fluvial origin. Thus, the lateral spreading and geometry of the lower lignite deposits were controlled by the channel, flood plain and well drained marshes of a fluvial system. The mining method employed at Çayirhan is the fullymechanized, retreat, working longwall with caving system. Due to ventilation, haulage and tectonic conditions, panel lengths from 0.6 to 1.7km (0.4 to 1.1 miles) are chosen, and 220-m (720ft) face lengths are used. The annual coal production is 2.2 Mt (2.4 million st).

Jan 1, 1994

By Peter G. Chamberlain

Novel and innovative mining methods are attracting the attention of mining engineers at an unprecedented level. Historically, the US mining industry has responded rather conservatively to new technology. The financial difficulties affecting the domestic mining industry in the early 1980s changed attitudes toward new technology. The market contraction during that period, coupled with an expanding world mine capacity, created a serious oversupply of many raw mineral products. Many mining companies found that retaining a share of world markets while making a profit required drastic cost-cutting measures.

Jan 1, 2008

By J. Michael Howard

Holes cored through the Prairie Creek lamproite volcanic complex at the Crater of Diamonds State Park by companies interested in the site's commercial diamond potential give an opportunity to redefine the size and shape of the Prairie Creek pipe. Relationships of cored rock sequences and the discovery of a previously unrecognized major rock type allow a reinterpretation of the sequence and type of intrusive activity. Trench sampling of diamondiferous rock units yielded a diamond content far below what was anticipated based on an estimate from historical records. Inadequacies of shallow bulk-testing methods for a diamondiferous pipe are examined.

Jan 1, 1999

By P. Bevilacqua, G. Ferrara, M. C. Williams, T. P. Meloy

Tabling is an old environmentally friendly separation unit operation. This paper models shaking tables and explores the action and design of riffles on shaking tables. By reassessing riffle shape and riffle patterns, significant improvements in tabling performance appear feasible. While table sales appear at their nadir, a high-tech environmentally friendly table may have a significant market in the coming decade. Riffles on a shaking table impact particle separation. Particles are affected by riffles and their exit position on the table is dramatically changed, Riffle shape determines how much the riffle will influence a given material. Moreover, riffle patterns influence the concentration of a given material and its exit points on a table. This effect of riffle placement and design is modeled in a spreadsheet. Major performance and separation improvements may he expected by improved table design. Two physical laws of tabling have been derived. These laws aid in the design of sophisticated high-tech tables.

Jan 1, 1995

By G. Brooks, J. T. Ellington, M. Yensco, G. E. Mcquien, M. T. Ityokumbul

Coarse silica flotation from intermediate pebble (IP) product has been carried out a pilot plant Dual Extraction Column (DEC) at an operational phosphate mine in Central Florida. The solids feed rate ranged from 4.16 – 5.3 TPH while the amine dosages ranged from 0.32 – 0.93 lb/T. The optimum amine dosage when using recycled process water was deter-mined to be 0.6 lb/T. With a feed containing 40-45 BPL and 38-45% insol, the results show that the IP can be upgraded to 56-61 BPL and insol of 16-22% at 85-90% BPL recovery. The results show that the DEC is an effective device for flotation of coarse silica from the IP. The advantages of upgrading the IP prior blending with the pebble are presented and discussed.

Jan 1, 2004

By R. L. Garrett

The quality of mineral additives used in a drilling fluid (mud) can dramatically affect the fluid's properties and the overall cost of drilling an oil or gas well. The principally wed minerals are bentonite, barite, barite/hematite blends, and hematite alone. The high specific gravity minerals, barite and hematite, are used to increase drilling fluid density. Bentonite clay is used to increase drilling fluid viscosity and gel strength and to provide a low permeability filter cake. A multimillion dollar investment in a well and the safety of the personnel on the drilling rig can depend on how effectively these mud additives perform with other constituents in the mud. This paper points out effects caused by small amounts of certain carbonate and sulfide mineral impurities in barite or hematite and how polymeric extender additives in bentonites contribute to unpredictable behavior of a mud. Effects like these are the reason oil companies using these materials sometimes set their own quality standards beyond those already specified in APZ Spec. 13A. Also discussed in this paper are the current standardization activities of API Committee 13 on these minerals.

Jan 1, 1988

By Richard M. Crowell, John W. Shield

GeoBiotics has developed a biooxidation technology (patents pending) which involves coating refractory precious metal sulfide concentrates onto a support material and biooxidizing the sulfides in a heap configuration. The concentrates are produced from low or high grade sulfidic refractory ores or existing mine tailings. The process has been found to achieve high gold recoveries asso­ciated with stirred tank biooxidation, but at the low operating and capital costs associated with whole ore heap biooxidation. Improved gold recoveries of up to 98% after biooxidation are reported for 4 representative mines or deposits. The sulfide flotation concentrates were studied using 3 and 6 in. diameter columns or 3 in. drained vats. The refractory sulfide concen­trates biooxidize rapidly in 3 to 12 weeks with substantial increases in subsequent gold recovery.

Jan 1, 1996