Search Documents

By T. J. Lutz, S. Gallagher, J. R. Srednicki, J. J. Sammarco

The Illuminating Engineering Society of North America reports that an underground mine is the most difficult environment to illuminate (Rea, 2000). Researchers at the U.S. National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) are conducting ongoing studies designed to explore different lighting technologies for improving mine safety. Underground miners use different visual cues to escape from a smoke-filled environment. Primary and secondary escapeways are marked with reflective ceiling tags of various colors. Miners also look for mine rail tracks. The main objective of this paper is to compare different lighting types and ceiling tag colors to differentiate what works best in a smoke-filled environment. Various cap lamps (LED and incandescent) and lasers (red, blue, green) were compared to see which options resulted in the longest detection distances for red, green and blue reflective markers and a section of mine rail track. All targets advanced toward the human subject inside of a smoke-filled room to simulate the subject walking in a mine environment. Detection distances were recorded and analyzed to find the best cap lamp, laser color and target color in a smoke environment. Results show that cap lamp, laser color and target color do make a difference in detection distances and are perceived differently based on subject age. Cap lamps were superior to lasers in all circumstances of ceiling tag detection, with the exception of the green laser. The incandescent cap lamp worked best in the simulated smoke compared to the LED cap lamps. The green laser was the best color for detecting the tags and track compared to the red and blue lasers. The green tags were the easiest color to detect on the ceiling. On average, the track was easier for the subjects to detect than the ceiling tags.

Jan 1, 2013

By Tim Langmaid, Steve Skelhorn, Stephanie Robillard, Allen Mitchell

"The Port Mann Main Water Supply Tunnel project provides a critical water main crossing of the Fraser River for the owner, Greater Vancouver Water District (Metro Vancouver). The project consists of two 60-metre-deep slurry panel shafts and a 1-kilometre-long, 3.5-metre excavated diameter tunnel located near Vancouver, British Columbia, Canada. The initial tunnel lining is a precast concrete steel fiber reinforced gasketed segmental lining. The final lining is a 2.1-metre-diameter welded steel pipe. This paper describes the challenges encountered during tunnel construction and the solutions implemented. Key challenges include earth pressure balance tunnelling at up to 6 bar pressure—the highest to date in Canada—a water-crossing without surface access for the majority of the tunnel drive, ground freezing from a river platform for a critical TBM intervention, and boring through cobbles and boulders in dense glacial till. INTRODUCTION Metro Vancouver supplies drinking water to 18 municipalities, one electoral district and one treaty first nation, serving a population of more than 2.4 million residents. Water is collected in three mountainous watersheds to the north of the Greater Vancouver area, in southwestern British Columbia, Canada. To supply the growing demands of Metro Vancouver’s customers, treated water must be conveyed across two significant water bodies: the Burrard Inlet and the Fraser River. The existing Port Mann water main is one of several key links between the watersheds north of Vancouver and the municipalities south of the Fraser River. The Port Mann Main Water Supply Tunnel (PMMWST) is the first of a series of upgrades, to increase capacity, enhance scour protection, and improve seismic resilience. The new tunnel is 3.5 metres (11.5 ft) in diameter and 1 kilometre (0.6 mi) long. When completed, it will contain a new 2.1 metre (7 ft) diameter steel water main that will help ensure the continued, reliable delivery of drinking water to these municipalities, and will more than double the capacity of the existing 1.2 metre diameter main."

Jan 1, 2016

By William Gleason

At 6,898 ft below surface, the historic No. 9 shaft at Resolution Copper near Superior, AZ is now the second deepest single lift mine shaft in the United States and connects to the deepest single lift mine shaft in the U.S., Resolution Copper’s No. 10 Shaft (6,989 feet). The shafts serve as ventilation and access for future underground development of what could one day become one of the most significant copper mines in the United States. It is from the base of No. 9 and No. 10 shafts that hundreds of employees of Resolution Copper, a joint venture of Rio Tinto and BHP, hope will soon be given the go ahead to begin driving lateral tunnels to reach a copper deposit that is estimated to contain 28 Mt or 40 billion pounds of copper. Copper was recently added to the U.S. Geological Survey’s (UGGS) critical minerals list, in large part because of increasing demand. A study by S&P Global Energy & Market Intelligence “Copper in the age of AI: Challenges of electrification” released on Jan. 8, 2025, “identifies a transformative trajectory for copper demand, projecting a surge from 28 Mt (31 million st) in 2025 to 42 Mt (46.3 million st) by 2040 – a 50 percent increase that underscores the metal's pivotal role in multiple technological and economic domains.” The surge in demand is driven in large part by the global energy transition, electrification of vehicles, growth of artificial intelligence and data centers, and most recently robotics. Meanwhile, geopolitical tensions have increased the focus on the need for the United States to secure more of its own mineral supply chain. S&P Global’s report is one of many warnings that while copper demand has accelerated rapidly, future supply is being held back. Resolution Copper stands out as one example of a known mineral deposit remaining locked in the United States’ complex and lengthy permitting slog.

Feb 1, 2026

By M. S. Prasad, K. J. Reid, M. P. Katsoulis

The State of Minnesota is interested in stimulating the development of clay resources and recently supported a two-year project to collect data on geological, mineralogical, processing, economic and environmental aspects of such potential developments. This paper presents the various process options adopted on bulk samples collected from the Minnesota River Valley area, which is a primary deposit and contains a major silica fraction. A standard test flowsheet involving degritting, dispersion. HGMS and cycloning was developed and for some samples yielded an acceptable filler grade product. Secondary streams containing relatively high grade kaolin but of coarse size were also obtained. Improvement in particle size distribution and in physical properties related to paper product specifications (brightness, viscosity) were obtained by size-reduction processes. Market and economic considerations for kaolin consumption in the upper Midwest are analyzed. Current markets for paper grade kaolin in Minnesota are briefly discussed.

Jan 1, 1992

By J. Maiti, A. Bhattacherjee

A literature review on quantitative analysis of mine safely studies revealed that numerous investigators explored a wide- range of techniques, including the investigation of bivariate and multivariate statistical models. Although these researchers addressed various issues of accident causation and prevention, they, in general, did not investigate through the use of quantitative models the multivariate relationships of several factors affecting mine safety in a causal framework. In this paper, systems dynamics and structural equation modeling are presented to simultaneously represent and study the effect of policy variables related to accident prevention along with the factors causing accidents and injuries. The application of these models to a group of mines revealed that current training practices at these mines do not appear to alleviate accident occurrences. It is inferred that the use of these quantitative techniques can provide a new direction of research in mine-safety studies.

Jan 1, 2000

By Paul D. Dupree

Introduction Trapper mine is a dip-line strip coal mine, located about 10 km (6 miles) southwest of Craig, CO. The mine provides the Craig Generating Station, operated by Colorado-Ute, with about 2 Mt (2.3 million st) of coal annually. The Trapper mine is situated on a hillside that climbs in elevation from 2 to 2.5 km (6500 to 7400 ft) at average grade of 15%. The coal seams dip at about 16% down-grade and they outcrop near the top of the hillside. They exceed maximum stripping depth in 1 to 1.7 km (3500 to 5500 ft) of pit length. Stripping in the three existing pits is performed with three Page 752 23 m3 (30 cu yd) walking draglines. Two of the pits are currently being cast blasted. Until the active cut, the Derringer pit was cast blasted only where the lower mined seam exceeded stripping capabilities and the pit was a single seam operation. Now, a 9-m (30-ft) interburden bench has been incorporated into the stripping plan. This bench protects the first seam of coal from shear when the overburden is cast blasted. The cast blasted section of the 1.6 km (53,000 ft) long pit has been increased from the 457 m (1500 ft) casted previ¬ously to 1 km (3500 ft). High speed films show the coal losses due to shear of the blast are minimal. The pit width in Derringer pit is 61 m (200 ft). This is necessary for efficient spoil side stripping of a relatively thin interburden in the two-seam section of the pit. The Enfield pit is entirely cast blasted. The single seam pit is 46 m (150 ft) wide, 1.1 km (3600 ft) long, and varies from 15 and 46 m (50 and 150 ft) in overburden depth. The overburden strata at the mine consists of medium-hard layers of sandstone, shale, and

Jan 1, 1987

By Andrew I. Hustrulid

The discrete element method has successfully been used to model the behavior of material flow in transfer stations. With position, velocity, and applied forces for every particle and boundary in the simulation available at increments of 10-5 seconds, the next critical step is the presentation of this data in a concise and beneficial form. This paper discusses several methods of presenting the data from discrete element simulations that are used to improve the performance of a transfer station. These measurements are also used as a learning tool to better understand and visualize how material transfers from one belt to the next.

Jan 1, 1998

By Charles A. Rhoades

The Bureau of Mines is conducting research on a dual leaching method that offers the potential for the economic recovery of the silver as well as the manganese contained in some of the domestic manganiferous silver deposits. The method is an initial leach of the manganese with aqueous SO2 followed by a neutralization rinse, and then by a second leach for the extraction of silver with cyanide solution. Refractory silver in these ores is either bound by the high-valence manganese, chemically resistent to cyanide leaching, or is rendered inaccessible to cyanide leach solution by the surrounding manganese mineralization. Less than 10 pct of the silver was extracted when -1 in +1/2 in (-2.5 cm + 1.3 cm) ore pieces were leached directly with cyanide. However, extractions of 25 to 82 pct for silver and 65 to 96 pct for manganese were attained in laboratory column leach tests using the dual method on the same size ore pieces from six domestic deposits.

Jan 1, 1984

By W. D. Macleod

This paper describes a mineral dressing process for the upgrading of tin ores. The process described is called 'agglomeration' and. is similar in many respects to flotation. Many variables have been examined experimentally both on batch and continuous operations and are reported upon herein... Using a Mt. Pleasant tin ore, assaying 0.5% Sn, an upgrading to 8% Sn, with a recovery of 95% could be obtained by this process.

Jan 1, 1966

By Euclid P. Worden

In 1977, an article in World Mining (1) reported a total of 2726 rotary blast hole drills in service. This figure included only those machines produced by three of the manufacturers building drills of this type. The total, therefore, is much higher: Rotary drilling in the mining industry is big business to the manufacturers and suppliers involved, and a significant cost item, to mine operators. The time has come to take a hard look at rotary drilling technology with an eye to re¬ducing costs by increasing drilling efficiency. The efficiency of any rotary drilling operation is measured in terms of the rate of penetration achieved by the bit. In blast hole drilling, five factors affect the rate of penetration. They are: 1. Bit selection 2. Weight on the bit 3. Rotary speed 4. Hole cleaning 5. Formation properties Of these factors, all but one may be control¬led by the operator. Looking at any one in detail may reveal possible improvements in the system. Cleaning the hole is a good place to start. In order for a bit to perform at its maximum capability, each tooth or insert should strike fresh, clean rock as it falls into its drilling position. If the tooth or insert lands on previously drilled cuttings, a major portion of the energy delivered to the bit is absorbed in re drilling this broken material. A major portion of the interest, therefore, should be directed to the proper cleaning of the bottom of the hole.

Jan 1, 1979

By Ron Robinson

Booster fans have been in regular use in British coal mines since the first half of this century, but a large increase in their use did not take place until after the Nationalization of coal mines in 1947. From that time the need was identified to improve standards of ventilation in general and mining engineers specializing in ventilation were appointed at all levels in the mining industry. A comprehensive approach to ventilation surveys and planning, together with the realisation of the benefits of booster fans, led to their more rapid introduction. Many coal mines in the U.K. are at moderate depth and have virgin strata temperatures of 30°C or less. The ability to control climatic conditions by increased ventilation rather than resort to cooling systems has led to the introduction of booster fans and recirculation systems in these mines. Large makes of methane and high levels of coal dust production due to increased mechanization have also required enhanced ventilation standards. This paper deals with the reasons for selecting booster fans and the specific safety considerations involved in their use. Numbers, types and sizes of booster fans in the U.K. are outlined, together with notes on installation and performance. Remote monitoring and control from the surface is dealt with, and current legislation. The evolution of controlled recirculation is also covered starting with auxiliary fan systems in 1970 and leading to very large district schemes in the late 1980s. The research at Newcastle upon Tyne University and other establishments in the climatic conditions associated with recirculation is summarised and its use in assisting existing and proposed conventional and recirculation systems is indicated.

Jan 1, 1989

By Joseph Kurtak

When prospectors discovered mineralized outcrops in Pine Creek Canyon in 1916, little did they know the site was destined to become one of the world's greatest tungsten mines. Located outside Bishop in California's rugged Sierra Nevada mountain range, the mine's development imposed unique challenges to the hardiest of mining men. In its early years, the Pine Creek operation was plagued by bad luck and poor timing. But through the perseverance of a dynamic group of mining personalities, it would gain world class status. Pine Creek tungsten supplied much of the defense needs of the United States during World War II and put the Bishop area on the map as a major contributor to the nation's stockpile of strategic metals. The mine's history was shaped by world politics, the ups and downs of metals demand and economic survival through technological innovations. In contrast to many mines, Pine Creek's workings went horizontally into and then up inside the mountains - nearly to the ridgetops. This resulted in the name "Mine in the Sky" being attached to the operation. The origin of Pine Creek's ore bodies is related to the emplacement of a portion of the Sierra Nevada batholith about 100 million years ago. During the intrusive process, granitic magmas engulfed overlying calcareous sedimentary rocks, flooding them with silica-rich hydrothermal fluids and metamorphosing them to skarn. The fluids also contained tungsten, molybdenum and copper. They precipitated as scheelite, molybdenite and chalcopyrite, respectively, during the metamorphic process. The ore-bearing skarns occur as near-vertical tabular pendants in the intrusive rocks. These were later exposed by the uplift of the Sierra Nevada mountain range and glacial erosion.

Jan 1, 1998

Cost reduction programs can focus on total cost or unit cost, but unit cost is usually the principal objective. The production cost per unit is: [Unit cost = Total cost Production volume] Consequently, any activity that reduces the total cost or increases the production volume will reduce the unit cost. Production volume is increased by (1) maximizing the availability of the production equipment and (2) maximizing equipment performance during periods of operation. Most operations managers routinely focus on volume because the factors influencing volume are generally well understood and congruent with the managers' technical skills. In fact, production volume (as a percentage of maximum achievable capacity) is widely recognized as one of the most significant measures of operational performance.

Jan 1, 1999

By G. Van Weert

Separation of minerals by shape has received little attention, since minerals normally do not break into different shapes during crushing and grinding. However, comminution of consumer wastes generates opportunities for novel separations based on particle shape. For instance, ductile plastics are broken into longer curved shapes, whereas brittle plastics yield angular particles. Using spouting beds for particle separation in water requires controlling the spout's instability. The preferred geometry for such redesigned spouting beds is reported. Plastic cylinders, discs and spheres were separated as a function of rising water velocity and amount of particles in the system. By using 5 mm particles, differences in settling behavior could be video recorded.

Jan 1, 1999

By K. E. Brown, T. D. Murphy

At Monterey Coal's No. 1 Mine in central Illinois, it became necessary to predict if the sulfur content of individual trainloads of coal would exceed a contract sulfur maximum. Using geostatistics and Monte Carlo-type simulations, a forecasting procedure was developed to meet this need. The developed procedure predicts the monthly, mean sulfur content of the coal shipped and the probability of individual shipments exceeding the contract limit. During the first five months of using this procedure, the forecasted, monthly mean sulfur value was within 0.03% of actual. This represents a significant improvement over the inverse-distance, gridding-based, forecasting used previously.

Jan 1, 1994

By R. D. Beard

Puerto Rico lies within the remnants of a deformed Cretaceous island arc system in the northeastern Caribbean. The Island can be divided into three broad geologic provinces: the Central Volcanic-Plutonic Province (Lower Cretaceous to middle Eocene), and the Northern and Southern Limestone Provinces (early Oligocene to middle Miocene). Known precious metal deposits are generally small and occur in veins and shear zones within Lower and Upper Cretaceous volcanic and plutonic rocks. Some Tertiary igneous rocks are also mineralized. Selected indications of disseminated lithology-controlled mineralization could represent larger deposits. Associated metals in some deposits include copper, zinc, and lead. At present, tax policies, population density, political outlook, and lack of proven significant precious metal deposits discourage the establishment of a metal mining industry.

Jan 1, 1993

The classical slope analysis and a statistical technique were used in order to determine the iron complexes formed in the organic phase during the extraction of Fe(III) from Fe-Ni-Co sulfate solutions with Di-(2-ethylhexyl) phosphoric acid (D2EHPA) in kerosene. Equilibrium constants for the extraction based on these complexes were also calculated. The complexes determined were of the general form (Fe(OH)3-nRn?sHR)x' where n varied between 1 and 2.5 and s between 0 and 3, and both were found to be decreasing as the iron loading in the organic phase increased. Values of 1,2 and 3 were generally found for x, indicating that the complexes were monomers, dimers and trimers.

Jan 1, 1988

By J. W. Jang

The wear behaviors of grinding media with different chemical compositions and microstructures in wet grinding of a quartz-pyrrhotite mixture was investigated under various environments. The marked ball wear tests showed that the wear rate could be minimized by a suitable combination of martensite and ferrite within the same ball. A ball composed solely of hard martensite exhibited increased wear under an oxygen environment, while balls composed of both soft ferrite together with hard martensite exhibited decreased wear due presumably to the difference in their passivation? behaviors. The galvanic interactions between the two phases as well as among these phases and an electroactive mineral were investigated through electrochemical measurements under abrasive conditions in a slurry. The rates of formation of passive films controlled the corrosion currents of the high chromium steel media. Corrosive wear and its effect on flotation are discussed using the passivation kinetics model thereby developed.

Jan 1, 1989

By J. B. Knaebel

I have been asked to discuss the "Development of the Twin Buttes Mine for Production." This property, which is a large low-grade open pit copper mine about 25 miles south of Tucson, Arizona, was recently brought into production by The Anaconda Company under a long-term lease agreement with the Banner Mining Company. Since the scope of this paper is limited to the subject broadly indicated by its title I will confine discussion of historical, environmental and other general matters to a brief summary sufficient, I hope, to establish a background of those conditions which influenced our approach to the technical and economic problems that faced us at Twin Buttes. The paper deals primarily with our studies and activities related to the solution of these problems and with the resulting engineering and business decisions that were taken - decisions which culminated last September in the initial commercial operation of another major open pit copper producer unique and interesting in several respects.

Jan 1, 1970

By O. E. Etheridge Jr., R. A. Lowe, C. I. Basilio, J. M. Randolph, S. W. Sheppard

The low-shear viscosity of kaolin slurries is one of the principal characteristics that determine whether a clay can be utilized for paper and ceramic applications. In this work, the causes of high low-shear viscosity and methods for improving the rheological behavior of the slurries were investigated. The presence of fine-grained smectite impurities within the kaolin was shown to detrimentally affect the low-shear rheology of the slurries produced from these clays. It was also shown that mechanically working (i.e., pugging) a crude kaolin followed by desliming to remove these impurities can reduce the low-shear viscosity.

Jan 1, 2000