Search Documents

By M. S. Klima

Tests were conducted to investigate the potential for recovering anthracite from preparation plant tailings. Samples were collected from tailings streams or slurry ponds of several anthracite cleaning plants. A washability analysis was conducted on each sample. The use of gravity-and surface-based cleaning processes for treating the 28x200 mesh tailings material was examined. Simulations were performed for various cyclone staging arrangements using published partition data for both water-only and dense-medium cyclones. Froth flotation testing was done on both precleaned anthracite and tailings material. Grade-yield curves were determined for various conditions.

Jan 1, 1995

By B. K. Parekh

Large reserves of coal pond fines are found in the Illinois Basin-over 40 million tons in Western Kentucky, over 65 million tons in Southern Illinois, and over 35 million tons in Southern Indiana. If these fines are used to produce coal-water slurry (CWS), fuel costs, NOx. emissions, and pond closure costs can be reduced. Coal fines from this region that are used to produce CWS for co-fire or re-burn may require processing, however, to attain proper particle size distribution and fuel quality. To evaluate the effectiveness of using coal cleaning technologies to control these CWS quality parameters, a simple flowsheet for recovering and processing coal pond fines was designed and tested. Coal fines processing consisted of using classifying cyclones to size at nominal minus 200 mesh, cleaning the classifying cyclone underflow using spirals, and cleaning the overflow using column froth flotation. Ash content of the dean coal from the spiral was reduced to about 10 percent, which is satisfactory to use for CWS co-firing in a cyclone-fired boiler. The clean coal from column flotation may be used for re-burn in a cyclone-fired boiler or as co-fire fuel in a wall-fired or tangentially-fired boiler. Heating value recovery during laboratory-scale, pilot-scale, and commercial-scale coal cleaning testing was about 80 percent.

Jan 1, 1998

By W. S. Weldon

The use of spiral separators for the beneficiation of fine coal typically in the size range -2+0.1mm is now well established process technology. Developments during the mid 1980's resulted in the production of cost effective, efficient large diameter coal spiral separators. Recent developments and research have been geared to optimize metallurgical performance, materials handling and equipment geometry of large diameter coal spiral separators.

Jan 1, 1997

By R. K. Singhal

This new tool can be used for the proper assessment of the potential economic wealth of any risky capital project. It does provide an unambiguous recommendation of the type "go or no go" to the decision-maker simply by comparing two different ratios profit/investment. One ratio determines the minimum value required to at least break-even while the other measures a probable value based on the asymptotic theory of statistical extremes (weakest link concept). Its application is briefly illustrated by means of an underground gold mine project, an oil sands mine project and a poly-metallic open pit project.

Jan 1, 1993

By Mark A. Alspaugh, E. A. “Bud” Viren

The driving force behind most advances in technology is need. In the early 1980s, underground coal miners in the USA wanted to build longer conveyors to handle larger capacities but continue to use fabric reinforced belting with mechanical fasteners. Conveyors with intermediate drives were certainly the answer but achieving reliable designs required a significant learning curve. Basic design methodologies had to evolve including advanced simulation of starting and stopping along with complex control techniques and logic. Some components also evolved as specific performance requirements changed Today, in addition to underground mining, the technology has been used extensively in the tunneling industry where the need is for control of belt tensions to negotiate tight horizontal curves. Even though intermediate drives are not used extensively on the surface yet, the lessons learned will find their way to long overland surface conveyance where smaller components are more available and reliable, and often with less capital cost. This paper will document the evolution of intermediate drive technology over the last 30 years and will show examples of its current use.

Jan 1, 2004

By W. K. Dressel

Over 2 million tons of steel furnace dusts are produced each year in the United States. Recycling of these dusts rather than disposal would conserve mineral resources, reduce land requirements for disposal, and decrease pollution. In addition to the iron content, the dusts contain appreciable amounts of zinc and lead. Removal of lead and zinc with simultaneous reduction of Iron oxide has been achieved by inert atmosphere roasting of carbon-containing pellets prepared from steel furnace wastes. High- and low-carbon wastes were blended to obtain mixtures with sufficient carbon to serve as a reductant during subsequent roasting. The mixtures were pelletized with the addition of bentonite and water, and the dried pellets were roasted in a stream of nitrogen at temperatures ranging from 900" to 1,150° C. Zinc and lead contents were reduced to the 0.1 percent level or less by roasting mixtures containing as little as 7 percent carbon for 1 hour at 1,100° C. ton metallization increases with available carbon content; 50 percent metallization is achieved with 7 percent carbon, 85 percent metallization with 12.5 percent carbon, and over 95 percent metallization when the pelletized mixtures contained in excess of 20 percent carbon.

Jan 1, 1973

By Matthew J. Hrebar

Dragline stripping operations account for over one-half of the U.S. bituminous coal production mined by surface coal mining methods. The dragline is a popular stripping tool because of its flexibility in varying overburden depths and relatively low operating costs per cubic yard of overburden. Because of the relatively high capital costs of the machines and their use as a primary stripping tool, the selection process is an important step in the mine planning procedure.

Jan 1, 1979

By S. Chunhui, W. Anbin, R. B. Cook

The Xicheng is one of China's largest lead-zinc (Pb-Zn) districts with known minable reserves in excess of 10 Mt (11 million st). The centrally located Changba-Lijiagou and nearby deposits are representative of the district. They consist of stratiform and stratabound zones of pyrite-sphalerite-galena mineralization within deformed, moderately metamorphosed Middle Devonian clastic and carbonate units. When considered with other similar districts that extend for several hundred kilometers to the east, a major episode of Devonian sedimentary exhalative mineralization is indicated.

Jan 1, 1992

By Morton Handelman

The extraction of aluminum oxide_ from its ore is the initial step in the commerical production of metallic aluminum. This is most commonly done by the Bayer Process in which a caustic solution is used to dissolve hydrated alumina from the insoluable materials with which it is associate in bauxite. At the two-thousand ton per day Sherwin Alumina Plant of Reynolds Metals Company, the extraction residue from Caribbean ores is removed from the main pro¬cess stream as the underflow of a continuous clarifier-thickener operation. This sludge, prior to its ultimate r4jection from the process, is washed in a nine-step continuous countercurrent decantation system to recover physically-entrained mother liquor. Control of alumina production costs requires the optimum recovery of solubles from this residue which is generated at the same rate as the finished product. The equipment, operating techniques, controls and process variables which affect the efficiency of this soda recovery from Bayer Process red mud will be discussed.

Jan 1, 1959

By R. A. Lowe

Smectite is a common impurity in the kaolins of Georgia. This impurity is harmful to the low-shear rheology of kaolin slurries in concentrations as low as a few weight percent. The deleterious effect of smectite on the low-shear rheology is due to the swelling of the mineral. Montmorillonite containing clays were treated to precipitate a compact brucite layer {Mg(OH)2} in the interlayer region of the expandable layer silicate mineral. This treatment forms a hydroxy-Mg-montmorillonite with characteristics similar to chlorite. This treatment effectively reduces the swelling capacity of the mineral and improves the rheological properties of kaolin slurries contaminated with smectite impurities.

Jan 1, 1999

By A. G. Sciulli, G. P. Ballock, K. K. Wu

This paper discusses common environmental problems associated with coal refuse disposal. It suggests design concepts to minimize potential hazards. Discussion focuses on site selection, embankment design and construction, site preparation, facility operation, abandonment, and reclamation. It emphasizes measures that should be adopted in the design phases and during construction of the facility. Recommendations are also made concerning special problems, including seepage, ground water contamination, and mine sealing.

Jan 1, 1987

By Richard I. Grass

The White Pine Mine is located 4- 1 /2 miles south of Lake Superior in the western part of Michigan's Upper Peninsula. The orebody occurs in tabular, gently dipping Keweenawan sediments. GEOLOGY The orebody outcrops beneath 30-50 feet of Pleistocene clays and dips to the east and northeast to a depth of 3, 000 feet in five miles. It lies midway between the Porcupine Mountains and the Bergland Hills, both of which are steeply dipping felsite and coarse porphyry intrusives, extrusives and sediments (Figures 1 and 2). The orebody sediments were deposited in the Keweenawan basin during mid- and upper Keweenawan times. Mineralization occurs in the basal 20 to 25 feet of the Nonesuch formation, which is made up primarily of laminated siltstone s. Native copper, chalcocite, and silver are the ore minerals. The ore is mined by trackless room-and-pillar methods.

Jan 1, 1967

By B. S. Graves

Deep well disposal of selected industrial wastes has been proved feasible and acceptable in the New Orleans area by several industries including Shell Oil Company's Norco Refinery and Chemical Plant where three of the six successful disposal wells in this area are operating. Well design and procedures for restoration of capacity are based, in most cases, on the principles of brine injection developed by oil producers in South Louisiana. Geological formations in the Gulf Coast area are suited to this type of injection because receiving strata are porous, isolated from sources of potable water and their water is compatible with the liquid wastes to be injected. This method of disposal is a simple, complete and economical solution to the problems presented by certain hard to treat wastes.

Jan 1, 1964

By John L. Stafford

The ROEMMC combustion system was originally conceived as a means of utilizing solid fuels that would otherwise have been wastes requiring disposal and convert these fuels into useful energy sources. This concept follows as an extension of the application of residual waste incineration with energy recovery practiced in the lumber, manufactured board, sugar cane, and other industries. The incineration of these wastes in the furnaces of steam generating equipment is thoroughly described (1, 2, 3, 4, 5, 6, 7). The fundamental principle of the ROEMMC system is temperature control which makes possible the maintenance of the non-combustible fraction of these solid fuels in a dry solid state and their separation from the gaseous products of combustion. This philosophy of ash removal and the "slagging" philosophy are compared. The ROEMMC equipment function and applications are described.

Jan 1, 1978

By Paul G. Schmidt

The Crandon massive sulfide deposit Forest County, Wisconsin, was discovered by Exxon Minerals Company, U.S.A., in July 1975. Announced estimated in-place reserves are 62 M metric tons (70 million short tons), grading about 5% zinc and 1% copper. The reserves are evenly divided between massive sulfide are and stringer sulfide ore. The sulfide body is associated with Precambrian felsic pyroclastic rocks, and it is overlain by intermediate volcanic rocks and their derived sedimentary rocks. These rocks were subjected to greenschist facies metamorphism and were tilted to a near-vertical attitude. Geologic observations indicate a submarine-volcanic-exhalative origin for this deposit.

Jan 1, 1978

By J. L. Francke

This paper describes the practices and methods used in a study of Time Domain Reflectometry (TDR) as an inexpensive deformation monitoring tool in underground excavations at the Waste Isolation Pilot Plant (WIPP). The WIPP is being developed near Carlsbad, New Mexico, for the disposal of transuranic nuclear wastes in bedded salt 655 m (2 150 ft) below the surface. Data collected from WIPP geomechanical monitoring are used to characterize conditions, confirm design assumptions, and understand and predict the performance of the deep salt excavation. The geomechanical monitoring program encompasses numerous geomechanical monitoring techniques ranging from inspection of observation boreholes to advanced radar surveys. In 1989 TDR was introduced as a monitoring tool with the installation of 12.7 mm (0.5 in) diameter TDR cables in the underground excavations. In 1993, a new TDR system was installed in a separate location. Based on experience with the previous installation, enhancements were implemented into the new TDR system that: 1.) extended the period of performance by increasing cable diameter to 22.2 mm (0.875 in), 2.) increased accuracy in locating areas of deformation by aligning cables with nearby observation boreholes, and 3.) improved data acquisition and analyses using a standard laptop computer, eliminating the chart recorder previously used. In summary, the results of a correlation between the TDR signatures to nearby observation boreholes and geomechanical instrumentation will be presented.

Jan 1, 1996

By Gary Peach, Peter Mason

Planning and estimating progress rates and costs for tunnelling is always best done based on experience and historic precedent. Much precedent is available but the use of data monitoring, data mining and other retrieval techniques on modern TBM machines can enable this to be further expanded and refined. Advance rates can be related much more closely to rock types as can associated rock bolt and mesh/ shotcrete requirements. This in turn can lead to a further refinement in best likely combinations of equipment, such as shotcrete jumbos, better selected for the anticipated conditions, rather than the potential advance rates of the machine. Efficient and timely construction of the tunnel will also be linked to times needed for finishing work, such as contact and void grouting and to how this can be initiated while the TBM is still in operation, in order to save overall construction time. Indeed, this in turn may affect the most preferable layout and construction details of the permanent tunnel. Considerable experience has been gained in the use of two large diameter TBM tunnel drives through the Himalayas at the Neelum-Jhelum hydropower project in Pakistan. All the above aspects will be discussed in the paper based on the considerable experience and data which came from that operation, including appropriate measures in highly stressed areas potentially subject to rock burst.

Jun 13, 2021

By Dirk van Zyl

Three conditions are required for a risk to be realized: (1) a source of risk (i.e., hazard) must exists (2) some process must take place which will lead to the exposure of people, animals, and/or the environment to the hazard: and (3) as a result of the expense, undesirable effects are produced on the people, animals, and/or the environment. A comprehensive risk assessment addresses all three of the conditions through the following four steps: (1) risk source (hazard) characterization, (2) exposure assessment, (3) dose-response assessment, and (4) risk estimation. Although the terminology may differ, the overall approach of financial, public health, and environmental risk assessments is the same (National Science Foundation, 1985).

Jan 1, 1988

By R. P. King

The MODSIM mineral processing plant simulator is used to find optimal combinations of target separation specific gravities in a typical modem coal washing plant. A plant that is set up with these optimal targets can deliver up to 10% more yield at the same ash content as the same plant set up with separation targets chosen by conventional methods. MODSIM is the only simulator currently available that can simulate the liberation of pyrite and other mineral matter during open-and closed-circuit grinding operations. The simulator can therefore be used to assess the benefits of grinding operations in the flowsheet.

Jan 1, 1997

By John C. Kleiber

From time to time since the initial installation of an experimental flotation section in 1940 (reference A), Permanente Cement Company has made efforts to beneficiate the low-grade limestone fraction which occurs in its deposit at Permanente, California, The encouraging results outlined in this paper are the result of Permanente's latest effort. This paper discusses the factors governing the selection of the flowsheet with particular reference to marketability of the sand tailing by-product. The process flow is outlined in detail, and operating statistics of the plant are presented. Finally, the problems encountered in the operation of Permanente's beneficiation plant are discussed as well as solutions sought and found.

Jan 1, 1964