Search Documents

By B. T. Stanley

Traditional methods of creating a water tight shaft liner involve the use of segmented or welded steel. When shafts are located in ground that exhibits extremely difficult conditions of high water inflow and hydraulic pressure, composite liners are often combined with ground freezing during construction. The authors were searching for a cost effective and more flexible solution to hydrostatic liners design than the traditional concrete/steel composite design used so far. Searching through new technologies developed for tunneling applications, sprayed on membranes systems seemed very promising but were not developed for the specific circumstances encountered in shaft sinking applications where ground freezing is involved. Even though freezing is a very effective technique, it creates adverse temperature conditions for the application of spray on membranes. In addition, application and hydrating cure times for those membranes products ranged between six to twenty-four hours under ideal conditions (usually temperatures well above freezing point), which eliminated them from consideration in a shaft sinking cycle. While researching different spray on membrane materials, it was discovered that Stirling Lloyd Polychem Ltd. has developed and proven a different membrane material for waterproofing liners in different tunneling applications. The characteristics of the membrane exceeds the pressure parameters encountered in frozen shaft sinking operations, and the chemical cure times were reduced to one hour per layer which worked well into the shaft sinking cycle times. More over their system included a quality control procedure that allowed insuring integrity of the membrane at application time, a very desirable feature for shaft liner construction. However, the frozen rock surface still presented an unknown in the cure time and stability equation. As all membrane products a shotcrete substrate is usually required prior to application. The hypothesis used by the author was to use this shotcrete layer, not only as a substrate, but also as a thermal insulation against the frozen rock and the membrane during both application and curing time. The authors knew from experience that shotcrete could be applied successfully over frozen rock. But the shotcrete temperature curve over time was unknown and no information were found in the available literature. Testing was required to determine whether a suitable mix of shotcrete could be applied to the frozen shaft wall to provide enough heat of hydration for a suitable period of time to create conditions suitable for membrane application and curing.

Jan 1, 2012

By J. A. M. Cano

An extensive research work was developed by Samarco Mineracao S/A to study the quality characteristics of blast furnace pellets produced with high content of MgO. Comparative blast furnace simulation tests were conducted both in Samarco and foreign laboratories. The objective was to evaluate the behavior of high MgO and normal Samarco pellets in the blast furnace operation. Additives such as dolomitic hydrated lime, dunite and magnesite were used for increasing pellet MgO content. The test results showed that pellets produced with high MgO content are similar in quality to normal Samarco Pellets.

Jan 1, 1991

By Marc. A. Meyers

The analysis of the phenomena involved in the determination of the compressive strength of iron-ore agglomerates leads to the identification of the important parameters. It is shown mathematically that the pellet rupture strength is proportional to the cross-sectional area. Fracture is initiated at the center of the pellets by the tensile stresses developed by the compressive loads normally to the compression axis. The variation in strength between individual pellets of identical composition and subjected to identical treatments is due to internal voids of varying sizes, that act as stress-concentration sites. Two novel testing procedures are proposed. The first consists of testing the pellets between two plates having three steel spheres each. This configuration simulates much better the environment actually encountered by the pellets. The second procedure consists of a thick-walled cylinder in which a piston penetrates; a large group of pellets is tested simultaneously, as the stress versus strain plot is being recorded. This latter test presents significant advantages over the conventional testing procedure; the main one is that one single test is sufficient to characterize the mechanical response of the pellets.

Jan 1, 1981

By W. S. Versluis, G. W. R. Kuzyk

Atomic Energy of Canada, Ltd. (AECL) is constructing an Underground Research Laboratory (URL), a major component of-the Canadian Nuclear Fuel Waste Management Program. In July 1988. AECL and the US Department of Energy commenced a cooperative research program that included extending the URL shaft by 190 m (623 ft) to the 443-m (1,453 ft) depth. The shaft extension, 4.6-m- diam (15-ft-diam), was excavated by full-face blasting using a burn cut. A Galloway stage accommodated the research activities and the sinking contractor's requirements. Blast designs incorporated controlled blasting techniques to minimize blast-induced damage on the shaft walls. The full-face method has been very effective, with 3.5-m (11.5-ft) rounds being advanced.

Jan 1, 1990

By J. L. Mehaffey

A variety of chemicals offered by Armak were evaluated as dewatering aids for aqueous slurries of silica sand, sparsand and feldspar; an established commercial dewatering aid was used as a control. A number of Armak's potential dewatering aids yielded lower moisture retention values than did the commercial product on all of the mineral samples. In addition to the chemical dewatering evaluations, some of the mechanisms involved in the removal of water from these mineral samples were examined.

Jan 1, 1983

"The Ohio River Bridge East End Crossing Tunnel requires a 75-year service life of its cast-in-place reinforced concrete lining. This twin-tube 3-lane (each tube) highway tunnel is about 55-ft wide and 30-ft high. Since unified tunnel service life prediction methodology does not exist in the US, challenges occurred during the design-build phase of this project. These challenges include the methodologies in determining the reinforced concrete’s degradation mode, the lining’s surface chloride concentration level, the reinforcing steel’s critical chloride threshold value for corrosion, how to verify the concrete’s diffusion coefficient, and the durability impact from concrete crack width. This paper presents a methodology in verifying the proposed concrete mix can achieve the service life requirements. This methodology can be adopted for service life prediction for future tunnels to be built in the US. INTRODUCTION The Ohio River Bridge East End Crossing (ORBEE) Tunnel is part of a Public Private Partnership project, which connects transportation network between Louisville, Kentucky and southern Indiana. Located in Louisville, Kentucky, the twin-tube highway tunnel provides northbound and southbound lanes of the Kentucky approach to a new bridge across the Ohio River. Tunnel lengths are approximately 1,675-ft and 1,685 for the northbound tube and the southbound tube, respectively. Connected by two cross-passages, both tubes have a roadway width of 40-ft, for 3-lane traffic, and a vertical clearance of 26.5-ft.The tunnel was constructed by drill and blast method with shotcrete and rock dowels as initial ground supports. The final tunnel lining system includes: •,Nominal 16” cast-in-place reinforced concrete lining, with 2” and 3” concrete covers over reinforcing steel for its extrados and intrados, respectively. •,20” cast-in-place reinforced concrete invert slab, with 4” and 3” concrete covers over reinforcing steel on its top face and bottom face, respectively. •,PVC waterproofing system around tunnel perimeter, excluding invert slab. •,Perforated PVC groundwater collection pipes on both sides of the tubes and one below the invert slab of each tube."

Jan 1, 2016

By Harlan L. Kebel

Gypsum, the dihydrate form of calcium sulfate, has a history of usefulness to man dating back several thousand years, and a worldwide industry has been built on the mining and processing of this versatile industrial mineral. However, anhydrite, the other prin¬cipal calcium sulfate mineral, has very limited use, so much so that separate statistics for it are not always kept, but are usually included with those for gypsum. Although often found in close association, the two minerals have important chemical differences in that anhydrite is the anhy¬drous form of calcium sulfate (CaSO4) whereas gypsum is the dihydrate (CaSo4.2H20). These two molecules of combined water result in significant differences in hardness, density, and solubility of the two minerals. Of most importance, however, is the difference in thermal properties wherein gypsum, upon the application of a modest amount of heat, can be converted to the hemihydrate of calcium sulfate (CaSO4 '21H20) or plaster of paris, an intermediate product upon which is based over 90% of the value of all calcium sulfate end products. Anhydrite, on the other hand, is inert at these temperatures and its uses have been limited to only those few cases where calcium sulfate in the anhydrous form may have an advan¬tage. The earliest known use of gypsum plaster dates back some 5000 years to the time of the Pharaohs of Egypt who had discovered that gypsum rock, when exposed to fire, broke down into a powder which, when mixed with water, would form a putty that could be plastered on a rough mud brick or stone wall to make a smooth finish. It was used down through the centuries in a limited way for ornamental purposes, but did not achieve wide acceptance because of the quick (25 to 30 min) setting or hardening time which made it difficult to use. The first real understanding of gypsum chemistry was developed in France about 1755, and the gradual growth of its present utilization dates from that time. In the United States, the first utilization of gypsum was to grind it to a fine material for use as a soil conditioner at about the time of the Revolutionary War, and the term land plaster for ground gypsum was coined and has remained in use. Another cementitious material-lime or calcium oxide-had become the usual plastering material, but by about 1870 a method for retarding the set of gypsum plaster was discovered; today it has almost completely replaced lime as a plastering material. In recent years, gypsum products sold in the United States have reached a total valuation of approximately $2 Gpy as illustrated in [Table 1].

Jan 1, 1994

By Prescott Greene

AVAILABLE MACHINES Machines discussed in this section include only rubber tire mounted kerf cutting machines of a self¬propelled electrically powered design. Such machines handle bars up to 4.6 m (15 ft) in length, cutting kerfs of from 115 to 191 mm (4.5 to 7.5 in.). The basic design concept of all machines currently in production is very similar. The chassis features dual driving wheels on the cutter-bar end, fixed directly to the main frame. The steering wheels on the outby end of the frame are articulated in some manner to keep all four wheels on the floor over uneven bottom. Machine power for tramming, and all other functions except powering the cutting chain, is furnished from a pump motor that drives the specific pump or pumps required by a given machine. The cutter chain is driven through a mechanical drive train from a separate electric motor having no duty other than driving the chain. The general arrangement of a cutting machine is shown in Fig. 1; two types of machines, with their specifications are shown in Figs. 2 through 5. A hydraulically powered cable normally is included to eliminate the need for manual cable handling and make this a one-man machine. A bug duster, though optional, is needed for most applications. The bug duster is an hydraulically driven scroll conveyor located directly behind the cutter chain drive sprocket. Its function is to move the cuttings away from the sprocket to prevent them from packing up in this area and consuming a lot of machine power to further pulverize them. Available machines vary from models 610 mm (24 in.) high that can cut horizontally only from 203 mm (8 in.) below ground line to 229 mm (9 in.) above, to machines 1143 mm (45 in.) high that can cut in any plane from 178 mm (7 in.) below the ground line to 3.7 m (12 ft) above it. Most currently manufactured machines fall in the 17 200 to 20 400 kg (38,000 to 45,000 lb) weight range, but can be dis¬assembled for underground installation where weight and size are a problem. Maximum teardown results in all pieces having a weight of 5400 kg (12,000 lb) or less and a size allowing passage through a 1.2 x 2.1-m (4x7-ft) opening. Further reduction in either size or weight of the parts becomes a serious problem. Machines currently being manufactured are avail¬able for use with power supplies of 250 v dc; 500 v dc; 440, 550, or 950 v ac (60 Hz). Also available are machines for use on 415, 500, and 950 v 50 Hz. De¬signs to allow operation on other voltages of either 50 or 60 Hz can be made available without any serious problems. As of September 1977, a typical medium-seam ma¬chine without the extra options needed for unusual conditions, but fully equipped to operate, was selling for about $185,000. CAPABILITIES Materials That Can Be Cut The problem of deciding before a machine is put on the job whether it can work effectively is an old one that has never been completely solved and probably

Jan 1, 1982

By M. Canty

An innovative biological treatment system designed to detoxify cyanide and nitrate and immobilize metals from cyanide leach operations is described. A pilot-plant demonstration was conducted to detoxify cyanide and immobilize several metals from a process stream at the McCoy/Cove Mine. Testing was performed under the EPA's Mine Waste Technology and Superfund Innovative Technology Evaluation Demonstration Programs. This technology was successful in detoxifying cyanide and effective in removing metals. The pH was consistently neutralized and nitrates were successfully removed. Results show that biological treatment can offer an innovative, cost-effective alternative for the treatment of mining wastewaters.

Jan 1, 1999

By Daniel R. Stewart, Ralph R. Sacrison

The function of the geological engineer is to assist in mine planning and operations by collecting, interpreting, and applying geologic data to the solution of engineering problems. The geologist supports this effort by collecting additional geologic information specifically useful to the engineer. This use of geologic information reinforces the value of mine geology to the mining process beyond the traditional role of orebody definition. Work discussed includes: evaluation of caving strategies at the Climax and Henderson mines, support definition and slope stability at the Climax mine, and some uses of geology in cavability estimation for the Mount Emmons project.

Jan 1, 1992

By Levent Ozdemir

An extensive study involving laboratory testing and computer modeling has been performed to assess the technical and economic feasibility of utilizing the recently developed minidisc cutters on roadheaders for hard rock mining. The results show that heavy duty roadheaders fitted with minidiscs can excavate hard rock formations at acceptable production rates and cutter costs. This paper presents and discusses the results of this study together with the ongoing developmental efforts of this technology, which include laboratory testing of a roadheader cutting drum with minidiscs and full scale field testing of a machine in hard rock

Jan 1, 1995

By M. J. McPherson, P. Mousset-Jones, G. Danko, F. Calizaya, K. You

The friction factor is one of the more difficult parameters to determine in ventilation planning. In practice, this can be estimated from published factors such as those of McElroy. The problem with this approach is that the selection requires some judgement, and the estimated values offer no more than guideline accuracy. This study, examines the effects of four factors on the coefficient of friction for a simulated mine airway. The factors are: airway cross-section, asperity height, flow direction, and cross-cut spacing. The study includes the modeling of a mine airway and the evaluation of the results from 13 experiments on flows of air over rough surfaces. The model, physically represented by a wind tunnel, includes a rough surface section which can be modified to simulate mine airways of various shape and asperity height. Most of the experiments were performed under controlled flow conditions during which the Reynolds number was varied between 50,000 and 300,0000. Based on this study, the friction factor for a mine opening was found to depend not only on the size and shape of the surface asperities but is also affected by the orientation of them in relation to the flow direction.

Jan 1, 1991

By C. O. Brawner

Geotechnical theory is reasonably well developed to evaluate the stability of rock slopes for surface mining projects. It is recognized widely that structural geology, groundwater pressures and seepage, and blasting are key factors that influence the stability of such slopes. However, our capabilities to model the structural geology, to determine rock strength along discontinuities and to model groundwater pressures and profiles are still very approximate. Plus, practical experience of the rock mechanics engineer is one of the most important inputs to the design of open pit mine slopes. To emphasize the use of practical experience, a number of case examples are reviewed here to illustrate key factors that must be evaluated. These case examples comprise a continuation of other examples presented in the Jackling lecture to the SME in 1986 by the author (Brawner, 1986). Example no. 1 In situations where the orientation of geologic discontinuities will not influence rock slope stability, extremely steep slopes can be developed, providing blasting and groundwater are controlled adequately. An excellent example of this condition is the Republic Pit of Cleveland Cliffs in Michigan. The rock slope in Fig. 1 isover400fthigh with a face angle of approximately 80". The rock is hard and massive, and blasting was carefully controlled. The original design of this slope was at45", a standard design angle at that time. The competency of the rock and the lack of critical geologic structure subsequently was recognized, and the much steeper slope angle was developed successfully. The rock proved to be so competent and the slope sufficiently stable that an underground crusher station was developed with entrance and exit tunnels excavated at the toe of the steep wall.

Jan 1, 1991

By J. D. Miller

Contact time during bubble/particle collision is calculated by taking into considera¬tion the effect of bubble and particle motion, buoyant force, bubble size, and particle size and specific gravity density for different cases of collision. From this motion analysis approach for the prediction of contact times and from bubble attachment-time measurements,, fundamental aspects of flotation such as flotability, kinetics, and separation can be explained and are discussed with respect to the effects of bubble/particle motion, bubble size, particle size, and attachment time.

Jan 1, 1987

By K. B. C. Brady, B. E. Scheetz, J. E. Cuddeback, T. W. Bergstresser, W. A. Telliard, S. C. Parsons, R. J. Hornberger

Two weathering procedures are being developed by the Acid Drainage Technology Initiative in cooperation with federal agencies(OSM and EPA). Objects are to: (1) standardize existing humidity cell and leaching column procedures; (2) improve test methods by maintaining a carbon dioxide enriched environment needed to optimize carbonate mineral dissolution, and quantifying particle size variables to evaluate reaction kinetics, and (3) provide flexibility in test method implementation consistent with EPA guidelines for Performance-Based Measurement Systems. Preliminary results indicate the CO2enriched leaching environments produce alkalinities that are similar to field observations and greater than the tests run under atmospheric PCO2. Leaching columns produce higher alkalinity than humidity cells.

Jan 1, 2003

The exploitation of mineral deposits for economical recovery of the contained minerals has many aspects differing from other industrial or manufacturing operations. However, generally accepted principles of good organization and management applicable to industrial plants are similarly effective for mineral processing plants. A more detailed coverage of organizational structures and management techniques than is possible in this section can be obtained from many good books devoted wholly to these subjects. A few of the more readily available examples are included in the general references at the beginning of this section. The field of mineral processing encompass a wide variety of minerals, processes, flowsheets, equipment, and end products. Mineral deposits, mines, and related beneficiation plants are found in all parts of the globe, often in remote locations with no nearby support for supplies and maintenance. Available labor is frequently unskilled, sometimes primitive, and often untrained without machine and hand tools or heavy equipment experience. Such situations call for well- planned and conducted training programs covering the full range of mining-type job skills. Climates can range from arctic to tropical and from arid to extremes of rain or snow, and the mine and plant sites can be almost anywhere. However, it is often possible and sometimes necessary for

Jan 1, 1985

By Howard M. Wells

Portfolio theory and the Capital Asset Pricing Model (Modigliani and Pogue, 1974) provides an investment decision rationale which takes account of the benefits of diversification in reducing effective risk, but this theory does not consider the financial capability of the firm to survive large losses if they should occur. The LL-curve theory (Wells, 1976) takes the latter consideration into account, but it does not provide for the effects of diversification. This paper pro- poses a general theory to account for both diversification and the financial capacity of the firm to underwrite the investment risks.

Jan 1, 1983

By T. Chandler, R. Buchan, J. H. Blowes, E. G. Haldeman

The regional geological setting and nature of the serpentinized ultramafic rocks are described. It is postulated that lateritization started in Miocene time. Repeated uplifts led to at least four physiographic cycles and to the development of a mature lateritic soil profile. Complete profiles are subdivided from top to bottom as follows: Zone A - chocolate-brown limonite; Zone B - ochre-brown limonite; Zone C - soft serpentine; Zone D - hard serpentine; Zone E - serpentinized peridotite; Zone F - ultramafic rock. Zones A and F rarely attain ore grade. Canga is conspicuously absent. Rocky ore of Zones D and E amounts to 40%, limonite ore of Zone B to 25% of total ore reserves. Nickeliferous serpentine is the major crystalline phase in Zone C. In this zone and deeper, crystalline quartz occurs, particularly in fracture zones where nickeliferous cryptocrystalline quartz is of ten accompanied by garnierite.

Jan 1, 1979

By Reinhard Gertl, Soroush Dabiri, Juan-Carlos de Rueda

The Tunnel of Guillermo Gaviria Echeverri, spanning 6.05 miles, will be Latin America’s longest road tunnel, is currently under construction in Colombia’s Antioquia Department with a single bidirectional tube connected to a parallel rescue tube through multiple cross-passages. The study faces challenges in implementing the prescriptive semitransversal ventilation system due to design restrictions. Different ventilation concepts are eplored to nd the most suitable system for regular operation and re scenarios. A quantitative ris assessment evaluates each alternative system and identies the longitudinal ventilation system, accompanied by ris mitigation measures, as the safest choice, since it surpasses the prescribed semitransversal ventilation concept.

Jun 23, 2024

By Jeff Reid, Mohamed Maghari, Nicholas Joens

The Burnaby Mountain Tunnel was an integral part of the Trans Mountain Expansion Project. General Contractor, Kiewit Ledcor TMEP Partnership (KLTP), contracted with McNally Construction to build an underground tunnel between the Burnaby and Westridge Marine terminals under Burnaby Mountain. The pipeline was constructed within a 2.6-kilometre tunnel, eliminating the need to run the pipeline over the mountain and minimizing community impacts. The complexities of this Project led to multiple innovations, including the design of a Tunnel Boring Machine (TBM) capable of excavating through mixed-faced conditions concurrently thus allowing the Project team to complete the tunnel with limited geotechnical information.

Jun 23, 2024