Search Documents

By Richard C. Enochs

In order to clearly understand our process control system it is necessary to briefly discuss the various process control systems that were considered and why we chose our particular configuration. We considered Analog Systems, Computer Supervisory Systems, Computer Setpoint Systems, Direct Digital Systems and Direct Digital with Backup Systems. Our concept of these systems is illustrated in Figure 1 through Figure 5. We chose Direct Digital Control with Manual Backup because it had the greatest flexibility, ease of implementation and cost no more than a pure Analog Control System for one control concept. There would be no increase for a Direct Digital Control with Manual Backup System if the control concept were changed, while there could be considerable additional cost with an Analog System, if the control concept were changed.

Jan 1, 1975

By Muhammad I. Kabir

A new minitest of in situ uranium leaching processes at reservoir conditions is proposed. The test which consists of a single observation/ production well and two observation wells is designed to permit the evaluation of both restoration and leaching parameters. It is shown that by using a straight forward history matching procedure, sometimes called a type curve analysis, both the rate of leaching and the ultimate uranium recovery can be evaluated based on the results of the test. Type curves are presented for the case in which the reaction rate is kinetically controlled and there are no other minerals competing for oxidant. Other situations can be approached using the same techniques as those presented here.

Jan 1, 1981

By Jerry R. Riding

Metallurgical process methods have seen dramatic improvement over the past fifty years. As these improvements have come about, more and more emphasis has been placed on obtaining accurate and rapid analysis of the metallurgical processes. Well-defined conventional laboratory analysis procedures which have proven to be reliable were developed early in the mineral industry's history; however, these conventional procedures, which have not changed appreciably in fifty years, have the serious drawback that they are too slow to be of appreciable value in automatic control of the processes. For example, the assay results normally become available to a mill operator from eight to twenty-four hours after a sample is taken. Since the desired mineral separation can only be made while the minerals are in the flotation circuit, conventional assay results provide information similar to postmortem reports. Consequently, using conventional procedures, the mill is operated with information from an earlier period of time, which may not reflect current conditions. In recent years there has been a steady increase in the volume of required samples. At the same time, labor, material, and overhead costs have continued to rise causing the cost per assay to reach an alarming level. This rising cost per assay, plus the increasing demand for rapid analysis necessary for control, has caused the mining and metal processing industries to look toward other techniques to solve these problems As a result, X-ray fluorescence which can provide on-stream analysis necessary for control, as well as perform numerous laboratory assays at lower cost and at a much greater speed than conventional methods, has gained wide-spread attention. In addition, multichannel X-ray fluorescent instruments are now available which have been perfected to the point where the analysis of the most important chemical constituents is available within one minute after a sample is presented to the X-ray analyzer. Because of these obvious advantages, extensive use is being made today of X-ray analysis in the mining industry to analyze slags, ores, and mineral content of rocks. The results are used to make quick decisions for both mining and beneficiation of metals. For example, X-ray systems which provide rapid on-stream analysis of the slurries at desired points Fn metallurgical processes have recently been developed. The successful application of these systems has moved the milling process a step closer to fully automatic control.

Jan 1, 1969

By A. Taghavi, I. Hassan, A. Solecki

"The Eglinton Crosstown Light Rail (LRT) Project is part of an $8.4 billion investment to expand transit in the Toronto, Canada area and is the largest transit project initiated in Province’s history. Settlement control and impact to over 1400 adjacent structures due to tunnelling was identified early as a critical project risk. The ground conditions along the 10km tunnel alignment consist of water bearing soft ground deposits (clays, sands, silts) which required careful analysis and control during design and construction. This paper will describe the process used to analyze settlements along the numerous of adjacent structures and evaluate achieved settlement results to those used during design. The paper will demonstrate that with the appropriate design specifications, selection of modernized EPB machines, and contractor performance, settlement can be maintained well below typical industry (volume loss) standards, expanding the application and suitability of soft ground tunnelling in sensitive settlement areas. INTRODUCTION The Eglinton Crosstown Light Rail Transit (LRT) Project is part of an $8.4 billion (2010$ CND) investment from the Ontario provincial government to expand transit in the Toronto, Canada area. The project is being developed by Metrolinx, an agency of the Government of Ontario to provide 19 kilometers of dedicated LRT service connecting the City of Toronto from the west to east along Eglinton Avenue. Upon completion in the year 2020, the Crosstown will be the first LRT constructed in Toronto. It will link regional and local transit, cut travel time along the route by half and provide over a thousand jobs during construction."

Jan 1, 2016

By J. J. Sammarco

Computer-aided control of a mining machine pl aces its operator in a safe, remote location, thus reducing health and safety risks, Sensing systems that provide machine position (xy coordinate) and heading (yaw), are extremely useful in aiding remote positioning of mining machines. The U. S. Bureau of Mines has developed two sensing systems for position and heading information: A scanning laser system based on the Lasernet sensor and a mechanical position and heading system based on linear-position transducers. The Bureau is also investigating a system from Honeywell, the modular azimuth and positioning system that employs ring-laser gyroscopes. This paper presents a brief background and status of these sensing systems as applied to the remote positioning tasks of a continuous mining machine. Included are field test results of each system operating in a room-and-pillar research section at a cooperating mine in West Virginia.

Jan 1, 1992

By Frank W. Schmechel

The subsidence monitoring program at the Old Ben No. 24 Mine was planned in 1976 as part of the on- going demonstration of longwall mining. The construction and installation of the network of surface subsidence monuments was started in Play of 1976 and completed four weeks later after which an initial reference survey was made of all surface monuments. Mining of the first longwall panel started in September of 1976 and was completed in May of 1977. Mining of the second panel started in August of 1977 and is continuing at this time. The Automatic Data Acquisition System (ADAS), which is the subject of this paper, was installed over the second panel on March 29, 1978 near the panel center (Figure 1) and approximately 104 meters (370 feet) in front of the face position at that time. Mine No. 24 is located approximately 5 kilometers (3 miles) Northwest of Benton, Franklin County, Illinois. Coal is being mined from the Illinois (Herrin) No. 6 seam which is at a depth of about 189 meters (620 feet) at the site. The Herrin No. 6 is up to 2.7 meters (9 feet) thick in the mine but a constant thickness of 2.1 meters (7 feet) is being mined by the demonstration longwall with both roof and floor coal being left for stability. Although the seam is flat laying at the mine, it dips north- ward regionally. Topographically, the surface over the demonstration panels is essentially flat and low laying with several areas of standing water. The Rend Lake Dam (United States Army Corps of Engineers) is about 305 meters (1000 feet) north of the demonstration site.

Jan 1, 1979

By S. Dixon

The use of warm (40-50°C) solution for the selective elution (pre-strip) of copper cyanide from gold and silver cyanides adsorbed on activated carbon was found to elute +90% of the adsorbed copper compared to the use of ambient (20°C) solution eluting 50-70% of the adsorbed copper. The warm solution pre-strip elution did have higher co-elution of gold (1-4%) and silver (10-18%) with the copper. The use of ambient solution pre-strip elution co-eluted less gold (0.2%) and silver (2%).

Mar 2, 2022

By Stephen Utter

This report summarizes the results of preliminary investigations concerning the influence of block caving mining upon adjacent mine openings and discusses possible methods for reducing critical rock pressures and damage to these openings. These investigations are one part of a general study of the rock mechanics of block caving by the Denver Mining Research Center of the Federal Bureau of Mines. The purpose of this part of the study Is to obtain an estimate of the stress concentrations around mine openings adjacent to block caving stopes for use in developing better designed openings and improving mining methods. When mine openings such as slusher drifts, grizzly drifts, and haulage drifts are damaged by rock pressures induced by block caving mining, the mining cost increases, mine production decreases, and ore recovery may be consider- ably lessened. Methods of mining that result in lower rock pressures and methods of design that enable mine openings to withstand these pressures are desirable. The development of these methods, in turn, requires a fuller understanding of the following: The stres concentrations around the mine openings and the changes in stress induced by adjacent mining; the physical properties, such as the compressive strength and modulus of elasticity of the rock surrounding the openings; and the support supplied by the concrete lining, timber sets, or other types of supports used in the openings.

Jan 1, 1962

By Walter M. Chapman

The National Lead Company operates its MacI tyre Development at Tahawus, New York for the production of ilmenite and. magnetite. The heavy ore of titanium and iron is mined from the open pit mine at an average rate of 7,000 tons per day, and the development waste is removed at an average rate of 10,000 tons per day. The mine working benches are spaced, at 35-foot vertical intervals, and 6 ½ inch blast holes are drilled 39-feet deep with 18-foot burden and spacing by down-the-hole drills. Waste is loaded with a 6 yeard shovel and ore with 2 ½ yard shovels into 22-ton rear dump trucks. A good account of the history of MacIntyre drilling and. blasting was presented to this assembly two years ago, by F. R. Jones. (1) Most of the blasting since the start of the mine in 1941 was done with 90% gelatin dynamite until 1955, when relatively insensitive canned blasting agents were adopted.. In 1956, 9-inch blast holes drilled with down-the-hole drills. In 1956, also, the first experimental trials of prilled ammonium nitrate fertilizer and fuel oil (hereafter called fertilizer) was made following the lead of Cleveland-Cliffs operations in the Hibbing district. Since that trial did not, as some local skeptics predicted, make grass grown on the bluff, but resulted in a well-broken shot, further tests were conducted in dry holes. I Observations of those tests indicated that the fertilizer did its share of the work. If anything, it produced better fragmentation than the normal load di in neighboring wet holes.

Jan 1, 1958

By Robert Blair, David L. Fey, Stanley E. Church

Determination of the pre-mining geochemical baseline in bed sediments in watersheds impacted by historical mining activity is important in establishing watershed restoration goals. We have developed methods to solve this problem in the Animas River watershed, southwestern Colorado, using geomorphologic mapping to identify terraces that contain pre-mining sediments. Following a systematic evaluation of possible sites, we collected samples of pre-mining sediments in gravel deposits from 21 sites throughout the watershed. Geochemical analysis of individual layers has produced a chemical stratigraphy that can be tied to the historical record through geochronological and dendochronological studies. Analysis of geochemical data, when coupled with the historical record, clearly shows that there has been a major impact on the geochemistry in bed sediments in the active stream channel by past mining activities. Historical mining has resulted in a substantial increase in metals in the very fine sand to clay-sized component of the bed sediment of the upper Animas River, and Cement and Mineral Creeks, which are the major tributaries of the Animas River. Enrichment factors for metals in modem bed sediments, relative to the pre-mining sediments, range from 1 to 6 for arsenic, 1 to more than 10 for cadmium, 1 to about 15 for copper, 1 to more than 25 for lead, 1 to more than 10 for silver, and 1.6 to more than 12 for zinc. The pre-mining bed sediment geochemical baseline is high relative to average crustal abundance values of many metals. The Animas River watershed above Silverton, Colorado would be readily identified as a highly mineralized area suitable for mineral exploration if it were not disturbed by mining.

Jan 1, 2000

By Leon D. Keller

Hydraulic concentration of minerals has been practiced for a good many years. Until recently, however, the practice has been limited to a multiplicity of small pockets and relatively low tonnages and flows. The adaptation of the SiphonSizer to the concentration and classification of magnetite has changed this concept. Some fifty commercial units are currently in operation on magnetite, varying in size from 16 ft diameter circular unit to a 25 ft by 100 ft rectangular unit. Additional units up to 38 ft diameter are under construction. Depending upon the application in the flowsheet, upgrading-varies from 0.75% to 14% Fe in a single stage. To those not familiar with taconite processing, the importance of the struggle to economically remove as much silica as possible may not be fully appreciated. These figures pertaining only to transportation may be thought-provoking. If a 10,000,000 ton per year plant could reduce the silica content of their concentrate by 17, a savings in boat freight alone would amount to 100,000 tons at $2.00 per ton annually.

Jan 1, 1963

By J. L. Workman

The stability of spoil and highwall slopes are important to successful strip mining. This paper discusses soil parameters of importance in stability analysis. The common mechanisms of spoil failure are discussed. Modes of highwall failure are also outlined. The importance of water to stability is presented. Dragline mining methods most suited to creating spoil and highwall profiles that address stability needs are provided. It is concluded that groundwater and surface runoff must be well controlled, and that it will often be necessary to modify spoil and highwall configurations to achieve a stable overall slope angle.

Jan 1, 1996

By Robert J. Willard

In its search for additional ways to increase understanding of rock behavior, the Twin Cities Mining Research Center has turned to the scanning electron microscope, an instrument rapidly finding application in research concerned with surfaces of materials. Since features indicative of the manner in which rocks fail may be recorded on the surfaces of fragments as disintegration proceeds, this microscope might be used as a tool for seeking and mapping these minute features. In pursuit of such features, we chose to scan a portion of the fracture surface from a quartzite disk compressively loaded to failure between two pins centered along the disk's axis. The resultant fracture appeared as a rough, diametric plane, and the fracture surface near one of the loading points was scanned with the microscope.

Jan 1, 1969

By Kim A. Lapakko, William W. III White

The ASTM standard method D 5744-96 was developed to provide a well-defined kinetic test protocol, conducted under controlled reaction conditions, with the intent of generating reproducible results. A preliminary indication of the repeatability of a simplified alternative method (MN DNR method) was assessed and results from the MN DNR method were compared to those from the ASTM method. To provide an indication of repeatability, six samples from three different rock types were subjected to dissolution testing for periods of 20 to 68 weeks. Drainage pH values at the end of the tests were within 0.5 units in all cases and within 0.05 units in four cases. The percent difference from the mean for overall sulfate rates from paired cells ranged from 0.04 to 1756, with a median of 6.3%. Nine samples from four rock types were subjected to both MN DNR and ASTM tests for periods of 20 to 132 weeks. The difference in final drainage pH values forsix of the samples was less than 0.1 unit, and these values were less than pH 3.65 or greater than pH 8.0. The final drainage pH difference for the last three samples ranged from 0.15 to 0.4, and these values were ill the pH range of 6.2 to 7.2. The sulfate release rates for the periods of record for the MN DNR method were 70 to 150% of those for the ASTM method, with a median value of 110%. Sulfate and calcium release from the two methods was not substantially different. The MN DNR method typically produced higher magnesium release.

Jan 1, 2000

A general form of pore pressure in a saturated porous medium, which is subject to external forces it has the pressurization of a borehole in hydraulic fracturing, is derived. The pore pressure consists of two parts: the preexisting initial pore pressure and the pressure induced by fluid flow due to the pressure difference caused by pressurizing the borehole The initial pore pressure associates with the effective stresses in the stress, fields of crustal stresses and a thick hollow cylinder subjected to internal and external pressures. The pure pressure weaned by fluid flow is implied in Biot's (1941) constitutive equation for three-dimensional consolidation and proved to be the exact effective pore pressure (Nur and Byerlee, 1971). Using this general form of pore pressure, a general poroelastic model for hydraulic-fracturing breakdown (fracture-initiation) pressure was derived. This model was validated by laboratory experimental results on Indiana limestone. Three sets of tests were conducted under the conditions of preexisting pore pressures of 6, 21 and 28 MPa, respectively. The equal horizontal (confining) pressures applied in the tests ranged from 6 to 60 MPa. Hainison and Fairhurst's (1967) model appear to be applicable to rocks having microcracks or flows. Experimental results of fracture reopening pressures on Indiana limestone supported this assertion. The test results also demonstrated that, when the pressure difference between the confining and the initial pore pressure grows larger than 14 to 21 MPa, the breakdown pressures agree well with the general poroelastic model developed in this paper. This indicates that the developed model will be superior when hydrofacturing stress measurements are conducted at great depth.

Jan 1, 1997

By J. D. Morgan

The US economy grew steadily in 1989, reaching an annual rate of $5.3 trillion in the last quarter (US trillion=1012 ). The value of domestically processed, mineral-based materials rose 5% to $315 billion (US billion=109). The value of metals produced from US ores rose 14% to $11.6 billion, while industrial minerals rose 2% to $20.2 billion. Recycled scrap was valued at $10 billion. Increasing economic activity stimulated metal prices. Yearly lows and highs were $2.31 and $3.56/kg ($1.05 and $1.62 per lb) for copper, $1.58 and $2.57/kg (72 and $1.17 per lb) for aluminum, 77 and 97 cents/kg (35 cents and 44 cents per lb) for lead, and $1.58 and $2.09/kg (72 cents and 95 cents per lb) for zinc. Many mining and metal companies reported reasonable profits. Consumer demand strongly affects mining because the US economy is saturated with long-lived products. Consumer, mortgage, and Federal debt continued to rise. 250 million US citizens already possess 172 million licensed motor vehicles and 100 million dwelling units. New car production fell 4% to 6.8 million units, while truck and bus production fell 1 % to four million units. New housing starts fell 9% to 1.4 million units. Imports supplied a significant proportion of total US consumption of several important mineral materials. Imports of crude and refined petroleum costing $50 billion exceeded domestic crude oil production. President Bush expressed "strong concerns about this country becoming further dependent on foreign oil." And the Department of Energy held a series of hearings around the country to develop ideas for a "national energy strategy."

Jan 1, 1990

By E. J. Sullivan

This study seeks to define the mechanism of oxyanion sorption onto surfactant-modified zeolites. Zeolites which have been treated with hexadecyltrimethylammonium bromide (HDTMA) surfactant to produce a hydrophobic surface are capable of sorbing both organic compounds as well as oxyanions such as chromate, selenate, and sulfate. Simple ion exchange and charge-balancing mechanisms do not fully explain this unusual phenomenon. The sorption of HDTMA surfactant appears to be partly ion exchange and partly sorption to non-ion-exchangeable sites. Sorption of chromate is a simple exchange mechanism with bromide, which co-adsorbs with HDTMA to form a surface precipitate. Information from this study will be used to design on-site and in situ treatment systems for contaminated water, such as filter beds and permeable barriers.

Jan 1, 1995

By X. Cheng

A series of batch flotation tests was performed on chalcopyrite-quartzite, pyrrhotite-quartzite, and on chalcopyrite-pyrrhotite-quartzite mixtures. Pulp potential measurements in the flotation tests of single sulfide minerals indicated that each sulfide mineral had its own optimum potential range for flotation. When these results were used to select the potential ranges for the separation of the two minerals from their mixture, their flotation responses changed and the selectivity of separation was adversely affected. A possible mechanism involving surface alteration through galvanic interaction is discussed. A method to improve the selectivity of flotation separation was proposed.

Jan 1, 1992

By T. J. Lyman, M. J. Robison, W. A. Ruemmele

INTRODUCTION The first phase of the Los Angeles Metro Rail Project consists of 7.1 km (4.4 miles) of subway and stations running through downtown Los Angeles from Union Station to MacArthur Park. Contract A171, the Wilshire/Alvarado Line, involves tunnel construction beneath 7th/Street from the 7th/Flower Station to the Wilshire/Alvarado Station. The project consists of the excavation and lininig of 3000 m (9900 ft) of twin-bore, 6.7 m (22 ft) excavated diameter, 5.5 m (18 ft) finished diameter subway tunnels. The location of the project is shown in Figure 1. The majority of the excavation passed through weak siltstone/ claystone bedrock; although, portions of each tunnel approaching the 7th/Flower Station passed through fine-grained alluvium. Both tunnels were excavated with a digger shield. The project also included the excavation and lining of 6 cross passages, 2 communication rooms and a sump, all at tunnel grade between the two bores. A program of geotechnical instrumentation and building monitoring was performed to detect and document the response of the ground and adjacent structures and facilities to tunnel excavation. The instrumentation program was also intended to provide information that would permit implementation of remedial measures, when and as required, to prevent damage to structures, facilities and utilities along the tunnel alignment. The purpose of this paper is to discuss the ground response to tunneling on Los Angeles Metro Rail Contract A171. This paper presents a description of the tunnel project, the excavation and support method used in construction, the subsurface geology, and

Jan 1, 1989

By H. W. Breathitt

World demand for phosphate rock has increased significantly in the past fifteen years. Prior to the early 1960's, most of the world production was obtained from Florida, North Africa, and Kola. As the 1960's arrived, new mines in North Florida and Eastern North Carolina, as well as expanded production in the Western United States, .increased domestic production. Many new mines overseas have also become significant. This includes countries such as Senegal, Togo, Israel, Spanish Sahara, and Jordan. Limited production, often as by-products, has been noted in South Africa, Brazil, and other countries. In recent years, and even recent months, we have learned of many new areas being considered as potential sources of phosphate rock. This includes Australia, Saudi Arabia, Mexico, Colombia, and Brazil. Many other developing countries have discoveries and are considering their new deposits, often with difficult beneficiation problems, as potential sources of phosphate. These factors all relate to expanded world, population and the demand for more fertilizer products to produce food. In this paper, four areas of the world with different types of phosphate deposits are briefly reviewed to contrast the ore beneficiation problems to Florida procedures--long considered the "standard" of the industry, at least for most of the United States' domestic production. Agrico has three large operating mines in Florida with total production capacity exceeding seven million tons per year. Here, pebble phosphate (+14 mesh material) is produced without the use of flotation, whereas all of the material finer than 14 mesh is subjected to flotation beneficiation to upgrade into high grade concentrates.

Jan 1, 1977