Search Documents

A Mark IV surface force apparatus (SF A) was used to conduct direct force measurements in dodecylamine hydrogenchloride collector solution between mica surfaces at varying pHs. It has been found that the long-range hydrophobic forces reach a maximum at pH 9.5, which also corresponds to the maxima attained by the contact angle and flotation recovery of quartz. The charge densities are comparable on both mica and quartz surfaces (0.40-0.48 run2), making it possible to draw conclusions on the flotation of quartz from the direct force measurements conducted on mica. Therefore, it may be suggested that the maximum flotation recovery of quartz m the range of pH 8.0-10.3 may be attributed to the appearance of long-range hydrophobic force, which in turn can be related to the formation of a close-packed monolayer (or hemimicelle) in the presence of neutral amines formed as a result of hydrolysis.

Jan 1, 1996

By Roger K. McLimans

Sphalerite in the ores is multi-banded. Based on color and textures, bands in samples separated by a few kilometers may be correlated. Darkness of color is directly related to iron content. Isotopic and fluid inclusion data indicate that temperatures of ore deposition were 225°C-50°C. The agreement between these two sets of data suggests that chemical and isotopic equilibrium were established. The salt content and hydrogen and oxygen isotopic compositions are similar to present-day values of oil field brines suggesting a similar mode of origin. Ore transport and deposition are not adequately explained by either chloride or bisulfide complexing. Necessarily, other mechanisms were involved.

Jan 1, 1979

By Dolf W. Fieldman

Most recently the geologic setting of the mineral deposits in the Silver Cliff district is described by William M. Sharp in ?Geologic Map of the Silver Cliff and Rosita Volcanic Centers, Custer County, Colorado?, (U. S. G. S. Map I- 1081). The discussion will relate only to the southern half of the Silver Cliff volcanic center and differences in geologic interpretation, which are largely structural, will be pointed out as they arise. Only the manganese/silver zone of the Kate Area will be discussed in detail.

Jan 1, 1980

By Mitchell Gordon

Two mineral processing facilities in North America required near terminal density slurries to perform de-bottle necking in their circuits. The installation at Barrick Goldstrike to ensure efficient oxidation conditions and throughputs in the refractory ore treating autoclaves. The Kidd Metallurgical Division unit to provide a steeper tailings slope to extend the life of the existing tailings dam. To achieve these goals, both operations selected a Supaflo "High Compression" Thickener following on site pilot plant evaluation. Commissioning and the first year of operation is reviewed. Operating data is compared with the pilot plant data. In particular, unusual doughnut formation at Goldstrike and the effect of temperature on the terminal density at Kidd Metallurgical Division are discussed.

Jan 1, 1997

By George Alan Weed

The management of safety is not only the most noble, but also the most personally and financially rewarding of all the management functions. The management of safety should result in the prevention of accidents and the elimination of human suffering and loss of life. Safety management must be the number one priority of all management's production and profit objectives. For years, safety management has been a result of mockery, charlatanism and snake oil presentations dedicated to giving a quick dog and pony show. The result has been an unacceptable record of accidents and fatalities.

Jan 1, 1981

By R. L. Grayson

Using powerful database management software, nested-field analysis and microanalysis of narratives have been made of West Virginia accident data, resulting in a new approach for targeting and prioritizing safety interventions by county, mine size, specific mine, job title, type injury, etc. and combinations of these parameters. The analyses have been useful in focusing training and discussion sessions on specific work problems, trends, conditions, and situations for targeted groups of miners. Application of the technique will be presented in this paper, along with comparisons of various mine performance measures.

Jan 1, 1997

By Roberto L. Romero

The dressing of Bolivian tin ores has been done up to the present by classical. gravity methods, taking advantage of the high specific gravity of cassiterite compared with that of the accompanying gangue. For this purpose, jigs and shaking tables are used in the treatment of the various size fractions in which the ore is classified. Bolivian ores are mainly of the vein type and, to obtain a reasonable separation, crushing and several stages of grinding are necessary during the process to substantially liberate the cassiterite from the gangue. Gravity processes for cassiterite are effective for sizes down to 200 mesh. Below this size the efficiency of the gravity methods falls off very rapidly with increasing fineness of the mineral grains. The conventional treatment for this material is desliming followed by tabling on shaking tables various other types of machines have been designed for the gravity treatment of these fine particles but they have had limited success. Bolivian ores contain an appreciable amount of minus 200 mesh material constituted by "primary fines" caning from the mine itself, and "secondary fines" originated during the crushing and grinding necessary for liberation of the difficulty in the treatment of these fine particles is one of the causes why the recovery of tin in concentrates is only of around 50% in the mines owned by Corporacidn Minera de Bolivia, the State owned enterprise. The average figure for other Bolivian mines is

Jan 1, 1971

By Robert L. Vines

"What is past is prologue" - motto of National Archives The question of past, present, and future safety performance in the coal mining industry is not merely an academic one, or one which arises from soul-searching curiosity. It is a question involving pragmatic ramifications, and the answers, or perhaps the public perception of the answers, will have a strong impact on the public policies which influence the course of meeting the Nation's future energy demands. Those of us in the coal industry are keenly aware of the significant impact of the public reaction -- in the form of the 1969 Health and Safety Act -- to -past performance of the coal industry which it found unacceptable. That Act was revolutionary -- and it was expensive. But in finding the industry's past performance unacceptable, the public also recognized its own contributory role through having enjoyed a "buyer's market" forced on a highly competitive industry. One result was to limit the industry's resources and restrict its ability for self-improvement of its safety performance. In acknowledgement of that role, the public picked up the tab for Black Lung disability incurred prior to that time.

Jan 1, 1985

By D. Tao

Reverse cationic flotation is the most widely utilized flotation method for concentrating iron ore. In this process, quartz is often floated with ether amines (R?(OCH2)3?NH2) partially neutralized with acetic acid. However, it is well known that the cationic flotation of quartz does not work well if a certain amount of slime is present in the ore slurry. To improve flotation performance, starch is often added to the flotation feed to selectively flocculate and depress the iron minerals and sodium silicate is used to disperse the silica gangue. The present study was conducted to improve the efficiency of iron ore flotation by the use of a new type of depressant for clay and iron minerals, Georgia Pacific (GP) clay binder. The GP clay binder minimizes slime adsorption on quartz and hematite particles by agglomerating clay particles to reduce their surface area. It also helps depress hematite flotation due to its unique chelating action on iron ions. The results from this study show that the GP clay binder is an effective depressant in iron ore flotation. When it was used as a substitute for corn starch, it increased concentrate grade from 60.78% to 67.67% and increased iron recovery from 71.96% to 72.90%. The combined use of GP clay binder with corn starch produced even better flotation performance, increasing iron recovery to 78.15%, while the concentrate grade remained stable at 67.08%. Keywords: Georgia Pacific clay binder, Iron ore flotation, Flotation efficiency

Jan 1, 2010

By Henry P. Ehrlinger

These are exciting times for those of us involved in the discovery, development, beneficiation, sales and end uses of industrial minerals. The known sources of traditional raw materials are rapidly being consumed or covered up with highways and urban developments. We would never knowingly cover up a source of gold, silver, diamonds, or even base metals with a shopping center, but it has been difficult to justify not locating construction atop a limestone, granite, or sand dune deposit. During the last ten or so years most of the users of significant amounts of industrial minerals have established task forces made up of geologists, mining engineers, beneficiation experts, ceramic and refractory scientists, and senior members of their purchasing departments whose duty it is to determine where the raw materials for their particular finished products will come from now and farther down the road, like 20 years from now. Likewise, these same ceramic and refractory scientists are developing new materials which require a never ending change into different raw materials and the traditional materials must be refined by selective mining, exotic beneficiation practices and expensive but necessary post-beneficiation treatments to produce minerals for commercial use that were either theoretical minerals or at best showcase specimens when most of us here today were in school studiously acquiring a vocabulary which included Calcite, Magnesite, Dolomite , Feldspar, (Labradorite had the play of colors the prof could see but which I rarely focused on) Wollastonite, Celestite, Chromite, Olivine, Barite and Lepidolite to name a few.

Jan 1, 1976

By R. W. Bartlett

High salinity geothermal brines typically contain up to several hundred parts per million of valuable heavy metals, and because of the large potential flow of geothermal brines from future power plants, metal production as a by-product could be significant A-planned 55-MW demonstration plant near Niland, California should generate enough spent brine to contain approximately $670,000 per year in gross metal values. Lawrence Livermore Laboratory estimates (1) a Salton Sea Geothermal potential of 1300 to 8700 MW, which would translate to possible yearly heavy metal values between $5,800,000 and .$l05,000,000. Since these estimates were made on a conservative basis, this geothermal reservoir is potentially a large ore deposit. The heavy metals in order of decreasing abundance in high salinity brines from the Salton Sea geothermal field are usually manganese, zinc, iron, lead, and silver. All but manganese and iron are valuable enough to be of commercial interest. Minor amounts of copper and arsenic are also present. Although heavy metal precipitates, particularly lead, have been found in scales within pipelines and obtained from steam flashing, most of the metals remain soluble during steam production; hence removal of the valuable metals from the spent brine before reinjection in ground reservoirs is indicated. Because the heavy metal concentrations are low, a very simple and inexpensive process is required. The heavy metal value in Niland brine is only ' about $1 per 1000 gallons; see Table 1. The brine composition shown in Table 1 was taken from one of the brine samples used in our study. Projected post-flash brine from a steam plant has somewhat higher Zn and Pb values, but the gross heavy metal value is still less than $2 per 1000 gallons.

Jan 1, 1980

By W. K. Tolley

The U.S. Bureau of Mines (USBM) is currently investigating the electrochemistry of mineral flotation. A significant need in this area is greater reliability of sensors. The USBM is testing electrolytic methods to clean and condition redox-sensing electrodes to improve the reliability and extend the service life of these instruments in the harsh physical and chemical environment of mineral processing slurries. A novel method for removing scale from fouled electrodes has been developed that includes anodic polarization to 1.2 V versus the Ag/AgCl reference potential, followed by brief potentiodynamic conditioning. Laboratory results show that this technique removes calcarious deposits from gold sensing electrodes and returns the electrode to useful service within approximately 10 min. Mechanical abrasion to remove the scale is thereby avoided.

Jan 1, 1994

By D. C. Torre

The need for a successful, efficient and reliable continuous face- haulage .system for use with continuous mining machines has been apparent since the first continuous miners were introduced some twenty-five years ago. Some thought and effort were given to the development of continuous haulage over the last twenty years or so. Some initial success was experienced in this area by The Long Company with a system involving bridge conveyors, as far back as the late 1950's. However, extensive success with continuous face haulage for use behind modern, high product¬ion, continuous miners escaped the industry until the early 1970's. It is true that continuous face haulage was successfully introduced into low seam mining, generally in seams ranging under 1.07 m (42") in height, in the 1960's, for use with relatively low production, low seam, auger type continuous miners. However, those available systems which have achieved success in the lower seams, where relatively low capacities are adequate, are not directly applicable for use with today's medium and high seam miners with their standard production capacity of 9.1 - 10.9 mtpm (10 - 12 tpm). Since the late 1960's and early 1970's, several machinery manufacturers, and at least two major coal companies, have devoted considerable expense, time and effort to developing truly successful continuous face haulage for use in coal seams ranging upward from 1.2 m (4') in height. Continuous face haulage equipment has been developed in the last five years employing a variety of transportation media and design concepts, including some which have received wide publicity such as those employing hydraulics, and pleated belt. The truth of the matter is, however, that the only universally applicable and widely successful continuous face haulage equipment introduced to date has been that employing a combination of bridge conveyors and mobile, self-propelled, bridge carriers, connected at the inby end to the tail of the high production continuous miner, and at the outby end attached directly to the panel conveyor (Fig. 1 & Fig. 2) or, on occasion, to a short, self-contained conveyor which, in turn, empties directly onto the panel conveyor. While these bridge type continuous haulage systems are available with both belt and chain conveyor components, the most widely applied and successful system in seams above 1.07 m (42") in height is that offered by The Long-Airdox Company. The standard unit for use with 9.1 - 10.9 mtpm (10 - 12 tpm) continuous miners is normally equipped with belt. However, they have built, and successfully applied, versions of this system employing chain conveyors, (Fig. 3), mainly for operators having extremely difficult mining conditions, including excessive amounts of water

Jan 1, 1977

By R. M. Clowes

LITHOPROBE is a collaborative, multidisciplinary research project that is providing new insights into the tectonic evolution of the North American continent through its work within 10 study areas across Canada. For the mining industry, such results provide a well-constrained regional framework and better understanding of the tectonic processes that lead to the development of ore deposits. In mining camps, seismic-reflection methods have proven effective in imaging shallow to moderately dipping lithologic contacts as well as structural features and, in some cases, have been used for the direct detection of orebodies. Here, short case histories are provided for the Abitibi greenstone belt (VMS deposits) in Quebec and the Thompson nickel belt in Manitoba.

Jan 1, 2002

By Robert J. Greaves

High-resolution seismic reflection profiling can be used to evaluate detailed struc¬tural and stratigraphic features of coal pros¬pects. Since most coal prospects are relatively shallow (less than six hundred meters deep), the vertical and lateral resolution of seismic data can be significantly improved by high sampling rates in space and time. The case study present¬ed shows the effective use of seismic data in evaluation of the Wyodak coal at a prospective coal gasification site. The data were used to map the detailed structure and thickness of the coal and to search for lateral discontinuities, such as pinchouts and. faults. An important find was a paleochannel cutting across the base of the coal seam, which was later confirmed by drilling.

Jan 1, 1983

By V. M. Torres

Arapiraca ore deposit has a mixed chalcopyritelbornite mineralogy, with a copper head grade of 0.7%. The reserve size does no allow profitable exploration by grinding/flotation. The technical feasibility of exploring the reserve by heap leaching was studied. Preliminary agitation tests indicated 85% copper recovery. To simulate heap leaching, column tests were performed. The tests included different ore types and acid addition levels. Operating at pH range 1.6-1.8, 67% copper extraction was achieved. Also, it was found an empirical correlation between the operation pH range, copper extraction and acid consumption.

Jan 1, 1996

By E. Topuz

Mining equipment, like all other equipment, is subject to failure. Since most failures occur at random and are unexpected, corrective maintenance is usually more expensive and causes more down-time than preventive maintenance. In order to reduce the number of failures and thereby increase the availability of an equipment or system, preventive maintenance can be scheduled at predetermined points of time. The preventive maintenance scheduling policies presented in this paper utilize reliability and probability theories. They can be applied to various production bottlenecks where high cost equipment precludes having sufficient quantities of stand-by units.

Jan 1, 1982

By R. S. C. Rogers

A mathematical model is proposed as a general formulation for the analysis and simulation of once-through crushing machines. Methods are described which can be used to estimate parameters of the proposed model from experimental data, thus minimizing reliance on backcalculation. The applicability of the model is demonstrated in the analysis and simulation of laboratory and full scale double roll crushers, and with evidence given for a laboratory scale cone crusher. An extension of the model for closed circuit crushing is also described.

Jan 1, 1984

By K. F. Unrug

The research work reported in in this paper deals with the monitoring of roof behavior in a drift mine located in Eastern Kentucky operating in the Coalburg Seam. The thickness of the seam at the monitoring site ranges between 9 and 10 feet with the immediate roof changing from sandstone to shale then back to sandstone. Shale thickness varies between 0 and 2.5 feet. The characteristics of the immediate shaly roof were monitored with 38 dynamometers which were set up in three survey lines to cover the entire range of shale distribution. The dynamometers are capable of providing accurate load readings in the range of +/- 5 pounds. To closely observe the contribution of moisture toward roof deterioration the dynamometers were set up in intake and neutral airways. A television borescoping camera was used in conjunction with the dynamo- metric instrumentations at pre- determined observation holes to physically observe and record the separation process of the shale and sandstone stratum with respect to time. Monitoring took place between January 1985 through January 1986 in order to cover a full cycle of dry and wet mine conditions associated with the seasonal changes. Analysis of the data show a trend of roof deterioration induced by condensation and eventual penetration of moisture within the immediate roof bedding planes, leading to rapid disintegration of the mine roof.

Jan 1, 1986

By Rolf N. Schulz

The recently completed major modifications and additions to Reserve Mining Company's taconite concentrating process incorporate a totally new control system. Design of the new control scheme is centered on reliability, versatility, centralization, and optimization. The design objectives were achieved through a distributed control system based on a network of independent field located micro-processor based control systems connected to a central control room. Operation of each micro-processor can be interrogated and modified from the central control room by the operator or by either of two computer systems. The two computer systems handle logging, alarming, specialized sequenced controls, and complex process optimization routines.

Jan 1, 1980