Search Documents

By Frank X. Bellini, Marc Saidman, Allen J. Hulshizer, Anthony J. Stewart

The cooling water system for the Seabrook Nuclear Station involves 10.25 Km (33,623 ft.) of 6.7 m (22 ft.) OD hard rock tunnels, over one third of which is under and terminating over 1.6 Km (a mile) out in the Atlantic Ocean. The major excavation is accomplished by two TBM's concurrently driving the intake and discharge tunnels which by mid-January, 1981, completed 92% of the excavation. This paper presents the case history of the excavation work and describes a computer program developed to evaluate major activities of TBM excavation on a shift-by-shift basis. Details and summaries of the production efforts are computer plotted in different forms to facilitate the evaluation of production performance, trouble spots and trends.

Jan 1, 1981

By Edward M. Dowey

This paper presents the excavation of the Roosevelt Island Valve Chamber, the final of three chambers in Stage One of New York City's Third Water Tunnel. The valve chamber and passageways 13 379.7 cu m (17 500 cu yd) are drilled and blasted. The rock is stabilized by grouted rock anchors. The 6.1 m (20 ft) diameter shaft is drilled, blasted, rock bolted and wire meshed for a depth of 70.7 m (232 ft). Then shaft excavation proceeds with immediate concrete lining for another 120.7 m (396 ft). Two 6.1m (20 ft) diameter manifolds are excavated using heading and bench. The raise drilling of eight 3.7 m (12 ft) diameter laterals occurs during lower shaft sinking.

Jan 1, 1987

By J. J. Kellar

Researchers have long speculated regarding the adsorption state of collectors on mineral surfaces. Only recently have analytical techniques become available which allow direct in-situ analysis of adsorbed layers. Fourier transform infrared spectroscopy coupled with internal reflection spectroscopy (FT-IRJIRS) with reactive internal reflection elements allows for unobtrusive investigation of the adsorbed layer (Harrick, 1979). This technique has been used both for the in-situ identification of adsorbed species and for the direct calculation of collector adsorption density in real time from infrared spectral data (Miller and Kellar, 1988). The reactive mineral IRE serves both to internally reflect the infrared light and to act as a substrate at which collector adsorption can be monitored. Shown in Figure 1 is a schematic of light being internally reflected in an IRE. As the light is totally reflected at the interface, an evanescent wave propagates a short distance (typically a few microns) away from the IRE, and sampling of the interfacial region occurs. Because of multiple internal reflections, great sensitivity can be obtained. Flotation systems for which this method has been demonstrated include CaF2/oleate, Al2O3/ dodecyl sulfate, CaCO3/oleate, ZnS/xanthate, and KCl/octylamine (Miller and Kellar, 1988; Kellar et al., 1989, 1990; Miller et al., 1990).

Jan 1, 1992

By C. E. Zebula, F. F. Aplan, R. S. Datta

The hydrophobicity of oil shale was found to follow the sequence R-5 > Mahogany >> Eastern. Further, hydrophobicity was found to correlate with the total organic carbon (TOG) content, decreasing with increasing specific gravity of raw oil shale pieces. Differences in hydrophobicity from piece to piece indicate that gravity preconcentration would be much more effective for Western than for Eastern oil shales. Purified kerogen concentrates and low specific gravity fractions (<2.0) of raw Western oil shale samples show critical surface tension of wetting values of [y]c = ~35 mNm -1, and for a kerogen concentrate from an Eastern oil shale [y]c = ~46 mNm-l. This infers that dust from oil shale mining operations can be suppressed by surfactant solutions similar to those used to suppress coal dust.

Jan 1, 1988

By D. C. Seidel, W. K. Tolley

Supercritical water alters the structure of common sulfide minerals by partially removing sulfur from the mineral structure. This discovery has been applied to the treatment of pyritic gold ores to improve precious metal recovery without generating or utilizing environmentally sensitive products such as S02, chlorine, or cyanide. Pretreating pyrite concentrates in supercritical water under mildly oxidizing conditions provided by certain metal oxides or oxygen improved gold leaching using thiourea. The pretreatment differs from chlorination or roast pretreatments in that elemental sulfur rather than sulfuric acid is the major product. A pyritic ore containing 58 g/mt Au was pretreated with oxygenated supercritical water at 24 MPa and 400°C, then leached with 20 g/L thiourea. With pretreatment, gold recovery was 90%; by contrast, gold recovery was below 10% without pretreatment.

Jan 1, 1990

By B. K. Cantrell, K. L. Rubow

The US Bureau of Mines and the University of Minnesota have developed design and performance criteria for a personal diesel exhaust aerosol sampler for underground coal mines. These are based on the premise that size can be used to separate diesel exhaust aerosol, which is mostly submicron in size, from coal dust aerosol, which is mostly greater than a micron in size. The sampler has three stages: a respirable aerosol preclassifier, a 0.8- µm aerodynamic diameter inertial impactor to collect mineral dust and a final filter to collect the diesel aerosol. Using a sample flow rate of 2 L/min and gravimetric analysis to within 0.1 mg, the measure sub-0.8 µm diesel aerosol has an a-priori limit of detection of 0.3 mg/m3.

Jan 1, 1992

By S. A. Rholl

This paper describes the Bureau of Mines experimental test program which evaluated the effectiveness of using high explosives to enhance orebody permeability. To determine the effect of stress on the fracture network generated by blasting, fifteen single-hole laboratory tests in granite blocks up to .067 m3 (2.4 ft3) in size were blasted using .12 to .20m (4.8 to 8.0 in) of 1.6xl0-3-, 3.2xl0-3-, or 6.5xl0-3-kg (25-, 50-, or 100-grain) detonating cord. In situ stresses were simulated using polyaxial load cells to apply uniform stresses of 1.72xl06 to 1.76xl07 Pa (250 to 2550 psi). All of the blocks were sawed to expose the blast-induced fracture patterns for analysis.

Jan 1, 1991

By L. Xu

Since the establishment of the standard dust concentration of 2 mg/m3, a strong effort has been made by mining engineers and researchers to provide better dust control equipment and procedures for underground coal mines. Particular areas of success have been control of dust generation by better coal-cutting strategy, better design of water sprays for dust suppression and air movement, use of scrubbers, and improved design of face ventilation systems. A drastic improvement occurred over time such that the average dust concentrations for continuous miner operators dropped from 6.5 mg/m3 in 1968 to 1.3 mg/m3 in 1980 and for auger, cutter, longwall, and roof bolter occupations from 2.7 mg/m3 in 1973 to 1.6 mg/m3 in 1980 (Niewiadomsky, 1983).

Jan 1, 1990

By C. Y. Kao, Roger Y. Cheng, C. S. Hsieh

The mushroom-shaped Minghu power cavern located in central Taiwan is 21.2 m (W) by 40.5 m (H) by 127.2 m (L) and is designed to house 4 units of power generating-pumping equipment with a total capacity of 1,000 MW. This paper presents an introduction to the geological conditions at the cavern site; the rock mechanical tests undertaken; the design approach adopted; the construction method and sequence followed; and the instrumentation provided in the roof arch to monitor the behavior of the surrounding rocks. The measured data collected from the embedded instruments will be compared with those obtained from theoretical analyses and presented in this paper. Several technical problems encountered during the construction stage are covered and the solutions of these problems are also described therein.

Jan 1, 1983

By Adrian Smith, Debra W. Struhsacker

13.1 INTRODUCTION Cyanide is, a generic term indicating the presence of the cyanide ion (CN-). Cyanide is a very common, naturally occurring compound produced by many biochemical reactions. Many plant species synthesize organic compounds which contain cyanide in the form of cyanogenic glycosides (Knowles, 1976). For example, trace amounts of cyanide are present in the seeds and leaves of many members of the Rosaceae (rose) family (Kingsbury, 1964). Many common items such as lettuce, maize, sweet potatoes, kidney beans, (Oke, 1969) almonds, and cigarette smoke contain cyanide. As examples, a recent chemical analysis of chocolate-covered almonds measured a total cyanide content of about two ppm (Steffen Robertson and Kirsten, 1987); and the U.S. Surgeon General (U.S. Department of Health, 1964) has shown that cigarette smoke contains up to 1,600 ppm total cyanide. The chemistry of cyanide solutions is complicated because the cyanide ion forms compounds and complexes with many elements. Some cyanide species are highly toxic whereas others are relatively inert and harmless. Molecular hydrogen cyanide (HCN) is the most toxic form of cyanide. Under most conditions, HCN exists as a gas which readily dissipates or reacts with the environment to form less toxic or nontoxic forms of cyanide. Thus HCN is an ephemeral toxin, and many naturally occurring geochemical processes reduce the HCN concentration of a heap system with time. As discussed below, free cyanide includes the two species, ionic cyanide (CN-) and molecular hydrogen cyanide. Free-cyanide toxicity in man, mammal s, and aquatic species is we1 1 documented (Doudoroff, 1976; Ecological Analysts, 1979; Towill et al., 1978). The lethal doses reported for human adults vary with the type of exposure as follows: • One to three mg/kg body weight if ingested; • One hundred to 300 ppm if inhaled; and • One hundred mg/kg of body weight if absorbed. Acute toxicity of free cyanide to freshwater invertebrates ranges from 0.028 to 2.295 mg/l, depending on species and test conditions. Generally, free-cyanide concentrations greater than 0.1 mg/l are expected to kill sensitive species in freshwater or marine environments (Doudoroff, 1976;

Jan 1, 1988

By José Ricardo Lopes, Alaor Coelho, Marco Gomes, Alfredo Dacio Moraes Filho, Akira Koshima

"Very low strength alluvial peat soil was found under two old drainage galleries with just 4.3m cover above a twin tunnel due to be excavated by a 10.6m diameter EPB Shield for São Paulo Metro’s Line 5. Alignment was required to strengthen soil and drive the TBM through safely without damaging the galleries. The design included six levels of self-drilling forepoling with lengths up to 15m, using 100 mm-diameter SCH160 metal tubing and injection bulbs with estimated 0.20m diameter. Two 6m-diameter circular shafts were excavated along the shield-tunnel axis, one each side of the galleries, and forepoling fanned out under gallery foundations. Given the peculiar soil and confined working space, more data were needed for correct drilling geometry. Ground mass treatment was successfully designed and executed and galleries were fitted with instruments to enable the shield’s advance. DESCRIPTION São Paulo Metro’s Line 5 (aka Lilas or purple line) is adding 11 stations along an 11.5km extension and three EPB TBMs are being used simultaneously (three EPBs on the same job for the first time in Brazil) with one of them excavating a large cross- section twin-track tunnel. Currently the largest work-in-progress for São Paulo Metro, this project has been divided into seven lots and 9km are already operational. This study refers to Lot 6 where the 10.6m - diameter EPB shield excavation is only 4.3m below two galleries running through a 10m layer of very soft peat soil in an old alluvial riverside region ringed by major roads. After recent filling, this area (Parque das Bicicletas) was used for recreation, although temporarily it has become a construction site. This paper will describe the original basic design; precautions in relation to the structural condition of the galleries after inspection; the problem of absence of data for their foundations; subsoil bore tests; evolution of the engineering design for the galleries and conditioning and reinforcing the soft soil below the galleries to ensure safe advance of the EPB shield, and finally the successful outcome of the solution used."

Jan 1, 2016

By W. E. Benton

The name Perlite applies to both a hydrated volcanic glass containing from 2% to 5% combined water and to the lightweight material that is produced from expanding the sized volcanic glass. Upon heating, Perlite expands to about twenty times its original volume which results in a material of low density, low thermal conductivity, and high sound absorpt&apos;ion. Perlite ore is mined by open pit methods and is crushed and sized to provide specific gradations for expanding into products used in acoustical tile, built- up roofing, filtration, lightweight concrete and horticultural applications, among others. In 1983, the U.S. production of crude Perlite came from 12 mines and 6 western states, with apparent consumption and production estimated to be about 6% lower than 1982. The average price per ton was slightly higher than in 1982.

Jan 1, 1984

By Clark D. Harrison

This paper compares the ash slagging potential of Illinois No. 6 Seam coal: as raw coal; as commercially cleaned coal processed in a baum-jig plant; and as coal cleaned to a reduced ash specification at the Electric Power Research Institute&apos;s Coal Cleaning Test Facility. The comparison is based on: ? ASTM ash fusibility data ? A slagging index ? Gravity fractionation analyses of critical mineral matter compounds ? Comparative pilot combustion tests. The first three grounds of comparison are laboratory data; and the final comparison involves burning approximately 15 tons of each coal at CONOCO&apos;s 1.5 MBtu/hr (440 KW) test combustor. The evidence of these .four comparisons indicates that lowering the ash specification of coal before combustion can significantly improve the ash slagging characteristics of Illinois 90. 6 Seam coal.

Jan 1, 1984

By Fathi Habashi

THE MOST important arsenic minerals are shown in Table 6-1. The recovery of arsenic from arsenic sulfides is treated in Chapter Four. Arsenical ores may be either leached directly, or first smelted to volatilize as much arsenic and sulfur as possible, and the resulting product, called speiss, is then leached. A speiss is mainly a complex mixture of metal arsenides, but its [Table 6-1. Arsenic minerals. Arsenides Niccolite NiS Smaltite CoAs2 Skutterudite CoAs3 Sulfarsenides Cobaltite CoAsS Enargite CuaAsS4 Arsenopyrite FeAsS Arsenic sulfides Realgar As4S4 Orpiment As2S3] composition varies widely, depending on the type of ore treated. A speiss usually contains 15-35% arsenic. Methods of leaching are describedd in the following paragraphs.

Jan 1, 1970

When a company like Lonmin, the third largest platinum producer in the world, is mining one of the most precious metals in the world, time is money. Every piece of equipment is expected to be in top shape because every minute of downtime can add up to lost profit. Two different types of platinum ore are mined and processed by Lonmin, namely Merensky and UG2. Merensky has a grade of 3.5 g/t (0.1 oz/st) and UG2 has a grade of 4.5 g/t (0.13 oz/st). The mine also produces platinum group metals (PGM), which consist of platinum, osmium, palladium, rhodium, iridium and ruthenium. Although South Africa has more than 80 percent of the world?s PGM reserves, these minerals are very scarce. Lonmin is considered a low-cost producer of these minerals, generating 21.5 t (694,000 oz) of platinum and 18.6 t (600,000 oz) of PGMs in 2012. So when the company?s Karee K3 concentrator plant in Rustenburg, North West Province, South Africa, was experiencing high operating costs on the transfer points, a solution was needed.

Jan 1, 2012

With commodity prices rising again and market conditions stabilizing, the Metals Economics Group (MEG) found that most mining companies increased their exploration budgets in 2010. In the groups 21st edition of the Corporate Exploration Strategies (CES), MEG found a 44-percent rise in the estimated worldwide exploration total for 2010. MEG found that the estimated total 2010 budget for nonferrous metals exploration reached $12.1 billion, reinstating almost two-thirds of the industry?s $6 billion in cuts to exploration in 2009. Nonferrous exploration refers to expenditures related to precious and base metals, diamonds, uranium and some industrial minerals; it excludes iron ore, aluminum, coal, and oil and gas. In 2008, exploration budgets were at an all-time high of $14.4 billion. This capped a six-year run in which budgets rose. In 2009, nonferrous exploration budgets dropped 42 percent in 2009 as the global economic crisis and declining prices for almost all commodities took their toll on the industry. Metals prices - the primary driver of exploration spending - have improved markedly since bottoming in early 2009, and have traded well above their long-term trends throughout 2010. In response, major, intermediate and junior companies have all increased their aggregate exploration allocations in 2010. In particular, the significant improvement in the availability of equity financings for the juniors over the past 12 to 18 months has allowed this group to account for the largest share of the overall increase in exploration spending this year.

Jan 1, 2011

By E Marambio, R Brändle, G Fischer, G von Rickenbach, L Burgos, R Luis Fonseca

Ground support systems must provide safe and effective designs for underground excavations under high stress conditions. These systems must be capable to resist dynamic impacts and yielding during the loading process. In this context dynamic testing of the reinforcement and retaining elements that compose the ground support system are required to study and improve the behaviour of these elements under dynamic load events. During the last years, Geobrugg has been working on the improvement of retaining products by testing them in a large-scale impact test facility located at Walenstadt, Switzerland. The test facility is composed of a double level platform with a square-shaped pyramidal trunk geometry, in the upper level housing a loading mass that drop from a height up to 5m. The loading mass is guided by one central steel pipe, and the impact occurs in the sample to be tested located at the lower level in a slab with an area of 3.6m × 3.6m where the ground support system is installed. During the last years, this innovative facility has been used to test several configurations of ground support systems. The results of these tests have enabled to improve the understating of the behaviour of ground support systems under dynamic loads. In this manuscript, the arrangement, measurement, results, and the preliminary analysis of a single impact dynamic test performed during 2021 of a ground support system with a high-tensile steel wire mesh MINAX 80-4.6 is presented.

Apr 26, 2022

By Heinrich H. Becker, Vladimir L. Konyukh, Sergey P. Koltsov, Valery A. Davidenkol

Ramifide conveyor transport of the biggest russian coal mine "Raspadskaya" is simulated by Petri nets. There are 6 longwalls with accidental output. 12 belts, and 5 transfer bunkers at this mine. It is necessary to coordinate transport links for recon- structed conveyor system. Many tasks were solved by dynamic simulation, such as estimation of transport lateness, influence of transfer bunkers on an unevenness of total coal flow, maximum filling of each bunker, maximum time of main conveyor refusal, co-ordination of unloading for dependent bunkers, choice of main conveyor. The problem of mine-wide conveyor transport animation for dispatcher is formulated in reference to mine "Komsomolets". OBJECT OF SIMULATION The biggest russian coal mine "Raspadskaya" is situated on a south part of Kusnetski coal basin (West Siberia). One mines about 20.000 tons of coal out of flat seams by 2.2-4.5 m thickness in a day. There are 6 fully- mechanized longwalls by output 720- 3600 tons in a shift in mine. Coal haulage to surface is carried out by 12 belts having 1.6 - 4.3 km length. For a smoothing over un- evenness of coal flows 5 transfer bunkers to 300 tons were intro- duced. The designed conveyor system is divided into two parts (Figure 1). In the upper part some coal from Face 1 comes through belt road C, into transfer bunker 8,. From the opposite side that bun-

Jan 1, 1996

By W. M. Shaver, R. Letourneau, W. R. Dengler

Dynatec Mining Limited contracted to sink a 1500 metre (4960 ft.) concrete lined shaft for Falconbridge Nickel Mines in Sudbury, Ontario, Canada. The shaft is 6.3 metres (20.5 ft) in diameter inside the concrete lining and is equipped with steel furnishings. Dynatec used the owner supplied 4.6 metre (15 ft.) diameter double-drum hoist to sink the shaft with 12.5 tonne buckets for muck removal and 4 cubic metre concrete buckets for concrete placement. One of the unique features of the shaft sinking operation is the use of a four-boom electric hydraulic drill jumbo permanently mounted in the shaft sinking stage. This paper will describe the performance obtained with the electric hydraulic drilling equipment and the high capacity muck removal and concreting equipment.

Jan 1, 1991

By Joaquin Ruiz

Although Mexico is known for its important base-and precious-metal deposits, and lately oil, some industrial minerals play an important role in the Mexican economy. Sulfur, the most important industrial mineral produced, accounts for approximately 7.5 percent of the total value of mineral production. This commodity is followed by fluorspar, which accounts for 6.4 percent. Predominantly, the fluorspar deposits are very high grade (75 percent CaF) and are contained in lower Cretaceous limestone in the states of Coahuila and San Luis Potosi. Base-metal deposits in the area of Parral (notably San Francisco del Oro), however, have become important fluorite producers in their own right. (San Francisco del Oro has 12 percent fluorite gangue.) Salt from the Guerrero Negro solar-evaporation ponds in Baja California account for 6 percent of the total shares; phosphate from Baja California also accounts for 6 percent. Barite from man to deposits in Lower Cretaceous limestone in Coahuila and exhalative deposits in the Paleozoic section of Sonora account for 1.0 percent. In addition, Mexico is an important producer of gypsum, graphite, and celestite. Although graphite and celestite are not large-scale operations and thus do not contribute much to the Mexican economy, the Mexican graphite and celestite deposits are among the most important in the world; Mexico is one of the world&apos;s few sources of celestite. The celestite is in the form of large, high-grade mantos in Cretaceous limestones in northern Mexico.

Jan 1, 1987